Military Engineer Services Tender
If you're looking for Rajasthan tenders online and are tired of typing tender ID over and again or going through the cumbersome government websites for it, you are in luck. We have collated every Eproc Rajasthan tender on BidAssist. And for any queries related to an e-tender Rajasthan, like bidding process, registration process, etc., are explained below. Read on.
Costs
EMD
₹ 80,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_641324_1Bid Award Id
ViewTender No
GE/JODH (A) NO 1- OF 2023-24 (9226/E8)Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
... More
Dismantling glazed tiles/ kota stone/ terrazzo tiles any type as in dado/ skirting etc; including cement mortar bedding ( but not backing ) complete all as specifide.
745
-
-
... More
M&L for non skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.
200
-
-
... More
M&L for non skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.
100
-
-
... More
M&L for non skid ceramic tiles 7 - 8mm thick (square/ rectangular) as in skirting / dado, cut out of ceramic tiles of size exceeding 0.11 sqm but not exceeding 0.18 sqm, (Matching with floor tile of the same room) set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and as directed.
10
-
-
... More
M&L for non skid ceramic tiles 7 - 8mm thick (square/ rectangular) as in skirting / dado, cut out of ceramic tiles of size exceeding 0.18 sqm but not exceeding 0.38 sqm, (Matching with floor tile of the same room) set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and as directed.
25
-
-
... More
M&L for non skid ceramic coloured tiles of approved shade and pattern, 7 to 8 mm thick , area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm laid in floor, set and jointe (square/ rectangular) in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.
100
-
-
... More
M&L for glazed ceramic coloured tiles of approved shade and pattern of size 350x 250x7mm/ 450X350X7mm/ 300X450X7 to 8mm thick or any other nearer size as approved by Engineer incharge in vertical surface set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 as in backing coat of tiles complete all as specified and as directed.
300
-
-
... More
M&L for 16 -18mm thick granite (colour as approved) work (table rubbed and polished) in steps, shelves, jambs, pillars, window-cills, cooking platforms (vertical/ horizontal) and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 10mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.
15
-
-
... More
M&L for machine cut kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.
100
-
-
... More
M&L for mirror polished machine cut kota stone slab 15-16 mm thick in riser of steps, skirting, dado and pillar laid over and including 10mm thick rendering in CM 1:4 and jointed complete all as specified and as directed.
15
-
-
... More
M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, 50 mm thick, surfaces finished even and fair without using extra cement including provision of construction joints complete all as specified.
120
-
-
... More
M&L for 75mm thick PCC 1:4:8 type D-2, (40mm graded stone aggregate) as in sub floor, sub bases, floor and paving etc; complete all as specified.
125
-
-
... More
Providing and laying 60mm thick factory made table vibratory, PU mould, chamfered edge cement concrete coloured paver block of M-35 grade with approved design & pattern as in footpath, drive ways or parking etc; over and including 50mm thick compacted bed of fine sand and proper embedding/ laying of inter locking paver blocks into the sand bedding layer, filling the joints with sand and cutting of paver blocks as required, complete all as specified and as directed.
125
-
-
... More
Providing and laying factory made kerbs stone any size of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3, embedded in position including all necessary excavation, tamping ground around blocks and removal of rubbish/ surplus soil etc; making joints with or without grooves, drainage opening wherever required complete all as specified and as directed.
3
-
-
... More
M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in kerbs or benching etc including necessary form work complete all as specified.
1
-
-
... More
Dismantling of stone/ brick work masonry, built in cement mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stone work, serviceable stone aside for reuse and removing unserviceable material in low laying area complete all as specified and as directed.
15
-
-
... More
M&L for squared rubble walling Jodhpur type, brought upto course, well bonded bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed.
10
-
-
... More
All as per srl item No 18 but except stone complete all as specified and as directed.
5
-
-
... More
Extra over for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm and dressing face beds and joints as specified to squared rubble walling,Jodhpur type, brought upto courses all as specified and as directed.
25
-
-
... More
Taking down cement plaster, any description, on brick or stone walls etc, including raking out joints, hacking for key, scrubbing down with water etc and disposal of debris complete all as specified and as directed
1200
-
-
... More
M&L for rendering 15 mm thick in CM 1:6 over stone masonary, concrete surfaces, finished even and smooth (without using extra cement), all as specified and as directed.
750
-
-
... More
M&L for 15 mm thick rendering on stone masonary wall surfaces in CM 1:4 finished fair and even all as specified and as directed.
250
-
-
... More
M&L for 10mm thick rendering in CM 1:3 on ceiling surfaces finished surfaces even and smooth without using extra cement complete all as specified and as directed.
200
-
-
... More
M&L for dubbing out average 20mm thick in cement plaster 1:4 on uneven/ irregular surface such as walls / ceilling / chajjas etc. complete all as specified and as directed.
150
-
-
... More
Preparing new or previously untreated surfaces of steel or iron work of any description and girth over 10cm and applying two coats of synthetic enamel paint complete all as specified and as directed.
10
-
-
... More
Preparing new plastered surfaces and M&L for applying chalk whitening/ concrete primer and /or cement base putty as required incl preparing the surfaces smooth by rubbing and / or sandpapering and M&L two coats of Distemper oil Emulsion on new plastered surfaces complete all as specified and as directed.
750
-
-
... More
Preparing new plastered surfaces and M&L for applying concrete primer and /or cement base putty as required incl preparing the surfaces smooth by rubbing and / or sandpapering and M&L two coats of cement base paint on new plastered surfaces complete all as specified and as directed.
250
-
-
... More
Preparation of new plastered surfaces of walls etc. & applying three coats of lime white wash on walls complete all as specified and as directed.
100
-
-
... More
Preparation of new plastered surfaces of ceiling etc. & applying three coats of lime white wash on ceiling complete all as specified and as directed.
200
-
-
... More
S&F low carbon annealed wire in hexagonal shape 1.0mm diametre chicken wire mesh of size 25mm (distance between the faces of the hexagon), durable twisted woven mesh for mounting on curved and angled surfaces including 15cm lap at junction fixed with nails and properly stapled complete all as specified and as directed.
150
-
-
... More
M&L for carrying out water proofing treatment for sunken portion in the following stages - (i) Taking down of existing sunken slab treatment from the sunken portion and cleaning the surfaces washing down with water and rubbish of the pemises , cleaning and filling cracks with sealing compound, brushing neat cement slurry @ 3.00kg/sqm and grouting 25mm thick cement concrete type B-0 (1:2:4) using 12.5mm graded stone aggregate on sunken slab portion and finishing the top surfaces even and smooth without using extra cement. (ii) M&L for two coat of acrylic cementitious water proofing coating (Dr FIXITpidifin 2k manufactured by M/s Pidilite Industries Ltd or equivalent) and followed by a overlay protective screed (10mm thick cement mortar (1:4) along with liquid water proofing compound approved make as per manufacturer's instructions) on top surfaces of sunken slab after preprations as mentioned above. Method of application for acrylic cementitious water proofing coating achieved as per manufacturers instruction complete all as specified and directed.
70
-
-
... More
Supply only integral water proofing liquid ISI marked
5
-
-
... More
Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 110mm bore complete all as specified & directed.
57.5
-
-
... More
Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 75mm bore complete all as specified & directed.
60
-
-
... More
S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified & directed.
30
-
-
... More
S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified & directed.
27.5
-
-
... More
S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls complete all as specified & directed.
30
-
-
... More
S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls complete all as specified & directed.
30
-
-
... More
S&F 75 mm bore PVC (SWR) bends any radius
15
-
-
... More
S&F 110 mm bore PVC (SWR) bends any radius
15
-
-
... More
S&F 100mm bore pipe PVC (SWR) vent cowls, complete all as specified & directed.
10
-
-
... More
S&F 75mm bore pipe PVC (SWR) vent cowls, complete all as specified & directed.
10
-
-
... More
S&F in repairs Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified & directed by Engineer-in-charge.
20
-
-
... More
Demolition and breaking up drain pipe 150mm dia (Salt glazed ware, AC or Reinforced Concrete) set in cement mortar
15
-
-
... More
Supply & laying jointing and testing 150mm bore reinfirced conctete pipes class NP-2 laid and jointed in cement mortor 1:1 complete with collars or socket/spigot type laid jointed and haunching at side in cement complete all as specified and directed.
15
-
-
... More
M&L for Cutting into existing manholes for removing existing branch drain and connecting new drains, making good to walling and rendering, cutting out branch channel, and making good benchings for 150mm dia pipe
5
-
-
... More
M&L for cement concrete type E-2, 1:5:10 (40mm graded crushed stone aggregate) as in sunken portion complete all as specified.
10
-
-
... More
S&F 40mm bore steel water tubing medium grade galvanised inserted at the end of lateral slope projecting at least 15cm beyond the outer most projected part of the building below the drain pipe up to two storey construction as spout for sunken complete all as specifide.
5
-
-
... More
Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each and removing from site or to store as directed by Engineer incharge.
75
-
-
... More
Taking down shutters any description exc 1.00 sqm but not exc 2.00 Sqm each and refixing the shutter in same opening after easing and adjusting complete as directed by Engineer in charge.
5
-
-
... More
M&L for fabrication of aluminium powder coated window/ vents any pattern & design (openable with hinges, sliding, tilt and turn, casement , fixed type, villa type, ventilators) fabricated with anodized aluminium rectangular or any type section in frame with approved design & patterns including provn of fixing galvanised mild steel wire cloth on the outer side of frame etc; fixed in position all as specified and directed. Note:- Glass pane & galvanised mild steel wire cloth shall be measured and paid separately under respective Items of Sch 'A'.
75
-
-
... More
S&F for figured glass, pin head type ordinary quality, 4mm thick, area of each pane not exceeding 0.5Sqm and glazing with aluminium beading in aluminium frame all as specified and as directed.
4
-
-
... More
S&F of galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified & as directed.
4
-
-
... More
S&F of factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing S&F
45
-
-
... More
S&F of solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.
143
-
-
... More
S&F of 100 mm size PVC/ Stainless Steel (as approved by Engineer incharge) butt hinges all as specified and directed.
90
-
-
... More
S&F mild steel door handles, stove enameled black, 150 mm long and fixed with steel screws complete all as specified.
60
-
-
... More
S&F of mild steel barrel tower bolts, stove enameled black, with bright bolt, 150 mm long and fixed with steel screws complete all as specified.
60
-
-
... More
Dismantling wrought iron or mild steel work of any description and in any position not otherwise specifically provided for (framed/ unframed work) complete all as specified.
0.4
-
-
... More
S&F of framed work as in doors chowkats of MS angle iron or MS hollow square/ rectangular any type/ size with gusset plates, rails, braces,cooler stand, chajja framed complete drilled for fixing of door etc; to be prepared for hanging with and including hold fasts and locking arrangements confirming to FE- 290 (Gde-E- 165) complete all as specified and directed by Engineer-in-charge.
100
-
-
... More
Dismantling stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar complete all as specified.
25
-
-
... More
M&L Jodhpur stone roof slabs, self faced exceeding 10cm but not exceeding 12.5 cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in cement mortar 1:3, complete all as specified and as directed.
20
-
-
... More
All as per Srl Item above but, except stone complete all as specified and as directed.
5
-
-
... More
M&L for plain cement concrete 1:3:6 type C-1,using 20mm graded stone aggregates as in coping to parapet walls including necessary formwork complete all as specified and as directed.
7
-
-
... More
M&L for carrying out water proofing treatment for roofs in the following stages -
(i) Rendering 10mm thick in cement mortar (1:4), mixed with integral water proofing liquid all as per manufacturer's instructions over concrete surfaces finished even and smooth with out using extra cement. Note : (WPC shell be measured separately and paid for under respective item of schedule).
(ii) First coat of bitumen primer confirming to IS 3384 @0.300 Kg/ Sqm over plastered surafces
(iii) Second layer of 3.0 mm thick APP modified polymeric membrane with centre core of Single non woven polyster reinforcement and having weight 3 Kg/ Sqm with mineral gravel finish on top complete laid with blown type bitumen confirming to IS 702-1988 grade 85/25 @ 1.20 Kg/ Sqm complete all as specified and as directed.
(iv) Finally applying two protective coats of bituminous aluminium based reflective paint to safeguard against UV, including preparing of surfaces of APP modified polymeric membrane (second coat apply after 24 hrs or as per manufacturing instructions).
1000
-
-
... More
M& L for carrying out water proofing treatment for roof in the following stages :- (a) first Course : Rendering 10 mm thick plaster with CM 1:3 mixed with water proofing compound as per manufacturee instructions over concrete surfaces finished even and smooth without using extra cement.
(Note: - WPC shall be measured separately and paid for under respective item of schedule) (b) Second Course : One coat of bitumen primer T-10/polymerised confirming to IS 3384 @ 0.30 ltr/Sqm over plastered surface. (c) Third Course : A layer of 3.0 mm thick APP modified polymeric membrane with centre core of Single non woven polyster reinforcement and having weight 3 Kg/ Sqm with mineral gravel finish on top complete laid with blown type bitumen confirming to IS 702-1988 grade 85/25 @ 1.20 Kg/ Sqm complete all as specified and as directed. (e) Fourth Course : Top most layer that shall act as a protective layer shall be with 40mm thick PCC 1:2:4 Type B1 using 20 mm graded stone agg finished even & smooth without using extra cement laid to slopes as required at site & filling the joints with bitumen mastic ( Mix of bitumen & sand in the ratio 1:1) made @ 0.90 to 1.20m both ways (10mm wide 12 mm deep) made while the conc is still green all as specified and as directed.
800
-
-
... More
Taking down 15mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specifide.
300
-
-
... More
Taking down 20mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specifide.
250
-
-
... More
Taking down 25mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specifide.
150
-
-
... More
S&F 15mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and as directed.
250
-
-
... More
S&F 20mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and as directed.
200
-
-
... More
S&F 25mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and as directed.
100
-
-
... More
Fixing only 15mm bore steel water tubing any grade with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and as directed.
50
-
-
... More
Fixing only 20mm bore steel water tubing any grade with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and as directed.
50
-
-
... More
Fixing only 25mm bore steel water tubing any grade with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and as directed.
50
-
-
... More
S&F as in repairs Vitreous china squatting pan, Orissa pattern, size 580x440mm white/ coloured with integral foot rests including flus pipe and connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete all as specified and as directed.
15
-
-
... More
S & F as in repairs vitreous china wash down water closet European Type pedestal pattern with seat & cover as in repairs with jet spray complete incl fixing of flush pipe etc complete all as specified and directed.
6
-
-
... More
S&F in repair PVC 10 ltr. Cap. valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc. complete all as specified and as directed.
15
-
-
... More
S&F in repair vitreous china wash basin, white/ coloured, flat back, size 550x400mm including PTMT waste fittings, 32mm bore size, waste pipe pvc 32mm bore and angle iron brackets of required size and length etc. and making good disturbed surfaces to match with the existing complete all as specified.
15
-
-
... More
Low density polythene pipe (LDPE) of pressure rating 6 Kg per Sq.cm, 450 mm long, heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipe as in repair complete all as specified.
30
-
-
... More
Disconnecting existing PVC tank exc 500 Ltrs and not exc1000 Ltrs setting aside (or lowering if required), cleaning (Cleaning and removing all scale and dirt, etc; from tanks and from mouth of circulating pipe etc;) and hoisting if required reconnecting and re-fixing in position complete all as specified and as directed.
15
-
-
... More
S&F in repair 500 ltr capacity rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) and in white colour hoisted and fixed in position including 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified in SSR Part-I including taking down existing tank complete all as specified and as directed.
10
-
-
... More
S&F in repair 1000 ltr capacity rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) and in white colour hoisted and fixed in position including 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified in SSR Part-I, including taking down existing tank complete all as specified and as directed.
15
-
-
... More
S&F 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (minimum weight for 25mm ball valves-455gms) fixed in repairs i.e., incl taking down and removal of old unserviceable float valves complete all as specified and as directed.
15
-
-
... More
S&F in repair 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified.
25
-
-
... More
S&F in repair 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified.
15
-
-
... More
S&F in repair 600x450mmx 5mm thick, looking mirror of selected quality mounted on 6mm thick commercial plywood and fixed to wall with plug and steel screws etc. complete all as specified and as directed.
15
-
-
... More
S&F in repair 15mm bore chromium plated bib taps (ISI marked) fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.
30
-
-
... More
S&F in repair 15mm bore chromium plated pillar taps (ISI marked), fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.
15
-
-
... More
S&F in repair 15mm bore stop valve/ angle stop cock chromium plated (ISI marked) fancy type cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe with long shank and cup complete all as specified.
30
-
-
... More
S&F in repair chromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe or union suitable for 15mm bore pipe etc; complete all as specified.
20
-
-
... More
NOTE:- (i)- The contract sum shall be arrived at after duducting amount of schedule of "Credit" from the Total quoted amount
-
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements