Urban Improvement Trust Tender

Survey work of roads including ploting of L-section, X-Section @ 25m c/c interval showing existing Ground level line, proposed level line in different colour with clour back ground of graph sheet of 1 mm square size showing all the required details as per IRC : SP-20 and IRC-19 Pliting work shall include plan of the road showing required curve details width of existing road, if any and proposed road. toe line, width of revenue track. proposed location of borrow area width making of cattle crossing location, Lay bye and Bus locations, ramp locations, permanent structure / Electric pole / Telephone / Tree etc. (Print of L- Section sheet shall be for 1 Km. )On CD work location, survey work required on 0.5 Km. on either side of CD works and L-section ahall be proposed on separate A-4 size sheet for eatch CD works and same shall be superimposed on X-section showing proposed CD work in different colour line and details of slope of CD work etc.E/W calculation of road work shall including ploting of X-section Max 2 Nos on A-4 size sheet showing line of subgrade and embankment with E/W Calcution sheet showing quantum of E/W involyed in sub grade in embankment E/W in cutting and Qty of E/W cutting adjusted in filling within 100 m lead.Based on PWD Road BSR 2016, Ref.16.7.27

Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with a lift upto 1.5 m and lead upto 1000 m as per MoRTH Specification Clause 301.3Based on PWD Road BSR 2016, Ref. 3.5(iii)

Stripping of top soil from borrow areas located in agriculture fields, storing at a suitable place, spreading and relaying after taking the borrow earth to maintain fertility of the agricultural field, finishing it to the required levels to the satisfaction of the farmer/land owner as per MoRTH Specification Clause 301.3.2.& 305.3.3. Based on PWD Road BSR 2016, Ref. 3.11

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300-1 and 300-2 with a lead upto 1000 m as per MoRTH Specification Clause 305.3 Based on PWD Road BSR 2016, Bulding BSR 2013, Ref. 3.4(i)

Construction of embankment with approved materials deposited at site obtained from roadway cutting and excavation from drain and foundation or other structures graded and compacted to meet requirement of Tables 300-1 and 300-2 as per MoRTH Specification Clause 305.3 Based on PWD Road BSR 2016, Ref. 3.3

add extra for lead upto 500 mtr for earth, sand, line, morrum, manure or sludge etc. including loading and unloading and all lifts. Based on PWD Bulding BSR 2013 Ref. 5.1

Construction of granular sub-base by providing well graded material, spreading in uniform layers with Tractor Mount Grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per MoRTH Specification Clause 401. For Grading II Material. Based on PWD Road BSR 2016, Ref. 4.1(A)(ii)

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400-12 & 400-13 and MoRTH Specification Clause 406. By Mechanical Means with all leads. Based on PWD Road BSR 2016, Ref. 4.5

Providing and applying primer coat with Bitumen emulsion (SS-1) on prepared surface of granular base (Stablised soil baes/Crusher Run Macadam) including cleaning of road surface and spraying primer at the rate of 0.90- 1.2 kg/sqm using mechanical means as per MoRTH Specification Clause 502. Medium porosity. Based on PWD Road BSR 2016, Ref. 5.1(ii)

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per MoRTH Specification Clause 503.Based on PWD Road BSR 2016, Ref. 5.2(ii)

Providing and laying bituminous macadam with hot mix plant using crushed aggregates of grading as per Table 500-7 premixed with bituminous binder, transported to site with all leads laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per MoRTH Specification Clause 504.Based on PWD Road BSR 2016, Ref. 5.3

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per MoRTH Specification Clause 510. by mechanical means. bitumen(S-65)Based on PWD Road BSR 2016, Ref. 5.9 Case II(ii)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per MoRTH Specification Clause 511, , by mechanical means, type -C Bitumen (S-65),Based on PWD Road BSR 2016, Ref. 5.12(B) Case(III)(II)

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and MoRTH specifications Clause 1702, 1703, 2102 & 2104 P.C.C grade M 10,Nominal mix 1:3:6,Based on PWD Road BSR 2016, Ref. 11.4(I)(i)

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 602.2.2 M-30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation with vacuum dewatering and floater including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days,using curing compound and water finishing to lines and grade as per drawing and MoRTH Specification Clause 602 including vaccum dewatering process with all required equipments. Based on PWD Road BSR 2016, Ref. 6.1

Centering & shuttering with plywood or steel sheets including struting proping bracing bothways & removal of form work for foundation in basement rafts, footing straps beams , bases of columns etc upto plinth level. Based on PWD Bulding BSR 2013, Ref. 4.11

Marking Centre Line and stop lines etc. on road as IRC pattern with thermoplastic paint of approved quality and make with 8% glass beads laid on the road surface at temperature 1600C with a special applicator machine complete with a special applicator with labour, material and traffic diversion arrangements. Based on PWD Road BSR 2016, Ref. 16.7.5

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 801.3.1 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and MoRTH Specification Clause 801. 600 mm circular Based on PWD Road BSR 2016, BSR Ref. 10.2(A)(1)(iii)

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 801.3.1 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and MoRTH Specification Clause 801. 600 mm x 450 mm rectangular Based on PWD Road BSR 2016, Ref. 10.2(A)(1)(v)

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 801.3.1 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and MoRTH Specification Clause 801,600 mm x 600 mm square,Based on PWD Road BSR 2016, Ref. 10.2(A)(1)(vi)

Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 801.3.1. fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approved drawing and MoRTH Specification Clause 801. Direction and Place Identification signs upto 0.9 sqm size board. Based on PWD Road BSR 2016, Ref. 10.3(A)(i)

Supplying of Cat's Eye made of aluminium alloy size 75x100x22 mm haing 21 biconvex lenses embedded in circular disk of ABS plastic on each side. Based on PWD Road BSR 2016, Ref. 16.6.8

Earthwork in excavation for structures as per drawing and MoRTH specifications Clause 304.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.Ordinary soil,Upto 3 m depth in all respect. Based on PWD Road BSR 2016, Ref. 11.1(I)(i)

Providing and Laying Reinforced Cement Concrete Pipe NP4 as per design in Single Row ,Providing and laying reinforced cement concrete pipe NP4 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 2905.300 mm dia. Based on PWD Road BSR 2016, Ref. 9.4(E)

Stone masonry work in cement mortar in foundation complete as per drawing and MoRTH specifications Clauses 1402, 1405, 2102 & 2104.Random Rubble Masonry.In cement mortar 1:4. Based on PWD Road BSR 2016, Ref. 11.6(III)(ii)

Providing PCC M-20 architectural coping on the top of wing wall, return wall etc. complete as per drawing and MoRTH specification Clauses 1313, 1411 and 2206.6, 75 mm thick.Based on PWD Road BSR 2016, Ref. 12.14 (A)

Pointing with cement mortar (1:3) on Stone work as per drawing and MoRTH specification Clauses 1406 and 2200 Based on PWD Road BSR 2016, Ref. 13.18