Bhabha Atomic Research Centre Tender

Providing and painting with Epoxy paint (two or more coats ) using APCODUR-CF-641 finishing coat at all locations prepared and applied as per manufacturer specifications including a priming coat if specified by the manufacturer, preparation of surface and etching with 10% commercial Hydrochloric acid wherever necessary and neutralizing the acid etched areas by washing with 5% solution of soda ash neatly and washing with sufficient water, after first coat Epoxy based trowelling compound if required, including preparation of the surface by scrapping, applying sand paper, filling the holes, joints, cracks if any etc. complete all as per manufacturers technical Data and as directed at site to achieve 200micron Dry film thickness (50 Micron primer coat and 150 Micron finishing Coat).(Contractor has to provide Elcometer sampling sheets etc. at his cost for testing film thickness).

Providing and painting with epoxy paint (two or more coats) using APCODUR-CF-641 finishing coat at all locations prepared and applied as per manufacturer specifications including a priming coat if specified by the manufacturer, preparation of surface and etching with 10% commercial Hydrochloric acid wherever necessary and neutralizing the acid etched areas by washing with 5% solution of soda ash neatly and washing with sufficient water, after first coat Epoxy based trowelling compound if required, including preparation of the surface by scrapping, applying sand paper, filling the holes, joints, cracks if any, et. complete all as per manufacturers Technical Data and as directed at site to achieve 150micron Dry film thickness (50Micron primer coat and 100micron finishing coat). Note:1) 'AMERLOCK 400' Epoxy with 'AMERCOAT 65' Epoxy thinner manufactured by Goodlass Nerolac or 'EPIGIARD TL HIGH BUILD 533 FINISH. Epoxy paint over 'EPIGUARD HP OFF WHITE PRIMER' of 'SHALIMAR PAINTS' make or M/S Asian paints 2) Sample work to be executed and got approved by the engineer in chage before bulk procurement. 3) Sufficient ventilation arrangements to be made in the working area at the coast of contractor. 4) Sufficient lighting / ladders to be provided by the contractor. 5) Equipment/ machinery in the working area to be covered with tarpaulins by the contractor. 6) Sufficient care to be taken while erecting and dismantling of scaffolding/ ladder from damaging / injuring flooring/ wall surfaces. All damages need to be rectified at the contractors cost. 7) Approved type / make of Air Compressor and airless spray gun with tip to be brought by the contractor. 8) Protection wears as per safety code norms are to be provided by the contractor. 9) Paint testing equipments such as 'Ford Cup' 'Elco meter' and wet film gauge are to be arranged by the contractor. 10) Safety qualified supervisor and technical supervisor each 1 No. to be present at site till the completion of the work. (In-Active area)

Providing and painting with epoxy paint (two or more coats) using APCODUR-CF-641 finishing coat at all locations prepared and applied as per manufacturer specifications including a priming coat if specified by the manufacturer, preparation of surface and etching with 10% commercial Hydrochloric acid wherever necessary and neutralizing the acid etched areas by washing with 5% solution of soda ash neatly and washing with sufficient water, after first coat Epoxy based trowelling compound if required, including preparation of the surface by scrapping, applying sand paper, filling the holes, joints, cracks if any, et. complete all as per manufacturers Technical Data and as directed at site to achieve 150micron Dry film thickness (50Micron primer coat and 100micron finishing coat). Note:1) 'AMERLOCK 400' Epoxy with 'AMERCOAT 65' Epoxy thinner manufactured by Goodlass Nerolac or 'EPIGIARD TL HIGH BUILD 533 FINISH. Epoxy paint over 'EPIGUARD HP OFF WHITE PRIMER' of 'SHALIMAR PAINTS' make or M/S Asian paints 2) Sample work to be executed and got approved by the engineer in chage before bulk procurement. 3) Sufficient ventilation arrangements to be made in the working area at the coast of contractor. 4) Sufficient lighting / ladders to be provided by the contractor. 5) Equipment/ machinery in the working area to be covered with tarpaulins by the contractor. 6) Sufficient care to be taken while erecting and dismantling of scaffolding/ ladder from damaging / injuring flooring/ wall surfaces. All damages need to be rectified at the contractors cost. 7) Approved type / make of Air Compressor and airless spray gun with tip to be brought by the contractor. 8) Protection wears as per safety code norms are to be provided by the contractor. 9) Paint testing equipments such as 'Ford Cup' 'Elco meter' and wet film gauge are to be arranged by the contractor. 10) Safety qualified supervisor and technical supervisor each 1 No. to be present at site till the completion of the work. (Active area)