Military Engineer Services Tender
If you're looking for Rajasthan tenders online and are tired of typing tender ID over and again or going through the cumbersome government websites for it, you are in luck. We have collated every Eproc Rajasthan tender on BidAssist. And for any queries related to an e-tender Rajasthan, like bidding process, registration process, etc., are explained below. Read on.
Military Engineer Services - MES Tender
Telecommunication Services
Eprocure
Opening Date23 Nov 2024
Closing Date14 Dec 2024
Tender Amount₹ 25,00,000
Costs
EMD
₹ 50,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_685288_1Tender No
GE SGNR/TOK-70 OF 2024-25Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
M&L for prepration of old painted wooden surfaces of any description not otherwise described over 10.0 cm width or girth and applying one coat of synthetic enamel paint @0.56Litre/10 Sqm/Coat complete all as specified and as directed.
1200
-
-
M&L for preparation of old painted steel surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint @0.60Litre/10Sqm/Coat complete all as specified and as directed.
1500
-
-
Taking down cement plaster of any description on brick or stone walls/ceiling including raking out joints,hacking for key,scrubbing down with water etc complete all as specified and as directed.
808
-
-
Demolition of brickwork or stone/ boulder masonry, but built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.
3
-
-
M&L for brick work with fly ash bricks, straight or curved on plan, exc 6m mean radius built in CM 1:4 complete all as specified and as directed.
3
-
-
M&L for 15mm thick plastering in cement mortar on brick/concrete wall surfaces externally in CM (1:4) with water proofing compound or any other equivalent brand as approved by GE @ 2% by weight of cement and finishing the surfaces fair and even without using extra cement complete all as specified & directed. (Note : The WPC shall be measured and paid seperately under respective items).
458
-
-
M&L in repairs 10mm thick any type of faces of brick or concrete surfaces in cement mortar 1:3 work in isolated width or in widths not forming a part of general plastering work exc 15 cm but n. exc 30 cm in width finished even and smooth without using extra cement complete all as specified and as directed.
120
-
-
M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement internally complete all as specified and as directed.
188
-
-
M&L for rendering 5mm thick on fair faces of concrete surfaces as in ceiling in cement morter 1:3 internally up to all floor complete all as specified and as directed.
130
-
-
S&F chicken wire mesh of mesh size 12 mm and wire diameter 0.63mm for lathing including all laps, cuttings & waste fixing in old RCC slab/beam/chajja complete all as specified and directed.
15
-
-
Supply only Integral water proofing compound as per specifications and ISI approved complete all as specified and as directed.
15
-
-
M&L for preparation of newly plasterd surfaces of ceiling and applying three coats of white wash by making the lime slakedat site and shall be mixed and stirred about 05 litre of water for 01 Kg of unslaked lime to make thin cream. Then allowed to stand and then be screened through thin coarse cloth.1 Kg of gum dissolved in hot water to be added with every 01 cubic meter of cream. About 1.30 Kg of Sodium Chloride to be added for every 10 Kg of lime and small quantity of ultramarine blue (upto 3gm/Kg of lime) shall also be added to the last two coats of white wash including filling of wall care putty in dipressions/indulations/uneveness complete all as specified and as directed.
130
-
-
M&L for two coats of acrylic emulsion distemper @ 10Sqm/Litre/2 Coat applied by roller over a coat of primer @10Sqm/Ltr/Coat and acrylic wall care putty (thickness vary from 1.5mm to 2.5mm as required for desired smoothness and levelling of surfaces in two or more layers) including preparation of newly plastered surfaces of wall by using following brands complete all as specified and as directed.
Notes : - (i) The prepared surface after wall putty, the contractor will inform to the GE as well as Engineer in Charge for site inspection before applying further finishes.
(ii) Written approval of prepared surfaces from the GE and Engineer in Charge shall be obtained in writing before application of finishes.
188
-
-
M & L for preparation of newly plastered surfaces and finishing walls with Acrylic Smooth exterior emulsion paint of required shade new work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior weather coat primer applied @ 2.20 kg/10 sqm) and wall care putty for external surfaces of walls (thickness vary from 1.5mm to 2.5mm as required for desired smoothness and levelling of surfaces in two or more layers) by using roller complete all as specified and directed.
Notes : - (i) The prepared surface after wall putty, the contractor will inform to the GE as well as Engineer in Charge for site inspection before applying further finishes.
(ii) Written approval of prepared surfaces from the GE and Engineer in Charge shall be obtained in writing before application of finishes.
458
-
-
M & L for complete removal of existing treatment of wall surfaces and applying two coat Acrylic Smooth exterior emulsion paint of required shade applied @ 1.0 ltr/10 sqm/coat over and including priming coat of exterior weather coat primer applied @ 2.20 kg/10 sqm) applied @ 2.20 kg/10 sqm) and wall care putty for external surfaces of walls (thickness vary from 1.5mm to 2.5mm as required for desired smoothness and levelling of surfaces in two or more layers) by using roller complete all as specified and directed.
Notes : - (i) The prepared surface after wall putty, the contractor will inform to the GE as well as Engineer in Charge for site inspection before applying further finishes.
(ii) Written approval of prepared surfaces from the GE and Engineer in Charge shall be obtained in writing before application of finishes.
12000
-
-
M&L for complete removal of existing treatment and finishing of walls surfaces of any description over 10cm girth and aplied two coat of plastic emulsion paint @1.6 Ltr/10 sqm/1Coat over a coat of primer @ 10Sqm/Litre/Coat and average 2mm thick (in 2 or more coats as desired smoothness and levelling of surfaces) wall care putty complete all as specified and as directed.
Notes : - (i) The prepared surface after wall putty, the contractor will inform to the GE as well as Engineer in Charge for site inspection before applying further finishes.
(ii) Written approval of prepared surfaces from the GE and Engineer in Charge shall be obtained in writing before application of finishes.
400
-
-
M&L for apply one coat of acrylic emulsion distemper @ 20Sqm/Litre/ Coat applied by roller including filling acrylic wall care putty in depressions, holes & undulations on surfaces of wall by using following brands complete all as specified and as directed.
Notes : - (i) The prepared surface after wall putty, the contractor will inform to the GE as well as Engineer in Charge for site inspection before applying further finishes.
(ii) Written approval of prepared surfaces from the GE and Engineer in Charge shall be obtained in writing before application of finishes.
7780
-
-
M&L for preparation of old plasered or unplastered wall surfaces washing or rubbing down and applying one coats of cement base paint @1.07Kg/10 Sqm/coat complete all as specified and as directed.
3500
-
-
M&L for prepation of washing, rubbing down, scraping using steel wire mesh etc and applying 2 coat of white wash on old decorated ceiling surfaces complete all as specified and as directed.
2400
-
-
M&L for finishing of concrete or old walls plastered surfaces over 10cm girth with two coat of synthetic enamel paint (0.85Ltr/10 sqm for each coat) over a priming coat complete all as specified and as directed.
400
-
-
M&L for TMT bars 8 to 10 mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia using TMT bars complete all as specified and directed.
100
-
-
M&L for removing cover and loose concrete from main reinforcement using wooden mallets/wire brush/waterjet to complete expose the reinforcement in the distressed portion of column, beam, bracings and chajja etc (All loose unsound and cracked concrete should be removed and plan area of concrete surface to be measured) at any height complete all as specified and directed.
20
-
-
M&L for removing the rust from main reinforcement completely using sand paper or wire brush and remove non metal complex compound formed due to corrosion of rust at any height and then applying rust removing chemical complete all as specified and directed.
40
-
-
M&L for applying epoxy based bond coat using brush and applying polymer concrete (not less than 20 mm thick) in the proportion of (1:3:1) one part of cement 3 part of sand and 1 part of 10 mm and down stone aggregate using 8-10 kg of acrylic based polymer per 50 kg bag of cement all as manufacturer's instruction complete all as specified and directed.
(Note: For item No 20 to 25 : The rates should include necessary formwork, scaffolding for repair to work @ height exc 3.00 mtr of the building )
25
-
-
Desmantling of concrete of any description in any position not otherwise specifically provided for complete all as specified and directed.
0.8
-
-
M&L for providing precast cement concrete louvres and jallies, 35mm thick (measured solid) cm 1:4 type-B0 1:2:4 (12.5mm) including all mouldings but excluding frame (Pre cast frame shall be measured separately and paid complete all as specified and directed.
26
-
-
Providing precast cement concrete in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone wallin) corbels, brackets, etc (of any section indicated), with plain fair faces, incl chamfers, weatherings, throating etc. and setting in mortar CM type B1 1:2:4 (20 mm agrregate) complete with joints to match complete all as specified and directed.
0.3
-
-
Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick sorrounds, glazed with oil putty or fixed with beads complete all as specified and directed.
20
-
-
S&F sheet glass 4.0 mm thick ordinary quality and glazing with oil putty or glazing pins / spring clip in square, rectangle not exc 0.5 Sqm in each pan complete all as specified and directed.
20
-
-
M&L complete removal of existing treatment and finishing walls with textured exterior/interior paint of required shade (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of primer applied @ 2.20kg/10 sqm with average 2mm thick (in 2 or more coats as desired smoothness and levelling of surfaces) wall care putty complete all as specified and directed.
Notes : - (i) The prepared surface after wall putty, the contractor will inform to the GE as well as Engineer in Charge for site inspection before applying further finishes.
(ii) Written approval of prepared surfaces from the GE and Engineer in Charge shall be obtained in writing before application of finishes.
200
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%