Hindu Religious Institutions And Charitable Endowments Tender

Supplying and filling in foundation and basement with Gravel in layers of not more than 15cm thick well rammed watered and consolidated etc.,

Supplying and filling in foundation and basement with M sand in layers of not more than 15cm thick well rammed watered and consolidated etc.,

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid) a)For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

b)For rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

c) For Circular RCC columns, , etc.

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

Providing and laying in position, standardised concrete Mix M25 grade in accordance with IS 456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of work with minimum cement content of 350 Kg/m3 and maximum water cement ratio of 0.50 including admixyure (Plasticiser / super plasticiser ) in recommended proportions as per : 9103 to accelerate retard setting of concrete, improve workability without impairing strength and durability with about (5Cum) 7730kg. of 20mm machine crushed stone jelly and with about (3.3cu.m.) 5156kg. of 10-12 mm machine crushed stone jelly with about 4.79Cu.m. )7670kg. of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering and also including laying , vabricating with mechical vibrators, finishing curing etc., and providing fixtures like fan clamps in the RCC floor/ roof slab where ever necessary without claiming extra ,etc., complete.complying with standarde specification and as directed by departmental officers.The coarse and fine aggregates to be used should compling with the requirements of IS Standards. ( No separete payment will be made by the department for excess usage of materials) a) Foundation and basement

b) Ground Floor

c) First floor

d) Second floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Cement Concrete 1:3:6 (One Cement, Three CS sand and Six broken stone jelly) using 40mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. (Reinforced Cement Concrete 1:2:4 for slab to be extended upto top of splashing with pressed tiles and future extension rods to be embedded in CC 1:3:6 (One Cement, Three Sand and Six hard broken stone jelly). Dummy columns should be at least 1 metre height)

Brick work in following Cement Mortar 1:5 (One cement Five CS sand ) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-1/4" for foundation and basement including curing, etc., complete complying with standard specifiction. a)Foundation and basement

Brick work in following Cement Mortar 1:6 (One cement six CS sand ) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-1/4" for foundation and basement including curing, etc., complete complying with standard specifiction. a) Super structure in ground floor

b)Super structure in First floor

c)Super structure in second floor

Brick partition walls of 10.80cm thickness using best quality country bricks of size 8-3/4" x 4-1/4" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately) a)Foundationj and basement

b)Ground floor

c)First floor

Supplying, fabricating, erecting and fixing Hilux (or) Equivalent board false ceiling upto a ceiling height of 4.5m from floor level.Using Hilux Board plain sheets (10mm thick) etc complet e as directed by departmental officer

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three CS Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five CS sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:3 (One Cement and Three CS Sand) 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Painting two coats of newly plastered wall surface with ready mixed exterior plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed interior plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Paving the flooring with high quality specail coloured and Double charged Virtified tiles of approved quality and brand of size 600mmX600mmx8mm thick for flooring of approved quality and colour set in cm1:3 (one cement an d three sand ) 20mm thick and pointing with white cement using at the rate of 0.40Kg/m2 including finishing the joint neatly ,pointing flush with tiles surface etc,complete complying with standard specification and as directed by the departmental officer.

Flooring with anti skid ceramic colour and design tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three CS Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification.

Flooring with Joint free rectified ceramic tiles of size 305x305x8mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three CS Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification.

Dadooing walls with best approved quality, design colour glazed tiles of size 300mm x450mm x 8mm set in Cement Mortar 1:2 (One Cement and Two CS sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers.

Solid PVC Door Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter

Supplyand fixing teak wood frame for door and windows ventilator wrought and putup including cost of matrerials and labour charges etc., complete as directed by departmental officer

CRCA Frame-Supply and Fixing CRCA pressed steel box secion 18qauge (or) 1.25m thick for door frame including providing hole and fixing with wooden blci for fixing furniture and fitting with one coat of red oxide primer etc., completer

Supplying and fixing solid core particle board flush shutter of nominal thick of 35 mm with necessary T.W.internal lipping conforming to IS 2302 with both sides alround commercial ply 35mm thick including supplying and fixing cost of wind appliances and furniture fittings such as 1no .200x12mm aluminium tower bolt 2nos. 150x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 3 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete as directed by the departmental officers. a)Double leaf

b)Single leaf

Supplyand fixing teak wood shutter for door wrought and putup including cost of matrerials and labour charges etc., complete as directed by departmental officer

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are Reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supply and fixing mild steel grills for windows, ventilator, gate, ladder etc including priming coat.including cost of matrerials and labour charges etc., complete as directed by departmental officer

Supplying and fixing of PVC Sliding Door with Roller The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification.

Polishing the teak wood door with two coat of best french (Lac) polish with approved quality and brand over a coat of been waxing including preparing the wooden surface to recarve polishing etc. Complete complying as per standard specification. (The make quality and colour of french polish wax should be got approved by Executive Engineer before the on wax)

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three CS Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Finishing the top of slopped roof, sun-shade with Machine Pressed Ornamental Tiles of approved quality laid in cement mortar 1:3 20mm thick mixed with WPC at 2% by weight of cement used and top pointed with the same red oxide mixed mortar etc complete, complying with standard specifications

Supplying and fixing in position best approved of ISI quality of PVC rain water down fall pipes having a pressure of 4 Kg./sq.cm including cost of necessry PVC shoe, PVC bend, gratings of required diameter and special clamps, brass screws, nails, etc. and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc. complete. The rate shall be inclusive of cast of removable iron grating. The PVC pipe shall be fixed in wall with special type of clamps. Special type of "U" clamp at the centre of the pipe line shall be fixed in addition to those for more than 3.0 M pipe length complying with standard specification. 160mm dia PVC rain water down fall pipes

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification.

Supplying and fixing in position CP shower rose with CP stop cock arrangement of size 15mm dia inlet and 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications.

Supplying & fixing inposition 15mm dia Chromium Plated brass screw down tap (heavy type) of approved make confirming to ISS and including cost of shellac, thread etc., complying with standard specification and including cutting and threading wherever necessary etc., complete complying with standard specifications.

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm White glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two CS sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Departmental

Supplying and fixing PVC ventilating shaft of 100mm dia with 3 metre height including cost of 100mm dia AC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers

Supply and fixing in poistion CI Manhole covers with CI Frames (Heavy Duty) of size 60 cm x 60 cm as directed by departmental officers.

Supply and fixing in position best quality PVC Soil/ waste pipes 6 kg / sqcm of various size (Above Ground Level) having ISI mark and providing leak proof joints including fixing to the wall with special PVC /MS clamps, etc., and making connection to all sanitory fittings, dismantling masontry / RCC works wherever necessary and making good the dismantled portion to the original condition, complying with standard specification etc., complete. a)110mm dia

b)75mm dia

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works). a)110 mm PVC Elbow

b)110 mm PVC Door Elbow

c)75 mm PVC Elbow

d) 75 mm PVC Door Elbow

Supplying, laying and joining UPVC pipes of approved quality and best veriety conforming to ISS with ISI mark, of the the following size above Ground level up to 4 M hight laid properly to alignment including cutting, threading and fixing the required UPVC specials but excluding the cost of such specials and fixing to the wall with necessary TW plugs, clamps and screws, making holes on the wall or drilling holes in the roof and making good dismantled portion to original condition with necessary brick work, concrete and plastering wherever necessary with necessary scaffolding charges etc., complete. a)32mm dia Upvc pipe

b)25mm dia

c)20mm dia

Supplying and fixing in position UPVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the UPVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The UPVC specials should be got approved by the Executive Engineer before use on works). a)32 mm dia elbow

b)32 mm dia TEE

c)32mm x25 mm Reducer

d)25 mm x 20mm reducer

e)20 mm x 15mm reducer

f)20 mm dia Elbow

g)20 mm dia Tee

Supplying and fixing in position first quality and approved variety Gun Metal Gate valve (Heavy type)/ Wheel Valve (Heavy Duty) with ISI Mark of approved quality of the following dia including cost of shellac, thread, labour charges for cutting, threading,fixing in position etc., for both internel and external water supply arrangements. a)32 mm dia Gate valve

25mm dia Gate valve

Supplying and fixing position CI/PVC Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three CS sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)Nahani Trap of size 100 x 75mm with stainless steel gratings

Supply and Fixing PVC water lank of 1000 Lit including cost of all materials and labour charges etc., complete

Drilling of Borewells anywhere in Tamilnadu including transportation from one place to another with in Tamilnadu in alluvial soil sedimentary strata of clay and sand stone shale pebbles boulders etc. By first taking a pilot bore of 140 mm/150mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs, fuel, labour and drilling bentonite and water required for drilling at site ( Site will be shown by the Dept Officers) including construction of mud pit. a)Depth 0 to 60m

b)Above 60m to 90m

c)Above 90m to 120m

d)Above 120m to 150m

e)Above 150m to 180m

f) Above 180m to 200m

Supplying and fixing of 150mm dia CS PVC casing pipe assembly with slota (or) with out slots in the driilled hole including welding the joints etc complete and supplying and packing the annular space with pebbles of size and quality as approved by the departmental officers etc complete

Supply and fixing of 3.00 HP Submersible pump including Labour charges for errection of Submersible pumpset in borewell all acessories vost and conveyance etc., complete as directed by departmental officer

Supplying and fixing of 3 phase electrical panel Board D.O.L with two level guard and auto start including cost and coveyance and fixing charges etc complete. as directed by departmental officer

Supplying and fixing of 4 core 6 PVC armoured UG cable including cost and conveyance and labour charges etc complete. as directed by departmental officer

Supplying and fixing of HDPE pipe 32mm dia HDPE pipes for 3 HP Submersible pumpset including cost and conveyance of all materials and all labour charges etc complete. as directed by departmental officer

Supply of Suitable dia PVC Nylon rope for submersible motor as directed by departmental officer

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying and fixing of fine Cuddapah slab of 38 / 40 mm thick for Cup - board arrangements in brick wall including levelling to correct alignment etc complete complying with standard specification and as directed by departmental officers

Providing cupboard shelf shutter using 19 mm thick water proof plywood shutter with country wood frame 12 x 5 cm size both vertical and horizontal frame .The edges of plywood shutter should be fixed with 25 x 12mm size teak wood beading .The MS piano hinges 2 Nos each 30 cm long should be fixed in each shelf .3 strip magnetic catcher 4 nos ,100 mm long handle 'D'type 2 nos ,50mm size door lock 1 no ,125 mm long brass pat lock 1 no should be fixed in each shelf .After the completion of the cupboard shutter the plywood areas both inside and outer side and country wood frame areas should be painted with two coats of enamel painting .The rates inclusive of nails ,fevicols,screws etc., complete.

Dry Brick work using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-1/4" for foundation and basement including etc., complete complying with standard specifiction.

Supplying and filling using 20mm gauge hand broken granite stone jelly for foundation and basement including dewatering if found necessary and laid of not more than 15cm thick and compacted. etc. complete complying with standard specifications

Supplying and filling using 40mm gauge hand broken granite stone jelly for foundation and basement including dewatering if found necessary and laid of not more than 15cm thick and compacted. etc. complete complying with standard specifications

Manufacturing and fixing in position of RCC Precast slab CC 1:2:4 - 50mm Thick using 20mm 'size of hard broken granite stone for all RCC works using machine for mixing concrete excluding cost of steel, fabrication of reinforcement, centering, strutting and shuttering and placing the grills in position etc., complete complying with standard specification

Supplying and fixing 63mm paver block with filling stone dust in layers of not more than 15 cm thick well watered, rammed and consolidated including necessary compaction with palte vibrator, etc. Complete

Name Board- Supplying and fixing of Aluminium Dyecast letter of approved size and colour the colour treatment process adieve with RF colour coat and then it processes cloured layer is set into the letter so the heat treatment process for it size of Aluminium Dye cast letter 9" size அருள்மிகு சங்கரநாராயணசுவாமி திருக்கோயில் சங்கரன்கோவில் திருமண மண்டபம்

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with GI Flush mounting box ,plastic combined cover plate and 6A One way modular type (one module) switch with light / fan marking and making good of the concealed portion with suitable color for PVC light point (All switches ,cover plate and GI mounting box should be higher end company make (For light points)

Wiring with 3 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with 1 modular plastic box with cover plate and 6A modular switch (two way) with painting of suitable colour for open PVC staircase light point

Supply and fixing of single box type 4'20W LED fitting with TW round blocks on wall or ceiling with with PVC unsheathed copper leads from terminals to the fitting (LED fittings should be of Higherend company make like philips / cromption etc)

Supply and fixing of 4'20W LED fitting complete with 1.5 mt conduit pipe suspension from the ceiling PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of 2ft x 2 ft (600mm x 600mm) square type LED light fitting with chain link connection (Philips make)

Supply and fixing of 9W LED Bulb for BH point

Supply and fixing of chandlier fitting with LED bulb with connection (MR)

Supply and fixing of WT Bulk head LED Fitting suitable for 15W LED bulb with connection

Supply and fixing of Havells jeta alba flood light 70W LED fitting with necessary wall grouting clamps with fixing bolts on the ceiling with PVC unsheathed copper leads from terminal to the fitting

Supply and fixing of fancy lamp fittings with 9W LED bulb on wall with connections

Supply and fixing of Anchor Roma louvers white foot lamp with 4 module box and tresa cover22025 in grabtree 4 module box with necessary connecetion

Supply and fixing of Entry/Exit light board with connection

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting

Supply and fixing of 1200mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 300mm downrod on the existing clamp

Supply and fixing of 48" AC Ceiling fan complete with stepped electronic 300w regulator with 1mt downrod and existing clamp

Supply and fixing of 450MM 18” Almonard Wall Fan on wall with connection

Supply and fixing of 450mm (18") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall

Supply and fixing of louvers shutters arrangements for 450mm (18") sweep exhaust fan

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fanl

Supply and fixing of 4 KVA capacity automatic voltage stabiliser with time delay relay

Supply, installation, testing and Commisioning of 1.5 ton split type air conditioner unit 5 star rated

Supply and fixing of 1no 6A plug mounted in suitable 1 module Metal surface mounted box with suitable plastic combined cover plate with Connections

Supply and fixing of 1no 6A switch mounted in suitable 1 module Metal surface mounted box with suitable plastic combined cover plate with Connections

Supply and fixing of 1no 16A plug mounted in suitable 1 module Metal surface mounted box with suitable plastic combined cover plate with Connections

Supply and fixing of 1no 16A switch mounted in suitable 1 module Metal surface mounted box with suitable plastic combined cover plate with Connections

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections Higher End

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections Higher End

Supply and fixing of 20A DP MCB Switch in suitable 2 pole sheet steel enclosure with earth connection

Supply and fixing of 40A DP MCB Switch in suitable 2 pole sheet steel enclosure with earth connection

Supply and fixing of 63A MCCB Switch in suitable 4 pole sheet steel enclosure in flush with wall with earth connection

Supply and fixing of 100A MCCB Switch in suitable 4 pole sheet steel enclosure in flush with wall with earth connection

Supply and fixing of 8 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB Isolator as incoming and 24 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 6 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB incomer) with double door (metal door) with 1 no. 160A 4P MCCB switch as incoming and 4 nos. 63A 3P MCB, 6 nos. 6A to 32A SP MCB as outgoing with suitable cable end box in flush with wall with earth connection only. Higher End

Supplying , erection, testing and commissioning of 16SWG CRCA Sheet steel cubical type powder coated distribution board with 3 phase and neutral bus bars of size 25 x 6mm with earth busbar of 25 x 3mm mounted on poceilin insulators and separated with hylam sheet for the fooloowing switches Incoming : 400A 4P MCCB with 400A spreader terminal - 1 no Outgoing : 400A 4P MCCB with 400A spreader terminal - 1 no, 125A 4P MCCB Switch - 4 nos , 63A 4P MCCB Switch - 4nos

Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour

Supply and Run of 2 of 4 sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour

Supply and Run of 4 of 6 sq.mm. (84/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour

Supply and Run of 4 of 10 sqmm (101/0.45) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour

Supply and fixing of 8" x 6" PVC synthetic box for cable connection

Supply and fixng of TNEB meter board suitable for 3 phase 500A service connection made up of suitable angle iron frame work of size 3 feet x 2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 3 feet x 2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 500A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 19/16 PVC insulated copper wire with earth connection complete

Supply and fixing of 3 phase 500A aerial fuse unit for 3 Nos. 500A fuse units (500V) on suitable MS sheet covered with 6mm thick hylem sheet on suitable angle iron work the tapping pole with necessary clamps

Supply and fixing of 400 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply and fixing of 400 A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply and fixing of 65mm (2-1/2") dia G.I Pipe(class-B) of 6 mts length with 300mm x 300mm x 6mm base plate duly welded at the bottom with Concreting with Construction of masonary pedestal with necessary clamps to hold the LTUG Aluminium Service Cable with painting of suitable colour

Supply and clamping of 4 x 16 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 4 x 25 sq.mm. PVC armoured LTUG cable with earth connection

Supply and clamping of 3-1/2 x 35 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 35 sq.mm. PVC armoured LTUG cable with earth connection

Supply and clamping of 3-1/2 x 95 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 95 sq.mm. PVC armoured LTUG cable with earth connection

Supply and clamping of 3-1/2 x 240 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 240 sq.mm. PVC armoured LTUG cable with earth connection

Supply and clamping of 3-1/2 x 300 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 300 sq.mm. PVC armoured LTUG cable with earth connection

Supply and run of copper flat of size 25mm x 3mm on wall or in ground for earth connection (Panel board to ISI earthing)

Supply and run of 1 of No.8 SWG copper conductor on suitable PVC rigid pipe on wall with painting of suitable colour for earth connection

Earthing as per the ISI specification with an earth electrode of 2.10mt, 38mm copper earth electrode with 25kg chemical powder with 450mm x 450mm x 300mm RCC concrete box on the earth pipe with RCC Cover slab and S.S hand lifting clamps

Supply, errection, testing and commisioning of 1 no 200KVA Kirloskar generator set with following accessories as specified below. with accessorer enclosing confirming to CPCB with name and BIS Specification. Voltage :415V Dry Weight :3900kg Noise Level :75 dBA Model Number :KG1-200WS Rating :200 kVA Brand Kirloskar Frequency :50 Hz Power factor :0.8 lagging Governing class :G3 Fuel tank capacity :460 Ltrs Overall dimensions :4340 x 1740 x 1970mm Electrical Battery starting voltage :24VDC Including the foundation bed and AMF panel board

Supply, Erection, Testing, Commissioning and Handing over of 1 no 13 persons capacity passenger lift gearless type without machine room as per following technical specifications including all taxes and duties. Technical Specifications: 1. Location : 300 person's Marriage Hall in Arulmigu Kasi Viswanatha Swamy Thirukoil at Tenkasi in Tenkasi District 2. No of Lift : One No 3. Type of Lift : Passenger lift 4. Capacity of Lift : 13 Persons Passenger(1105Kgs) 5. Speed : 1.00 mtr/Sec 6. Type of Drive : Microprocessor based specific variable voltage variable frequency V3F Drive with enhanced ride comfort and near zero leveling functions 7. No of floor : Ground +1 floors 8. Total Travel: 8 Mtrs approximate 9. Leveling Accuracy : High level acccuracy with smooth & Jerk free stopping. 10. Construction of car: Special car made of Stainless Steel Hairline finish No.4 hair line finish & panels with direct lighting and new beautiful single tile false ceiling with tubular handrail and mirror. 11. Position of Machine: Gearless lift without machine room 12. No of Landing Entrance: One in front 4 Nos only. 13. No of Car Entrance: One in front only. 14. Car Entrance Door: Centre opening automatic power door with stainless steel No.4 Hair Line finish with view panel. 15. Landing Entrance Door: Center opening automatic power door with stainless steel No. 4 hair Line finish with view panel. 16. Lift well: 2100mm (width) x 2000mm (depth) available size. 17. Lift pit depth available: 1600mm 18. Car size: 2000mm wide x 1100mm deep x 2300mm height (Part 1-2000). 19. Car clear opening: 800 mm x 1600 mm (as per IS 14665 (Part-1)-2000). 20. Power supply: 415V, 3 phase, 50 cy /sec A.C supply for power and 230V, 50 Hz single phase AC supply for light. 21. Control: Micro processor computer based - simplex collective full collective logic system with / without attendant mode. 22. Car fittings 4 Nos 8W LED recess mount fixture lighting with cross flow fan 23. Lift Well: RCC construction with brick masonry. 24. Indication: Up/Down Digital Direction scroll type and position indicator for all landing and in car. 25. Emergency Alarm Bell: Battery operated Alarm Bell to be provided with automatic charging device. 26. Emergency Light: Battery operated Light to be provided with automatic charging device. 27. Fireman's switch: To be provided at ground floor. 28. Minor Builders Work: To be provided by lift contractor. 29. Scaffolding: To be provided by lift contractor. 30. Stainless Steel sill angles and facia Plates: To be provided by lift contractor. 31. Steel for lift Machinery: To be provided by lift contractor. 32. Servicing and Maintenance: Free Comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year. 33. Provision of 1+3 EPABX intercom with phone to be provided at the following places,vide i.Lift Head Room, ii. Reception Room and iii. Inside the Lift, by lift contractor. 35. Lift License: Preparation of drawing, Payment of charges to CEIG and Insurance policies if any and obtaining CEIG safety certificate and lift license as per lift act should be done by lift contractor. 36. Automatic rescue device - To facilitate the landing of the nearest floor at the time of power failure. This shall consist of suitable type battery system with charges inverter under voltage protection system etc. 37. Floor annunciation system with music. 38. Special futures: (a). Infra red door sensor withFull height screen. (b). Full width half height rear panel Mirror. (c).Voltage stabilizer for circuit control. (d). Tubular Stainless Steel hand rail three sides in car. (e). Signal Fixtures (f). Vandal proof S.S. button with S.S. (g). Stainless steel door frames (h). V3F door operator (i) Call register signal (j) Pit ladder (k). Braille buttons (l).Stainless steel facia for car operating panel and landing fixtures. (m). ON-OFF switch for fan and light. (n) Over load warning indicator. (0) Fire rating: 60 Mins. 39. Over speed governor, phase failure and phase reversal relay, alarm bell, Guide brackets for car and counter weight, rubber padding under winding unit, Motor of adequate capacity, single reduction worm gear, electromagnetic brake with compression springs, car safety gears, buffer, electro mechanical door locks, emergency key, side supporting angles, motor over load protection devices, final limit switch, main suspension ropes, counter weights, lifting joint joist for mounting the machineries. 40. Guarantee: Guarantee for the materials & workmanship of equipments complete should be offered by the Lift firm for a period of not less than one year. 41. Site testing in accordance with IS 14665 should be carried out at the time of handing over (PWD SR)

For the stage Area of 103.67 Sqm Supply, Installation, testing and Commisioning and Handing over of Air cooled self contained 5.5 TR Ceiling suspened Ductable Unit

For the Mariage Hall area of 487.70 Sqm Supply, Installation, testing and Commisioning and Handing over of Air cooled self contained 11 TR Ceiling suspened Ductable Unit

Supply, Installation, testing and Commisioning and Handing over of Air cooled self contained 17 TR Ceiling suspened Ductable Unit

Low Side works Supply and Installation of Factory Fabricated Rectangular Ducting-22G

Supply and Installation of Factory Fabricated Rectangular Ducting-24G

Supply and providing of pipeline nitrle rubber insulation for Refrigerant and drain pipe lines.

Supply and providing thermal insulation of 9mm thick vidoflex with Aluminum Foil

Supply and Fixing of Flexible Canvas Connection

Supply and fixing of extruded aluminum powder coated, Supply and return Air Grilles/Diffusers with Volume Control Damper

Supply and fixing of Copper Refrigerant piping of 7/8" dia

Supply and Installation of Communication Cable

Supply and Filling of R-22 Refrigerant Gas

Supply, fabrication and fixing of MS Channel for Mounting the Airconditioning Indoor Unit

Supply, fabrication and fixing of MS Channel for Mounting the Airconditioning Outdoor Unit

Towards the Charges for Out of Station & Transportation

GST 18 %