Directorate Of Town Panchayats Tender

Plinth Beam

Supply delivery and filling of M - Sand in layer of not more than 15 cm thick including watering with all layers and consolidation complying with standard specification including cost and conveyence of M Sand to Site and all labour charges and all other incidential charges etc,. complete as per Standard Specification

Cement Concrete of mix 1 : 4 : 8 (One Cement four sand eight aggregates) using 40mm gauge hard broken including cost conveyance of all materials to site including formwork and centering labour charges, transporting and placing in position including shoring, strutting, forming protective bunds, cofferdams bailing out of water labour for mixing compacting, finishing and curing, working at depths, tools and plants and incidental charges such as sheeting, shoring and bracing and their subsequent removal etc., complete as per standard specification.

Supplying and filling of well gravel by lorry in basement filling including conveyance loading and unloading charges and all other incidential charges filling laying watering and consolidation etc., complete as directed by the Dept., Officers with standard specification

Supplying , errecting and Centering for Side and Soffiots including necessary supports for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90x60cm & 10 gauge stiffened, welded with steel angle of size 25x25x3mm for boarding laid over silver oak joists (Country wood) of size 10x6.5cm spaced @ about 90cm c/c and supported by casurina props of 10 -13cm dia.spaced @ 75cm c/c etc., complete complying with standard specifications for Pavement Drain etc., Complete.

Without Strutting

Plane Surface

Column

Supplying and Fabrication of Steel and placing in position MS / Ribbed tor steel grills for RCC works as per design given including cost of steel and GI binding wire in Floors etc., Complete complying with standard specification in force per Kilogram.

Reinforced Cement Conrete1 : 11/2 : 3 (Onepart of Cement One and half of sand threepart of aggregates) using 20mm gauge hard Granite broken stone jelly including cost of curing, etc., complete as per standard specification and as directed by Engineer incharge.

Upto Basement

Ground Floor

Brickwork in cement mortor 1 : 5 (One Cement and five Sand) using best quality of country bricks of size 83/4x41/4x23/4 including all cost of materials and Labour Charges including Curing charges etc., Complete as per standard specification.

Below Ground Level

Ground Floor upto 4.50mt

Special Ceiling Plastering in Cement Morter M. 1 : 3 ( One cement, three sand) to 10 mm thick including all cost and conveyance of all materials to site including cost of cement which will be purchared locally by the contractor and conveyance of the same to the actual work site and cost form work including watering curing and all leads of good potable water and all other.

Weathering Coarse with concrete broken brick jelly concrete on 20mm. Gauge in pure slaked shell lime (no sand to be used) over roof slab be proportion of brick jelly to being 32 : 12.5, Well beaten with wooden beaters giving the required shape and thickness as directed by the Departmental Officers.

Finishing the Top with One Course of Machine Pressed Tiles of Size 200 x 200 x20 mm of Approved quality laid in cement mortor 1 : 3 (One part of cement and threepart of sand) mixed with water Proof Compounds 2% by weight of cement used and the top pointed with the same mortar etc., complete.

Supply and fixing of Polished Rajasthan kota stones 20mm thick with machine ctting edges for Flooring inculding laying Vibrating, curing and finishing bearing surface at the sides and bottom of the slan, beams of shall be finished smooth with cm 1:3 and craft paper laid without claiming extra cost complete complying with standard specification and as directed by the departmental officers

Paving the floor with descrgned coloured vitrified tiles of size 600 x 600 x 8mm of best quality and approved variety complying / confirming ISI specification land over cement mortar 1:3 (one cement and three M- Sand) 20mm thick and pomted with same coloured cement neatly etc., complete.

Plastering in Cement Mortar 1 : 5 (one cement and five sand) to 12 mm thick including all cost and conveyance of all materials to site including cost of cement which will be purchared locally by the contractor and conveyance of the same to the actual work site and cost form work including watering curing and all leads of good potable water and all other.

Painting the walls with Two Coats weather Proof Exteriour Emulsion based emulsion Paint over one coat of primer as instructed by the departmrntal officers including Preparation of surface curing, etc complete in all floorscomplying with standard specification. ( The Colour and shade of the paint shall be got approved by the departmental officers.)

Supply and Fixing of Stailess Steel Doors with frame ( Box section using Stailess Steel frame of 1.6mm thick ), of size 100mm x 60mm with a rebate of 30 /35mm x 15mm on one side of the frame including supplying and fixing dovetil splayed Stailess Steel hold fast, cost of material and Labour including all incidental charges etc., complete complying with standard Specifications.

Supply and Fixing of Stailess Steel Doors shutter with frame ( Box section using Stailess Steel frame of 1.6mm thick ), including supplying and fixing locking arrange ments, Ventilating arrangements, cost of material and Labour including all incidental charges etc., complete complying with standard Specifications.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 25GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with spag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown olour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the executive Engineer before use on work

Supplying and Fixing of Push and Pull type Rolling Shutter confirming to IS 6248/1979 and as amended from time to time. With ISI make of approved size and section using 18 gauge G.I.sheet. The Shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc., and as directed by Engineer incharge.

Supplying and fixing in position of Iron grills of required size using 32 x 32 x 6mm angle around and 2 Nos of vertical at center with b flats diagonally to the existing open space for grills into necessary hold fast conveyance and one coat of primer etc., complete for Windows and others.

Painting the new iron works such as steel doors, Windows,Ventilators windows bars,balustrades etc, in all floor with two coats of best approved first quality and colour of synthetic enamel paint of approved quality, colour and brand (to be approved by executive engineer before use on works ) over one the existing red oxide priming coat in all floors excluding cost of priming coat etc, complete complying with Standard Specification. ( The Make, Quality and colour of paint should be got approved by the engineer in charge before use on works ) ( TNSS NO or NBC No 61 V VI (54) 3)

Dadooing sides of walls with Glazed design tiles of size 150 x 150 x 6mm set in Cement Mortar 1:3 ( One cement, three sand) 20mm thick and pointed with the same colour cement including cost and conveyance of all materials, labour charges complete as per standard specification.

Supplying and Fixing in position best approved of BIS quality 110mm P.V.C Rain Water down fall pipe having a pressure of 4Kg / Sq.cm including cost of necessary PVC shoe,PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails etc, and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc, complete. The rate shall be inclusive of cast of removable cast iron grating. The PVc pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.00mt pipe length etc, Complete Complying with Standard Specifications.

Wiring with 2 x 1.5 Sq.mm (22/0.3) PVC insulated SC Unsheathed Cu. Conductor of 1100V grade in cuitable PVC rigid pipe concealed in wall and Ceiling with PVC accessoires in flush with wall with 3mm thick with TW Switch box and 5A F.T. Switch Inflush with wall coverd hylam sheet of 3mm thick with paiting of suitable colour for open P.V.C Light point / Fan Point (for Electronics Regulator) (SD NO: 21)

Wiring with 2 x 1.5 Sq.mm (22/0.3) PVC insulated SC Unsheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and Ceiling with PVC accessoires in Flush with wall 150mm x 100mm x 113mm TW Switch box with 3mm thick Hylum sheet cover for 5A 3 pin non inter locking CS Plug with continuous earth wire connection of 14SWG TC wire and making good of the Concealed portion with suitable colour for CONCEALED PVC PLUG POINT (SD NO: 36)

Supply and run of 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V grade in 25mm dia GI Pipe(Class B) suitably bent at both ends with necessary angle iron upright and end supports for mains mains(SD. NO 69)

Supply and fixing of 16Amps DP switch with metal glad of 500V with fuse and nuetral ( side handle) on suitable TW box PWD earthing (SD. NO 141)

Supply and Fixing of TNEB meter Board suitable for 32A Single Phase Service connection with 32A Fuse unit (500V) 32A neutral link and earth link (1" x 1/8" Copper Flat) on TW Plank of Size 375mm x 300mm x 19mm with Supporting TW Reepers of 1" thick an either side with Painting with Suitable bolt and nuts for fixing the TW Plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB Meter to Fuse Unit (SD No :125)

Paving the floor with design Antiskid ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand) 20mm thick laid in-situ and pointed with same coloured cement etc, complete as per standard specification.

Supply and Fixing in position best quality of approved make Indian Water closet of size 580 x 440 mm with all accessories such as 'P' trap or S trap confirming to IS 2556 part XII with sand cusion and forming flooring alround the closet using 40mm levelling course 1:4:8 100mm thick and finishing the top to the required slope and including necessary internal connection and outlet connection and making the distrubed potion to original condition without leakage etc., including Labour charges for fixing etc.,

Indian Water Closet

Europion Water Closet

Supplying and fixing in position best Indian make Colour glazed earthenware WASH HAND BASIN ( with pedestal)of 550 * 400mm with a pair of C.I. Brackets, including cost of 15mm dia C.P. Pillar tap, 32mm dia B class G.I. Waste with rubber plug and chain, 15mm dia G.M. wheel valve, 15mm brass nipple,15mm dia nylon connection,32mm dia CP brass waste coupling including Fixing of wash basin including CI brackets on to the wall in position with TW plugs and screws rubber washers, white lead and necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti corrosive paint including testing for leakages complete complying with standard specifications and as directed by the Departmental officers. ( The The wash hand basin and Specials should be got approved by the engineer in charge before use on works )

Supply and fixing of LED Bulb Fitting