Kamarajar Port Limited Tender

Supplying, and fabricating TMT Fe 500D bars for reinforcement and placing it in position for all RCC members as shown in the drawing including handling, cutting, bending and tying with 1.25 mm dia black annealed binding wire wherever required including all materials, labour, lifting, tools, equipments, etc., complete. Note: The rate shall be inclusive of cost of steel, binding wire and fabrication charge etc., complete.

Providing and laying Ceramic glazed tile for dadooing in Kitchen area for cooking platform using first quality tiles of approved brand (Johnson’s or equivalent) of size and thickness to match with the existing tiles set in C.M 1:3 (1 cement: 3 fine river sand) 12mm average thick and fixing the tiles with neat cement slurry to required slope and joints neatly pointed with white cement added with pigment to match the colour of the tiles, curing all as per relevant specification and as directed including all materials, labour, tools, equipments etc., complete

Providing and fixing cuddapah Sink of size 1'6" x 2' or to match with the existing arrangment to the kitchen area as per relevant specification and as directed including all materials, labour, tools, equipments, transport, fuel, etc., complete

Providing and fixing in position First class country wood (padauk) wrought main frames for door frames with necessary M.S. hold fasts / clamps fixed suitably to the masonry / concrete including cutting pockets and grouting with P.C.C. 1:3:6 (1 cement : 3 coarse river sand : 6 hard granite graded stone aggregate of 20mm nominal size) in volumetric proportions, curing including painting with one coat of boiling coal tar paint on the portions of the timber abutting against masonry / concrete all as shown in the drawing and as directed including cement and all other materials, labour, tools, equipment, etc., complete.

Providing and fixing in position flush door shutters of suitable thickness to replace the existing doors commercial non decorative type, water proof, core of block board construction with frame of kiln seasoned and preservative treated hard wood shutters with external lipping all machine pressed with phenol formaldehyde synthetic resin fixed with anodized aluminium butt hinges with nylon washers , anodized aluminium tower bolt necessary locking arrangements such as anodised aluminum aldrop with metal screws all as per drawing including all labour materials etc., complete.

Providing and fixing in position good quality country wood (Padauk or equivalent) panelled Glazed shutters for windows & ventilators to match with the existing thickness including required aluminium fittings all as per relevant specifications and as directed including all materials, labour, tools, equipments etc., complete.

Supplying and fixing anodised aluminium (AC 10 grade) fittings for doors, windows etc., with necessary screws all as per relevant specification and as directed including all materials, labour, tools, equipments etc., complete.

Tower bolt 200mm long

Aldrop 200mm long

D type Handle -100mm long

Butt hinges 150 mm long with nylon washer

Providing and fixing GI pipeline for waterline to match with the existing diameter for Bathroom and Toilet including providing necessary GI Specials like bends, shoes, specials etc., all as per relevant specifications and as directed including all labour, materials, tools, equipments, scaffolding etc., complete.

Providing and fixing uPVC Pipes for waterline of suitable diameter of approved make like Truebore or Finolex or equivalent approved make with specials like tees, bends, couplings, elbows, reducers, unions, etc., including all labour, materials, tools, equipments, etc., complete

Providing and fixing uPVC Pipes for Sewerline of suitable diameter of approved make like Truebore or Finolex or equivalent approved make with specials like tees, bends, couplings, elbows, reducers, unions, etc., including all labour, materials, tools, equipments, etc., complete

Providing and fixing approved quality PVC gate / ball valve to the pipe line including testing the valves and joints etc., all as directed including all labour, materials, tools, equipments, etc., complete.

Supplying and fixing best quality Indian water closet of size and shade as specified vitreous ware of approved make and quality with ‘P’ or ‘S’ trap with fittings, the closet being fixed in a 15 cm thick cement concrete 1:5:10 cushion (1 cement : 5 fine sand : 10 brick aggregate 40mm nominal size) including necessary river sand filling concrete backing around the closet 1:5:10 cushion (1 cement : 5 fine sand : 10 brick aggregate) including all as specified and as directed including all labour, materials etc., complete.

Providing and fixing good quality vitreous white wash hand basin 630mm x 450mm size or nearest size as available in the market with a single 15mm C.P. brass pillar tap, C.P. waste fitting, 32mm dia C.P. brass union, 15mm dia PVC inlet connection, 32mm dia PVC waste pipe fittings, a pair of PVC /cast iron brackets etc as available in the market suitable for fixing the wash hand basin, including fixing the brackets with teakwood plug and making good the disturbed portion, etc., all in sound working condition all as per relevant specification and as directed including all materials, labour, tools, equipments etc., complete.

Providing and fixing 15 mm dia. C.P. Brass Bib cock long body/short body to suit the site condition of standard brand available in the market including cost of all materials, labours ,tools ,etc., complete as per specification and as directed at site.

Supplying and fixing factory made PVC door of size 0.90m x 2.10m or to suit the door opening with frame of size 50 x 47mm with a wall thickness of 5mm rigid PVC foam sheet Mitered cut at two corners and joined with 2 nos MS “L” brackets of 15mm square in the size 150 x 150mm. The PVC door frame is reinforced with 19 19mm MS Square tube 19 gauge and it will be reinforced by county wood. The door frame shall be fixed to the wall by drilling 100mm long MS screws by using PVC fasteners. The door should by of 30mm thick factory made solid panel PVC door structure of MS tubes of 19 gauge thick and 19 x 19mm for stiles, 15 x 15mm for top and bottom rails. MS frame shall be covered with 5mm thick each moulded PVC “C” channel (mat finish) of size 50mm x 30mm for stiles with 5mm thick PVC sheet, 70mm wide PVC sheet for Top rails and bottom rails, panelling of 5mm thick sandwich in the MS frame sealed to the Stiles and rails with 30 x 5mm thick PVC sheet beading on either side and jointed together with solvent cement adhesive including 2 Nos 150mm aluminium tower bolt, 1No 150mm aluminium aldrop and 2 no 150mm Aluminium handles including all labour, material, equipments, tools, plants, etc. complete.

Providing and fixing in position PVC Nahani trap (floor trap) 110mm dia with gratings as available in the market suitable for PVC pipe and embedding the trap in the floor slab of concrete with suitable gradient making the joints water tight etc., all as directed at site of work including curing, all labour, materials, tools, equipments etc., complete.

Preparing the suface of the walls and painting with two coats of colour painting over one coat of primer of approved brand and Colour to give an even shade all as directed including all materials, labour, scaffolding, tools, equipments, brushes, etc. complete.

Preparing the surfaces of wooden doors, windows and ventilators and Painting with two coats of synthetic enamel paint over one coat of primer or equivalent paint of approved colour to give an even shade all as directed including all materials, labour, scaffolding, tools, equipments, brushes, etc. complete

Supplying, Installing and commissioning of Point wiring for light, fan, Fan Regulator, 6Amps switched sockets with 3Run 1.5 Sqmm, 2.5Sqmm multi strand single core copper conductor wire drawn in 1" Dia in Open PVC conduits, bends,Tees, Junction Box using clamp. The work also involves supply and fixing of 6A switch housed in manufacturer's Wooden Box to be fixed in wall. The switch with suitable Hylam Sheet and Wooden Box and Holder (Straight & Angle) with Ceiling rose for the points shall be located at appropriate locations including all materials, labour, tools, tackles, etc., complete as directed by the KPL Engineer Note: The approximate cable length between switch to Electrical fitting is about 5mts The Electrical Cable should be of make Finolex/ Kundan/ Polycab/ Havells The Electrical Switches & Socket should be of make Legrand/ GM/ Anchor/ Havells/Polycab

Providing LED Tube Light Fitting with necessary Electrical Cable including all materials, labour, lifting, tools, equipments, etc., complete. Note: The LED Tube Light Fitting should be of make Philips/ Syska/ Wipro/ Bajaj

Providing Double Pole MCB 16Amps with necessary Electrical Cable including all materials, labour, lifting, tools, equipments, etc., complete

Providing 16Amps 2 PoleMain Switch with Fuse Unit and necessary Electrical Cable including all materials, labour, lifting, tools, equipments, etc., complete.

Providing Electrical Calling Bell with Switch & Boxincluding all materials, labour, lifting, tools, equipments, etc., complete.

Providing Electrical Earthing connection with necessary Eart Pit & Anode Rod, Copper Wire including all materials, labour, lifting, tools, equipments, etc., complete.

Providing and fixing Aluminium Zinc Alloy coated sheet (Galvalume) of standard size available in the market of Total coated thickness (TCT) of 0.47mm – 0.50mm for roofing with coating thickness not less than 150gsm and tensile strength not less than 550 MPa. The steel shall have a Zinc- Aluminium alloy coating of 55% Al, 43.4 Zn % with normal profile, the sheets shall be fastened with the structural system using self drilling steel screws coated with tin and zinc, Stitch Screws or Crest screws as required shall be adopted. Using Screws in valleys (especially in roof) is not permitted. Good quality EPDM washers and caps shall be used all as specification drawings and as directed including all labour, material, equipments, tools, plants, etc. complete. Note: 1. The measurement of the sheet area will be measured for the area covering the roof. 2. The lap area will not be measured for payment. 3. The length of the sheet will measured aligned which includes bend portion.

Providing and fixing Aluminium Zinc Alloy coated sheet (Galvalume) Ridge piece of standard size available in the market of Total coated thickness (TCT) of 0.47mm – 0.50mm for Cladding with coating thickness not less than 150gsm and tensile strength not less than 550 MPa. The steel shall have a Zinc- Aluminium alloy coating of 55% Al, 43.4 Zn % with normal profile, the sheets shall be fastened with the structural system using self drilling steel screws coated with tin and zinc, Stitch Screws or Crest screws as required shall be adopted. Using Screws in valleys (especially in roof) is not permitted. Good quality EPDM washers and caps shall be used all as specification drawings and as directed including all labour, material, equipments, tools, plants, etc. complete.