Military Engineer Services Tender
If you're looking for Rajasthan tenders online and are tired of typing tender ID over and again or going through the cumbersome government websites for it, you are in luck. We have collated every Eproc Rajasthan tender on BidAssist. And for any queries related to an e-tender Rajasthan, like bidding process, registration process, etc., are explained below. Read on.
Costs
EMD
₹ 30,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_641843_1Bid Award Id
ViewTender No
86098/E8Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
Excavating in post holes in hard dense soil (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed
70
-
-
... More
M&L for PCC 1:3:6, type C-2 using 40 mm graded stone aggregate as in foundation filling or mass concrete complete all as specified and as directed.
16
-
-
... More
S&F for rolled mild steel work Fe 290 (Gde E-165 ) as in fencing posts with or without Y/U/Swan nek made of angle or other section, made to shape complete, welding, drilled for fixing for holding of barbed wire or concertina coil etc to be prepared for hanging or steel hanging fittings also fastening and fixing complete all as specified and directed by Engr-in-Charge
1800
-
-
... More
S&F Roof trusses (framed), trussed, purlins,rails etc and fastenings and heavy bracket
framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 290 Gde E-165 complete all as specified and as directed.
1500
-
-
... More
S&F for 1 mm thick Mild steel, plain, black sheet in wall cladding, steel gates, sign board and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required
30
-
-
... More
M&L for preparation of new concrete surfaces of any description over 10cm in width or girth not otherwise discribed, and applying two coats of synthetic enamel paint (ordinary tint) complete all as specified and as directed.
110
-
-
... More
Precast cement concrete 1:3:6 type C1 (Using 20 mm graded stone aggregate) block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6 complete all as specified including demolition and as directed by the Engr-in - Charge.
5
-
-
... More
M&L for Writing letters or figures (Block. Roman, Italic or Indian) n exc. 30 cm high with retro reflective HIP tape of Make-3M or equivalent complete all as specified and directed
250
-
-
... More
Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.
17
-
-
... More
M&L for 75 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregates as in sub base complete all as specified and as directed.
375
-
-
... More
M&L for stone aggregate of size not exceeding 63 mm deposited spread and levelled in layers not exceeding 15 cm to a true surface of broken stones for E/M installation complete all as specified and directed
35
-
-
... More
M&L for preparation of new concrete surfaces of any description over 10cm in width or girth not otherwise described, and applying two coats of synthetic enamel paint (ordinary tint) complete all as specified and as directed.
150
-
-
... More
Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed
375
-
-
... More
Dismantling of Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.
350
-
-
... More
S&F for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.
350
-
-
... More
Taking down cement plaster on block masonary or concrete surfaces including raking out joints, hacking for key ,scrubbing down with water etc. complete all as specified and as directed.
255
-
-
... More
M&L for 15 mm thick rendering in cement mortar 1:4 or fair faces of brick or cement concrete surfaces finished even and smooth without using extra cement complete all as specifed and as directed.
255
-
-
... More
M & L 75 mm thick plain cement concrete 1 : 3 : 6 type C1 (using 20 mm graded stone aggregate) as in plinth protection laid in pannels including necessary form work, finished even and smooth without using extra cement complete all as specified and as directed.
150
-
-
... More
M&L for preparation of New surfaces of wall, by applying 2-3 mm thick white cement base putty in patches as required and applying two coat of oil bound distemper complete all as specified and directed
255
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements