Public Works Department Tender

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding:Two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect.(Old Work)

Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an evenshade with two or more coats including prepartion of basewith sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision .

Painting with enamel paint of approved brand and manufacture to give an even shade: One or more coats on old work.

Providing and laying in position cement concrete including curing compaction etc. of specified grade excluding the cost of centering and shuttering =All up to plinth leve 1:2:4 (1Cement :2 Course Sand 4 Graded stone aggregate 20 mm nominal size

Brick masonary with mechanised autoclaved flyash lime brick conforming to 12894 ; 2002 of class desigation 100 in foundation and plinth mm in :( Used Banas/ Bikaner sand ) ,1:4 Mortar

Providing & fixing steel glazed doors,windows and ventilators shutters of standredrolled steel section joint mitred and weldedwith steel 13x3mm lugs 10 Cm. longembedded in cement concrete blocks15x10x10 Cm. of 1:3:6 (1-Cement:3-coarsesand:6-graded stone aggregate 20 mmnominal size) or with wooden plugs andscrews or rawl plugs and screws or withfixing clips or with bolts and nuts asrequired, including providing and fixing ofplain glass panes 4mm thick with copperglazing clips and special metal-sash putty ofapproved make, or metal beading withscrewscomplete including priming coat of approvedsteel primer,excluding the cost of metalbeading and other fittings except necessaryhinges of pivots steel handles and peg stayetc. as required.

Providing and fixing welded mesh/expanded metal mesh in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. complete (excluding frame work) of size

Providing and fixing factory made P.V.C. door frame of size50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S.square tube, the vertical door profiles to be reinforced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and directionof Engineer-in-Charge.

Providing and fixing to existing door frames. 16.20.1 30mm thick factory made solid panel PVC door shutterconsisting of frame made out of M.S. tubes of 19 gaugethickness and size of 19mm x 19mm for stiles and 15 mmx15mm , top & bottom rails. M.S .frame shall have a coat ofsteel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC „C channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on either side forming stiles; and 5mm thick, 95mm wide PVC sheet out ofwhich 75 mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and115mm wide PVC sheet out of which 75 mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top bottom and lock rails shall be provided either side of the panel. 10mm (5mm x 2) thick, 20mm wide cross PVC sheet shall beprovided as gap insert for top rail & bottom rail. Panelling of5mm thick PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with 7mm (5mm +2mm) thick x15mm wide PVC sheet bending on inner side, and joinedtogether with solvent cement adhesive. An additional 5mmthick PVC strip of 20mm width is to be stuck on the interior side of the „C Channel using PVC solvent adhesive etc.complete as per direction of Engineer-in-charge,manufacture‟s specification & drawing.(For W.C.andbathroom door shutter).

Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal, dehydreresin in glue both sides with approved steel fittings complete as per Annexure „A‟/Decorative Teak veener both side/ 30 mm thick shutter/Add extra for Flush doors/ For double leaf shutter

Providing and laying of paver block as per IS 15658 : 2006 (Indian standard for precast concrete block for pavingspecification) and IRC : SP:63-2004 (guidelines for the use of interlocking concrete block pavement) M-30, 60 mm thick to be used in non traffic areas like building premises, monument premises, land scapes, public gardens/ park, domestic drives, paths and patios, Embankment slopes, sand stabilization Area etc.( As per table 1 of IS 15658:2006

Category „B‟ Denated only two side like I,Z,T shape etc. as per IRC SP 63:2004

Kota stone slab flooring 25 mm thick over 20 mm (average)thick base laid over and jointed with grey cement slurrymixed with pigment to match the shade of the slab includingrubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand)

For area of each slab from 2001 to 5000 Sq.Cm

Providing and fixing Ist quality MAT finished ceremic tile size 300x300mm confirming to IS : 13753 colour such as white, grey, ivory, fume red brown in walls, floors, steps, pillars etc. laid on a bed of neat cement slsurry including nicely finished joints using water proof joint filler power (Untile or Roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster).

P & F 1st qualityHeavy Duty Vitrified Polished Digital tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1: 4 including grounting the joints with white cement and matching pigment etc complete. Size 300mm x 450mm

P & F Bib Cock (IS:8931 Mark) Superior quality of approved make :C.P. Brass bib cock, 15 mm nominal bore.

P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc.C.P. Inlet connection 15 mm Brass (IS:8931 marked).

P & F Indian type white glazed vitreous china Ist quality W.C. orissa pan (IS:2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor :

Size 530x410mm

P & F G.I. Pipes (Internal work) with G.I. fittings (IS:1239 Mark) & M.S. clamps including cutting and making good the walls and floors :15 mm dia nominal bore

P & F Low level Flushing Cistern of 10 litres capacity (IS:2556 mark) of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS:1703 mark) complete including cutting and making good the wall :

Construction of soakage Trench in all types of soil with 300 mm thick dry stone masonry, 80 mm thick stone slab covering, jointing of slab in CM 1:3 Ralthal, Kharanja, 40 mm thick M-15 grade C.C. flooring earthwork etc. complete as perapproved drawing including disposal of earth within a lead of 50 Mtr.:--do- 240 Cm., -do- 150Cm. & depth 300 Cm

Renewing glass panes with wooden fillets wherever necessary

Float glass panes of thickness 5 mm