Military Engineer Services Tender
If you're looking for Rajasthan tenders online and are tired of typing tender ID over and again or going through the cumbersome government websites for it, you are in luck. We have collated every Eproc Rajasthan tender on BidAssist. And for any queries related to an e-tender Rajasthan, like bidding process, registration process, etc., are explained below. Read on.
Costs
EMD
₹ 1,12,000Document Cost
₹ 1,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2025_MES_694675_1Tender No
82425/108/E8Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.
387
-
-
... More
Material & Labour for Non-Skid White Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.
75
-
-
... More
Material & Labour for White Glazed ceramic tiles in vertical surface 300mm X 600 mm X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick cement plaster in ement mortar 1:4 as backing coat on fair faces on stone surface all as specified and directed.
312
-
-
... More
Supply and fixing for PCC coloured interlocking ( glossy finishing) paver blocks confirming to IS-15658-2006 of 60 mm thickness, M-35 grade as in hardstanding etc. laid over and including 50 mm thick screed or bedding layer of sand, complete all as specified.
134
-
-
... More
Material and labour for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, over and including cement screed bed 15 mm thick in cement mortar (1:6) base including rubbing and mirror polishing, and half nose moulding (bull nosing) etc,complete all as specified.
650
-
-
... More
All as per item No. 8.00 here-in-above, but pre-polished kota stone as in vertical surfaces such as skirting and risers over and including 10mm thick plaster in cement mortar (1:4) on brick work or concrete surfaces, complete all as specified.
275
-
-
... More
Material and labour for mirror polishing of existing Kota stone in flooring , skirting, riser and treads etc with and including grey cement slurry mixed with pigment to match shade of kota stone wherever as required complete.
250
-
-
... More
Material and labour for machine cut Prepolished Kota stone slab 20-25 mm thick (of size not less than 55 cm x 55 cm in flooring and 120 cm x 25 cm in treads) laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including half round edge moulding, over and including cement screed bed 15 mm thick in cement mortar (1:6) base including rubbing and mirror polishing, and half nose moulding (bull nosing) etc,complete all as specified.
30
-
-
... More
Material & Labour for machine cut Prepolished Kota stone slab 20-25 mm thick (of length not less than 55 cm in skirting and 120 cm in risers) laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) but as in vertical surfaces such as skirting and risers over and including 10mm thick plaster in cement mortar (1:4) on brick work or concrete surfaces, complete all as specified.
10
-
-
... More
Material & Labour for Granite work (Jet/Telephonic Black) 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, counter basins, urinal partitions etc. and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types and including 15mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces and half nose moulding (bull nosing) etc, complete all as specified and directed.
15
-
-
... More
Material and Labour for PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in sub base/levelling coarse and finished the top surface even and fair complete all as specified.
37.4
-
-
... More
Material & Labour for brickwork with old size fly ash bricks straight or curved on plan exc. 6 M mean radius built in CM 1:6, complete all as specified and as directed.
5
-
-
... More
Material and Labour for PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base/mass concrete and finished the top surface even and fair complete all as specified.
10.05
-
-
... More
Material & Labour for 75 mm thick Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection with fair finished complete. Note : Joints 12 mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.
135
-
-
... More
Supply and fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 65 mm x 125 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company.
100
-
-
... More
S&F for 2nd class hard wood 35mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete.
42
-
-
... More
Supply and fixing IInd class (hollock) hard wood factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed.
42
-
-
... More
Supply and fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 50 mm x 100 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company.
90
-
-
... More
Supply and fixing factory made solid PVC moulded door shutter with wood free EPS 28 to 30 mm thick (Stiles), with 2, 4, or 6 raised panel design with 2 mm thick moulded PVC sheet on the front page and 2 mm plane colour PVC sheet on back face supplying and fixing in frames at site as per speicfication and drawing.
25
-
-
... More
Supply & fixed 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed.
160
-
-
... More
Supply & fixed 150 mm long Extruded aluminium alloy handles, fabricated type anodised complete all as specified.
160
-
-
... More
Supply & fixed 100 mm butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and directed.
240
-
-
... More
S&F 100 mm long stainless steel butt hinges with galvanised MS hinge pin etc.
60
-
-
... More
S&F alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified.
40
-
-
... More
S&F double legged door stopper of overall length of cover plate 150 mm of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floors and rubber all as specified and directed by Engr-in-charge.
30
-
-
... More
Supply & fixed MS helical door spring 300 mm long fixed with screws to wooden chowkhats or fixed with welding to steel chowkhats.
30
-
-
... More
Supply & Fixed in repairs aluminium Hat and coat hooks, solid body, 175mm to 250 mm
8
-
-
... More
Material & labour for fabrication of pressed steel cupboard shutter using 0.8mm thick MS plain sheet with frame 1.25mm thick bent to shape including two coat of synthetic enamel paint on internal surfaces & two coat of hammer tone finish on external surface alongwith locking arrangement mortice lock ,handle etc complete all as specified as per drg No CEJZ/TD/12/2008 sheet 1/3 to 3/3.
16
-
-
... More
M&L for providing and fixing of window, ventilator fabricated from roll formed sections made of galvanized steel colour coated /powder coated (Base steel as per IS 513 'D' quality, Galvanized as per IS 277 with Zinc of 120 grams/Sqm) with total coated thickness of 0.60 mm Paint specifications: Coated Sections should be coated with primer Coat of Epoxy Primer of 5-7 microns thick, finish painted with Polyster paint of 12-16 micorns thick and back coated with Alkyd backer of 5-7 microns, or Powder Coated with pure Polyster Powder up to 50-60 microns thick. Dimensions of Sections :Sections for Frame of 72mm x 50mm, Section for Mullion of size 72mm x 50mm, Section for Shutter Frame of size 47mm x 20mm, Section for Frame Glass Beads of 12mm x 12mm, and Section for Fly mesh of 40mm x 20mm. Fixing Details : Section for Frame Glazed Shutters and Mesh Shutters should be cut to length and miter joined with Polypropylene Corner Brackets, Mullion Section should be joined to the Frame/Mullion using Nylon Cap. Ethyl Propylene Daimine Monomer (EPDM) Gasket should be used all around glass in shutter and fixed galss. Rubber Gasket should be used around Fly mesh to fix in Mesh Shutter. Accesories: Each Glazed shutter should be provided with S.S.
Pivot Hignes-01 set, Seccolor Handle & Seccolor Stay Glass: Glazed shutter and fixed glass portions to be provided with a glass of 5 mm plain float Glass. Mesh: Mesh shutter shall be provided with a stainless steel 32 guage Fly mesh of 304 grade with 144 holes per sq. Inch. Windows shall be provided with grill made of 10mm Sqm bars welded to at 150mm centre-to-centre, 6mm x 12mm MS flat Iron. Total grill unit should be powder coated and fixed to window frame with screws. Window frame should be fixed to brick/concrete masonory by using Nylon self-expanding caps and driving MS electroplated 80 mm long screws into the caps through frames. Note: The item includes everything as, painting the surfaces, fixing, all necessary accesories, glass, mesh, etc, all as per given spcifications, complete all as specified and directed by Engr-in-charge.
95.8
-
-
... More
Supply and fixing stainless steel wire cloth,0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.
22
-
-
... More
Supply and fixing (in repair) galvanized mild steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or galvanized wire staple and including fixing with beads supplied with joinery when fixed in panels of joinery, complete all as specified.
20
-
-
... More
Supply and fixing for mild steel framed work as in door chowkats/gate of angle or angle iron work as in fixing by drilling/cutting the stone masonry wall and fixing for particle board & other section of grade Fe-290-Gde E-165 with gusset plate rails, braces etc welded/drilled to fixing of steel sheeting or other covering doors etc. to be prepared for sliding or hanging with and including either hooks and hinges or steel hanging door fittings (exclusive steel sheeting or other covering, running rails & guides), complete all as specified and as directed by the Engr-in-Charge.
250
-
-
... More
Supply and fixing of prelaminated 18/19mm thickness particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work.
25
-
-
... More
Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames, glazed with putty or fixed with beads.
15
-
-
... More
Supply & fixing in repairs stainless steel type curtain rod 22 to 25mm dia as per sample
125
-
-
... More
Supply & fixing of purpose made brackets trade pattern for stainless steel decorative type curtain rods suitable for holding 22 to 25mm dia as per sample as in repair.
208
-
-
... More
Supply & fixing of stainless steel decorative fincals(round type with mirror optic finish)trade pattern for decorative type curtain rods suitable for 22 to 25mm dia curtain rods as per sample as in repaie complete all as specified.
208
-
-
... More
Supply & fixing of stainless steel decorative fincals wall to wall trade pattern suitable for decorative type curtain rods 22 to 25mm dia as per sample as in repair complete all as specified.
5
-
-
... More
Supply only liquid water proofing compound, ISI marked complete all as specified and directed.
12.99
-
-
... More
Supplying & laying 03 coats of reinforced acrylic coating ‘New Coat’ as on sunken floor applied @1.5 Ltr/Sqm in 03 coats to achieve total 1mm thickness in any position including cleaning surface of sunken slab with wire brush/mechanical brush and with water thoroughly to remove all dust/dirt and loose particles to expose base concrete/sunken slab etc including repairing of loose/defective joints and applying 15mm thick plaster in CM 1:3 to level the surface and treatment to be applied all as per manufacturers instructions, complete all as specified and directed.
58
-
-
... More
Material & labour for 100mm thick PCC 1:2:4 type B-1, (20mm graded aggregate) as in sunken floor complete all as specified and directed
33
-
-
... More
M&L for dismantling and taking down existing loose/ spalling/ unsound/ weaken concrete, unserviceable plaster from RCC components of any description and in any position until sound cocncrete substrate is obtained by chisel and hammer or using robust pneumatic chisel, hand tools including cutting of all edges, making square shoulders of the aperture, coarsen the smooth surfaces including necesary preparation of surfaces and cleaning the surface free from dust and debris etc. to ensure maximum bonding between the substrate and coating system including removing of all debris to a distance exceeding 1.5 Km but not exc. 5 Km complete all as per manufacturer's instructions, as specified and as directed.
250
-
-
... More
M&L for preparation of surfaces cracks of plaster internal/external of walls, ceilings/Chajjas upto 5 mm wide, remove the loose plaster/concrete by suitable tools, filling cracks with crack paste compound and apply the second coat after 10-12 hrs of application of first coat including necessary scafolding of any height all as specifed and directed.
85
-
-
... More
M&L for preparation of surfaces by cutting 'V' groove cracks of plaster internal/external of walls, ceilings/Chajjas all along the crack 5 mm to 10 mm and remove the loose plaster/concrete by suitable tools, filling cracks with crack paste compound and apply the second coat after 10-12 hrs of application of first coat and for external application must be coated with paint including necessary scafolding of any height all as specifed and directed.
85
-
-
... More
M&L for providing and fixing welded MS wire mesh weighing not less than 1 kg/sqm on the prepared surface which should be cleaned and should be removed from dirt, fungus and all foreign material.complete all as specified and directed by Engineer-in-Charge.
100
-
-
... More
M&L for providing and applying the treated surface with high quality repair mortar with polymer and fibre content .water ratio of which shall be 0.16, 28 days compressive strength shall be 30 MPa,mixed density shall be 2.18 kg/ltr, flexural strength shall be 6 MPa for 7 days and tensile strength for 7 days shall be more than 2MPa.Its adhesion bond strength shall be greater than 2 MPa with creep strain reduction of 8%. The modulus of elasticity of this product shall be 23-26 KN/mm². It shall not bleed / segregate on adding water and shall provide dual shrinkage compensation i.e – both plastic & hardened.Cement , sand can be used for finishing purpose. It shall be capable of being applied in thicknesses of 20 mm without sagging or falling and shall have minimum adhesive bond strength of 2 MPa.All cementitious systems have to be cured for a minimum period of 15 days by water curing,complete all specified and directed by Engineer-in-charge.
100
-
-
... More
M & L for providing and applying a layer of high solids resin based pigmented concrete compound (application 4.00 to 5.00Sqm/lit) It forms a continuous membrane that controls hydration for strong and durable concrete .It should have specific gravity of 1.02. It can be applied by brush or can be sprayed, If sprayed the nozzle of the spray should be held approximately 450mm from the concrete surface and should be passed back and forth to ensure complete and even coverage. The pump pressure should be maintained at a level to produce a fine spray ensuring complete coverage of the surface, complete all specified and directed by Engineer-in-charge.
100
-
-
... More
M&L for providing and applying two coats of water based Aliphatic acrylate -Anti-Carbonation coating for concrete surfaces over a coat of acrylic polymer primer. The coating to be applied on surface shall be liquid applied highly durable waterproof coating system for surface , based on high quality acrylic emulsion, functional filler, sunlight stable pigment and quality fungicides. It shall have properties that provide features like crack bridging ability, breathability, flexibility & exterior durability and resists micro-organism growth.It shall cover hairline cracks up to 0.5 mm effectively. It shall have excellent crack bridging ability and shall bridge cracks up to 2 mm width. The elongation at break is approx. 220 %. The tensile strength is 0.7 Mpa. It has a hardness shore ‘A’ scale of 80, with an adhesion strength of 3.4 Mpa. The coating is UV resistant, algae and fungus resistant, and has a water vapor permeability of 40 gm/m²/day and a crack bridging ability of 1-2 mm. The coating must be applied with temperature above 5°C and below 45°C. The coating shall be applied in two coats of by roller or brush application at the interval of 4-6 hours.Allow applied coating to dry or cure for 7 days , complete all specified and directed by Engineer-in-charge.
100
-
-
... More
M&L for repairs to damaged surface of RCC elements like beams, columns, wall by removing all loose cement plaster/concrete, providing and laying of micro-concrete more than 20mm thickness (Average) by using the recommended water powder ratio mix the micro-concrete with pan mixer as per manufacturer's instruction including water tight shuttering necessary curing for 7 days all as specified and directed by Engineer - in - Charge.
Note : Micro concrete will be measured and paid separately.
300
-
-
... More
Providing and placing in position micro-concrete, grade M40, which shall be cement based prepacked single component, chloride free, non-shrink, free flow, self compacting, ready to use after mixing water in specified proportion, obtained from Fosroc / SIKA / BASF/ Dr Fixit, thickness of section upto 75 mm all as specified and as directed by the Engineer in charge (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument) NOTE - [a] The rate quoted for respective items shall be deemed to be inclusive of all material, labour, expert supervision, Tools, Plant, Safety measures like safety belts, ropes, helmets, netting etc. required to work upto G+ 1 floor height as per site requirement and providing double scaffolding and as required and removal of the same on completion of the repairs and disposal and depositing the demolished material outside MD land complete all as specified and as directed.
[b] The Structural repair works shall be got executed directly by the Manufacturer or through their authorised applicator
4
-
-
... More
M&L for preparation of surface of reinforced bar by applying rust remover and then applying a coat of epoxy zinc primer on exposed reinforced surface all as specified and directed. Note : Surface area for concrete shall be measured for payment purpose.
300
-
-
... More
S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.
200
-
-
... More
S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.
100
-
-
... More
Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcement as required to facilitate demolition, complete all as specified.
5
-
-
... More
Material and labour for repair to RCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in chajjas, beams or columns etc upto double storey bldgs including necessary formwork complete all as specified and directed.
5
-
-
... More
Demolition cement concrete in any position not other wise specifically provided for
23
-
-
... More
Material and Labour for PCC 1:2:4 type B-0 using (12.5 mm graded stone aggregate) as in padding on roof top including WPC as per manufacturers instructions to achieve the slop required, with minimum thickness of 25mm consolidated and finished even and fair without using extra cement. (WPC shall be measured and paid separately
23
-
-
... More
M&L for 10 mm thick screed bed or bedding layer in CM 1:3 mixed with water proofing compound as per manufacturer instructions on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and directed.
920
-
-
... More
M&L for Providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing memberane comprising of the following for Non Approachable roofs :-
-
-
-
... More
(a) Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.30 kg/Sqm on top of dry surface of finished cement mortar plaster.
920
-
-
... More
(b) One coat of hot blown bitumen of grade 85/25 @ 1.2kg /sqm shall be applied over primed surfaces.
920
-
-
... More
(c) One layer of polymeric water proofing membrane of 3mm thickness and weight not less than 3 kg/Sqm consisting 90 micron thicken of central core shall be unrolled surfaces with lap of 100 mm and the over lap shall be sealed by flame.
920
-
-
... More
(d) Applying two coats of aluminum paint on top of membrane @ 0.10Kg/Sqm.
920
-
-
... More
Taking down cement plaster from brick walls/stone masonry walls, concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed.
810
-
-
... More
Material and labour for 15mm thick rendering in cement mortar (1:6) on brick/stone masonry or concrete surfaces (internal walls) of any description, finished the surface even and smooth without using extra cement complete all as specified.
210
-
-
... More
Material and Labour for 15mm thick rendering on fair faces of brick work/stone masonry, concrete surfaces (external walls) or stone walls upto tripple storey bldgs in cement mortar 1:4 mixed with liquid water proofing compound using as per manufacturer’s instructions, finished even and fair, complete all as specified. Note : (i) WPC shall be measured and paid separately. (ii) Rendering upto 9 mtr ht shall be included in the quoted rate).
350
-
-
... More
Material and labour 10 mm thick cement plaster in cement mortar 1:3 on ceiling, finished even and smooth without using extra cement all as specified and directed.
250
-
-
... More
M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty, complete all as specified and directed.
210
-
-
... More
Material & Labour for preparation of new plastered surfaces of wall and applying two coats of weather coat over a coat of 1 mm thick wall care putty for neat and smooth finishing complete all as specified.
350
-
-
... More
Material & Labour for preparing new plastered surfaces and applying two coats of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty on ceiling complete all as specified and directed.
250
-
-
... More
M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper (acrylic) white or tinted over a coat of priming over a coat of 1 mm thick wall care putty on walls upto tripple storeys bldg complete all as specified and directed.
1850
-
-
... More
M&L for preparation of old plastered or un-plastered surface applying Two or more coats of 100% Premium acrylic emulsion paint (Weather Proof Paint) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.
260
-
-
... More
Material and labour for preparation of old Plastered or un-plastered surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty complete all as specified.
1275
-
-
... More
M&L for preparation of old painted surfaces of wood and wood based surfaces of any description, over 10cm in width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.
80
-
-
... More
M&L for preparation of old painted steel surface of any description, over 10cm in width or girth not other wise described and applying one coat of synthetic enamel paint complete all as specified and directed.
65
-
-
... More
M&L for two coat of synthetic enamel painting to new wood surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of pink primer complete all as specified and directed.
100
-
-
... More
M&L for two coat of synthetic enamel painting to new steel surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of red oxide primer complete all as specified and directed.
50
-
-
... More
M&L for 10mm thick rendering on concrete surfaces of roof projection cornices & chajja etc finished fair and even without using extra cement including WPC in CM 1:4 incl taking down existing cement plaster and including necessary arrangements to work on roof projection, cornice & chajja etc.
50
-
-
... More
Supply & fixed 50mm bore LDPE (Low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floors including taking down of old GI tubing, 40 mm bore all as specified and directed.
4
-
-
... More
Supply & fixed Polymer coloured (Polypropeylene Delrin and ABS) low level flushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet ball valve float valve bends brackets, rawl plug, brass screws handle etc complete having BIS derscription mark with 2731 with and including suitable size of MS brackets, plug, screws all as required incl taking down existing high level/low level flushing cistern any type disconnecting pipes and jointing with new one etc and making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with Water closet of any type complete all as specified and directed.
16
-
-
... More
Supply and fixing in repairs Vitreous China W.H.B. white oval type counter below type of size 570 x 445 mm including waste coupling, waste pipe and brackets etc. complete all as specified.
16
-
-
... More
Supply and fixing , vitreous China squatting pan of Orrisa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including provision of lime concrete bedding, trap and connection to flush pipe complete all as specified.
12
-
-
... More
Supply and fixing in repairs vitreous china premium quality/1st quality wash down water closet pan (pedestal pattern), white (excluding flushing cistern & flush pipe) & incl 01 No ‘P’ or ‘S’ trap of dia 100mm including provn of lime concrete bedding, complete all as specified.
4
-
-
... More
Supply & fixed in repair Vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified.
8
-
-
... More
Supply and fixing in repairs, Urinal spreader of Brass chromium plated for fixing with 15 mm dia pipe., compete all as specified.
8
-
-
... More
Supply and fixing in repairs,15mm bore pillar tap, fancy type, chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks , compete all as specified.
16
-
-
... More
Supply and fixing in repair, bib tap screwed down high pressure, cast copper alloy,fancy type, ISI marked, with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified.
32
-
-
... More
Supply and fixing (in repair) angle cock 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified. (Note : Weight of cock shall not be less than 0.575kg)
40
-
-
... More
Supply & fixed in repair PVC connections 45cm long including 15mm bore PTMT nuts on both ends complete all as specified.
40
-
-
... More
S&F in repair 15mm bore concealed stop valve type chromium plated cast copper alloy screwed down high pressure screwed both ends for iron pipe or for union all as specified and directed by Engr-in-charge.
10
-
-
... More
S&F in repair brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges all as specified and directed by Engr-in-charge.
10
-
-
... More
Supply and Fixing in repair rotational molded polyethylene water storage tanks white tripple layered (cylindrical vertical with closed top) capacity 1000 Ltr hoisted and fixed in position all as specified and directed by Engr-in-charge.
8
-
-
... More
S & F in repair gun metal globe/gate valves, with iron wheel head, screwed both ends for iron pipe flange ends type fixed of 20mm dia all as spd and directed.
8
-
-
... More
S&F in repair PTMT float ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipes all as specified and directed by Engr-in-charge.
8
-
-
... More
Supply and fixing 1500 mm x 600 mm beveled edge mirror of selected quality glass mounted on 5.5 to 6 mm thick PVC sheet board & decorative teakwood beading all around including polishing and fixed to wooden plugs with CP brass screws and cup washers.
4
-
-
... More
Taking up or down steel tubing and connections of 15mm bore including cleaning for refixing or removal to store provision for branch connection by inserting tee union elbow etc. complete all as required at site.
125
-
-
... More
All as item 95.00 here-in-above but 20mm bore, complete all as specified.
40
-
-
... More
Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 16mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor to the entire satisfaction of Engineer-in-charge.
125
-
-
... More
Refixing old steel tubing of 20mm bore and connections in new or old position (Walls, ceiling, floors, etc.
40
-
-
... More
Supply & fixed in repairs stainless steel grating openable 100mm dia without hole including fixing with white cement complete all as specified.
8
-
-
... More
Supply & fixed in repairs stainless steel grating openable 100mm dia with hole including fixing with white cement complete all as specified.
16
-
-
... More
Supply & fixed in repair fancy type shower rose125mm dia size of Rim and 30cm long CP brass pipe with swiwel joint complete all as specified.
8
-
-
... More
Supply & fixed in repair glass shelf assembly consisting of made out of 5.5 mm thick glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.
8
-
-
... More
S & F for CP brass Soap Dish Holder, complete all as specified and as directed.
12
-
-
... More
Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out complete all as specified and directed.
90
-
-
... More
S&F 110mm dia UPVC (SWR) type 'B' pipe single sockets in any length with rubber ring joints, laid in trenches or in floor complete all specified and directed.
25
-
-
... More
S&F 110mm dia UPVC (SWR) type 'B' pipe single sockets in any length with rubber ring joints, fixed to wall complete all specified and directed.
30
-
-
... More
S&F 75mm dia UPVC (SWR) type 'B' pipe single sockets in any length with rubber ring joints, laid in trenches or in floor complete all specified and directed.
35
-
-
... More
S&F 110mm dia UPVC (SWR) bends any radius including cutting of holes.
13
-
-
... More
S&F 75mm dia UPVC (SWR) bends any radius including cutting of holes.
10
-
-
... More
S&F 110mm dia UPVC (SWR) branch piece single (single 'Y') equal or unequal.
5
-
-
... More
S&F 75mm dia UPVC (SWR) branch piece single (single 'Y') equal or unequal.
5
-
-
... More
S&F 75mm dia UPVC (SWR) floor trap, plain with grating including jointing with solvant cement complete all specified and directed.
8
-
-
... More
S&F 75mm dia UPVC (SWR) multi floor trap, with grating including jointing with solvant cement complete all specified and directed.
8
-
-
... More
S&F UPVC (SWR) gully trap 125/110 mm setting and jointing with solvant cement complete all as specified and directed.
6
-
-
... More
S&F UPVC (SWR) vent cowl 110 mm bore setting and jointing complete all as specified and directed.
8
-
-
... More
Taking down old unserviceable copper/aluminium point wiring (light, fan, socket or power) complete including fittings and fixtures such as switches, ceiling rose, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc. all as directed by Engr-in-charge.
268
-
-
... More
M&L for point wiring with 1.5 Sqmm multistranded,1100 volt grade copper conductor cable of PVC insulated, FRLS and unsheathed type alongwith 1.5 Sqmm PVC insulated stranded copper conductor cable for continous earthing in & including PVC rigid conduit concealed on stone/brick masonry wall surface with accessories having ISI mark fixed on wall surfaces / ceiling including provision of PVC box of appropriate size for fixing switches sockets etc. all as specified for One light point / Fan/ bell point controlled by one switch.
-
-
-
... More
(a) One light point controlled by one switch with cables 1.5 sqmm size.
128
-
-
... More
(b) One fan/ exhaust fan point controlled by one switch with cables 1.5 sqmm size. .
34
-
-
... More
(c) One 3 pin socket outlet, 5 amps on the same board with other switches, with cables 1.5 sqmm size.
34
-
-
... More
(d)One light point controlled by two 2 - way switches, with cables 1.5 sq.mm size.
12
-
-
... More
(e) One 3 Pin socket oulet 5Amps on indepndent, with cables 1.5 Sqmm size
52
-
-
... More
(f) One 3 Pin 15A pin socket oulet 15Amps on indepndent board with cables 4 Sqmm size
8
-
-
... More
S&F switch piano flush type single pole one way 5/6 Amps.
248
-
-
... More
S&F socket outlet 5 pin 5/6 Amps flush type multipurpose suitable for 3 pin/2 pin plug complete including dismantling old one.
86
-
-
... More
S&F of switch piano 15 Amp 230 Volt, flush button single pole one way complete all as specified and directed by Engr-in-Charge including dismantling old one.
8
-
-
... More
S&F socket outlet 2 in 1, 3 pin 5/6 Amps and 3 pin 15/16 Amps flush type including old one.
8
-
-
... More
S&F ceiling rose surface type 3 terminals to be fixed on PVC block including dismantling old one.
162
-
-
... More
S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd.
34
-
-
... More
S&F switch piano flush type single pole 16 Amp 2 way
24
-
-
... More
S&F LED integrated batten tube light fittings 20W 4 Feet long complete up with twin core twisted flexible copper conductor cable of size 23/0.0076 complete all as specfied and directed.
116
-
-
... More
Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.
12
-
-
... More
M&L MCB TPN DB comprising of sheet metal enclosure double door suitable for mounting MCB 415 Volts 4 way including dismantling old one.
1
-
-
... More
M&L MCB SPN DB comprising of sheet metal enclosure single door suitable for mounting MCB 240 Volts with busbar 200 amps rated 8 way including dismantling old one.
6
-
-
... More
M&L MCB SPN DB comprising of sheet metal enclosure single door suitable for mounting MCB 240 Volts with busbar 200 amps rated 4 way including dismantling old one.
2
-
-
... More
S&F MCB TP - 63 Amps 415V 10KA 'B' curve miniature circuit breaker (MCB) and current carrying capacity in the DB complete with connection testing and commissioning.
1
-
-
... More
S&F RCBOs Double pole, 30mA 32 Amp rating for earth leakage, overload & short-circuit protection.
8
-
-
... More
Supply and fixing SPN 32 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.
8
-
-
... More
Supply and fixing SP 6 to 32 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.
16
-
-
... More
Taking down carefully, deposited to MES store and hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specfied and directed.
34
-
-
... More
S&F exhaust fans AC single phase 240 Volts of size 300 mm sweep with louver and complete accessories including making hole with suitable size for Exhaust fan, after completer of work, finishing with cement and plastering and repainting with existing color all as specified and directed by Engr-in-Charge.
4
-
-
... More
Material & labour for earthing complete with galvanised steel earth plate electrode 60x60cmx6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below the ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level, connected to galvanised earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or of steel all as shown in electrical plate No 3 of SSR part-I 2009 connected to main switch board all as specified and testing on completion including. Necessary excavation, earthwork, PCC works and CI earth pit cover with watering pipe 20mm dia GI pipe medium grade, funnel with wire mesh and lugs and GI pipe 15 mm dia of light grade, for protection of earth lead complete all as specified and directed.
1
-
-
... More
Excavating in trenches n.exc 1.5 m width and n.exc 1.5m in depth for taking out cable and cable cover and getting out in any type of soil
13.5
-
-
... More
Returning, filling in, including spreading levelling, watering and well ramming in layers n.exc 25 Cm.
8.62
-
-
... More
Removing excavated materials n.exc 50 mtr depositing where directed at a level n.exc 1.5 m above the starting point
4.88
-
-
... More
M&L for spreading, levelling in layers n exc. 25 cm thick and ramming of sand cushioning to PVC/ XLPE cables with tibba sand and punning to provide required cover to UG cables.
Note :- For the purpose of payment only punned thickness will be measured.
3.65
-
-
... More
Supply and laying reinforced precast concrete cable cover, class LV, type 1 flat, 250mm x 150mm x 40mm.
348
-
-
... More
Material & labour for taking out old GI Pipe 50mm dia from trenches and removing from site
12
-
-
... More
Supply and fix medium grade 50 mm dia GI pipe fix complete to wall , poles etc with suitable clamp for protection of cable complete all as directed.
12
-
-
... More
Supply, laying and testing cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of size 35 sq mm 3.5 core.
95
-
-
... More
S&F Submain wiring alongwith earth wire with the following sizes of 2x2.5 sqmm + 1x2.5sqmm earth wire FR PVC insulated copper conductor, single core cable in surface/recessed as required.
Note : Two run of 2.5 sqmm cable with colour code of R, Y & B for phase/ neutral and one run of same size cable with Green colour as earthing for socket point alongwith required PVC conduit and connected items will be measure as one RM.
450
-
-
... More
S&F Submain wiring alongwith earth wire with the following sizes of 2x4.0 sqmm + 1x4.0 sqmm earth wire FR PVC insulated copper conductor, single core cable in surface/recessed as required.
Note : Two run of 4.0 sqmm cable with colour code of R, Y & B for phase/ neutral and one run of same size cable with Green colour as earthing for socket point alongwith required PVC conduit and connected items will be measure as one RM.
350
-
-
... More
S&F LED security light luminaries of 20 watt for energy saving having IP-65 degree of protection made of pressure die cast aluminum housing and heat resistant thoughned glass with excellent thermal management, LED's should have better optics and uniform distribution of light including GI tubing 40mm dia light grade 1.2 mtr long pipe bent to shape 120 degree for mounting of security light and fixed to wall/pole, with suitable MS clamps 2 Nos with nut and bolt and washers including connecting complete including 2.5 sqmm stranded copper conductor of suitable length as per direction and approved by Engr-in-charge,
6
-
-
... More
Taking down old Sheet metal enclouser and supply and fix new sheet metal enclouser cubical type factory fabricated made out of 1.6 mm thick CRCA sheet with front side openable single door system powder coated painted to shade RAL 7032, PL Gasket, hinged single door ,IP-55 mounting plate made out of 2mm thick CRCA sheet steel and earth bolts etc. of size 4000x4000x200mm and making good finishes around the DB with cement and paint with existing colour all as speceified & directed by Engr-in- charge. Note :-- Cost of any minor modification if required in fixing of the sheet metal enclouser as per site requirement and making good the disturbed surfaces matching with existing finish, will be deemed to be included in the cost of this item.
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%