Military Engineer Services Tender
If you're looking for Rajasthan tenders online and are tired of typing tender ID over and again or going through the cumbersome government websites for it, you are in luck. We have collated every Eproc Rajasthan tender on BidAssist. And for any queries related to an e-tender Rajasthan, like bidding process, registration process, etc., are explained below. Read on.
Military Engineer Services - MES Tender
Civil And Construction
Building Construction
Eprocure
Opening Date18 Jul 2023
Closing Date16 Aug 2023
Tender Amount₹ 25,00,000
Costs
EMD
₹ 50,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2023_MES_609538_1Bid Award Id
ViewTender No
8934-27/GE/2023-24Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
M & L rendering 5 mm thick in cement mortar (1:3) on fair faces of concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified & directed by Engr-in-charge.
190
-
-
M&L preparing newly plastered surface of wall and applying 2 coats of acrylic distemper on walls over a coat of primer complete all as specified & directed
180
-
-
M&L for preparation of new plastered surface of walls and applying two coats of cement base paint complete all as specified & directed
280
-
-
M&L preparing newly plastered surface of ceiling and applying three coats of white wash on ceiling complete all as specified & directed
190
-
-
Demolition of brickwork or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles including cleaning and stacking serviceable brick for re use and balance removing rubbish from the site complete all as specified and as directed by Engineer-in-charge.
5
-
-
M&L for brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed by Engineer-in-charge.
5
-
-
Taking up or down steel tubing 15mm bore including all fittings and connections, cleaning for refixing or removal to store complete all as specified and directed
35
-
-
,---ditto--- all as per serail item No. 10 above but for 20mm dia pipe complete all as specified and directed
18
-
-
,---ditto--- all as per serail item No. 10 above but for 25mm dia pipe complete all as specified and directed
15
-
-
S&F 15 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling/ laid in floor complete all as specified and directed.
35
-
-
,---ditto--- all as per serail item No. 13 above but for 20mm dia pipe complete all as specified and directed
18
-
-
,---ditto--- all as per serail item No. 13 above but for 25mm dia pipe complete all as specified and directed
15
-
-
S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20mm bore complete all as specified and directed
8
-
-
S&F in repair vitreous china wash hand basin coloured Flat back of size 550x400mm, including 32mm dia chromium plated waste coupling long screwed shank and fly nut, flanged end bedded in red led cement and other end fixed and PVC waste pipe including cutting for and pinning in ends of brackets in CM 1:3 all as specified .
10
-
-
S&F in repairs PVC valve less, syphonic action type flushing cistern,10 ltrs capacity low level, white, with inlet ball valve, float, handle flush pipe 32mm dia, for low level cistern of polyethylene of low or high density or PVC, and connection to pipes complete all as specified and directed by Engineer-in-Charge.
15
-
-
S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with integral foot rests including concrete fixed complete all as specified and directed by Engineer-in-Charge.
8
-
-
S&F in repair pillar tap, fancy type, cast copper alloy chromium plated with capston head, screwed down high pressure with or without lettered with long screwed shank and fly nuts, screwed for iron pipe of 15 mm bore complete all as specified and directed. Note: Wt not less than 450 gms
12
-
-
S&F in repair bib tap 15mm bore cast copper alloy chromium plated long body fancy type with capston head and cup screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge.
25
-
-
S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.
40
-
-
S&F in repair tubular towel rail, Brass chromium plated 20 mm dia, 'D' type, 60cm long between flanges complete all as specified and as directed by Engineer-in-Charge.
8
-
-
S&F in repair CP brass stop/angle valve fancy type 15 mm bore cast copper alloy screwed down high pressure fancy type with long shank and cup fixed all as specified.
35
-
-
S&F in repair, shower rose, 125 mm size, brass chromium plated with swivel joint complete all as specified and directed.
8
-
-
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises complete all as specified and directed.
803
-
-
M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floor over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match the floor all as specified and directed.
320
-
-
M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tile exc 0.11 Sqm but not exc 0.18 Sqm in floor over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match the floor all as specified and directed.
45
-
-
M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm as in dado/skirting over and including 10 mm thick rendering on vertical surface in cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match all as specified and directed.
5
-
-
M&L for glazed ceramic coloured tiles of size 450 x 300 x 7 mm thick on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match the floor all as specified and directed.
380
-
-
M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 20 mm thick screed bed in CM 1:6 complete all as specified and directed.
12
-
-
Rounding off edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations all as specified and directed
52
-
-
M&L for machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid over cement screed base laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed with grey cement slurry mixed with pigment to match shade of the slab including rubbing and plishing complete all as directed.
40
-
-
M&L for machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over and including 10 mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry mixed with pigment to match shade of the slab including rubbing and plishing complete all as directed.
1
-
-
Dismantling of water tanks of capacity exc 500 and n.exc 1000 ltrs and removing from site all as specified and directed.
5
-
-
S&F for Rotational moulded polythene water storage tank 500 ltr capacity vertical with closed top, ISI marked hoisted and fixed in position all as specified in SSR part-I. including 20 mm bore PTMT float valve, connection nipple 2 Nos complete all as specified and directed..
5
-
-
S & F in repairs ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed for 20mm dia pipe complete all as specified and directed.
Note: Minimum weight 20 mm - 210 gms
18
-
-
Complete removal of existing treatment mechanically using electric grinder and applying two coats oil bound distemper over a coats of primer over 3 mm thick wall care putty and including preparation of surface complete all as specified and directed by Engr-in-Charge.
105
-
-
Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or
insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.
200
-
-
S&F armstrong mineral fiber accoustical suspended ceiling system with ANF(Micro look) EGE tiles with arm strong silhouette exposed grid. The tiles should have humidity resistance (RH) of 90%. NRC 0.5%. Light reflectance shall be more than 85% thermal conductivity K=0.052-0.057 w/mk. colour shall be white, fire perfomance class 0/class 1 (BS 4760 in module size of 600mmx600mmx15mm with bioblock coating on the face of tiles. suitable for green building application with recycle content of 63% the tiles shall be laid on arm strong silhouette profile grid system with 15mm with flanges incorporating 6mm central revel in white/black colour and with a web height of 45mm and and load carrying capacity of minimum 15.68kg/sqm.silhouette , main runner and cross runner shall have mitred end and birdsmouth notches to provides mitred juction.Tee section shall have a galvanising of 125gms/sqm complete all as specified and directed by Engineer-in-charge.
200
-
-
Dismantling wrought iron or mild steel work of any description not otherwise specially provided complete all as specified and directed.
2.8
-
-
M&L for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates and conforming to Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed
280
-
-
Dismantling asbestos cement (corrugated / semi corrugated) sheets including ridges as in roof covering all as specified & directed by Engineer-in-Charge.
410
-
-
S & F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.
400
-
-
S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified
10
-
-
Taking down Wall panelling and similar work, any description, fixed in any position complete all as specified and directed.
120
-
-
S & F Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet used inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.
120
-
-
S&F in repairs stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.
60
-
-
S&F in repairs stainless steel curtain rods, standrad quality, not less than 28mm dia with heads , etc. complete all as specified and directed by Engr-in-Charge.
250
-
-
S&F in repair kitchen sinks made of stainless steel 1mm thick with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to waste pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-in-Charge.
2
-
-
Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks etc., complete all as specified and directed
Note : Measured overalll as fixed along the cente line over fittings and accessories.
80
-
-
S&F 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as specified and directed
80
-
-
Taking down chowkhats or frames n.exc 1.5 sq. m each with shutters (without taking off shutters from the frame) complete all specified and directed.
18
-
-
Taking down chowkhats or frames exc 1.5 sq. m but n.exc 4.0 sq. m each with shutters (without taking off shutters from the frame) complete all specified and directed directed.
25
-
-
Taking down existing shutter and refixing in same opening shutters of any description exc 1.0 Sqm but not exc 2.0 Sqm each all as specified and directed.
(Note:- 'Refixing' includes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc.)
18
-
-
Supply and fixing of Fibre glass Reinforced plastic (FRP) door frame of required colour of cross-section 90mm x 45mm having single ribate of 32mm x 15mm to recieve shutter of 30mm thick including laminated door frame moulded with fire retardant grade unsaturated polyster resin and chopped strand mat(CSM) also door frame laminated shall be 2mm thick and shall be filled with suitable wooden block of 2nd class hard wood, frame shall be covered with fibre glass from all sides. MS stay flat iron 25mm x 3mm shall be provided at the bottom to steady the frame complete all as specified and as directed by Engineer-in- charge.
70
-
-
Supply and fixing of 30 mm thick glass fibre reinforced plastic (FRP) paneled door shutter conferming to IS:14856-2000 of required colour and made with fire retardant grade unsaturated polyster resin,moulded to 3mm thick FRP laminated for forming hollow rails and style with suitable second class hardwood timber block inside at required places for fixing of fittings,cast molithically with 5mm thick FRP laminated for panels including fixing to frames,complete all as specified and as directed by Engineer-in- charge.
15
-
-
M & L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, conforming to Fe 410 -W (Gde- E- 250) quality-A complete all as specified and directed.
200
-
-
S & F hold fast of flat iron 25 x 3 mm confirming to Fe-290 or Fe-330 including perparing the surfaces & treated with two coats fo coaltar & sanded with clean sharp sand complete all as specified and directed
20
-
-
S&F for 35 mm thick 2nd class hard wood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.
16
-
-
S&F for 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed.
14
-
-
S&F for powder coated aluminium frame for doors, windows, ventilators and aluminium partition with one or more rebates including jointing cleats glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete with locking arrangements for fixing with powder coating on aluminium sections, minimum thickness of poweder coating shall be 50 micron as per the specification. The top and bottom horizontal members and vertical members adjacent to wall shall be fixed with floor, ceiling, walls and cills where required and fixed with the help of rawl plugs and screws or with fixing clips or with expansion hold plate fastners. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically whereever required complete in all respect all as specified & directed by Engr-in-Charge. Make of Al Section : Jindal / Hindalco / NALCO
250
-
-
S&F for powder coated anodised aluminium door shutters,, aluminium sections weighing exc 0.55 Kg/m including necessary necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges (03 Nos), anodised aluminium snap beading, screws, complete all as specified Make of Al Section : Jindal / Hindalco / NALCO
14
-
-
S&F for powder coated anodised aluminium window and ventilator shutters, side hung type without sash, aluminium sections weighing exc 0.55 Kg/m (1.50 to1.80mm th) including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (01 No) hinges type B-21 100 mm long (2 Nos) suitalbe handle (01 No) in each window shutter and necessay accessary as required complete all as specified and directed by Engineer-in-charge (Note: Glass will measured and paid separately). Make of Al Section : Jindal / Hindalco / NALCO
12
-
-
M &L for factory made Steel windows conforming to IS-1038 with side hung shutters including box type hinges with 02 Nos MS 100 mm size barrel tower bolt for each leaf and Z section steel handle and and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.
39
-
-
S & F 3 mm thick pin headed/figured/frosted glass ordinary quality and glazing with oil putty/wooden beading in square n.exc. 0.5 sqm in each pane incl hacking out old brocken glass of any description complete all as specified and directed by Engr-in-charge.
30
-
-
S & F in repairs double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.
5
-
-
S & F 3 mm thick sheet glass, ordinary quality and glazing with aluminium snap beading of any size of glass in each pane with solar control film 25 micron reflective type sticked to glass panes as per instruction of manufaturers all as specified and directed.
18
-
-
S & F mortice lock, vertical type, size 100 mm brass 4 levers all as specified and directed.
6
-
-
S&F for 100 mm long butt hinges, extruded aluminium alloy with galvanised mild steel hings pin, anosied and fixed complete all specified and directed.
32
-
-
S&F for 200 mm long aluminium anodised barrel tower bolt, of extruded sections complete all as specified and directed.
48
-
-
S&F for 125 mm long aluminium anodised handle, cast type complete all as specified and directed.
22
-
-
S&F for 150 mm long extruded aluminium alloy handle, fabricated type anodised complete all as specified and directed.
24
-
-
S&F for 100 mm long butt hinge, medium weight, cold rolled mild steel all as specified and directed.
32
-
-
S&F for 300 mm long mild steel sliding door bolt type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.
9
-
-
S&F for 300mm ordinary rat tail rod pattern springs including roller and roller plate complete mild steel fixed complete all as specified and directed.
8
-
-
S&F for stainless steel wire cloth 0.63 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples all as directed.
50
-
-
Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or metal surface, drilling out old gazing clips and providing and fixing new ones complete all as specified and directed.
49
-
-
S&F for 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring all as directed.
8
-
-
M&L for preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer all as specified.
40
-
-
M & L for painting steel and iron surfaces of any discription,over 10 cm width or girth, with preparation of new or previously untreated surfaces priming with one coat of read oxide & finish with two coats of synthetic enamel paint ordinary tint all as spefified and directed by Engr-in-Charge.
42
-
-
S&F in repair 300 mm long mild steel sliding door bolt type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.
12
-
-
S&F in repair 300mm long aluminium alloy, anodised, sliding door bolt type not less than 16mm dia fixed all as specified & directed by Engr-in- charge.
12
-
-
S&F in repair 300mm ordinary rat tail rod pattern springs including roller and roller plate complete mild steel fixed complete all as specified and directed.
13
-
-
S&F in repair 200 mm long aluminium anodised barrel tower bolt, of extruded sections complete all specified and directed.
20
-
-
S&F in repair 150 mm long extruded aluminium alloy handle, fabricated type anodised complete all specified and directed.
18
-
-
Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ
-
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements