Military Engineer Services Tender
If you're looking for Rajasthan tenders online and are tired of typing tender ID over and again or going through the cumbersome government websites for it, you are in luck. We have collated every Eproc Rajasthan tender on BidAssist. And for any queries related to an e-tender Rajasthan, like bidding process, registration process, etc., are explained below. Read on.
Costs
EMD
₹ 12,72,500Document Cost
₹ 3,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2023_MES_629983_1Tender No
81217Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Provn of RCC framed structure building complete as shown in drawing for Plinth-platform of DG Set and CEC vide drg no CEAG/JSLR/AR/65/2023 SH 1/1 with shed, Steel trusses- plate girders, Ramp etc including structural designing complete all as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for MT complex vide drg no CEAG/JSLR/AR/66/2023 SH 1/1 including structural designing complete all as specified and as directed
1
-
-
Provn of structure complete as shown in drawing for Washing ramp vide drg no CEAG/JSLR/AR/67/2023 SH 1/1 including structural designing complete all as specified and as directed. Note: POL store shown in drawing shall be measured and paid seperately under following item
1
-
-
Provn of RCC framed structure building complete as shown in drawing for POL store with ramp vide drg no CEAG/JSLR/AR/67/2023 SH 1/1 including structural designing complete all as shown in drawings, as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for MT Garrage 'A' Vechicles Garrage with Apron, saucer drain etc, vide drg no CEAG/JSLR/AR/68/2023 SH 1/2 ,2/2 including structural designing complete all as shown in drawings, as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for Guard Room complex vide drg no CEAG/ JSLR/ AR / 69/ 2023 SH 1/1 including structural designing complete all as shown in drawings, as specified and as directed. Note: Armoury building shown in drawing shall be measured and paid seperately under following item
1
-
-
Provn of RCC framed structure building complete as shown in drawing for Armoury building vide drg no CEAG/ JSLR/ AR / 69/ 2023 SH 1/1 including structural designing complete all as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for MI Room vide drg no CEAG/ JSLR/ AR / 70/ 2023 SH 1/1 including structural designing complete all as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for Storage Complex with Ramp vide drg no CEAG/ JSLR/ AR / 71/ 2023 SH 1/3 to 3/3 including structural designing complete all as specified and as directed.
Note: LPG store shown in drawing shall be measured and paid seperately under following item
1
-
-
Provn of RCC framed structure building complete as shown in drawing for LPG store with Ramp vide drg no CEAG/ JSLR/ AR / 71/ 2023 SH 1/3 to 3/3 including structural designing complete all as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for POL Store with Ramp vide drg no CEAG/ JSLR/ AR / 71/ 2023 SH 1/3 to 3/3 including structural designing complete all as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for Radio Transmitter room vide drg no CEAG/ JSLR/ AR / 72/ 2023 SH 1/1 including structural designing complete all as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for UMO Complex vide drg no CEAG/ JSLR/ AR / 73/ 2023 SH 1/1 including structural designing complete all as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for Common cooking -Dining facility, vide drg no CEAG/ JSLR/ AR / 74/ 2023 SH 1/3 to 3/3 including structural designing complete all as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for Single living Double storey Accomodation (4 Officers) (G+1) with garrages vide drg no CEAG/ JSLR/ AR / 75/ 2023 SH 1/3 to 3/3 including structural designing complete all as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for Servant Quarter for Offrs (block of 3 nos) vide drg no CEAG/ JSLR/ AR / 76/ 2023 SH 1/1 including structural designing complete all as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for Single living Double storey Accomodation 08 WOs vide drg no CEAG/ JSLR/ AR / 77/ 2023 SH 1/3 to 3/3 including structural designing complete all as specified and as directed.
Note: Car - scooter garrage shown in drawing shall be measured and paid seperately under following item
1
-
-
Provn of RCC framed structure building complete as shown in drawing for Bock of 04 Car garrage & 04 Scooter shed for 08 WOs vide drg no CEAG/ JSLR/ AR / 77/ 2023 SH 1/3 to 3/3 including structural designing complete all as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for Single living ORs Accomodation (SGT/AIRMEN/DSC) (double storey), vide drg no CEAG/ JSLR/ AR / 78/ 2023 SH 1/6 to 6/6 including structural designing complete all as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for block of Single living NCsE Accn vide drg no CEAG/ JSLR/ AR / 79/ 2023 SH 1/1 including structural designing complete all as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for Watch Tower (G+1) vide drg no CEAG/ JSLR/ AR / 80/ 2023 SH 1/1 including structural designing complete all as specified and as directed.
2
-
-
Provn of RCC framed structure building complete as shown in drawing for RO Plant Building cum Pump house building vide drg no CEAG/ JSLR/ AR / 81/ 2023 SH 1/1 including structural designing complete all as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for Scooter shed for ORs 68 Nos vide drg no CEAG/ JSLR/ AR / 82/ 2023 SH 1/1 including structural designing complete all as specified and as directed.
1
-
-
Provn of RCC framed structure building complete as shown in drawing for POL Store vide drg no CEAG/ JSLR/ AR / 83/ 2023 SH 1/1 including structural designing complete all as specified and as directed.
1
-
-
SCHEDULE `A' PART - II are not prepriced by MES and prepriced rates indicates 0.0 under column 5 signified this fact only and are TO BE QUOTED BY THE CONTRACTOR. Bidders shall insert their lumpsum amount in the Green coloured field under Col-6 only.
(Structural design of Bldgs/structure covered under this schedule is already provided by department)
-
-
-
Provn of RCC Static water Tank of capacity 50,000 ltr complete all as shown in drawings as specified and as directed.
1
-
-
Provn of RCC Under ground Sump of capacity 50,000 ltr complete all as shown in drawings as specified and as directed.
1
-
-
Provn of Garbage bin complete all as shown in drawings as specified and as directed.
2
-
-
Provn of Fire point complete all as shown in drawings as specified and as directed.
9
-
-
NOTE: Schedule ‘A’ Part III to XII are under Ser No. 1.00 to 12.00 are Prepriced by MES. Bidders shall insert their lumpsum amount in the Green coloured field under Col-6 only.
-
-
-
Lump sum price worked out for Excavation & Earthwork as listed in Sch `A’ Part III
1
-
4943805.05
Lump sum price worked out for Internal Water Supply as listed in Sch `A’ Part IV
1
-
91133.77
Lump sum price worked out for Internal Electrification & Flame proof lighting as listed in Sch `A’ Part V
1
-
4374006.23
Lump sum price worked out for Road, Path, Culvert as listed in Sch `A’ Part VI
1
-
9960916.04
Lump sum price worked out for Sewage Disposal as listed in Sch `A’ Part VII
1
-
1413958.06
Lump sum price worked out for Area Drainage as listed in Sch `A’ Part VIII
1
-
3035621.36
Lump sum price worked out for Security Wall and Gate as listed in Sch `A’ Part IX
1
-
1269877.28
Lump sum price worked out for External Water Supply as listed in Sch `A’ Part X
1
-
859204.44
Lump sum price worked out for External Electrification as listed in Sch `A’ Part XI
1
-
6973812.32
Lump sum price worked out for Lightening Protection & Chemical Earthing as listed in Sch `A’ Part XII
1
-
279265.28
Lump sum price worked out for Refrigeration and Air Conditioning as listed in Sch `A’ Part XIII
1
-
1992927.5
Lump sum price worked out for Hot Water Supply as listed in Sch `A’ Part XIV
1
-
76096.54
SCHEDULE 'A' PART - XV is not prepriced by MES and prepriced rates indicates 0.0 under column 5 signified this fact only. Bidder shall insert their rates in Green filed under Col-6.
-
-
-
RO Plant
-
-
-
Supply and Fixing reverse Osmosis Plant of out put capacity of 150 Litres per hours
Pre-Treatment Section
Raw water Feed pump
Multigrade sand bed filter and Activated carbon filter pressure gauges to check differential pressure.
Fine Filtration & Reverse Osmosis Block
Micron filter
R.O. membrane
High pressure Moter pump
MS Skid with powder coating for mounting R.O. equipments and controls
Control Instruments
(a) Electrical Control Panel
Heavy Duty Contractor with Timer Design and Capacity
1
-
-
Assumptions:
No. of working days: 34 days
No of working hours: 05-6 hours
Inputs (Raw water Quality): Total Dissolved Solids: 1500 PPM
Output (Treated Water Quality): Total Dissolved Solids: 50-100
TECHNICAL SPECIFICATIONS
Approx Flow Rate:
Feed Water : 400 LPH
Treated Water : 150 LPH
Rejected Water : 250 LPH
The reject flow depends on input water quality
-
-
-
1. RAW WATER PUMP
Purpose To feed the Dual Media Filter at pressure more than bar, which is min. operating pressure for filter. Specifications
(a) MOC: CI
(b) Centrifugal Pump
(c) Flow Rate: 1000 liters per hour
(d) Head : 25 m
(e) Electrical: 230 V, single phase, 50 hz
(f) Cycle: 2900 rpm
(g) Make: CRI
(h) Quantity : 1 No
-
-
-
2. SAND AND CARBON MEDIA FILTER
Purpose To remove the total suspended solids, dirt, iron and reduce silt density index which can foul the membrane.
Specifications Vessel:
(a) Make: CLD
(b) Material of Construction: FRP 8x44
(c) Testing Pressure: 10 kg/cm2
(d) Opening : Top & Bottom only
(e) Quantity: 2 No
Valve:
(a) Make: Initiative / Standard/ Eqlt
(b) Material of Construction: Noryl
(c) Type: Multiport Single lever value
(d) Size: 15 mm
(e) Maximum Flow Rate: 1000 LPH
(f) Working Pressure: 2-4 Bar
-
-
-
Media:
Mixed bed sand media consisting of the following
(i) Gravel
(ii) Pebbles
(iii) Quartz Sand
(iv) Activated Carbon media
Average Porosity 50 micron particulate size
Bed depth: 600 mm
Pipelines & Accessories:
Pipes and fittings is in Upvc
-
-
-
3. MICRON FILTER
Purpose To remove the fine particles up to 05 microns and reduce silt density index levels to acceptable level.
Specifications Cartridge Filter & Housing
Housing:
(a) Make: Kemflo/ Paintair/ Hitech/ Eqlt
(b) MOC of Housing: PP
(c) Length: 20”
(d) Diameter: 2”
(e) Quantity: 1 No
Cartridge
(f) Make: Kemflo, Pentair
(g) Cartridge MOC: Polypropylene
(h) Length: 20”
(j) Diameter: 2”
(k) Quanity: 1 No
(l) Micron rating: 05 micron
-
-
-
4. HIGH PRESSURE PUMP
Purpose To feed the Reverse Osmosis Membrane at pressure more than the osmotic pressure taking into consideration flux rate, flow and recovery.
Specifications
(a) Type: Centrifugal Horizontal type
(b) Flow Rate: 1000 liters per hour
(c) Pressure: 10 Kg/cm2
(d) Cycle: 2900 rpm
(e) Make: CRI
(f) Quantity: 1 No.
-
-
-
5. RO MEMBRANE
Purpose To remove the major part of TDS upto 98% by Reverse Osmosis.
Membranes arranged and designed to give adequate flow and recovery.
Specifications
(a) Type: Spiral Wounded
(b) Diameter of Membrane: 4.0 inch
(c) Length of Membranes: 1Mt.
(d) No of Membranes: 1
(e) Recovery per Membrane : 15-17%
(f) Salt Rejection per Membrane: 98-99%
(g) Make of Membranes: LG
(h) System Recovery: 40-50%
-
-
-
6. RO PRESSURE TUBE
Purpose To pack Reverse Osmosis Membranes and operate at high pressure upto 200-300 psi.
Specifications
(a) MOC: FRP
(b) Diameter of Pressure Vessel: 4 inch
(c) Length of Pressure Vessel: 1.2 m
(d) No Pressure Vessels: 1
(e) No of Membrane per Vessel: 1
(f) Make: Imported
(g) Position: Horizontal
-
-
-
REF & DEEP FREEZER
-
-
-
Supply and fix refrigerators, electric driven (single phase), capacity more than 195 Litres .BEE 5 star rated, stabilizer free operation completion complete all as specified and directed.
2
-
-
Stand by DG Supply
-
-
-
Supply, installation, commisioning and testing of silent type diesel Engine driven generating set of capacity 250 KVA/200KW(0.8 PF), 415 volts, three phase 4 wire system, engine as per IS 10001/10002 and alternator as per IS-13364 complete with relay panel for automatic starting on main failure, control panel having meters, sound proof canopy as per relevant IS and foundation as per manufacturer's recommendations etc including the following
A. ENGINE
Direct injection, water cooled engine, cylinder, in line, 4 stroke, rated at 1500 RPM, not less than 309 BHP, confirming to BS-5514 has the following specifications :-
1
-
-
(i) In line fuel pump with Electronic governor for 250 KVA
(ii) Stainless steel exhaust flexible coupling and exhaust pipe to insulated with glass fire wool to be claded with plain GI sheet & extended out side the building
(iii) Silencer extended out side to the building complete.
(iv) Radiator
(v) Coolant inhabitor
(vi) Plate type lubricant oil cooler
(vii) Spin-on-filters-coolant, fuel & lubricant oil.
(viii) Dry type, heavy duty, replaceable paper element air cleaner with restriction indicator.
(ix) Flywheel housing and flywheel and flywheel to suit single bearing alternator
(x) Electrical starter motor
(xi) Battery charging alternator
(xii) 24/12 Volts, 180 Ah, ESE, battery (as per OEM recommendation) with multistranded copper cable for connecting wire and terminals
(xiii) First fill lub oil.
-
-
-
B. ALTERNATOR
(I) Self excited, self regulated
(ii) Voltage regulation plus/minus 1 percent
(iii) Class 'H' insulation
(iv) Silent pole revolving field
(v) Digital automatic voltage regulator (Part of PCC 1301)
(vi) Noise level - 75db @ 1 meter
(vii) Telephone interference factor - 50
(viii) Total harmonic factor Better than 2%
(ix) Supplying power to variable electrical load for unlimited hours. Prime power (PRP) is in accordance with ISO 8528. Ten percent over load capacity for one hour every 12 hrs of operation and will be suitable tropical conditions
-
-
-
C. FUEL TANK
(a) Fuel tank suitable capacity for minimum 8 hrs run with provision for supply and return lines, level indicator, drain valve, cleaning cover, vent pipe & locking devices shall be provided
(b) Fuel pipe line from fuel tank to FIP of suitable size.
(c ) The fuel tank has to be mounted/located in side the cubicle.
D. ACOUSTIC ENCLOSURE
I) Designed to meet stringent MoEF/CPCB norms 75dBA @ 1 meter.
ii) Air inlet louvers to be designed to operate at rated load even at 50 degree centrigrade air inlet temp.
iii) Cubical to be powder coated for long lasting service life and super finish with UV resistent poder coating, it has to with stand extreme environment. Has to be use stain steel hardware.
iv) Insulation material has to meets exacting IS 8183 speces for better sound (v) Provision of Genset controller for Engine & alternator
-
-
-
E. ACCESSORIES
i) Periodical maintenance tools as per manufacture
ii) Minimum two years spares as manufactures design.
iii) Operational, spare parts & installation guide line catalogue
F. AMF CONTROL PANEL FOR DG SET
(I) MCCB 400 Amps, 4 pole, 415 volts, 25 KA, 50 Hz with thermal magnetic and microprocessor release
(ii) Power contactors of suitable sizes of minimum 400 Amp, Air breake type - 02 Nos
(iii) Digital type multi functional meter -01 Nos (iv) Current transformer (CT) of rating 100/5, tape wound, rated burden 5 VA - 03 Nos
(v) Micro processor based relay of suitable size/ratings-01 Nos
(vi) Smart Battery charger auto/manual switch - 01 Nos
(vii) Suitable annunciation with features of following protections :- Over current, overvoltage, under voltage, under frequency, Low pressure oil.
-
-
-
Note : (a) Provision of PCC plateform as per manufacturer guidelines/specifications of any type and any size, the cost of the same shall be deemed to be included in the unit quoted rates. Nothing shall be admissible on this account
(b) Testing of the DG set shall be carried out by the rep of the accepting office/IEM
(c) The contractor shall submit the drawing for approval of the GE before procurement of the DG set
(d) Resistive load whether water load or strip heaters of suitable capacity and POL/DHPP for testing of DG set to be made available during test by the contractor. The cost of the same shall be deemed to be included in the unit quoted rates.
(e) The DG set shall be procured from authorized OEM and of same group. The accoustic panel shall also be manufactured by the same OEM
(f) Anything missed out above but is required for efficient working of DG set is deemed to be included in the unit quoted rate
-
-
-
Desert Coolers
-
-
-
Supply and installed desert cooler electric driven (single phase) having nominal air flow capacity of 4000 cum per hour, outer body and tank made out of MS sheet of minimum size 2mm thick powder coated, copper wound motor of min 1380 RPM, 230 V, 50 Hz, aluminium fan blade of suitable size according to air flow, water pump of min capacity 20 watt, single phase, 230V, 50 Hz, discharge approx 1600 Ltr/hr at 1.6 mtr head complete all as specified and directed.
58
-
-
INTERNAL ELECTRIFICATION
-
-
-
Supply, install, testing and commissioning and testing factory made and tested design verified as per IS/IEC - 61439-1 & 2, by CPRI approved manufactures LT feeder pillar box (KIOSK) indoor type, platform mounted, including suitable angle iron (4 Nos leg) for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, all as specified and directed, having bus bar chamber with insulated copper bus bars 300 amps rating installed on porcelain insulators. The panel shall be dust and vermin proof, made of 2.00 mm CRCA sheet 75mm x 30 mm thick MS Channel frame 7 tank proceed, duly powder coated finish ,thimbling and cable entry boxes with cable gland incld painting with two coat of synethetic enamel paint over a coat of red oxide primer. Front and back side opening type with aprons for cable entry with double door shutter and locking arrangement, danger plate and earthing terminal and suitable PCC work. The scope of work includes provision of the following :- Incoming :-
(a) MCCB 4 pole 100 Amps, 25 KA, 415V -01 No (b) Bus bar (copper strip)200 Amp 4 Nos (c) Digital panel meter (Amp Voltage meter ) including CTs-01 Nos (d) Digital indication lamp set -01 (e) Slot for electronic energy meter -05 Nos . Outgoing:- (i) MCB SPN 40 Amp 415 V 50 Hz-05 NOs Note:- Contractor shall sumit LT panel drawing for approval of GE before procurement.
1
-
-
S&F Distribution board made out of sheet metal powder coated, factory made, enclousure double door type TPN 4 way vertical type with 200 (Amps rated copper bus bar, neutral bar, earth bar, TP 43 protection including provision of housing of incomer MCCB 63 Amps, triple pole and neutral, 415V, 16 KA breaking capacity fixing of DB flush to wall surface complete all as specified and directed.
3
-
-
Supply and fixing LED light fitting with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver and LED lamp 5700K Rated CCT energy efficient with lumen efficiency corrosponding to five star BEE rating published for year of installation, pf 0.8, colour rendering index not less than 70%, IP20 complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as directed by EIC.
98
-
-
S & F LED Flood light fitting 60 watt, system efficiency not less than 115 lumens/watt, IP 65 protection consisting of high/low voltage cut off maintenance free isolated electronic driver circuits, with 10 KA surge protection, low THD PMMA grade high quality. Transmittance lens, epoxy powder coated Die cast Aluminium housing with weather proof gasket for lamp & driver compartment, Heat resistance toughened glass fitted in cast aluminium housing with SS screws fixed on modified angle for fixing of light fitting as per manufacturer instruction & connecting complete all as specified and directed by Engg –in-charge.
8
-
-
Supply and Fixing cable tray perforated Aluminium pre- Galvanised fixing ,passing through vertical wall ,chiseling ,cutting on vertical/ horizontal wall including make good of disturbed surface complete all as dircected by Engineer in charge.
10
-
-
Sewage Disposal
-
-
-
M/L RCC Septic tank designed to carry sewage and sullae water,excavation in any type o soil,PCC 1:4:8 below oundation,RCC M-30 design Mix in Walls,Base Slab,Baffle walls and Roof Slab including beams etc with Vent shat,manhole openings with cover connection etc complete with effective depth of 1.5 meter and over all depth of 3 meter etc complete all as specified & as shown on drawing for 100 users .
1
-
-
M/L RCC Septic tank designed to carry sewage and sullae water,excavation in any type o soil,PCC 1:4:8 below oundation,RCC M-30 design Mix in Walls,Base Slab,Baffle walls and Roof Slab including beams etc with Vent shat,manhole openings with cover connection etc complete with effective depth of 1.5 meter and over all depth of 3 meter etc complete all as specified & as shown on drawing for 50 users .
1
-
-
Sokage well excavation,in any type of soil , foundation in PCC 1:3:6,wall of honey combed masonary with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM,RCC cover slab in M25/SFRC cover,interconnecting pipes of RCC/DWC complete filled with brick bats o size 1.8 M dia X 4.5 M effective depth.
3
-
-
Flame Proof Lights
-
-
-
Supply and fixing of flame proof exhaust fan of size 230mm sweep with louvers and making suitable size hole and making the surface to match with the existing including electrical connections complete all as specified and directed.
3
-
-
Supply and fixing of Flame proof DB SPN 4 way, double door, 240V with MCB SPN 32 Amp -01 No and MCB SP 6-32 Amp - 02 Nos complete all as specified and directed.
2
-
-
Chemical Earthing
-
-
-
M&L for Chemical Earthing complete with CPRI tested 50mm bore pure copper earth electrode pipe with wall thickness of copper pipe not less than 20 gauge, of length 3000mm, pipe in copper strip Technology with NABL tested, RoHS compliant earth enhancement compound 50 Kg in each bore hole in tripod configuration (three numbers of 50mm dia pure copper electrode pipe) interconnected with 32x6mm size copper strip and connected by means of exothermic brazing & porected by GI pipe light grade 32mm bore and PCC (1:2:4) type B1 earth chamber & cast iron earth pit cover 300x300x3mm connecting to test point & testing on ground complete includingexcavation, earth work, boring in any type of soil strata & cleaning of site complete all as specified and directed.
45
-
-
Note :- (i) Cost of 32x6mm size copper strip and 50mm bore GI pipe light grade required for interconnection of three numbers of pure copper 50mm dia earth electrode is deemed to be included in unit quoted rates. Copper strip of suitable size from earth pit interconnection to test point/equipment shall be measured and paid seperately.
(ii) Cost of earth work, boring, PCC earth pit, RCC cover, testing of earth after completion, connecting and commissioning is deemed to be included in unit quoted rates.
(iii) Marking & painting of earth pit with iron plate of suitable size is deemed to be included in unit quoted rates
(iv) The boring will take place for 350mm dia and 3m depth for three numbers of pure copper earth electrode pipe to form tripod configuration. Earth enhance compound to be filled around the earth electrode in 100mm dia in 3 layers of 1m each by means of PVC pipe of 100mm dia as casing/formwork. The remaining volume of bore shall be filled with clay soil available in vicinity in 3 layers of 1m each. The PVC pipe shall be removed sinultaneously. The cost of all this is deemed to be included in the quoted rate. (v) Minimum distance between each earthing is not less than 3m. (vi) Testing of earthing shall be conducted and result should be less than 1.00 Ohms.
(vii) On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost.
-
-
-
EXTERNAL ELECTRIFICATION
-
-
-
Supply & Installation of 11 KV Outdoor type extensible Ring Main unit (RMU) floor mounted with internal copper bus bars consisting of combinations of 630 Amp 3 Nos. fixed manual Load Break Switch as outgoing & 1 Nos. fixed type manual Vacuum Circuit Breaker as incommer, fixed type manual Vacuum Circuit Breaker All live parts, bus bars, LBSs, VCBs connections of RMU should be enclosed in Stainless Steel tank & sealed for life robotically welded non magnetic and non ferrite 304 grade stainless steel tank of 3 +/-0.5mm thick having IP67 degree of protection filled with gas as insulation with leakage rate less than 0.1% per year tested as per IEC 62271-200. RMU shall have solid earthing system. The earthing busbar shall be provided throughout the length of switchgear & shall be provided in each cable compartment. RMU should complete with all accessories such as Terminal boots, VPIS, cable supports, mechanical indications for Load break switch ON/OFF, VCB ON/OFF, Spring charge, Manometer as per with IEC standards 62271-200, 60056, 60129, 60265, 60298, 60420, 60529 and 60694. Altitude of installation up to 1000m as per IEC 60120. Internal arc type tested for AFLR 20kA for 1 sec with gas release provision from top side. Bushings bolted type mounted outside the tank for connection of external bus bar. The complete enclouser of RMU shall be of IP54. The outer door of enclouser shall cover entire front part of the switchgear including cable compartment in and including the following :-
1
-
-
The configuration of the RMU will 1 VCB as incomer and 2 LBS as outgoing
Each Vacuum Circuit Breaker module should consist of following accessories :-(a) 630A Vacuum circuit breaker module with vacuum circuit breaker, three position isolator/earthing switch, busbars, interlocking, earthbar and stored spring energy mechanism (b) Short time current - 21KA/ 3 sec
(c ) Making Capacity - 50KA
(d) Power frequency withstand voltage - 28KV
(e) Impulse withstand voltage - 75KV
(f) Nominal operating gas pressure - 1.4 Bar abs.
(g) Front cover mechanism - IP2X
(h) Cable covers - 3X with outer enclouser IP54
(j) Stored energy mechanical for manual operation
(k) Cable box for front termination of the cable suitable upto 3 core 300 Sqmm, 11 KV XLPE cable
-
-
-
(l) Right angle boots (push on type)
(m) Arc proof cable covers with self Interlocking mechanism with earth switch (n) Capacitive voltage indication fixed type system as per IEC61243
(o) Mechanical Indications for Load break switch ON, OFF, EARTH
(p) Self Powered Over Current and Earth Fault protection relay (q) Ring core current transformer with suitable ratio 100/5-5, 2.5VA, 10P10 for protection
(r ) Make of Vacuum Interrptor and RMU Manufacturer should be same
(s) 630A Load Break Switch module for making of fault current alongwith Earth Switch of full making capacity
Short time withstand current - 21KA/ 3 sec
Making Capacity - 52.5kAp
Auxiliary contacts - 1NO + 1NC
Power frequency withstand voltage - 38kV
Impulse withstand voltage - 95kV
Nominal operating gas pressure - 1.4 Bar abs.
Front cover mechanism - IP2X
Cable covers - 3X
Snap action mechanism for manual operation and pad-lockable Cable box for front termination of the cable suitable upto 3 core 300 Sqmm, 11 KV XLPE cable
Right angle non-touch proof Termination boots - 1 Set (R,Y,B)
Make : ABB, Siemens, Schneider. Note - RMU shall be placed on PCC plateform of size and design recommended by manufacturer and the cost of the same shall be deemed to be included in unit quoted rates.
-
-
-
Supply and Installation of11 KV, 630 Amp Load break switch with 200 Amp DO set and earth switch complete all as specified and directed.
1
-
-
S&F of PVC insulated flat three core cable with aluminium conductor 1.5 Sqmm for connecting street light fitting from junction box complete all as specified and directed.
600
-
-
M&L for street light pipe bracket made out of GI pipe 40mm dia bend to shape 0.9 vertical and 0.6 M to angle of 120 degree complete all as specified and directed.
86
-
-
Supply and fixing of street light junction box of size not less than 200x140x95mm which is totally safe, shock proof, impact resistant, weather proof, dust proof, rust proof, halogen and silica free, having internal embedded gasket technology made of PUR with suitable degree of protection and cable glands complete all as specified and directed.
86
-
-
Disconnecting, Dismantling, taking down of existing APFC panel of any type and size and Supply, installation, commissioning and testing of outdoor type, 440volts, AC, LT, APFC panel of 150 KVAr capacity, factory fabricated, made out of 3.15mm CRCA sheet, CPRI approved, duly wiring with copper flexible wire of suitable rating for power control , Panel shall be dully powder coated with 8 tanks sheet treatment ( De-greasing, water rinsing, de-rusting, water rinsing, Activation- phosphating, water rinsing, (Passivationthickness of powder coating shall no be less than 80 microns) in and including the following :- (A) Incoming
(i) MCCB, 415 volts, 4 pole, 400 Amps, 36 kA with rotary Handle Mechanism - 01 Nos
(ii) Digital Ammeter with built - in - selector switch Aux Supply 230 Volts, AC - 01 Nos
(iii) Digital Voltmeter with built in selector switch Aux Supply 230 Volts, AC-01 Nos
1
-
-
(iv) LED indication lamp 230 Volts, AC 22.5mm dia RYB-03 Nos
(v) MCB 2 Amp, Single Pole-03 Nos
(vi) Microprocessor APFC relay with single CT sensing 12 stages auxilary supply 230volts, AC - 01 Nos
(vii) Aluminium busbar 25x10mm, TPN - 01 Set
(viii) Auto/Manual Switch - 01 Nos
(B) Outgoing
(i) Capacitor 20 KVAr ultra heavy duty 440V cylindrical - 02 Nos
(ii) Capacitor 15 KVAr ultra heavy duty 440V cylindrical - 02 Nos
(iii) Capacitor 10 KVAr ultra heavy duty 440V cylindrical - 06 Nos
(iv) Capacitor 05 KVAr ultra heavy duty 440V cylindrical - 04 Nos
(v) MCB Triple pole 63 Amps, 10 kA, 'C' sries - 02 Nos
(vi) MCB Triple pole 40 Amps, 10 kA, 'C' sries - 02 Nos
(vii) MCB Triple pole 32 Amps, 10 kA, 'C' sries - 02 Nos
(viii) MCB Triple pole 16 Amps, 10 kA, 'C' sries - 10 Nos
-
-
-
(ix) Capacitor duty contactor 3 pole 20 KVAr - 02 Nos
(x) Capacitor duty contactor 3 pole 15 KVAr - 02 Nos
(xi) Capacitor duty contactor 3 pole 10 KVAr - 06 Nos
(xii) Capacitor duty contactor 3 pole 05 KVAr - 04 Nos
(xiii) 22.5mm dia Push Button ON/OFF-10 set
(xiv) 22.5 mm dia LED Red - 10Nos
(xv) 22.5mm dia LED Green-10 Nos
(xvi) Armoured 2 core copper cable 1.5sqmm shall be provided for sensing CT(
xvii) Sensing CT as per site load condition shall be provided alongwith APFC Panel
(xviii ) All power connection shall be done with 1100 volts FRLS copper flexible wire with copper termination of proper size and proper type
Note (i) GA drawing for APFC panel shall be got approved from the Accepting Officer/Engineer-in-charge before manufacturing of APFC panels
(ii) PCC plateform of suitable size shall be provided after demolition of existing PCC plateform, The cost of all above shall be demmed to be included in unit quoted rates.
-
-
-
Supply, installation, testing & commissioning of Feeder Pillar Box outdoor type, suitable for operation on 415 volts, AC 3 phase, 4 wire, 50 Hz electric supply system, factory made out of 50 x 50 x 6 mm angle iron frame and 2 mm thick CRCA sheet side covers with front and back hinged doors with proper locking arrangement, rubber gasket on front and back to make it dust and vermin proof, powder coated including 500 Amp rated aluminium busbar sleeved with heat shrink sleeve colour coated for 3 Phase, 4 wire electric supply system and wiring with suitable size of copper cable complete with the following accessories all as specified and directed by the Engr-in-charge. (Note: Feeder pillar box shall be mounted on PCC 1:2:4 type B-1 (with 20 mm graded stone aggregate) foundation block of suitable size upto 40 cm above ground level as directed. The cost of the PCC block shall be deemed to be included in the unit rate quoted for the item & depth of the panel not less than 75 cm):
Incoming : MCCB 630 Amp 415 Volts, 35 KA, 4 pole, 50 Hz, with thermal magnetic release
1
-
-
Outgoing :
(a) MCCB 100 Amp 415 Volts, 16 KA, 4 pole, 50 Hz, with adjustable thermal & adjustable magnetic setting - 03 No
(b) MCCB 63 Amp 415 Volts, 16 KA, 4 pole, 50 Hz, with adjustable thermal & fixed magnetic setting - 03 Nos (c) MCB TPN 40 Amp 415 Volts, 10 KA, C curve, - 03 Nos
(d) Digital Amp meter 0-500 Amp with selector switch
(e) Digital Volt meter 0-500 Volts with selector switch
(f) Phase indicator lamp - 01 set (Set of three)
(g) Time switch astro type (having longitude and latitude of Indian cities in memory) 415 Volt three phase of 20 Amp rating with contactor fitted inside steel enclosure - 02 No.
-
-
-
Supply, installation, testing & commissioning of Feeder Pillar Box outdoor type, suitable for operation on 415 volts, AC 3 phase, 4 wire, 50 Hz electric supply system, factory made out of 50 x 50 x 6 mm angle iron frame and 2 mm thick CRCA sheet side covers with front and back hinged doors with proper locking arrangement, rubber gasket on front and back to make it dust and vermin proof, powder coated including 500 Amp rated aluminium busbar sleeved with heat shrink sleeve colour coated for 3 Phase, 4 wire electric supply system and wiring with suitable size of copper cable complete with the following accessories all as specified and directed by the Engr-in-charge. (Note: Feeder pillar box shall be mounted on PCC 1:2:4 type B-1 (with 20 mm graded stone aggregate) foundation block of suitable size upto 40 cm above ground level as directed. The cost of the PCC block shall be deemed to be included in the unit rate quoted for the item & depth of the panel not less than 75 cm):
Incoming:-
MCCB 400 Amp 415 Volts, 35 KA, 4 pole, 50 Hz, with thermal magnetic release
1
-
-
Outgoing :
(a) MCCB 320 Amp 415 Volts, 25 KA, 4 pole, 50 Hz, with adjustable thermal & adjustable magnetic setting - 03 No
(b) MCCB 63 Amp 415 Volts, 16 KA, 4 pole, 50 Hz, with adjustable thermal & fixed magnetic setting - 02 Nos (c) MCB TPN 40 Amp 415 Volts, 10 KA, C curve, - 04 Nos
(d) Digital Amp meter 0-500 Amp with selector switch
(e) Digital Volt meter 0-500 Volts with selector switch
(f) Phase indicator lamp - 01 set (Set of three)
(g) Time switch astro type (having longitude and latitude of Indian cities in memory) 415 Volt three phase of 20 Amp rating with contactor fitted inside steel enclosure - 02 No.
-
-
-
Supply, installation, testing & commissioning of Feeder Pillar Box outdoor type, suitable for operation on 415 volts, AC 3 phase, 4 wire, 50 Hz electric supply system, factory made out of 50 x 50 x 6 mm angle iron frame and 2 mm thick CRCA sheet side covers with front and back hinged doors with proper locking arrangement, rubber gasket on front and back to make it dust and vermin proof, powder coated including 200 Amp rated aluminium busbar sleeved with heat shrink sleeve colour coated for 3 Phase, 4 wire electric supply system and wiring with suitable size of copper cable complete with the following accessories all as specified and directed by the Engr-in-charge. (Note: Feeder pillar box shall be mounted on PCC 1:2:4 type B-1 (with 20 mm graded stone aggregate) foundation block of suitable size upto 40 cm above ground level as directed. The cost of the PCC block shall be deemed to be included in the unit rate quoted for the item & depth of the panel not less than 75 cm):
Incoming:
MCCB 100 Amp 415 Volts, 25 KA, 4 pole, 50 Hz, with thermal magnetic release
1
-
-
Outgoing :
(a) MCCB 63 Amp 415 Volts, 16 KA, 4 pole, 50 Hz, with adjustable thermal & adjustable magnetic setting - 03 No
(b) MCB TPN 40 Amp 415 Volts, 10 KA, C curve, - 01 Nos
(c) Digital Amp meter 0-200 Amp with selector switch
(d) Digital Volt meter 0-500 Volts with selector switch
(e) Phase indicator lamp - 01 set (Set of three)
-
-
-
Supply, installation, testing & commissioning of Feeder Pillar Box outdoor type, suitable for operation on 415 volts, AC 3 phase, 4 wire, 50 Hz electric supply system, factory made out of 50 x 50 x 6 mm angle iron frame and 2 mm thick CRCA sheet side covers with front and back hinged doors with proper locking arrangement, rubber gasket on front and back to make it dust and vermin proof, powder coated including 500 Amp rated aluminium busbar sleeved with heat shrink sleeve colour coated for 3 Phase, 4 wire electric supply system and wiring with suitable size of copper cable complete with the following accessories all as specified and directed by the Engr-in-charge. (Note: Feeder pillar box shall be mounted on PCC 1:2:4 type B-1 (with 20 mm graded stone aggregate) foundation block of suitable size upto 40 cm above ground level as directed. The cost of the PCC block shall be deemed to be included in the unit rate quoted for the item & depth of the panel not less than 75 cm):
Incoming:
MCCB 350 Amp 415 Volts, 35 KA, 4 pole, 50 Hz, with adjustable thermal & adjustable magnetic setting.
1
-
-
Outgoing :
(a) MCCB 320 Amp 415 Volts, 25 KA, 4 pole, 50 Hz, with adjustable thermal & adjustable magnetic setting - 1 No
(b) MCCB 63 Amp 415 Volts, 16 KA, 4 pole, 50 Hz, with adjustable thermal & fixed magnetic setting - 01 Nos (c) MCB TPN 6-40 Amp 415 Volts, 10 KA, C curve, - 06 Nos
(d) Digital Amp meter 0-500 Amp with selector switch
(e) Digital Volt meter 0-500 Volts with selector switch
(f) Phase indicator lamp - 01 set (Set of three)
(g) Time switch astro type (having longitude and latitude of Indian cities in memory) 250 Volt three phase of 20 Amp rating with contactor fitted inside steel enclosure - 02 No.
-
-
-
M&L for sand filling 8cm before laying of cable and 15cm after laying of cable and punned down by hand ramming to 18cm complete all as specified and directed.
41
-
-
External Water supply
-
-
-
M&L for cutting of existing DI pipe of size 100mm dia and making arrangement for insertion of new NRV alongwith following accessories : Tail piece with flanged end-02 Nos, Tail piece plain - 01 No, Double collar tyton joints-02 Nos, Gaskets, Nut bolts, Rubber rings etc. all as directed including necessary excavation & earth work as required of 100mm dia of sizes.
1
-
-
Supply and lay pipe ductile Iron , S/S including specials, Class “K-7” ,100 mm (4”) dia.
100
-
-
Supply and fixing of Submersible pump, electric driven 415 V, TP suitable for 200/250 mm dia bore well (Casing pipe size 200/250 mm) supply and Install complete upto 5 HP inclusive of 40 metre long submersible cable and starter. (2 x 5HP)
2
-
-
Supply and fixing of Submersible pump starter of capacity up to 5 HP with lock on rotor, single phase preventor, overload relay, suitable capacity contactor and any other accessories required for smoothe functioning of the starter complete all as specified and directed.
2
-
-
M & L for construction of stone masonry valve pit of size 900x 900 x 900 mm (internal dimension) with MS top cover of 3 mm thick sheet, fixed on frame made out of angle iron 40 x 40 x 6 mm thick, with locking arrangements including two coats of synthetic enamel paint over a coat of red oxide primer to MS sheet internally and externally & iron surface, stone masonry work in cement mortar 1:4, 15 mm thick plastering in cement mortar 1:4 (internally & externally) 150 thick plain cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate for base, 100mm thick PCC 1:2:4 type B-1 using 20 mm graded mechanically crushed stone aggregate for coping two coats of white wash internally after prepartion the surface complete all as specified & as directed.
10
-
-
M & L for construction of stone masonry valve pit of size 1200x 1200 x 1200 mm (internal dimension) with MS top cover of 3 mm thick sheet, fixed on frame made out of angle iron 40 x 40 x 6 mm thick, with locking arrangements including two coats of synthetic enamel paint over a coat of red oxide primer to MS sheet internally and externally & iron surface, stone masonry work in cement mortar 1:4, 15 mm thick plastering in cement mortar 1:4 (internally & externally) 150 thick plain cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate for base, 100mm thick PCC 1:2:4 type B-1 using 20 mm graded mechanically crushed stone aggregate for coping two coats of white wash internally after prepartion the surface complete all as specified & as directed.
6
-
-
Sch of credit Rs 2,56,172.50
-
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements