Military Engineer Services Tender

Material & Labour for pre painted gavalume aluminium zinc coating Galvanised Iron based Plain steel sheet 0.50mm thick of an colour having tensile strength 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screrws, complete all as specified & directed.

Dismantling floors, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises, complete all as specified & directed.

Material & Labour for Vitrified Ceramic tiles as light shade 9-10 mm thick (square/ rectangular)polished, area of each tiles not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, complete all as specified & directed.

Material & Labour for Vitrified Ceramic tiles as light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, complete all as specified & directed.

Material & Labour for Screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 for laying floor finishes, complete all as specified & directed.

Material & Labour for Rendering 10mm thick on fair faces of brick work or concrete surfaces with cement mortar 1:4 as in backing coat of skirting /dado, all as specified and directed.

Material & Labour for preparing new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified & directed.

Material & Labour forr preparing new steel and iron surfaces of any description not exceeding 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified & directed.

Material & Labour for False ceiling with 12.5mm thick Gypboard plain board including all necessary fittings and fixtures , which includes gypsteel ULTRAtm CRP surface ribbed perimetre channels (having one flange of 20 mm and another flange of 30 mm and a web of 27 mm) along the primeter of ceiling screw fixed to brick wall/ partition with the help of nylon steeves and screws, at 610mm centres.Then suspending Gypteel ULTRA tm CRP surface ribbed intermediate channels of size 45mm (with two flanges of 15mm each) from the soffit at 1220mm centres with Gypsteel ULTRA tm CRP surface ribbed ceilling angle of width 25mm x 10mm fixed to soffit with GI cleat and steel expansion fasteners. Then Gypsteel ULTRA tm CRP surface ribbed Ceiling section of having web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the Gypsteel ULTRA tm intermediate channel with the help of connecting clip and in direction prependicular to the Gypsteel intermediate tm channel at 457mm centres. Single layer of 12.5mm tapered edge Gypboard Plain (confirming to IS 2095 part 1 1996) is then screw fixed to ceiling section with 25mm drywall screws at 230mm centres. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attatchment. Finally square and tapered edges of the boards are to be jointed and finished so as to have flush look which includes filling and finishing with Gyproc jointing compound, Gyproc joint paper tape including Painting of Gypboard Ceiling / Partition / Walls with two coat of ceiling putty, two coats of primer and two coats of oil emulsion paint finished with roller finish, complete all as specified & directed.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 Sqcm in section, complete all as specified & directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete all as specified & directed.

Dismantling ceiling boards any description any thickness including cover fillets, all as specified and directed