Military Engineer Services Tender
View complete overview of Sikkim MES Tender
Military Engineer Services - MES Tender
Civil And Construction
Civil Works Others
Electrical and Electronics
Solar Installation and Products
Electrical Works
Eprocure
Opening Date25 May 2024
Closing Date21 Jun 2024
Tender Amount₹ 40,00,000
Costs
EMD
₹ 80,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_655821_1Bid Award Id
ViewTender No
8235/A/E8Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
Taking down shutters of any description n. exc 1.00 Sqm each and removing from site complete all as specified and as directed.
10
-
-
S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed.
0.72
-
-
S&F 25 mm thick Flush door shutter, solid core construction, with block board core and plywood face panels. Commercial type on one side and other face covered with decorative face veneer with lipping / frame to match complete all as specified and as directed.
30
-
-
S&F30 mm thick Flush door shutter, solid core construction, with block board core and plywood face panels. Commercial type on one side and other face covered with decorative face veneer with lipping / frame to match complete all as specified and as directed.
10
-
-
M&L for 30mm thick 2nd class hard wood well seasoned glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chmafered or rounded, fitted with cut and mitred beads for securing glass, etc,size of members of shutter as specified in SSR Part I, Section 8, Clause 8.24(a) complete all as specified and as directed.
20
-
-
S&F 100mm long butt hinges, medium weight, cold rolled, mild steel complete all as specified and as directed.
90
-
-
S&F 75mm long butt hinges, medium weight, cold rolled, mild steel complete all as specified and as directed.
30
-
-
S&F 250 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed
30
-
-
S&F 150 mm long aluminium anodised handles, cast type, complete all as specified and as directed.
60
-
-
S&F 100 mm long aluminium anodised handles, cast type, complete all as specified and as directed.
20
-
-
S&F 100mm long aluminum anodised tower bolts of extruded section and fixed complete all as specified and as directed.
80
-
-
S&F mild steel work as in bands, straps, supports or stays for hold fasts, clamps for eaves board / facia , wind ties bend to shape , holes drilled and similar articles conforming to Fe 290 Gde -E-165 including one coat of red oxide primer complete all as specified and as directed.
30
-
-
M&L for plain cement concrete (1:3:6) type C1 (using 20mm graded stone aggregate) as in fixing of hold fast, bed blocks etc including necessary form work as required complete all as specified and as directed.
0.2
-
-
Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed.
10
-
-
S&F in repair 18/19 mm thick particle board, medium density flat pressed, single layer type with BWR type adhesive fixed with screws to timber frame work or in pelmets as in repairs including teak wood lipping of 6mm thick all round fixed with nails complete all as specified and as directed.
10
-
-
Supply and fix continuous (piano) hinges, 30 mm width of flap ( When Open) ,mild steel, bright finish or electro galvanised fixed with stainless steel screws complete all as specified and as directed.
4
-
-
S & F 75mm Hasp and staple, safety type, anodised aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified & as directed.
4
-
-
S & F 40mm dia,brass polished , bright cupboard knobs fixed with nut, screw and washer finished complete all as specified & as directed.
4
-
-
S & F in repair two lever brass locks, cupboard, grade I, size 50 mm complete all as specified and as directed.
1
-
-
Hacking out old broken glass (any thickness , size, quality or description) from metal frame including punching or drilling out old glazing pins/springs clips and removal from the site complete all as specified and as directed by the Engr-in-charge.
15
-
-
S&F 3mm thick sheet glass panes, ordinary quality and glazing with oil putty including steel pin in square n.exc 0.5sq. m in each pane fixed to steel frame complete all as specified & as directed.
15
-
-
S&F in repairs Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified & as directed.
20
-
-
S&F 12mm thick frameless double leaf toughened glass door shutter of approved brand and manufacture , including providing and fixing top & bottom pivot and cover plates with brass pivot and single piece M.S.sheet outer box with slide plate etc.and making necessary holes etc. for fixing required door fittings and lock complete all as specified and as directed.
2
-
-
S& F heavy duty double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing complete all as specified and as directed by the Engr-in-Charge.
2
-
-
M & L for etching to 12 mm thick toughened glass by mechanical /manual means and making aproved design /pattern /logo complete all as specified and as directed.
2
-
-
S&F stainless steel door handles of size 450mm of approved make complete all as specified and as directed.
2
-
-
S & F stainless steel door lock of approved make complete all as specified and as directed.
3
-
-
S & F Floor door stopper with overall length of cover plate 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and asdirected by the Engr-in-Chareg.
40
-
-
S & F Solar control film 25 micron reflectivetype sticked to glass panes (as per instructions of manufactures) complete all as specified and as directed by the Engr-in-Charge.
2
-
-
S & F decorative fascia eaves board of 200mm width under roof made of fiber cement board colour matching/i contrast with the roof complete all as specified and as directed by the Engr - in Charge.
25
-
-
S&F in repair 20mm dia aluminium powder coated fancy curtain rod plain or colour as approved with teak wood finish brackets and knobs complete all as specified and as directed.
25
-
-
S&F of 30mm thick (style thickness) factory made solid panel PVC door shutter consisting of frame made out of mild steel tubes for top and bottom rails, solid steel frame shall be covered with heat moulded single side prelam PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelam PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail on either side & as gap insert for top rail and bottom rail, paneling of both side prelam PVC sheet to be fitted in the mild steel frame welded /sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement as per specification and drawing Complete all as specified and as directed.
15
-
-
S&F of factory made solid PVC door frame of size 50mmx47mm made out of 5mm thick single side prelam PVC sheet reinforced with mild steel square tube and edges will be painted to match with single side prelam sheet as per specification and drawing complete all as specified & as directed.
40
-
-
S & F in repair door closer hydraulically regulated, Aluminium (die cast) body designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified & as directed.
3
-
-
S&F aluminium Powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and as directed.
Note :- Aluminium frame of weight not less than 0.55 Kg/Rm
22
-
-
S & F in repairs 5.5mm thick tinted Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified and as directed.
8
-
-
S & F aluminium Powder coated of any colour (minimum thickness of powder coating 50 micron) door shutters, aluminium section weighing not less than 0.55 kg/ m including necessary jointing cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc.complete all as specified and as directed.
8
-
-
S & F aluminium powder coated of any colour (minimum thickness of powder coating 50 micron) window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified complete all as specified and as directed.
4
-
-
S & F aluminium Powder coated of any colour (minimum thickness of powder coating 50 micron) window and ventilator shutters, side hung type without sash bars, aluminium sections not less than weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified complete all as specified and as directed.
4
-
-
Taking down carefully old aluminum anodised door frame/door shutter fixed type window complete and refixing it after repairing of door frame/door shutter , pintal hinges, incl removing and refixing of door closer incl all hinges and all fittings complete all as specified and as directed.
2.8
-
-
Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and as directed.
2.5
-
-
S & F Mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con-forming to Fe.290.Gde-E-165 complete all as specified & as directed.
20
-
-
S&F for mild steel tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161-1998 grade St-240 including one shop coat of zinc chromate primer paint (including preparation of surface) at contractor's workshop before fabrication and fixing complete all as specified and as directed.
250
-
-
M&L for applying two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide primer to new or previously un-treated steel surfaces of any description over 10 cm in width or girth including preparation of new steel surfaces complete all as specified and as directed.
40
-
-
Taking down cement plaster of any description on brick or stone walls, including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed by the Engr-in-Charge.
40
-
-
Materials & labour for rendering 15 mm thick in cement mortar (1:6) on fair face of brick or stone masonary of wall surfaces finished surface even and smooth without using extra cement complete all as specified and as directed.
40
-
-
Material and labour for applying three coats of white washing including preparation of new / previously untreated surfaces of wall complete all as specified and as directed.
40
-
-
Dismantling old PGI/CGI/Fiber sheeting any gauge, thickness including Nainital. Sikkim or similar pattern roof/facia including ridge etc and keeping serviceable sheets in safe custody for re-use complete all as specified and as directed.
170
-
-
Materials & labour for 0.63mm thick CGI sheeting , ISI marked with 275 per grams Sqm zinc coating with two corrugation side laps fixed with 'L' type or 'J' type or cranked hook bolt and washers in roof covering / walls etc etc complete all as specified & as dirceted.
15
-
-
All as per item No. 52 here-in -before but except sheeting but including new hooks , nuts bolts etc complete all as specified and as directed.
40
-
-
S & F 2.00 mm fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof and wall etc complete all as specified and as directed.
10
-
-
S&F Galvanised 0.63mm thick Plain mild steel sheeting in ridges, hips, valley gutter drip and straight flashing (length and grith as fixed) with grade of zinc coating 275 gm/Sqm as in roof complete all as specified and as directed.
15
-
-
Supply and fix 0.50mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws as in roof complete all as specified and as directed by the Engr-in-Charge.
70
-
-
Supply and fix 0.50mm thick pre-painted galvalume aluminium zinc coating GI based plain steel sheets of any colour having tensile strength of 550 Mpa as in ridges, valley, eaves, etc fixed with self tapping screws complete all as specified and as directed by the Engr-in-Charge.
20
-
-
M&L for preparation of old painted wooden surfaces of any description over 10 cm width or grith and applying one coat of synthetic enamel paint (1st grade quality) complete all as specified and as directed.
35
-
-
M&L preparation of new or previously untreated wooden surfaces of any description exc 10 cm in width and grith and applying two coats of synthetic enamel paint (1st grade quality) over one coat of pink primer complete all as specified & as directed.
100
-
-
Dismantling of wall and ceiling board (fibre pulp, insulation etc.,) /AC sheets and plywood any thickness and cover fillets and removal of dismantled materials/rubbish from site complete all as specified and as directed.
100
-
-
Materials & labour for 4 mm thick plywood, 3 ply, grade BWR, type BB, fixed with screws to timber frame work in wall / ceiling complete all as specified and as directed.
40
-
-
Materials & labour for 6 mm thick plywood, 5 ply, grade BWR, type BB, fixed with screws to timber frame work in wall complete all as specified and as directed.
60
-
-
Materials and labour for 2nd class hard wood plain fillets, square, rectangular or triangular in section, clean swan, secured with nails, cross sectional area exc 03 sq.cm & n.exc 06 sq.cm, complete all as specified and as directed.
60
-
-
S&F powder coated GI grid frame work for false ceiling comprising of the following sections for making partitions of 600mm x 600mm size fixed to walls with rawl plugs & screws and hanged to roof with and including 1mm dia GI wire suspender of suitable length and butterfly clips, size of main tee shall be 23mm x 28mm x 0.30mm thick, cross tee shall be 23mm x 28mm x 0.30mm thick and wall angle shall be 20mm x 20mm x 0.30mm thick complete all as specified and as directed.
30
-
-
Supply and fix 4mm thick Non asbestos fibre cement building boards (E-board) of approved texture, for insulation and acoustic purpose of size 595 x 595 mm size fixed with staples on snap grid as in ceiling with and including dusting of surfaces and applying two coats of oil emulsion diatemper over a coat of primer including preparation of surfaces complete all as specified and as directed by the Engr-in Charge.
30
-
-
S&F Solid PVC single side prelam wall Lining consisting of 5mm thick PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and as directed.
30
-
-
Dismantling timber scantling 40sqcm and over in section any position as in unframed work complete all as specified and as directed.
0.8
-
-
S & F 25 mm thick 2nd class hardwood planed one side for repairs to existing floors with butt joints and fixed with nails and with screws complete all as specified and as directed.
20
-
-
M&L preparation of new or previously untreated wooden surfaces of any description over 10 cm width or grith, filler coat with transparent wood filler liquid and applying two coats of synthetic varnishing complete all as specified & as directed.
20
-
-
M&L for 2nd class hard wood timber scantling fixed clean swan complete all as specified & as directed.
0.6
-
-
All as per item No 70 here-in -before but except timber scantling complete all as specified & as directed.
0.2
-
-
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified & as directed.
150
-
-
Material & labour for non skid coloured ceramic tiles of 7 to 8 mm thick (Square/ rectangular) area of each tile exc 0.18 sqm but not exc 0.38 sqm as in floors etc conforming to IS- 13712, grade B-II - (a) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including cement screed bed / bedding layer of 15mm thick in cement mortar (1:6) complete all as specified and as directed..
10
-
-
Material & labour for non skid coloured ceramic tiles of 7 to 8 mm thick (Square/ rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors etc conforming to IS- 13712, grade B-II - (a) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including cement screed bed / bedding layer of 15mm thick in cement mortar (1:6) complete all as specified and as directed..
38
-
-
Materials & labour for coloured glazed ceramic tiles of size (300 mm x 200 mm / 350 mm x 250 mm / 450mm x 350mm ) x 7 mm thick as in vertical surfaces such as skirting/dado / riser to steps etc conforming to IS - 13712 grade IB-III set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including cement screed bed / backing layer of 10mm thick in cement mortar (1:4) complete all as specified and as directed.
20
-
-
M&L for Vitrified ceramic tiles 10 mm thick (Square / Rectangular) polished, area of each tiles not exceeding 0.36 sqm , as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed/bedding layer in cement mortar (1:6) complete all as specified and directed.
20
-
-
Material and labour for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigments in floors steps etc complete all as specified and as directed.
60
-
-
M&L for 18-20mm thick Granite slab green in one piece machine cut , as in steps , jambs, pillars, window cills, cooking platforms and like bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing including rounding to edges of stone slabs such as in steps , cooking platforms, and other similar situations over and including 20mm thick bedding / backing layer in cement mortar (1:6) complete all as specified and as directed.
2
-
-
Demolition of brick work or stone / boulder masonary or precast concrete block walling , built in cement mortar including all quoins, arches, pillars, etc but exclusing ashlar facings, dressed stoneswork and precast concrete articles complete all as specified and as directed.
14
-
-
M&L for walling of RR stone masonry uncoursed, well bonded, bedded and solidly hearted built in CM (1: 6) including brought upto course at interval of every 60cm including laying PVC pipe in weep holes complete all as specified and as directed.
10
-
-
All as per item No 80.00 here-in -before but except stone complete all as specified & as directed.
4
-
-
Demolition of pre cast cement concrete block masonry or Pre cast concrete article built in cement mortar complete all as specified and as directed.
10
-
-
M&L for pre cast cement concrete block masonry with solid blocks, exc. 10 cm in width and settting in cement mortar (1:6) type C1, (1:3:6) (using 20 mm graded stone aggregate) as per IS 383 complete all as specified and as directed.
10
-
-
Demolition of reinforced cement concrete of any description and in any position such as pre-cast manhole cover or slab etc (reinforcement cut as required to facilitate demolition) complete all as specified and as directed by the Engr-in-Charge.
0.45
-
-
Material & labour for RCC (1:2:4), type B-1 (using 20mm graded stone aggregate) ( nominal mix) as in slab or manhole cover including necessary form work complete all as specified and as directed.
0.45
-
-
Material & labour for use and waste of form work to soffits of suspended slab such as roof slabs, floor slabs, landing and similar works exceeding 200mm thick for flat fair finished surfaces of complete all as specified and as directed.
8
-
-
Material & labour for Mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking , bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips. complete all as specified & as directed.
30
-
-
Material & labour for Mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape required, including cranking , bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified & as directed.
10
-
-
Demolition to cement concrete of any description and in any position not otherwise specifically provided for (unreinforced) complete all as specified and as directed.
5
-
-
Material and labour for PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in surface channels and drains including forming fair finished to drain channel complete all as specified and as directed.
5
-
-
M&L for Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including form, moulds, mitrred/stopped ends complete all as specified and as directed.
20
-
-
Demolition to cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and as directed.
10
-
-
M&L for 75mm thick PCC (1:3:6), type C-2 (using 40 mm graded stone aggregate ) as in plinth protection; path / hardstanding etc laid in bays / panels not exc. 2.00 Sqm each including construction joints at suitable interval and each corner and filled with bituminous mastic filling (1 part bitumen & 3 part sand) and finished the surface even and smooth without using extra cement complete all as specified and as directed
55
-
-
M&L for 75 mm thick PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in sub base of floor complete all as specified and as directed.
100
-
-
M&L for Plain cement concrete (1:3:6) type C2 (using 40 mm graded stone aggregate) as in plum concrete in retaining walls with plums of Stone boulders ( basalt, trap or any other approved) of size 150mm to 300mm complete all as specified and as directed. Note : (i) Volume of stone boulders should not exceed 25% of concrete) (ii) Stone boulders measured and paid separately under other Item
10
-
-
Supply only stone boulders ( basalt, trap or any other approved) exceeding 15cm upto 30cm complete all as specified and as directed.
2.5
-
-
Supply and fix in repair Vitreous China squatting pan of ‘Orissa pattern’, of size 580 mm x 440mm (white) with integral foot rest‘P’ or ‘S’ trap, front or back inlet, any pattern (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe anti syphon pipe etc complete including provision of PCC bedding and connection to trap, and to flushing pipe, antisyphonage pipe, etc. complete including making good to floor complete all as specified and as directed by the Engr-in-Charge.
5
-
-
Taking down eaves gutter and rain water pipes (any size and pattern), including all fittings, heads, shoes, bends, swan necks etc including removal to stores complete all as specified and as directed.
50
-
-
S&F PVC (SWR) pipes, half round 150mm bore with rounded edges including all accessories like bend `T' etc for eaves gutter complete complete all as specified and as directed.
50
-
-
S&F in repair 110mm bore, PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or under floors , fixed on walls with necessary clips complete all as specified and as directed.
30
-
-
Supply and fix in repair 110 mm bore PVC (SWR) bend of any radius for PVC (SWR) pipes, fixed to walls or fixed to steel gutter complete all as specified and as directed.
10
-
-
Supply and fix 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal with acess door complete all as specified and as directed.
10
-
-
Supply and fix 110 mm bore PVC (SWR) vent cowl fixed in position complete all as specified and as directed.
5
-
-
S&F in repairs 75mm bore, PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or under floors including necessary earthwork, fixed on walls complete all as specified and as directed.
15
-
-
Supply and fix in repairs 75 mm bore PVC (SWR) bend of any radius for PVC (SWR) pipes/ Steel Gutters etc , fixed to walls complete all as specified and as directed.
10
-
-
Supply and fix 75 mm bore PVC (SWR) junction Double, (Double T) equal or unequal with acess door complete all as specified and as directed.
10
-
-
Supply and fixing white vitreous china wash down water closet pan (pedestal pattern) EWC, of size 570 x 460 x 380 mm with ‘P’ or `S' trap, including fixing bolts, Plastic water closet seat and cover, closed pattern with flat bottom, and mild steel chromium plated or aluminium anodised hinging device, making all necessary connections and making good the disturbed surfaces of floor complete all as specified and as directed.
10
-
-
Supply and fix in repair 10 litre capacity low level PVC flushing cistern (white), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete all as specified and as directed.
12
-
-
Supply and fix in repair vitreous china, white colour, flat back, wash hand basin of size 55 x 40 x 79cm fixed with brackets , including providing 32 mm dia PVC waste pipe , 32 mm bore CP waste coupling and making all necessary connections complete all as specified and as directed.
6
-
-
Supply and fix PVC connections 15 mm size with PTMT nuts of length 450mm complete all as specified and as directed by the Engr-in-Charge.
26
-
-
Supply & fix bevelled edge looking mirror of size 600mm x 450mm x 5mm thick with selected quality glass, decorative type with aluminium channel frame, mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers including glass self assembly complete all as specified and as directed.
10
-
-
Taking up or down 15mm bore dia steel water tubings including fittings etc including cleaning for re-fixing or removal from site complete and making good disturbed surfaces of walls / ceilings etc complete all as specified and as directed.
100
-
-
Fixing only 15mm bore GI tubing and connection in new or old position (walls, ceiling and floors etc .) including all fittings complete all as specified and as directed.
20
-
-
Supply and fix galvanised steel water tubing 15 mm bore dia, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as directed.
80
-
-
Taking up or down 20mm bore dia steel water tubings including fittings etc including cleaning for re-fixing or removal from site complete and making good disturbed surfaces of walls / ceilings etc complete all as specified and as directed.
50
-
-
Fixing only 20 mm bore GI tubing and connection in new or old position (walls, ceiling and floors etc .) including all fittings complete all as specified and as directed.
10
-
-
Supply and fix galvanised steel water tubing 20 mm bore dia, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as directed.
40
-
-
Supply & fix in repair Bib tap , long body cast copper alloy, chromium plated with crutch or butterfly handle, screwed down for 15mm bore GI Pipe or for brass ferrule including taking down old unserviceable one complete all as specified and as directed.
9
-
-
Supply & fix in repair 15 mm bore dia angular Stop cocks,chromium plated, with wall flange screwed down, screwed fro iron pipe or union and complete all as specified and as directed.
8
-
-
Supply and fixed in repairs 15mm bore pillar taps, fancy type with long neck with aerator cast copper alloy with capstan head, chromium plated, screwed down, high pressure with long screwed shanks, fly-nuts, with screwed for GI pipe complete all as specified and as directed.
9
-
-
Supply and fix Brass chromium plated shower rose 120mm size complete all as specified and as directed by Engr-in-Charge.
5
-
-
Supply & fix in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.
20
-
-
Supply and fix in repairs CP tubular towel rail 600 mm long with and including chromium plated brass screws complete all as specified& as directed.
8
-
-
Supply & fix wall mounted hot and cold water mixer with connecting lugs and wall flanges , cast copper alloy, chromium plated complete all as specified and as directed.
10
-
-
Supply and fix in repair CP corner glass shelf with bracket of size 25 x 25 cm fixed to plugs with brass screws on wall complete all as specified and as directed.
6
-
-
Supply and fix in repairs Steel rolling shutters of laths thickness 1.25mm with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated complete: gear operated type with bevel gear box and crank handle etc complete all as specified and as directed.
2
-
-
Taking down by unfastening all part of steel rolling shutter of any size viz hood cover ,curtain of steel lathe etc and oiling ,greasing the pully , shaft including adjusting the spring ,V -Clamp, bracket plate and manual operated box along with pipe ends arrangement and refing the same in same opening for making operative complete all as specified and as directed.
2
-
-
S&F in repairs stainless steel sink with drainage board made of stainless steel 1.00mm thick for kitchen with plug, washers, waste pipe including cantilever cast iron brackets connecting union of 40 mm CP waste fitting and PVC waste pipe of required length with CP/PTMT fly nuts etc complete overall size 915mm x 460mm with bowl size 410mm x 355mm x 165 mm complete all as specified and as directed.
2
-
-
Material and labour for preparation of old plastered ceiling surfaces, by brooming down or steel wire brushing, scrapping down smoke soot, mould, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash complete all as specified and as directed. by the Engr-in-Charge.
34
-
-
Material and labour for complete removal of existing treatment from plastered or unplastered surfaces of walls including cleaning with scrappers, any number of coats and any width or girth etc and applying two coats of acrylic emulsion distemper over a coat of wall primer over a coat of birla super fine putty finish as required and as per manufacturers instruction complete all as specified and as directed.
25
-
-
Material and labour for applying one coat of acrylic emulsion distemper on old decorated wall surfaces including necessary preparation of surfaces by washing, rubbing down and stopping of existing distempered or painted surfaces complete all as specified & as directed.
25
-
-
Material and labour for applying one coat of exterior acrylic emulsion paint (weather coat) including necessary preparation of surfaces complete all as specified & as directed.
15
-
-
E/M Portion:
Excavation in trenches not exceeding 1.5 M in wide and not exc. 1.5 M in depth for taking out or laying of under ground cable in soft / loose soil complete all as specified and as directed.
135
-
-
Returning, filling in including spreading, levelling, watering and well ramming in layers, not exceeding 25 cm thick in soil complete all as specified and as directed.
130
-
-
Removing surplus soil to a distance not exceeding 50 M and deposited at a level not exceeding 1.5 M above the starting point complete all as specified and as directed.
5
-
-
M&L for cutting the existing road / PCC / drain for taking out / laying of underground cable including necessary earthwork excavation and making good to match with the exisitng surface complete all as specified and with PCC (1:3:6) type C1 by (using 20 mm graded stone aggregate) 100mm thick complete all as specified and as directed.
30
-
-
M&L for 50 mm dia bore galvanised iron light grade for cable protection and sealing both ends including taking out old pipe complete all as specified and as directed.
30
-
-
Taking up/down existing defective cable of sizes 2/4 core 10 to 16 sqmm from the trenches / ducts/ along walls / poles / through poles / under roads/ inside sub station including relaying in same or different position/location complete all as specified and as directed.
1050
-
-
Laying only serviceable cable obtained from taking out in same or new location or position i.e. in trenches/on walls/floord/roof/ceiling etc of size 2/4 core 10 to 16 sqmm including necessary cable lugs, gland etc complete all as specified and as directed.
250
-
-
Supply, laying, jointing and testing XLPE Cable insulated, armoured, earthed, heavy duty electric cable with aluminium conductor , 1100 Volt grade, cross sectional area 10 sqmm 2 core including necessary cable lugs, glands, insulation tape etc complete all as specified and as directed.
600
-
-
Supply, laying, jointing and testing XLPE Cable insulated, armoured, earthed, heavy duty electric cable with aluminium conductor , 1100 Volt grade, cross sectional area 16 sqmm 2 core including necessary cable lugs, glands, insulation tape etc complete all as specified and as directed.
200
-
-
Supply and laying of DWC pipe,ISI marked in trenches or in cable ducts or fixed on walls using clamps along with all accessories like socket,bend,couplers etc confirming to IS 14930,part-II complete with fitting cutting,jointing etc of size 40 mm outer dia complete all as specified and as directed by Engr-in-Charge
750
-
-
M&L straight through joint (Heat Shrinkable) for under ground PVC insulated and PVC sheathed armoured heavy duty XLPE cables with aluminium conductor including jointing kit, including making joints for the cable of size 10/16sqmm x 4 core cables including testing complete all as specified and as directed. Make :-M- seal/Cab seal/3M / Raychem
3
-
-
Repairs to street light fitting any type, solar or conventional type in situ by checking for any loose connections, jointing of wires, replacement of LED drivers and its settings, checking for earth continuity and testing complete all as specified and as directed.
Note-(i) LED drivers measured and paidseperately under respective items
(ii) Ladders scaffolding,safety belts etc required for execation of works shall be arranged by contractor & cost of the same is deemed to be included in the unit rate quoted rates.
(iii) Contractor shall be fully responsible for the safety aspects of the people enagaged by him & any issues(if any) arising during the work shall be dealt by the contractor& the Dept shall be no way responsibile whatsever.
210
-
-
S&F in repair street light bracket fabricated from 40mm dia medium grade GI pipe bent to shape not exceeding 1.5 M long alongwith 2 Nos flat iron clamps of size 25 x 4mm flat iron including nuts, bolts and washers suitable for fixing on poles including applying two coat of synthetic enamel paint over a coat of red oxide primer on steel surfaces complete all as specified and as directed.
Make of GI pipe- Tata/Jindal/Prakash Surya
30
-
-
S&F in repair of clamps suitable for fixing street light on pole fabricated from 32mmx6mm flat iron including nuts, bolts and washers suitable for fixing on poles including applying two coat of synthetic enamel paint over a coat of red oxide primer on steel surfaces complete all as specified and as directed.
10
-
-
S&F in repair of 20 mm dia rigid non metallic PVC Conduit inclusive of all tee, bends,reducers, bell mouth tube ends and fixing accessories such as couplers , lock nuts, saddles, pipe hooks etc complete all as specified and as directed.
380
-
-
S&F in replacement 25 Watt LED decorative post top light fitting of aesthetically designed with symmetrical light distribution spun aluminium landscape luminaire with high power LEDs as light source,Clear cover offers bright illumination for different application IP 65 Rating 240V, 50 HZ, AC supply and with all accessories as required complete all as specified and as directed. Make-Havells cat part No. RUBYPT25WLED757SSYMTOPC/ Crompton cat part No. CBP-610-25-57-SL-CANBK/ Philips cat part No. BGP300 LED28 757 PSU PC IN S1
8
-
-
S&F in replacement post top lantern fitting of 40 Watts LED Stellar LED post-top offering comination of sturdy design,execllent illumination and aesthetics in one go, IP-66 and IK 10rating ensures it stands tall amid varid environemtal conditions with all accessories as required complete all as specified and as directed. Make- Havells cat part No. NEBULAPT40WLED857PSYMTOPC/ Cat No.LPTO-40-CDL-M/ Philips cat part No. BGP300 LED40 757 PSU PC IN S1
8
-
-
S&F in replacement CONE LED BOLLARD of 8 Watts LED imposing street furniture garden light fitting of minimalistic designed acts a silent observer and giving light,diffuser at the upper portion adds functional valve into landscape enviorement, IP-65 with all accessories as required complete all as specified and as directed. Make-Havells cat part No. CONEBLS8WLED857PSYMTPOC/ Crompton cat part No.LBLAL-10-CDL/ Philips cat part No. BCP150 LED150/WW PSU 220-240V 7043
Note- Excavation earth work and PCC also included in quoted rate.
14
-
-
S&F in replacement of 60 Watts,120 lumuns/watt with 10KV SPD LED Street light made up of pressure die cast housing with toughned glass, IP 66 protection and impact resistance of IK07 with secondary optics symmetrical light distribution and with all accessories as required complete all as specified and as directed. Make-Havells cat part No ENDURASUNDOWNSL60WLED765PASYBOTG / Crompton -TRP-409-60-57-SL-GL-NSG /Philps cat part No. BRP056 LED59 CW SLF PSU S1
45
-
-
S&F in replacement of 45 Watts, 120 lumuns/watt with 10KV SPD LED,Street light made up of pressure die cast aluminium housing with high efficiency LED lighting source and lens embeded PC cover , IP66 protection and impact resistance of IK08 with secondary optics symmetrical light distribution all accessories complete all as specified and as directed. Make-Havells cat part No ENDURASUNDOWNSL45WLED765PASYBOPC / Crompton -TRP-409-45-57-SL-GL-NSG/ Philps cat part No. BRP 052 LED 045 CW SLMR FG S1 PSU GR
40
-
-
Supply & fixing in replacement LED Highbay light 80 watt energy saving,enviroment friendly & robust Mediumbay wih high efficiency(110 lm/w),10KV SPD, IP-66 protection with toughened glass complete all as specified and as directed. Make Havells Cat part No.-SAUCERGENXHBP80WLED75760DBOLTG/ Crompton cat part No. LHB11-80-CDL/60M
6
-
-
S&F in replacement 50W LED flood light of die-cast aluminium body, with PC diffused lens enclosure over LED for glare free light IP66 including all accessories as required complete all as specified and as directed .
Make- Havells Cat Part No. JETAADORNFLS050WLED757PR1SYMTOTG/ Crompton cat part No. CFS-504-50-5760D-SLGL-NSG/ Philips cat part No. BVP180 LED50 CW PC WB 50W 120-270 PSU
2
-
-
S&F in replacement 80W LED flood light of die-cast aluminium body, IP66 including all accessories as required complete all as specified and as directed.
Make- Havells Cat part No. JETALEGANZAFLS80WLED757P60DTOTG/ Crompton cat part No.TFS-504-80-57-60D-SL-GL-NSG/ Philips cat Part No. VP192 LED82 CW HO NB FG GR PSU
2
-
-
S&F in replacement 100W LED flood light of die-cast aluminium body, IP66 including all accessories as required complete all as specified and as directed.
Make- Make- Havells Cat part No. JETALEGANZAFLS100WLED757P60DTOTG / Crompton cat part No. -TFS-504-100-30-60D-SL-GL-NBK/ Phiips cat part No. BY225P LED100S CW NB PSU FG GR V1
2
-
-
S&F in replacement 150W LED flood light of die-cast aluminium body, IP66 including all accessories as required complete all as specified and as directed .
Make- Havells Cat part No. JETALEGANZAFLS150WLED757P60DTOTG/ Crompton cat part No.LFLN-150-CDL/60-M/ Philips cat part No. Type HSN Code MRP (INR) BVP183 LED156 CW FG SYWB 150W PSU
2
-
-
S&F in replacement of 250 W LED flood light of die-cast aluminium body, IP66 protection, heat resistant toughened clear glass cover with reflector and all accessories complete with all accessories as required complete all as specified and as directed.
Make- Havells Cat part No. JETAIRISALPHAFL250WLED757APLTG/ Crompton cat part No. CFS-506-250-57-60D-SL-GL-NSG/ Philips cat Part No.BVP483 LED235 CW SMB PSU GR
2
-
-
S&F of street light terminal boxes made out with SMC material, shock & dust proof of inside size 300x200x105mm as per IS and including 20 Amp, TPN busbar fixed on insulators, 01 No 10Amp, SP MCB, earth termination with nuts & bolts and including 02 sets of flat iron 25x6mm clamps of suitable size with nuts, bolts and washers including two coats of aluminium paint over a coat of primer on exposed steel surfaces complete all as specified and as directed. Sintex cat Part No. GSJB-3020, or equivalent Hansel
60
-
-
S&F in replacement of of 1.5 sqmm 3 core PVC insulated flexible copper conductor wire from street light to terminal box drawn through MS pipe/PVC conduit or as indicated in other locations complete all as specified and as directed.
600
-
-
S&F in repair 15 W LED bulb complete all as specified and as directed. Make :- Crompton Greaves /Havells /Philips
20
-
-
Supply only electronic driver suitable for LED street light fittings of capacity 45 Watt complete all as specified and as directed.
35
-
-
Supply only electronic driver suitable for LED street light fittings of capacity 60 Watt complete all as specified and as directed.
25
-
-
M&L plain cement concerete (1:4:8), type D-2 (using 40mm graded stone aggreegates) as in foundation/Copping filling and mass concrete for pole etc complete all as specified and as directed.
4
-
-
M&L repairing and greasing of motors, harnessing wires of 16 M for high mast light poles at site including taking down light and others accessories complete all as specified and as directed.
1
-
-
M& L for photo sensor for opearation 230 volt, with 1 NO/NC, holder clamp,polycaronate covers, M.S base clamp of the street light contactor complete all as specified and as directed.
2
-
-
Supply and fixing MCB, SP 6 TO 32 Amps amps amp rating 240V, 10KA 'C' curve complete with connection testing and commissioning complete all as specified and as directed.
20
-
-
Supply and installation 24 watt solar all-in-one street lighting with high efficiency Mono Crystalline Solar PV Module,Lithium Ferro Phosphate battery with in built BMS techonology, High efficiency LED, MPPT solar charge controller and Aluminium Extruded body & is specially programmed to automatically controlled the dimming and brightness of light,which increase the backup time in existing pole complete all as specified and as directed with following specification.
(i) Solar panel 60W
(ii) LED power 24 W
(iii) Battery capacity 30Ah
(iv) lumens(lm)3120 lm
(v) LED life time- 50000h
(vi) Viewing angle -120 degree
(vii) Charging time- 1 day
(viii) Autonomy- 2 days
(ix) CCT(K) -5700K
(x) working Temp- -10 degree to 50 degree
(xi) Min weight -18.5 Kg
2
-
-
M& L for preparation of old painted surfaaces of street light steel tubular poles above GL/Copping including cross section channels,flat iron clamps by srapping with wire brush applying one coats of aluminium paint including pole numbering using three layer of radium strip of min 4-5 inch wide(Yellow,Green,Blue) on each pole using printer letter all as specified and as directed.
Note-:(i) Ladders scaffolding,safety belts etc required for execation of works shall be arranged by contractor & cost of the same is deemed to be included in the unit rate quoted rates.
(ii) Contractor shall be fully responsible for the safety aspects of the people enagaged by him & any issues(if any) arising during the work shall be dealt by the contractor& the Dept shall be no way responsibile whatever.
195
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements