Rajcomp Info Services Limited Tender

Supply & Installation of chair with headrest for 1 Person SEAT/BACK ASSEMBLY: The Cushioned seat assembly consshould be ts of seat outer (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The Net Back should be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric with high tenacity yarn.Full Back Size: 46.5 cm. (W) x 60.0 cm. (H) Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgf for 25% compression. BACK SPINE: The support spine should be made up of High Pressure Die cast polished hed Aluminum. ARMRESTS : The armrest should be having two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should be provided in Aluminum structure of armrest which should be connected to Aluminum Back spine and should be operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner.ACTIVE BIO-SYNCHRO mechanism: The adjustable tilting mechanism should be designed with the following features: • 360° revolving type • Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort • Tilt tension adjustment can be operated in seating position • 5 position Tilt limiter giving option of variable tilt angle to the chair • Seat / back tilting ratio of 1:2 • The mechanism housing should be made up of HPDC Aluminum & black powder coated (DFT 40 to 60 micron)SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 3.75±0.1 cmLUMBAR SUPPORT ASSEMBLY: The Lumbar support assembly should consist of lumbar spine (material-Glass Fiber Filled Nylon) which should be fixed to Aluminum Back spine. The Lumbar pad (material- Poly Propylene) should be fixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustment of 5.0±0.5cm PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm. PEDESTAL ASSEMBLY WITH CASTORS:The pedestal should be High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter..The neckrest assembly consshould be ts of upholstered Neckrest inner(material-PolyPropylene) with moulded Polyurethane foam and Polyster fabric.Upholstered inner should be fixed to Neckrest cover.Neckrest should be fixed to Back assembly through Neckrest spine .Neckrest assembly has height adjustment of 5.5 +/- 0.5cm and Rotation adjustment of overall 20° +/- 2°   as per sketch/drawing matching with Photographs as attached in RFP BOQ

Supply & Installation of Chair without headrest SEAT/BACK ASSEMBLY: The Cushioned seat assembly consshould be ts of seat outer (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The Net Back should be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric with high tenacity yarn. Full Back Size: 46.5 cm. (W) x 60.0 cm. (H) Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgf for 25% compression. BACK SPINE: The support spine should be made up of High Pressure Die cast polished hed Aluminum. ARMRESTS : The armrest should be having two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should be provided in Aluminum structure of armrest which should be connected to Aluminum Back spine and should be operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner. ACTIVE BIO-SYNCHRO mechanism: The adjustable tilting mechanism should be designed with the following features: • 360° revolving type • Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort • Tilt tension adjustment can be operated in seating position • 5 position Tilt limiter giving option of variable tilt angle to the chair • Seat / back tilting ratio of 1:2 • The mechanism housing should be made up of HPDC Aluminum & black powder coated (DFT 40 to 60 micron) SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 3.75±0.1 cm LUMBAR SUPPORT ASSEMBLY: The Lumbar support assembly should consist of lumbar spine (material-Glass Fiber Filled Nylon) which should be fixed to Aluminum Back spine. The Lumbar pad (material- Poly Propylene) should be fixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustmentof 5.0±0.5cmPNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm.PEDESTAL ASSEMBLY WITH CASTORS:The pedestal should be High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.)TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter.as per sketch/drawing matching with Photographs as attached in RFP BOQ

Supply & Installation of Reception Counter Top shall be of Rubberwood with clean Matt PU finish 18 mm thick , inside radius - 700 mm , outside radius - 1350 mm and depth - 650 mm . Cork shall be 18 mm thick of rubber . Glass shall be Frostered 10 mm thick diamond cut finishing on edges , inside radius shall be - 1202.5 mm , otside radius - 1402.5 mm and depth - 200 mm . The Modesty Panel shall be MS Perforated sheet below worksurface : 0.8 mm (thick) x 665 mm ( height) x 1345 mm (flat length ) . Above Worksurface : 0.8 mm (thick ) x 260 mm (height) x 1345 mm (flat length) . The legs shall be of MS tube 1.6 mm thick diameter 50.8 mm and height 604 mm Provision for 3 no. 5/15 AMP Switch/Sockets along with 1 no. LAN Sockets should also be there. as per sketch/drawing matching with Photographs as attached in RFP BOQ

Supply & Installation of Collaborative Seating Stools Drift’s flat top and round edge supports freedom of movement • Its wooden base should be attached with castors and can be moved around in all directions with ease Width-445 Depth-445 Height -575 It should be covered with fabric as per approval of Engineer in charge as per sketch/drawing matching with Photographs as attached in RFP BOQ

Supply & Installation of Conference Table 1. Furniture Top:- The material of working surface shall be made of alumina tri-hydrate and acrylic resin material supported on minimum 12 mm thick MDF base with molded Polyurethane edge. The top finish shall be fire retardant, water, resistant and scratch resistant and shall have high hardness. induction charging shall be provided on furniture top for FSC every user. 2. The manufacture shall be FSC certified. 3. the under structure shall be made up of 18 mm thick MDF board with 2 mm thick PVC edge banding tape. 4. Accessories: Flap 5. Cable Trays and Wiring:- The furniture must be designed with cable trays to alllow for continuous & concealed cable management across the furniture. Approximate Minimum Dimensions of Table - 5000(W) X 2500 (D) X 750 (H) Provision for 3 set of 3 no. 5/15 AMP Switch/Sockets along with 1 no. LAN Sockets should also be there including supply & provision of connector for Laptop connectivity. The breakup of 2500mm is : 600mm table width + 1300mm gap + 600mm table width as per sketch/drawing matching with Photographs as attached in RFP BOQ

Supply & Installation of Manager Table 1800x2100x750 Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension should be 325 MM. Drawers should have a soft closing & anti slam mechanism. Handles should be provided for ease of opening. Pedestals should be provided with lock for security. Provision for 3 set of 5/15 AMP Switch/Sockets along with 1 no. LAN Sockets should also be there including supply & provision of connector for Laptop connectivity. as per sketch/drawing matching with Photographs as attached in RFP BOQ

Supply & Installation of Table Work Surface: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Soft closing access flap provided for access to power supply and audio cables.Work top is available in two shapes Square and Pebble (Round).Side Panel:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990 matching to the Worktop, Edge banded with matching 2 mm thick PVC lipping. Cutout with Gromet provided for routing cables in case any Audio Visual equipment is to be fixed later.Understructure:The Under-structure consists of an Inner Tube Assembly with Top for Worktop Mounting and Base plate with levellers. The Top Plate is made of 5mm thk hot rolled steelPlates (HR) (As per IS: 2062) & the bottom plate is made of 8mm thk hot rolled steel Plates (HR) (As per IS:2062). The Inner Tube Assembly is made of 25.4mmx 25.4mm x 1.2mm thk round electric resistant welded tube (ERW)(As per IS:7138) welded together using Tungsten inert gas welding. The whole structure is epoxy polyester powder coated (DFT 40-60 microns). table top should be 1mtr by 1mtr. as per sketch/drawing matching with Photographs as attached in RFP BOQ

Supply & Installation of Center unit for Sofa Overall Size : Width : 118cm Depth : 60cm Height : 45cmTABLE METERIALS & SIZE :TOP:Sheesham 18 mm LEGS: 80X80 Top Side 40X40 Bottom Side Support 45x25mm & 8 Pcs Bolt & Nut Length : 1.1 mtr. as per sketch/drawing matching with Photographs as attached in RFP BOQ