Military Engineer Services Tender

Replacement of long, front and back rail, rest made of well seanoned teak wood duly painted / smoothened after taking out old unserviceable one of single seater chair all as specified.

Replacement of short stiffeners well seasoned 1st quality teak wood all as specified in drawings after taking out the old existing unserviceable one of 3 seater /single seater all as specified.

Replacement of front legs of well seasoned teak wood all as specified in drawings after taking out the old existing unserviceable of Sofa Chair 4/5 seater all as specified.

Replacement of back legs of well seasoned teak wood all as specified in drawings after taking out the old existing unserviceable of Sofa Chair 4/5 seater all as specified.

Replacement of Arms well seasoned teak wood all as specified in drawings after taking out the old existing unserviceable of Sofa Chair 4/5 seater all as specified.

Tightening of complete sofa set and polishing all new and old surface with two caots of french polish after preparation and complete removing of existing polish of old surface complete all as specified.

Chair dinning Cushioned /long back, Drg No. FD/E6/MAP/10(R) Replacement of seat cushioned 75mm thick made of cool foam (Make : Sleepwell/ Kurlon) of 40 density including ply wood 12mm thick suitable for seat duly covered with well finished best quality tapestry cloth not less than Rs 200/- meter shade and quality shall be approved by BSO/GE.

Replacement of front legs made of well seasoned teak wood duly plaine/ smoothened after taking out the old unserviceable front legs all as specified.

Replacement of rear legs rest all as per serial item No. 2.01 here-in-before all as specified.

Replacement of front and back rail well seasoned teak wood all as specified in drawings after taking out the old existing unserviceable rails all as specified.

Replacement of side rail well seasoned teak wood all as specified in drawings after taking out the old existing unserviceable side rails all as specified.

Replacement of back rest , side and middle stiffner well seasoned Sheesham wood all as specified in drawings after taking out the old existing unserviceable stiffners all as specified.

S&F second class hard wood corner / bracket (L shape) of size 50mm x 50mm x 20mm thick fitted with screw between side rail to legs all as specified.

Tightening of complete sofa set and Polishing all new and old surface with two caots of french polish after preparation and complete removing of existing polish complete all as specified.

Chair easy Cushioned, Drg No FD-358 Replacement of seat cushioned 75mm thick made of cool foam (Make : Sleepwell/ Kurlon ) of 40 density duly covered with well finished best quality tapestry cloth not less than Rs 200/- Per meter shade and quality shall be approved by BSO/GE.

Replacement of back cushioned 75mm thick made of cool foam (Make : Sleepwell/ Kurlon) of 40 density duly covered with well finished best quality tapestry cloth not less than Rs 200/- per meter shade and quality shall be approved by BSO/GE.

Replacement of front legs made of well seasoned teak wood duly plained/ smoothened after taking out the old unserviceablefront legs all as specified.

Replacement of rear legs rest all as per serial item No. 3.02 here in before all as specified.

Replacement of front and back rail well seasoned teak wood all as specified in drawings after taking out the old existing unserviceable rails all as specified.

Replacement of side rail well seasoned teak wood all as specified in drawings after taking out the old existing unserviceable side rails all as specified.

Tightening of complete sofa set and Polishing all new and old surface with two caots of french polish after preparation and complete removing of existing polish complete all as specified.

Chair revolving / chair computer, Drg No. FD-E6/MAP/01 and TP M&L Tapestry cloth/ ragzine over sythetic foam 25mm thick (as approved) for seat of chair computer/chair revolving including taking out old worn out Tapestry Cloth/ ragzine & Foam from chairs and seat 12mm hot pressed plywood complete all as specified and as directed.

M&L Tapestry cloth/ ragzine over sythetic foam 25mm thick (as approved) for back of chair computer/chair revolving including taking out old worn out Tapestry Cloth/ragzine & Foam from chairs and back 12mm hot pressed plywood complete all as specified.

S&F the completely new seat and back of chair computer long back over 12mm hot pressed plywood covered with tapestry cloth/ ragzine of approved quality to match the original complete all as specified and directed.

M&L twin Castor Wheel (as approved) of chair computer/chair revolving including taking out unserviceable or broken Caster Wheel from Chairs, complete all as specified.

M&L bottom base with stainless steel frame including twin castor wheel each chair five Nos (as approved) of chair executive medium back including taking out unserviceable bottom base with twin castor Wheel from Chairs, complete all as specified.

M&L as lifting hydrolic system of chair computer/chair- revolving including taking out unserviceable Gas Lifting Hydrolic System from Chairs, complete all as specified.

M&L handle soft foam of chair computer/chair visitor/chair revolving including taking out unserviceable handle from Chairs including welding of broken joins and painting of steel surface of the chair with one coat of synthetic enamel of black shade complete all as specified.

Chair writing/ chair visitor, Drg No. FD/MAP/E6/12 S&F Tapestry/Fabric cloth over sythetic foam 25mm thick (as approved) for seat of chair writing/ chair visitor including taking out old worn out Tapestry / Fabric Cloth & Foam from chairs and seat 12mm hot pressed plywood complete all as specified and as directed.

S&F Tapestry/Fabric cloth over sythetic foam 25 mm thick (as approved) for back of chair writing/ chair visitor including taking out old worn out Tapestry/Fabric Cloth & Foam from chairs and seat 12mm hot pressed plywood complete all as specified.

M&L the completely new seat and back of chair writing over 12mm hot pressed plywood covered with tapestry cloth/ ragzine of approved quality to match the original complete all as specified and directed.

S&F PVC buffer of best quality as directed and approved by BSO/GE complete all as specified and directed.

S&F handle soft foam of chair writing/ chair visitor including taking out unserviceable handle from Chair including welding of broken joints and painting of steel surface of the chair with one coat of synthetic enamel of black shade complete all as specified and as directed. Note :- (i) Cost of minor repair like welding to frame if required etc is deemed to be included in the quoted rate of this item. (ii) Cost of all type nut bolts and screws and painting of the chair to be included in the quoted rate.

Bed hard with steel frame, Drg No. FD/E6/MAP/08(R) Removing of old unserviceable ply wood from Bed hard with steel frame and supply and fixing 12mm thick ply wood sheet on top suitable for Bed hard with steel frame as shown on drg of size 1980 x 900mm (BWR) as per IS-303 with mild steel galvanized iron nuts & bolts with GI washer (Heavy weight) and including electric welding of loose long rail short rail, legs centre stiffender, Head rest, Foot rest and cleat of MS pipe by continuous welding around the broken joints and also replacement of old unserviceable above parts with new parts where required and also including painting with one coat of synthetic enamel paint (Black) after preparation of old painted surfaces with provding 04 Nos new hard rubber shoe to each Bed hard with steel frame at the bottom of legs after removing of old shoe complete all as specified and as directed. Note :- (i) Cost of minor repair like welding to frame if required etc is deemed to be included in the quoted rate. (ii) Cost of all type nut bolts and washers, PVC shoes and painting of the Bed hard steel to be included in the quoted rate.

S&F of new head rest made of MFD board of 18mm thick both side teak face of exterior grade with 4mm thick teak wood beading shall be provided all-round including screws and welding of cleat all as specified in drawing directed.

S&F of new Foot rest made of MFD board of 18mm thick both side teak face of exterior grade with 4mm thick teak wood beading shall be provided all-round including screws and welding of cleat all as specified in drawing directed.

Charpoy Folding Steel, Drg No. FD-388(R) Removing of old unserviceable plywood from charpoy folding and supply & fixing 12mm thick commercial plywood BWR grade in two pieces fixed with four nuts, bolts, washers of suitable size for each piece of plywood and provide support in between long rail of charpoy complete all as specified and directed.

S&F in replacement of unserviceable PVC shoe with new PVC shoe of best quality complete all as specified and directed.

Removing of old unserviceable parts of charpoy folding and supply and fixing MS pipe of 25 mm bore with wall thickness 1.6mm by welding and including minor repair/welding complete all as specified as approved/directed.

Painting of steel surface of the charpoy with one coat of synthetic enamel of olive green shade complete all as specified and directed.

Replacement of U/S ply top of Charpoy IP with new Hard top (Drg FD/MAP-II/01) Removing of unserviceable plywood from Charpoy IP, S&F 12mm thick plywood sheet on top, suitable for Charpoy IP as shown on drg of size 1980x900mm (BWR) as per IS-303 with mild steel galvanized iron nuts & bolts of size 70mmx6mm with GI washer (heavy weight) and including electric welding of loose long rail, short rail, legs, centre stiffener 25 x 25 mm square MS tube and cleat tube size of 25x60mmx6mm of MS pipe by continuous welding around the broken joints and also replacement of old unserviceable above parts with new parts where required and also including painting with one coat of synthetic enamel paint (Black) after preparation of old painted surface with providing four nos new hard rubber shoe to each charpoy IP at the bottom of legs after removing of old shoe complete all as specified and directed. Note :- (i) Cost of minor repair like welding to frame if required etc is deemed to be included in the quoted rate. (ii) Cost of all type nut bolts and washers, PVC shoes and painting of the charpoy IP to be included in the quoted rate.

Replacement of U/S ply top/ Nylon Newer of Charpoy GI Pipe with new Plywood top, Drg No. FD-220 Material & Labour for removing of unserviceable nylon newar from charpoy GI pipe, tightening of all loose components of complete charpoy such as check nuts, elbows, long rails, short rails, legs, etc and supply and fixing 12mm thick Plywood, 7 Ply, commercial type, BWR, exterior grade (water proof), ISI marked, of size 1980 mm x 900 mm in single piece fixed on top of Charpoy GI pipe with & including supplying and fixing three Nos stiffeners made out of mild steel flat iron 35mmx5mm, 880mm long between long rails parallel to short rails with equal spacing and power welding duly painted with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, plywood top fixed with and including mild steel galvanized iron nuts & bolts of size 70mm long x 6mm dia (Nos of bolts to be provided - 13 Nos) with GI washers of suitable size (Heavy weight) in sufficient numbers on top of bolts to maintain the plywood top in true leveled position and one GI washer on underside of each bolt for proper tightening of bolt, embossing word "MES” with height of letters 10cm on four corners of the plywood top with thick black synthetic enamel paint, complete all as specified, shown on drawings and as directed. Notes :- (i) The above mentioned size of plywood is firm and no tolerance in size, thickness etc shall be accepted. (ii) Plywood shall be provided in single piece in each Charpoy. (iii) Electric arc welding shall be used to fix stiffeners. (iv) Welding rod shall be ISI marked. (v) Purchase voucher of plywood shall be obtained by the contractor from authorised dealer/manufacturer and shall be submitted to Engineer-in-Charge.

Drg No. FD-220 Material & Labour for removing of old unserviceable long rail of Charpoy GI pipe and supply and fixing new long rail made out of GI tubing 32mm bore, medium grade, ISI Marked, 1980mm long, duly continuous welded properly at both ends as per best trade practice and also duly painted with aluminium paint on welded portion, complete all as specified, shown on drawings and as directed. Make : Jindal/Prakash Surya/Tata/BST Notes :- (i) Welding of new rail shall be as per best trade practice with continuous welding and as approved by GE. (ii) Unit for measurement of this item is ‘Each Job’ which shall comprise of removing of one old long rail and supply and fixing of one new long rail in lieu. (iii) Electric arc welding shall be used. (iv) Welding rod shall be ISI marked.

Drg No. FD-220 Dismantling carefully unserviceable short rail of Charpoy GI pipe and replacement by short rail made out from old long rail GI pipe retrieved under serial item No. 9.01 here-in-before, duly continuous welded properly at both ends as per best trade practice and also duly painted with aluminium paint on welded portion, complete all as specified, shown on drawings and as directed. Notes :- (i) Welding of rail shall be as per best trade practice with continuous welding and as approved by GE. (ii) Unit for measurement of this item is ‘Each Job’ which shall comprise of removing of one old short rail and fixing of one short rail in lieu made out of old long rail. (iii) The rate quoted for this item shall include for making of short rail by cutting from old long rail in appropriate size. (iv) Electric arc welding shall be used. (v) Welding rod shall be ISI marked.

Drg No. FD-220 Supply & fixing in position GI 3 way elbow 32mm bore, medium grade (‘B’ Class), ISI marked all as per sample available in BSO's Yard in Charpoy GI pipe including dismantling & taking out carefully old unserviceable GI 3 way elbow 32mm bore complete all as specified, shown on drawings and as directed.

Drg No. FD-220 Supply & fixing in position GI check nut 6mm thick 32mm bore, medium grade (‘B’ Class), ISI marked all as per sample available in BSO's Yard in Charpoy GI pipe including dismantling & taking out carefully old unserviceable GI check nut complete all as specified, shown on drawings and as directed.

Drg No. FD-220 Dismantling carefully unserviceable leg of Charpoy GI pipe and replacement by leg made out from old short rail GI pipe retrieved under serial item No. 9.02 here-in-before, duly continuous welded properly at one end as per best trade practice and also duly painted with aluminium paint on welded portion, with & including supply & fixing mild steel 5mm thick & 35mm dia plate to the bottom of leg duly continuous welded as per best trade practice and also duly painted with two coats of aluminium paint, complete all as specified, shown on drawings and as directed. Notes :- (i) Welding of leg shall be as per best trade practice with continuous welding and as approved by GE. (ii) Unit for measurement of this item is ‘Each Job’ which shall comprise of removing of one old leg and fixing of one leg in lieu made out of old short rail. (iii) The rate quoted for this item shall include for making of leg by cutting from old short rail in appropriate size. (iv) Electric arc welding shall be used. (v) Welding rod shall be ISI marked.

Drg No. FD-220 Material & labour for electric welding of long rails, short rails, legs of 32mm bore GI tubing by continuous welding around the broken joint duly painted with aluminium paint on welded portion complete all as specified & as directed. Notes :- (i) Unit for measurement of this item is ‘Each’ which shall comprise of welding of each broken joint all as specified above. (ii) Welding rods shall be ISI marked.

Table Centre with Glass Top, Drg No. FD-375 Supply and fixing new 12mm thick glass top of approved colour duly polished complete all as specified and as directed

S&F new Vaccum rubber Shoe at top of legs of table centre to fix the glass top complete all as specified.

S&F PVC Shoe at bottom of legs of table centre complete all as specified and directed.

Chair push back for Auditorium, TP Opening and removing of seat back and arms of chair push back auditorium and tighting & refixing of loose seat, back and arms including foundation. (i.e. complete chair push back, if in serviceable condition) The seat, back and arms if repair/ replaced shall be paid separately under respective items of here in after as "Supply Only". The cost of steel screw, nut &bolt as required etc shall be deemed to be included in the quoted rate of this items all as approved by GE complete all as specified and directed

Removing the torned/ worned out upholstry for seat of chair and S&F new cover made of cloth tapestry cushioned and rexin of approved quality as to match the original complete including all connecting material required for fixing the seat all as specified and directed.

Removing the torned/ worned out upholstry for back of chair and S&F new cover made of cloth tapestry cushioned and rexin of approved quality as to match the original complete including all connecting material required for fixing the seat all as specified and directed.

Removing the old unserviceable leatherized rexine cloth from chair arms and S&F well finished best quality leatherise rexine cloth including foam where required of best quality as approved of red colour not less than Rs. 300 per metre to meet the original including all connecting material required for fixing the arms complete all as specified.

Removing broken/ unserviceable seat ans back and supply the completely new seat and back of approved quality as to match with the existing all as specified and directed.

Labour for removing broken/ unserviceable side armrest of chair and S&F new armrest as to match with the existing complete all as specified and directed.

S&F MS flat iron 25mm width, 5mm thick and 500mm long duly both side hole as per required size, parallel to leg duly painted black will be fixing between the leg to leg centre stiffner with nut & bolt size of 40mm complete all as specified and directed.

Repair of push back system of chair with S&F new spring as per required under the seat. complete all as specified and as directed.

S&F MS fastener 150mm long with nut for tightening of lose chair from foundation complete all as specified and directed. Note :- The cost of all other items required for fixing the chair shall be deemed included in the quoted rate.

Chair Executive Revolving, Drg No. TP M&L Tapestry cloth/ ragzine over sythetic foam 25mm thick (as approved) for seat of chair executive revolving to meet the original including taking out old worn out Tapestry cloth/ ragzine & Foam from chairs complete all as specified and as directed

M&L Tapestry cloth/ ragzine over sythetic foam 25mm thick (as approved) for back of chair executive revolving to meet the original including taking out old worn out Tapestry cloth/ ragzine & Foam from chairs complete all as specified and as directed

S&F the completely new seat and back of chair executive over 12mm hot pressed plywood covered with tapestry cloth/ razine of approved quality and design to match the origional complete all as specified and as directed

M&L bottom base of special design including twin castor wheel each chair five Nos (as approved) of chair executive medium back including taking out unserviceable bottom base with twin castor Wheel from Chairs, complete all as specified.

M&L handle of required design as approved by the BSO of chair executive including taking out unserviceable handle from Chairs including welding of broken joins and painting of steel surface of the chair with one coat of synthetic enamel of black shade complete all as specified. Note: The cost of all other items required for fixing the chair shall be deemed included in the quoted rate.

Dressing Mirror Gents MAP, Drg No. FD/E6/MAP/16 Removing old unserviceable parts and S&F new parts as size and shape including polishing complete all as specified all shown on drawing and directed. Mirro 5.5mm thick with teak wood beading make modiguard/Atul and swastik complete all as specified and directed.

M&L of removing of old unserviceable side runner and replacing it with new 18mm thick pre-laminated particle board (exterior grade) complete all as specified and as directed.

M&L of removing of old unserviceable top and bottom runner and replacing it with new 18mm thick pre-laminated particle board (exterior grade) complete all as specified and as directed.

All as per serial item No. 13.01 here-in-before but back side ply 12mm thick BWR as per IS-303 (7 Ply) complete all as specified and as directed.

Fixing only of dressing mirror gents in ORs MAP qtrs (The fixing dressing mirror properly on the wall, labour for fixing drilling and carrrying charges only). Required material shall be paid seperately under respective items of here in after as supply only.

Supply of nut & bolts with washer size of 150mm long to each dresssing mirror for 04 Nos complete all as specified and as directed.

Supply of MS flat 150mm long width, 5mm thick duly 3 hole to be fixed on top of the dressing mirror including fixing screw etc as required dressing for 02 Nos complete all as specified and as directed.