Military Engineer Services Tender

Under-voltage Release 230 V AC

Closing Preventer 415V AC

Supply only Jaw contact Assy. 630/1000A S1

Supply only Jaw contact Assy. 800/1000A C/H & 1250A S1

Supply only Jaw contact Assy. 1250/1600A C/H, 1600/2000A S1

Supply only Pole Assy. 630-1250 S1 D/O

Supply only Pole Assy. 1250/1600 C & 1600 S1 D/O

Taking out old underground LT Cable of size 10 sqmm to 120 Sqmm of 3.5 core from LT Panels trenches/floors /road/wall/ pipe/pole/including taking out loop from trenches upto 1.5 mtrs depth, cutting the faulty end of cable and refixing the cable in original position by using flat aluminium sockets/ thimble/ and insulating the all nacked wires of any size including making connection with MCCB's/ Switches complete all as directed by Engineer-in-Charge. Note : Exacavation for taking out LT cable from will measured and paid separatly.

All as per item No. 11 here-in-before but 150 Sqmm to 630 Sqmm 3.5 core

Excavation in trenches not exceeding 1.5 mtr wide, and not exceeding 1.5 mtr in depth; for laying of cables, pipes in soft/loose soil etc and not exceeding 10 Sqm on plan and getting out including trimming of sides complete all as specified and directed by Engineer-in-Charge

Returning filling in, including spreading , levelling, watering and well ramming in layers each not exceeding 25cm in soft/loose soil complete all as specified.

Removing surplus spoil to distance not exceeding 50metre and depositing where directed at level not exceeding 1.5metre above the starting point complete all as specified.

Supply and laying un-reinforce precast concrete cable cover, class LV type-1 size 250 mm X150 mmx 40mm for protection of cable complete all as specified and directed by Engineer-in-Charge

Local tibba dry sand cushioning and cover (8 cm thick layer of sand before laying of cable and 15 cm thick layer of sand after laying of cable) for protection of cable, material and labour complete all as specified and as directed by Engineer-in-Charge.

Dis connecting the main LT panel at OTM and MD accn of any size and Cap and repair of complete panel by taking out the cable ,Bus -bar , Voltmtr , Amp mtr ,including wiring and other minor parts, cleaning the complete accessories carefully. Minor repairs shall be rectified Parts/accessories shall be cleaned properly and refixing the parts at its original locations, checking and repair of the internal panel wiring with suitable size of wire and remove the carbon deposited inside the contact, cleaning all other spare parts all as directed by the Engineer-in-charge and reassembled after repair/replacement of following parts.

Supply and fixing in replacement Cable indoor/outdoor end terminal jointing kit for LV/LT 1100 V cable heat shrinkable type joint kit complete with jointing material, 04 Nos coloured sleeves(Red, Blue, Yellow and black) each 45 cm long and accessories thimbles etc suitable for 25 sqmm to 50 sqmm 3.5 core XLPE armoured aluminium conductor cable including testing after jointing fixing in replcement complete all as specified and as directed by Engineer- in - charge.

Ditto All as per Srl Item No.19 Here in above but 70 Sqmm to 150 sqmm 3.5 core

Ditto All as per Srl Item No.19 Here in above but 185 Sqmm to 300 sqmm 3.5 core

Ditto All as per Srl Item No.19 Here in above but 400 Sqmm 3.5 core

Ditto All as per Srl Item No.19 Here in above but 500 Sqmm 3.5 core

Ditto All as per Srl Item No.19 Here in above but 630 Sqmm 3.5 core

Supply and fixing in replacement Cable jointing kit for LV/LT 1100 V cable for straight through , heat shrinkable type joint kit complete with jointing material and accessories suitable for 25 Sqmm to 50 Sqmm 3.5 core XLPE armoured aluminium conductor cable including testing after jointing, fixing in replacement complete all as specified as directed by Engineer-in-Charge.

Ditto All as per Srl item No 25 here in above but 70 Sqmm to 150 sqmm 3.5 Core

Ditto All as per Srl item No 25 here in above but 185 Sqmm to 300 sqmm 3.5 Core

Supply and fixing in replacement Cross linked poly-ethylene (XLPE) insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables ( heavy duty) with stranded aluminium conductor, 1100 volts LT grade of cross-sectional area 10 Sqmm 02 core laid in trenches/through pipe in road crossings/ paths /drains /ducts /floors /along poles/walls/ceilings/ equipments etc supplied, fixed/ laid in repair including commissioning and testing complete all as specified and as directed by Engineer-in-Charge.(Note: :- (i) Necessary excavation and earth work, brick protection, sand cushioning and cover and GI pipe shall be measured and paid for separately.(ii) Road manually cutting/floor cutting/cutting holes etc in wall required for laying /fixing of cable etc shall be made good as per existing site condition. Nothing extra shall be admissible on this account and quoted rate for this item shall be deemed to include for the same) Make : /Havells/Finolex/Polycab

Ditto All as per Srl item No 28 here in above but size of cable 16 Sqmm 4 core

Ditto All as per Srl item No 28 here in above but size of cable 25 Sqmm 4 core

Ditto All as per Srl item No 28 here in above but size of cable 35 Sqmm 3.5 core

Ditto All as per Srl item No 28 here in above but size of cable 50 Sqmm 3.5 core

Ditto All as per Srl item No 28 here in above but size of cable 95 Sqmm 3.5 core

Supply and fixing in replacement GI pipe light grade 40 mm bore (ISI marked) laid in trenches/ road crossings/ fixed to poles/ceiling / along walls/ path /drain/floors with and including all necessary clamps, nuts, bolts, washers etc and all fittings as required, complete all as specified and as directed by the Engineer-in-Charge. (Note :- Necessary excavation, earth work and same work shall be measured and paid for separately.)

Ditto All as per Srl item No 34 here in above but dia of pipe 50 mm

Boring of holes under road 100 mm dia, pavement, hard standing by trench less technology(manually) with out disturbing the top surface of roads for laying of cables/GI pipes complete all as specified and as directed by the Engineer-in-Charge.

Taking out old LT underground cable from trench depth upto 1.5 mtrs and laying after removing of defects any type/size laid in trenches including testing complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement shutters made out of 3.15.00 mm thick mild steel sheet, bent to shape, including taking out old damaged unservicable shutter complete with hinges, handle etc. complete all as directed by Engineer-in-Charge.

Supply and fixing in replacement mild steel medium weight Butt Hinges 100 mm long and fixed with steel screws complete all as specified.

Supply and fixing in replacement mild steel medium weight Butt Hinges 75 mm long and fixed with steel screws complete all as specified.

Supply and fixing in replacement mild steel pressed handles, size 75mm,complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement mild steel pressed handles, size 100 mm,complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement digital type tree phase Ampere meter range 0–400/300/200 Amps, with built in selector switch including CTs with proper ratio, square type, flush mounted including making connection with copper conductor cable of suitable size complete all as specified and as directed by Engineer-in-charge. Make L&T/havells/C&S

Supply and fixing in replacement digital type Volt meter with built in selector switch, range 50 – 520 volts, square type, flush mounted , accuracy class 1.0, Aux supply 80-300 VAC, CT seconday site selectable 1A/5A, CT/PT programmable frequency including making connection with copper conductor cable of suitable size complete all as specified and as directed by Engineer-in-charge. Make L&T/C&S/havells

Supply and fixing in replacement indicator lamp in diffrent colour code LED/Neon type complete (RYBW) including wiring with copper conductor cable of suitable size complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement Aluminium bus bar of any size with aluminium thimbles nuts, bolts, washers etc complete all as specified and as directed by Engineer-in-charge Note- Aluminium bus bar strips shall be covered with PVC insulation tape of red , yellow, blue and black colour for proper colour coding as per IE rules. Cost of nuts ,bolts, washers, insulation etc. shall be inclusive in the quoted rates.

Supply and fixing in replacement Bakelite sheet 10 mm thick, ISI marked complete all as specified and as directed by Engineer-in-charge.

Material & labour wiring with PVC insulated stranded copper conductor cable 4.00 sqmm complete all as specified and as directed by Engineer-in-charge.

Material & labour wiring with PVC insulated stranded copper conductor cable PVC wire 6 Sqmm single core copper conductor complete all as specified and as directed by Engineer-in-charge.

Material & labour wiring with PVC insulated stranded copper conductor cable 16 sqmm single core complete including suitable size of Luxes/thimble all as specified and as directed by Engineer-in-charge.

Cleaning and preparation of old painted surface of LT panel board complete and spray painting with two coat of synthetic enamel paint with appoved paint all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement MCCB, 63 Amps, 4 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and fast tripping mechanism Adjustable type complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified. Make :- Havells/L&T/legrand

Supply and fixing in replacement MCCB, 100 Amps, 4 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and fast tripping mechanism Adjustable typecomplete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.Make :- Havells/L&T/legrand

Supply and fixing in replacement MCCB, 160 Amps, 4 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and fast tripping mechanism Adjustable typecomplete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.

Supply and fixing in replacement MCCB, 200 Amps, 4 pole, 415 Volts, rupturing capacity not less than 36 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and fast tripping mechanism Adjustable type complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.Make :- Havells/L&T/legrand

Supply and fixing in replacement MCCB, 320 Amps, 4 pole, 415 Volts, rupturing capacity not less than 36 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and double break fast tripping mechanism Adjustable type complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.Make :- Havells/L&T/legrand

Supply and fixing in replacement MCCB, 400 Amps, 4 pole, 415 Volts, rupturing capacity not less than 36 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and fast tripping mechanism Adjustable type complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.Make :- Havells/L&T/legrand

Supply and fixing in replacement MCCB, 630 Amps, 4 pole, 415 Volts, rupturing capacity not less than 50 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and fast tripping mechanism Adjustable type complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.Make :- Havells/L&T/legrand

Repair of manual operated PF control panel / micro processor based automatic power factor control panel capacity of 21 KVAR to 500 KVAR fixed on various locations including testing, checking and repair and after removing deposited dust/seals/sludge and including taking out burnt/defective items and after fixing required necessary new items ie capacitor, MCBs, circuit wiring etc all as directed by Engr-in-Chaerge.

Supply only MPP type heavy duty power factor improvement capacitor (H/D ) with connector suitable for indoor/out door operation and provided with discharge resistors of rated voltage 440 v 50 HZ 3 phase with delta connection of rating 1 KVAR to 35 KVAR all as specified.

Supply only Push botton switch 6 A capacity 240 volts Make RAAS/Alfa/ Veeco

Supply only Miniature circuit breaker triple pole 63 Amp (C curve) 10 KA of capacity

Supply and fixing in replacement MCCB, 63 Amps, 3 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and fast tripping mechanism complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.Make :- Havells/L&T/legrand /ABB

Supply and fixing in replacement MCCB, 100 Amps, 3 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and fast tripping mechanism complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.Make :- Havells/L&T/legrand/ABB

Supply and fixing in replacement MCCB, 125 Amps, 3 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and fast tripping mechanism complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.Make :- Havells/L&T/legrand/ABB

Supply and fixing in replacement MCCB, 200 Amps, 3 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and ast tripping mechanism complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.Make :- Havells/L&T/legrand/ABB

Supply and fixing in replacement LT current transformers of capacity 100/5,200/5,300/5,500/5, Amps Make Alfa/ AE/ Veeco

Supply and fixing in replacement 4 pole contactor AC operated with main circuit bars of capacity 200 Amps at 415 Volts and operating voltage up to 600 V UL having main contact arrangement 4 NO+0 NC contacts Make :- ABB catpart NO. AF140-40-00 or equivalent make of L&T and Havells as per existing one. complete all as specified and directed by engr-in-charge.

Supply and fixing in replacement 4 pole contactor AC operated with main circuit bars of capacity 400 Amps at 415 Volts and operating voltage up to 600 V UL having main contact arrangement 4 NO+0 NC contacts Make :- ABB catpart NO. AF265-40-00 or equivalent make of L&T and Havells as per existing one. complete all as specified and directed by engr-in-charge.

Supply and fixing in replacement Three pole contactor AC operated with main circuit bars of capacity 250 Amps at 415 Volts and operating voltage up to 600 V UL having main contact arrangement 2 NO+2 NC contacts Make :- L&Tcatpart NO. MNX-250 series cat no. CS94141 or equivalent make of ABB and Havells as per existing one. complete all as specified and directed by engr-in-charge.

Supply and fixing in replacement Three pole contactor AC operated with main circuit bars of capacity 250 Amps at 415 Volts and operating voltage up to 600 V UL having main contact arrangement 2 NO+2 NC contacts Make :- L&Tcatpart NO. MNX-140 series cat no.CS94138 or equivalent make of ABB and Havells as per existing one. complete all as specified and directed by engr-in-charge.

Supply and fixing in replacement Three pole contactor AC operated with main circuit bars of capacity 80 Amps at 415 Volts and operating voltage up to 600 V UL having main contact arrangement 1 NO+1 NC contacts Make :- ABB catpart NO.AX80-30-11 or equivalent make of ABB and Havells as per existing one. complete all as specified and directed by engr-in-charge.

Supply and fixing in replacement APFC Relay 12 stage with built in multifuction meter for basic, THD and energy with 1 CT/3 CT sensing Option, smart switching, auto setup, THD protection, dual target PF, RS 485 communication, remote monitiring software complete all as directed by Eng-in-charge

M & L for earthing complete with GI Earth Plate Electrode 600mm x 600mm x6mm, thick buried directly in ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below Normal Ground Level, connected to Galvanised iron earth strip 32X6 mm drawn through and including Galvanised Iron protection Pipe 40 mm bore (dia) Light grade upto heightl of the transformer foundation where foundation situated by means of Bolts, Nuts, Check Nuts and Washers etc Earth plate surrounded by a packed thickness of charcoal or coke dust mixed with common salt in alternate layers of not exc 150mm thick PCC Pit in cement concrete 1:3:6 (20 mm graded aggregrate ), Precast RCC 1:2:4 (20mm graded aggregrate ) cover slab 350 x350 x 50mm thick reinforced with and including 8mm dia TMT Bars @ 10 cm Centre to Centre both ways GI Wire Mesh , Funnel, with GI Watering Pipe 20mm bore dia Medium grade necessary excavation in soft loose soil returning filling in and removal of surplus soil upto a distance of 50 METRE and all as shown in Electrical Plate No. 3 of MES schedule Part- I and testing on completion complete all as specified and as directed.

Material and labour for rennovation and testing of earthing and submission of desired test reports as per direction of Engr-in-charge. Note :- material required for rennovation of earthing, earth pit, earth pit cover is deemed to be included in quoted rate.

Taking down carefully the defective street light fittings any kind any type from the poles/walls and refixing the same on poles/walls after repair complete all as directed by Engineer in Charge.( Note: A Team of workers for emergency are avlaible inside the camp for 24 Hours) 1. T&P i.e, ladder and vehicle will provided by the contractor.2. The contractor/his rep will collect the complaint from JE every day 9.00 hrs , the same will be rectified before sunset on same day,If the contractor fail to rectify the defect mentioned in the complaint slip on same day, he will be charged Rs 100/per complaint and same will be recovered from the contract amount. NOTE:- VMTL with driver will be provided by the AGE E/M for repair of double swan neck pole's and single swwan neck poles security lights only.

Supply and fixing in replacement outdoor Driver unit 25 watt with surge protection. Make –CG /Philps/Wipro

Supply and fixing in replacement outdoor Driver unit 40 watt with surge protection. Make –Make –CG /Philps/Wipro

Supply and fixing in replacement outdoor Driver unit 45 watt with surge protection. Make –Make –CG /Philps/Wipro

Supply and fixing in replacement outdoor Driver unit 75 watt with surge protection. Make –Make –CG /Philps/Wipro

Supply and fixing in replacement outdoor Driver unit 90 watt with surge protection. Make –Make –CG /Philps/Wipro

Supply and fixing in replacement outdoor Driver unit 150 watt with surge protection. Make –Make –CG /Philps/Wipro

Supply and fixing in replacement surge protection devices 5 KV compatible with industrial and outdoor LED fixtures upto rated power of 75 Watt Make –Make –CG /Philps/Wipro

Supply and fixing in replacement surge protection devices 5 KV compatible with industrial and outdoor LED fixtures with rated power above 75 Watt and upto 150 Watt Make –Make –CG /Philps/Wipro

Testing and checking of faulty street light feeder including under ground cable or on the pole on line etc and repair the same after remove the faulty feeder complete testing all as directed by Engineer in Charge Note :- Earth work measured and paid separately.

Taking down Unserviceable time switch , checking / testing Time switch by disconnecting the connection and refixing the same after minor repair/resetting all as directed by Engineer in Charge Note:- item required for repairing of timer switch will measured and pain seperately under appropriate schedule of item.

S & F MCB SP, 63 Amps , 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge. Make :- L&T/Havells/C&S

S & F MCB 4 pole , 63 Amps , 415 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge. Make :- L&T/Havells/C&S

Supply only Panel mounted 2 Pole contactor MNX-22-2P of suitable rating operational voltage 230 volts confirming to IS/IEC60947-4-1, AC 50 HZ, inbuilt aux. contacts- 1 No+01 NC with standard coil voltage 220 volts the surge resistor contract shall be post break type and damping resistances after closing be cut of current rating cap 22 Amp. Make :L&T/C&S/Havells

Supply only Panel mounted 2 Pole contactor MNX-40-2P of suitable rating operational voltage 230 volts confirming to IS/IEC60947-4-1, AC 50 HZ, inbuilt aux. contacts- 1 No+01 NC with standard coil voltage 220 volts the surge resistor contract shall be post break type and damping resistances after closing be cut of current rating cap 22 Amp. Make :L&T/C&S/Havells

Supply only nature switch designed for automatic control of outdoor lighting, using infrared sensing based nature switches compatible for both single & three phases supply with operating voltage range 120-440 Volts for a nominal 230 Volts system.complete all as specified and directed by engr-in-charge.

Material and Labour for repairing of MS street light junction box, tighting of loose nut, bolts, screws etc including cutting of burnt thimbles/ LT cable, taking out LT cable from Loop and recconecting to bus bar with new thimbles duly crimpped with cable complete all as directed and specified by Eng-in-charge.

Trimming /pruning of the tree branches coming around the street light fittings and making the street light free from touching the tree branches not less the 4 mtr radius complete all as directed and specified by Eng-in-charge.

Supply & fixing in replacement of LED decorative post top lantern light fittings for 360 degree indirect light with IP 65 protection, resistant to impact and corrosion, glare free and better uniformity. Make CG Model LPTO-40-CDL or equivalent Make Philips /Bajaj

Supply & fixing in replacement of LED post top lantern light fittings with IP 65 protection, ideal to lit up parks, garden ways etc. Make CG Model LPTH-20-CDL or equivalent Make Philips /Bajaj

Supply & fixing in replacement of LED Bollard light fittings with IP 65 protection, Innovative design with uniformly lit diffuser at the upper portion acts a beacon of path guidance in a landscape environmen etc. Make Havells catpart No.CONENXGLS8WLEDPSYM830TOPC or Equivallent make of Philips /Bajaj

Suppy and Fixing LED based street light, housing made up of LM6 pressure die cast aluminium alloy with aerodynamically designed for all weather conditions with excellent thermal management, toughned glass and high power LED's with seconday optics and IP66 protection, sturdiness. The fixture should have a minimum system efficiency of more than 110/120 lumen/watt and a minimum system lumen output of not less than 7700 lumens and maximum system wattage 70 Watts. The fixture shall have a correlated colour temperature of al least 5700K and CRI minimum 70. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance ingress protection of IP66 (lamp and gear compartment and mechanical inpact resistance raiting of IK=08. The fixture driver should have an operating voltage range of 140-270 V & potted type for humming free operation, driver should be withstand up to 440v for 8hrs, two surge proection, 4KV one on driver and one 10 KV external surge protection, PF0.95 and THD10% and have double phase protection. LED light fitting should be suitable for ambient temperature from (-) 10C to (+) 50 C. The fixture should comply with the parameters IEC 60598 and LED should comply to IEC 61000-3-2 ed. 3.2 per harmonics IEC 61347-2-3,2006 in configuration with IEC 61347-1 ed 2.0,2007 for electrical safety LM 79 and for LED LM 80 test report needs to be submitted from the house NABL accreditation laboratory. Make CG Catpart No.TRP-409-70-57-SL-GL-NSG or equivalent make of Philips/Wipro NOTES FOR LED LIGHT FITTINGS : For item No. 43 to 51. (i) All LED light/luminare shall meet the provision laid down in IS - 16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part -II / Section 13. (ii) Contractor shall submit test report of LED street light fitting from Government accredited test laboratory for LM-79 and LM-80. (iii) Contractor has to furnish a replacement warranty of 02 years for LED light fittings complete including lamps from the date of completion of contract. The product will be replaced on site free of cost in the following case :- (a) Manufacturing defects. (b) Failure due to mechanical and electrical impact. (c) Drop in lumen (or lux at 1 m) below 90% of claimed values of lumen (or lux at 1 m) of the LED /Luminaries. (v) Driver of the fittings must be potted type only and both fixture and driver must have seprate BIS marked resistration with clearly mentioned on fixture as well as on driver. (iv) CA No. shall be embossed on each LED light fittings by printing mechanism as directed by engr-in-charge and rate of the same is deemed to be included in above quoted rate.

Suppy and Fixing LED based street light, housing made up of LM6 pressure die cast aluminium alloy with aerodynamically designed for all weather conditions with excellent thermal management, toughned glass and high power LED's with seconday optics and IP66 protection, sturdiness. The fixture should have a minimum system efficiency of more than 110/120 lumen/watt and a minimum system lumen output of not less than 6600 lumens and maximum system wattage 60 Watts. The fixture shall have a correlated colour temperature of al least 5700K and CRI minimum 70. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance ingress protection of IP66 (lamp and gear compartment and mechanical inpact resistance raiting of IK=08. The fixture driver should have an operating voltage range of 140-270 V & potted type for humming free operation, driver should be withstand up to 440v for 8hrs, two surge proection, one 4KV on driver internal and one 10 KV external surge protection, PF0.95 and THD10% and have double phase protection. LED light fitting should be suitable for ambient temperature from (-) 10C to (+) 50 C. The fixture should comply with the parameters IEC 60598 and LED should comply to IEC 61000-3-2 ed. 3.2 per harmonics IEC 61347-2-3,2006 in configuration with IEC 61347-1 ed 2.0,2007 for electrical safety LM 79 and for LED LM 80 test report needs to be submitted from the house NABL accreditation laboratory. Make CG Catpart No.CRP-409-60-57-SL-GL-NSG or equivalent make of Philips/Wipro

Suppy and Fixing LED based street light, housing made up of LM6 pressure die cast aluminium alloy with aerodynamically designed for all weather conditions with excellent thermal management, toughned glass and high power LED's with seconday optics and IP66 protection, sturdiness. The fixture should have a minimum system efficiency of more than 110/120 lumen/watt and a minimum system lumen output of not less than 4950 lumens and maximum system wattage 45 Watts. The fixture shall have a correlated colour temperature of al least 5700K and CRI f minimum 70. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance ingress protection of IP66 (lamp and gear compartment and mechanical inpact resistance raiting of IK=08. The fixture driver should have an operating voltage range of 140-270 V & potted type for humming free operation, driver should be withstand up to 440v for 8hrs, two surge proection, 4KV one on driver and one 10 KV external surge protection, PF0.95 and THD10% and have double phase protection. LED light fitting should be suitable for ambient temperature from (-) 10C to (+) 50 C. The fixture should comply with the parameters IEC 60598 and LED should comply to IEC 61000-3-2 ed. 3.2 per harmonics IEC 61347-2-3,2006 in configuration with IEC 61347-1 ed 2.0,2007 for electrical safety LM 79 and for LED LM 80 test report needs to be submitted from the house NABL accreditation laboratory. Make CG Catpart No.CRP-409-45-57-SL-GL-NSG or equivalent make of Philips/Wipro

Suppy and Fixing LED based street light, housing made up of LM6 pressure die cast aluminium alloy with aerodynamically designed for all weather conditions with excellent thermal management, toughned glass and high power LED's with seconday optics and IP66 protection, sturdiness. The fixture should have a minimum system efficiency of more than 125/135 lumen/watt and a minimum system lumen output of not less than 22500 lumens and maximum system wattage 180 Watts. The fixture shall have a correlated colour temperature of al least 5700K and CRI f minimum 70. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance ingress protection of IP66 (lamp and gear compartment and mechanical inpact resistance raiting of IK=08. The fixture driver should have an operating voltage range of 140-270 V & potted type for humming free operation, driver should be withstand up to 440v for 8hrs, two surge proection, 4KV one on driver and one 10 KV external surge protection, PF0.95 and THD10% and have double phase protection. LED light fitting should be suitable for ambient temperature from (-) 10C to (+) 50 C. The fixture should comply with the parameters IEC 60598 and LED should comply to IEC 61000-3-2 ed. 3.2 per harmonics IEC 61347-2-3,2006 in configuration with IEC 61347-1 ed 2.0,2007 for electrical safety LM 79 and for LED LM 80 test report needs to be submitted from the house NABL accreditation laboratory. Make CG Catpart No.CRP-418-180-57-HL2-GL-HR-NSR or equivalent make of Philips/Wipro

Suppy and Fixing LED based Flood light, housing made up of LM6 pressure die cast aluminium alloy with aerodynamically designed for all weather conditions with excellent thermal management, toughned glass and high power LED's with seconday optics and IP66 protection, sturdiness. The fixture should have a minimum system efficiency of more than 110/120 lumen/watt and a minimum system lumen output of not less than 22000 lumens and maximum system wattage 200 Watts. The fixture shall have a correlated colour temperature of al least 5700K and CRI f minimum 70. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance ingress protection of IP66 (lamp and gear compartment and mechanical inpact resistance raiting of IK=08. The fixture driver should have an operating voltage range of 140-270 V & potted type for humming free operation, driver should be withstand up to 440v for 8hrs, two surge proection, 4KV one on driver and one 10 KV external surge protection, PF0.95 and THD10% and have double phase protection. LED light fitting should be suitable for ambient temperature from (-) 10C to (+) 50 C. The fixture should comply with the parameters IEC 60598 and LED should comply to IEC 61000-3-2 ed. 3.2 per harmonics IEC 61347-2-3,2006 in configuration with IEC 61347-1 ed 2.0,2007 for electrical safety LM 79 and for LED LM 80 test report needs to be submitted from the house NABL accreditation laboratory. Make CG Catpart NoCFS-501-200-57-60D-SL-GL-NGG or equivalent make of Philips/Wipro

Supply & Fixing of LED based Flood light fitting, housing made up of pressure die cast aluminum Alloy with effective thermal management, sturdiness . The fixture should have a minimum system efficacy of more than 110 lumen/Watt and a minimum system lumen output of not less than 8800 lumens and maximum system wattage 80 Watts. The fixture shall have a corelated color temperature of at least 5000K and a CRI of minimum 70 .The fixture shall be designed for a system life of 50,000 hours @70% lumen maintenance. Ingress Protection of IP66 (lamp and gear Compartment and Mechanical Impact Resistance Rating of IK =05. The fixture driver should be withstand up to 440v for 8hrs, two surge proection not less than 5KV one on driver and one external surge protection, PF 0.95 and THD20% .The fixture should comply with the parameters as per IS10322 and for EMI and LM 79 test reports .Including suitable size street light fitting bracket with suitable size clamps,nut bolts and washers as per site requirement complete all as specified as directed by Engineer-in-Charge. make CG Catpart No.LFL-80-CDL/60-M or equivalent make of Philips/Wipro

Supplying and fixing of automatic street light switch using infrared sensor based Nture Switch-, 25 kw equally distributed, 63 Amps,3-pole, Model - Swadeep-02 EC 25 Kw3P for automatic switching of street lights based on LUX level of natural light . The sensor(Nature switch ) along with suitable power contactor rating 63 Amps 3- pole & 40 Amps 2-pole, MCB SP 63 Amps -03 nos and support terminals should be enclosed in pole/wall mountable enclosure made of rust proof ,electric shock proof, termite proof and FR grade SMC Junction box (Sintex make) confirming to IP54.The contactor suitable to 3- phase load of 25 kw , rating 63 amps 3pole, MCB rating 63 amps SP 03 NOS. Make of Nature switch-Kakatiya Energy systems Pvt Ltd.Hyderbad/ Bajaj/Healer.Contactor-BCH/L&T/Schneider (asper IEC-60947-4-1/IS-13947-4-1), MCB- Hager/ Schneider/ Legrand/L&T, Circuit Wiring-Polycab/RR Cable /Finolex.

Supplying and fixing of automatic street light switch using infrared sensor based Nture Switch, 08 kw equally distributed, 63 Amps,1-pole, Model - Swadeep-02 EC 8 Kw1P for automatic switching of street lights based on LUX level of natural light . The sensor(Nature switch ) along with suitable power contactor rating 63 Amps 2- pole & 40 Amps 2-pole, MCB SP 63 Amps -02 nos and support terminals should be enclosed in pole/wall mountable enclosure made of rust proof ,electric shock proof, termite proof and FR grade SMC Junction box (Sintex make) confirming to IP54.The contactor suitable to 1- phase load of 08 kw , rating 63 amps 2 pole, MCB rating 63 amps SP 01 NOS. Make of Nature switch-Kakatiya Energy systems Pvt Ltd.Hyderbad/ Bajaj/Healer.Contactor-BCH/L&T/Schneider (asper IEC-60947-4-1/IS-13947-4-1), MCB- Hager/ Schneider/ Legrand/L&T, Circuit Wiring-Polycab/RR Cable /Finolex.

S & F Junction Box fof size(H X W X D) 300x200x105 mm made out of Polycarbonate material totally enclosed, dust and vermin proof, rain protected slanted roof top, door pasted with rubber gasket, water tight IP 66 with integrated membranes/metric knockouts for cable entry with cable glands, protection and suitable size of "connectwell" stud teriminal (provision for socket bolting)- 04 Nos suitable for 415 volts, 50 Hz, 3 phase 4 wire internal wiring system including MCB SP 06 amps- 01 No and mounted on tubular/PCC pole with suitableclamps, nuts, bolts including removal of exiting unsv all as specified and directed. Note :- CA No. shall be embossed on each box by digital printing mechanism.

Supply and fixing in replacement of All -in-One Solar street light of 30 W made with High efficiency Mono crystalline Solar PV Module, Lithium Ferro Phosphate battery with in -built BMS techonology, High Efficacy LED, MPPT Solar charge controller and aluminium Extruded body & is specially programmed to automatically control the dimming and brightness of light complete all as specified and direcetd by Engr-in-charge. Make Havells Catpart No. SOLAR AIO 30W or equivallent make of CG/bajaj