Hindu Religious And Charitable Endowments Joint Commissioner Office Thiruvannamalai Arulmigu Karaikandeswarar Temple Thenmathimangalam Tender

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

a)For foundation and basement

b)Super Structure(Ground floor)

b)Super Structure(First floor)

Brick Work in Cement Mortar 1:5 (one Cement & Five sand) using best quality of country bricks of size 8 3/4"x4 3/8"x 2 3/4" including neat finishing curing etc., complete complying with standard specification and as directed by the departmental officers.

For foundation and basement

Brick Work in Cement Mortar 1:6 (one Cement & Six sand) using best quality of country bricks of size 8 3/4"x4 3/8"x 2 3/4" including neat finishing curing etc., complete complying with standard specification and as directed by the departmental officers.

For Superstructure Ground Floor

For Superstructure First Floor

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For Footing and Grade beam

For Column

For Beams and Slabs

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Supplying and painting the walls with two coats of cement paint over one coat of cement primer with approved primer as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use of work).

Painting two coats of newly plastered wall surface withWater based Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Paving the floor with kota stone slab of size 600 x 600 of 18 / 20mm (polished) in all floors laid in cement mortor 1:3 (one of cement three crushed stone sand), 20mm thick and pointed with colour cement neatly including polishing with polishing stone and oxalic acid etc., so as to perfectly smooth and glossy and including hire charges for polishing machine and including power consumption charges etc.,complete complying with standard specifications and as directed by the departmental officers (The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)

Paving the floor with Pre-polished anti-skid step tiles (Required shape and design) of 20 mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three m sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and fixing mild steel grills for windows, ventilators, rtc., including priming coat etc., complete complying with standard specification.

Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers,transportation charges etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete complying with standard specifications and as directed by the departmental officers.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over with one coat of priming coat with approved primer in all floors etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes 110mm dia having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated Single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point /fan point (for electronic regulator) (5 points / coil) Higher End.

Wiring with 3 x 1.5 sq.mm. (22 / 0.3) PVC insulated Single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with module GI switch box in flush with wall with 6A two way module switch with module front plate with continues earth wire connection and making good of the concealed portion with suitable colour for Concealed PVC pipe stair case Light point Higher End.

Supply and fixing of 4'20W crystal slab LED tube light fittings completed TW round blocks on wall of ceiling with connection with PVC unsheathed copper leads for terminals to the fitting.

Supply and fixing of 1200mm (48") AC ceiling fan high speed complete with 2 module 100W fan step regulator (Higher end) with 600 metre down rod with fan clamp with side plated and cross arm of size 450 mm (18") stepped electronic 300W regulator with required length of down rod on the existing clamp as directed.

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32 mm dia. GI pipe (class B) with 1 no. 32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting. (SD-448)

Supply and fixing of 2nos.6A two module 5 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (SD383)

Supply and fixing of 2 way DP MCB and with in sheet enclosure with 20A DP MCB in flush with wall with earth connection

Supply and fixing of 8 way double pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A 2P MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End. (Lighting) (SD-514)

Supply and run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable coloue (SD337)

Supply and run of 2 of 6 sq.mm (84/0.3) PVC insulated SC unsheathed Copper Conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm PVC insulated SC unsheathed copper wire with painting of suitable colour (SD353)

Supply and fixing of Twenty Compartment metering panel board of made up of 16 SWG MS sheet with powder coated with suitable separator and seal provision for EB with Bus chamber and cable chamber with Busbar of size 1"X1/4" for three phases and neutral,internal connection from busbar to meter by 4 sq.mm copper with suitable copper lugs completely on suitable angle iron frame support (pedastal type) with the (1).12X8" hylem sheet of 6 mm thick (for mounting EB meter and 32A SPMCB switch )-11 nos .(2).32A DPMCB-11 nos. (3) .Neutral link & Earth plate-11 nos

Supply and fixing of 250A TPN Switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only (SD639)heet double break switch with HRC fuse and neutral on suitable angle iron frame work with earth connection only. (SD639)

Supply and Laying of 3 1/2 x 120 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.(SD664)

Supply and clamping of 3 1/2 x120 sq.mm PVC LTUG armoured cable on post or on wall with MS clamps (SD 192)

Supply and fixing of brass cable gland for 3-1/2 x 120 sq.mm. PVC armoured LTUG cable with earth connection (SD169)

Supply and providing cable end termination of 3-1/2 x 120 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete (SD218)

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD211)

Supply and Run of 1 of No.8 SWG copper wire in suittable PVC rigid pipe on wall/floor/ground/Earth connection(SD371)

SUB TOTAL

GST 18 %