Public Works Department Tender

Demolishing brick work including stacking of serviceable material and disposal of unserviceable material within 50 meters lead. In Cement mortar.

Dismantling stone rubble masonry including stacking of serviceable material and disposal of unserviceable material within 50 meters lead. In Cement mortar.

Grading roof water proofing treatment with : Cement concrete 1:2:4 (1-Cement:2-coarse sand :4-graded stone aggregate 20mm nominal size).with water proofing compound with manufactures specification

Providing and fixing Tiles over Roof fixed in 25 mm thick cement mortar 1:4 bed complete 20 mm thick plain cc roofing tiles

Providing batta (gola) 75mm x 75mm in cement concrete (1:2:4) including finished with cement mortar 1:3 as per standard design.

Providing and laying in position cement concrete including curing compaction etc. of specified grade excluding the cost of centering and shuttering =All up to plinth level M10 grade Nominal Mix ( with graded stone aggregate 20mm nominal size)

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete above plinth level up to 4.5Mtr. height. Hot finished welded type tubes

Providing corrugated G.I. Sheet roofing fixed with G.I. J or L hooks bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coat of approved paint on over lapping of sheet complete (upto a pitch of 600) & excluding the cost of purlins rafters and truses, for class of sheet : 1.25 mm thick. Add extra over item No. 10.21 for providing and fixing CGI sheets in curved roofing

Plaster on new surface on wall in cement sand mortar 1:3 including raking of joints etc. complete fine finish : 25 mm thick.

6mm cement plaster to ceiling of mix 1:3 (1 Cement : 3 fine sand)

Brick masonry in super structure upto third storey with bricks of class designation 75 in :Cement mortar 1 : 4 (1 cement : 4 coarse sand)

Half brick masonry in super structure upto third story using bricks of designation 75 with nominal hoop rainforsed (2 Nos. 6mm MS bar) at every fourth course in for hoop rainforcement Cement mortar 1 : 6 (1 cement : 6 coarse sand)

Providing and fixing Ist quality standard White Ivory Glazed Tiles ISI marked [IS:13753] of size 300mm x 200mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster). Size 300x450,300x600(as per direction of engineer in charge)

Providing and fixing Ist quality MAT finished ceremic tile size 300x300mm confirming to IS : 13753 colour such as white, grey, ivory, fume red brown in walls, floors, steps, pillars etc. laid on a bed of neat cement slsurry including nicely finished joints using water proof joint filler power (Untile or Roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster).

Centering and shuttering with plywood or steel sheets including strutting, propping, bracing both ways with wooden members and removal of formwork for superstructure up to 4.5 mtr above plinth, for: Columns, pillars, posts and struts etc.

Centering and shuttering with plywood or steel sheets including strutting, propping, bracing both ways with wooden members and removal of formwork for superstructure up to 4.5 mtr above plinth, for: Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands , coping, bed plates, anchor blocks, sills, chhajjas lintel, beam etc.

Providing and layin in position specified grade of cement concrete for RCC Structure elements unto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement ; 3 coarse sand) and making good the joints excluding the cost of centering shuttering and reinforcement forshuttering and reinforcement : beams suspended floors roofs griders having slopes up to 15 digree C, landings balconies shelves chajjas lintels bands plain window sills staircases and spiral staircases M20 grade nominal mix (with graded stone aggregate 20mm nominal size)

Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. Tremo Mechanically treated bars

Providing and fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joint mitred welded and grinded including hold fast of steel lugs 13mm x 3mm and 15 Cm. long embedded in C.C. block 15x10x10 Cm. of 1:3:6 nominal concrete and including fixing of pivoted hinges of superior quality, window shutters made out of 55x20mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitred and grinded including 10mm x 10mm square bars welded to frame for paitam fixing float glass 4 mm thick panes with glazing clips and metal sash putty and fixing of shutters frames peg stay, U shape handle 100 mm long, tower bolts 100 mm long of steel power coated superior quality including fixing and jointing with frame hinges priming coat with steel primer complete in all respect as per direction of Engineer-in-charge. Window openable.

Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance.

Providing and fixing Square bars or other flat welded to window, ventilators etc.

Supply & fixing steel shutter (Almirah type) with 18 gauge steel border & steel shutter including locking arrangement and painting etc. complete fixed on wall with joint fast (iron clip)

Supplying and fixing in walls machine cut and polished stone shelves, tands and sills in CM 1:3 with machine cut edges :Kota stone 25 to 30mm thick.

P & F Marble Urinal Partition slab both sides polished of approved design cut from marble size 900x600mm. Makrana 'Adanga' or Raj Nagar ISt Quality White or Andhi Indi-Italian marble.

Labour charges for removing WC Pan (any type) of all sizes with care incl. all necessary fittings P or S trap

Labour charges for removing and refixing of urinals (all type & size) incl. all necessary fittigns

Labour charges for repair to door / window without using any material such as applying randha (finishing) tightening of bolts & screw etc.

Repair to stone masonary in cement sand mortar 1:6 with old and new stone.

35 mm thick Rough Chiesel dressed stone flooring of approves shade set in pattern over 20mm thick base of cement mortar 1:6 (1-Cement:6-coarse sand) and jointed with cement sand mortar 1:3 complete in all respects : Kota Stone.

Polished Blue Kota Stone flooring skirting, laid over 20 mm thick base of C.M. 1:4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete : For area of each slab up to 2001 to 5000 Sq. Cm : (A) 25 mm thick slab.

Providing and fixing in cement sand mortar 1:4 single paitam (rebated) stone doors windows and ventilator frames of approved quarry : Size 100x75mm.

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete :25 mm.

Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the granite slab complete including rubbing and polishing of : Green / Black / Other granite 1501 Cm2 to 3600 Cm2 Tiles Green / Black / Other granite Above 3601 Cm2 Slabs

Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal, dehydreresin in glue both sides with approved steel fittings complete as per Annexure ‘A’ Commercial Veneer both side 25 mm thick shutter Add extra for Sunmica 0.8 mm thick

Renewing glass panes, with puty and nails wherever necessary: 4 mm thick plain glass panes.

Filling of sunk portion of roof with earthen pots of required height including filling voids with 1:2:4 light concrete, using brick bats complete leveling and dressing the surface by 50mm thick cement concrete 1:2:4 as per specification.

Providing and Fixing at all height all false ceiling of 12.5 mm thick tapered edge Gypsum board conforming to IS : 2095 including providing and fixing of frame work made of special section power pressed from M.S. sheet and galvanized in accordance with zine coating 600 as per IS : 277 and consisting of angle cleats of thick 25 mm wide x 16 mm thick with flanges of 22 mm and 37 mm at 1200 mm center to center one flange fixed to the ceiling with dash fastner 12.5 mm dia x 40 mm long with 6 mm dia bolts to the hangers of 25x25x5mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45 mm x 15 mm x 0.9 mm running at the rate of 1200 mm center to center to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450 mm center to center shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm dia x 230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall / partition with the help of rawl plugs at 450 mm center to center with 25 mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of gypsum board with recommended filler paper tapes, finisher and two coats of primer suitable for gypsum board as per manufactures specifications and also including the cost of making openings for right fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specifications and direction of the Engineer-in-charge but the excluding the cost of painting.

Repair to cement plaster in cement mortar 1:6 (1-Cement:6-fine sand) including removal of old plaster in regular shape and white or colour washing.

Applying white cement based putty over cement plaster surface for making even surface.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: New work (two or more coats) over and including scrapping and priming coat with cement primer.

Finishing wall with water proofing cement paint of approved brand and manufacture and or required shade to give an even shade including all scaffolding: Old work (One or more coats).

Painting with enamel paint of approved brand and manufacture to give an even shade: One or more coats on old work.

Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect. Old Work

Providing & fixing anodizing alumium work (Anodizing to be got done from approved Anodizer) for doors, windows, ventilators and partition with extruded built up standard tubular and other sections of approved make confirming to IS : 733 and IS : 1285 anodised transparent 81 dyed to required shade according to IS : 1868 (Minimum anodic coating of grade AC 15), fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gas at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required inlcuding cleat angle Aluminum snap beading for glazing/paneling, C.P. Brass/ Stainless Steel screws, Al. Tower bolt & Al. handle & Al. Aldrop etc. all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and peneling to be paid for separately). For shutters of doors, windows & ventilators incl. providing and fixing hinges/ rollers etc. and making provision for fixing of fittings wherever reqd. (lockes shall be paid for separately).

Providing and Fixing 12mm thick prelaminated three layer medium density (exterior grade) particle bonded formaldehyde synthetic resin of approved brand and manufacture in paneling fixed in aluminium doors, windows/ stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. (Internal work Exposed on wall) a) 20 mm nominal outer dia pipes

b) 32 mm nominal outer dia pipes

P & F Indian type white glazed vitreous china Ist quality W.C. orissa pan (IS:2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor : Size 580x440 mm.

P & F European type white glazed vitreous china Ist quality W.C. (IS:2556 Mark) including cutting and making good the wall and floor.Wall Mounting (syphonic)

P & F water closet Seat Covers with brass hinges complete IS 2548-1996 : Solid PVC (ISI marked) grade-I White for EWC.

P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make 25 mm G.I. waste pipe complete including cutting & making good the wall : Size 550 mm x 400 mm dia for counter top.

P&F Grating of approved quality/ make C.P. brass with frame (Heavy) & superior quality size 125mm dia.

P & F PVC Storage Tank (IS:12701 marked indicating the BIS license No.) of approved make with cover, 25 mm dia 1 M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc. complete of approved design. 500 litres capacity.

P&F Jet spray for water closet with C.P. copper tube flange of approved make

P & F Low level Flushing Cistern of 10 litres capacity (IS:2556 mark) of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS:1703 mark) complete including cutting and making good the wall : PVC with PVC bend as per IS : 7231

Providing and fixing Sperior quality ( Jaquar Continental/ Clarion) CP Brass fittings Complete as per direction of Engineer Incharge a) Bib Cock with long thread 15 mm nominal size

c) Angular stop cock with long thread 15 mm nominal size

d) Swan neck pillar cock 15 mm nominal size

P&F rigid PVC Pipe (IS:4985 mark) class II(4 Kg. /Cm.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant a) 110mm dia

P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: a) Door Tee 110mm dia

b) Bend 87.5 110mm dia

c) Vent Cowel 110mm dia

d) Pipe clip 110mm dia

Providing and fiixng C.P. flange for 15mm dia taps