Military Engineer Services Tender
If you're looking for Rajasthan tenders online and are tired of typing tender ID over and again or going through the cumbersome government websites for it, you are in luck. We have collated every Eproc Rajasthan tender on BidAssist. And for any queries related to an e-tender Rajasthan, like bidding process, registration process, etc., are explained below. Read on.
Costs
EMD
₹ 15,00,000Document Cost
₹ 3,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_679054_1Tender No
80887Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Lump sum price worked out by the contractor for "ROAD, PATH AND CULVERT" as listed in Schedule ‘A’ Part-IV representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES
1
24209483
-
Lump sum price worked out by the contractor for "SEWAGE DISPOSAL" as listed in Schedule ‘A’ Part-V representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES
1
2219631
-
Lump sum price worked out by the contractor for "AREA DRAINAGE " as listed in Schedule ‘A’ Part-VI representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES
1
7277870
-
Lump sum price worked out by the contractor for "RAIN WATER HARWESTING" as listed in Schedule ‘A’ Part-VII" representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES
1
138215
-
Lump sum price worked out by the contractor for "EXTERNAL WATER SUPPLY" as listed in Schedule ‘A’ Part-VIII representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price of prepriced by the MES
1
858288
-
Lump sum price worked out by the contractor for "EXTERNAL ELECTRIFICATION" as listed in Schedule ‘A’ Part-IX representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price of prepriced by the MES
1
3336209
-
Lump sum price worked out by the contractor for "PARADE GROUND, RECREATION GROUND AND COURTS" as listed in Schedule ‘A’ Part-X representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price of prepriced by the MES
1
1172103
-
Lump sum price worked out by the contractor for " COMPOUND WALL, CHAIN LINK FENCING AND GATE " as listed in Schedule ‘A’ Part-XI representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES
1
8200746
-
Lump sum price worked out by the contractor for " HOT WATER SUPPLY" as listed in Schedule ‘A’ Part-XII representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES
1
418376
-
Lump sum price worked out by the contractor for "REFRIGERATION AND COLD WATER SUPPLY" as listed in Schedule ‘A’ Part-XIII representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES
1
401626
-
Lump sum price worked out by the contractor for "SITE CLEARANCE, SITE DEVELOPMENT AND EARTH WORK" as listed in Schedule ‘A’ Part-XIV representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES
1
10416224
-
Lump sum price worked out by the contractor for " ADDN/ALTN OF EXISTING BUILDINGS & STRUCTURES (B/R)" as listed in Schedule ‘A’ Part-XV representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES
1
14378930
-
Lump sum price worked out by the contractor for " ADDN/ALTN OF EXISTING BUILDINGS & STRUCTURES (E/M)" as listed in Schedule ‘A’ Part-XVII representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES
1
1307772
-
Lump sum price worked out by the contractor for "DEMOLITION OF BUILDINGS & SHEDS" as listed in Schedule ‘A’ Part-XVII representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES
1
24646382
-
Sch 'A' Part-XVIII MISC ITEMS (TO BE QUOTED BY CONTRACTOR) Notes: (i) This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under column 5 signifies this fact only. (ii) Excavation and earth work except for the items which categorically includes for same shall be measured and paid separately under SCH A PART-XV (SITE CLEARANCE, SITE DEVELOPMENT AND EARTH WORK schedule).
-
-
-
POP EALSE CEILING FOR SCH A PART I BUILDING WORK (OFFICERS MESS & ADM BLOCK) M&Lfor POP false ceiling of approved design consisting of 10mm thick plaster of paris ceiling (Gyspsum anhydrous) board including GI frame work for 12mm seamless ceiling comprising of GI perimeter channel of 0.55 mm thick with two unequal flange of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre intermediate channel 0.5 mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900 mm centre to centre with GI cleat and Tee, expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having curved web of 50mm and flange of 26mm each with clips of 10.5mm fixed to intermediate channel with connecting clips across the intermediate channel of 457 mm centre to centre complete.
1334.2
-
-
INTERNAL WATER SUPPLY (SCH 'A' PART-II) S & F 15mm bore angle valve/cock cast copper alloy fancy type screwed down high pressure with cructh or butterfly handle screwed both ends for iron pipe or brass ferrule fixed. Make - CERA-F1012201, Jaguar - ARI- CHR-39053, KOHLER - K-80154IN-4-CP
115
-
-
S & F wall mixer/Diverter with diverter plate of Bathroom 3 in 1 system with provision for both hand & over head shower with 115mm long bend pipe ( for mixer) connecting legs & wall flangs complete all as specified. Make : CERA-F1012721, Jaguar-ALD-CHR065, ARI-CHR-39065NK, HINDWARE-K-22541IN-EP-CP
14
-
-
S & F chromium plated brass Bathtub Spout with Wall Flange (fancy type) suitable for 15mm bore pipe complete all as specified and directed. Make- CERA-F1012661, Jaguar-SPJ-CHR-429, HINDWARE-F-520009
16
-
-
INTERNAL ELECTRIFICATION (SCH 'A' PART-III) Supply and fixing SP 63 Amp rating, 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning
11
-
-
Supply and fix TV coaxial,1 module socket complete all as specified and as directed.
8
-
-
S&F Telephone socket(Jack Type) ,1 module RJ11 with shutter.
41
-
-
M&L for electrolyte grade solid annealed copper conductor,Jelly Field,Aluminium Foiled and Aluminium wire braided,RG59 (Foam).Cat Part No. WHOJTTKARG59 Make- Havells or equivalent
240
-
-
M&L for PVC insulated telephone cables for indoor applications confirming to technical specification G/WIR06/02 Cat Part No.WHTTATEA1P40 Make-Havells or equivalent
660
-
-
S & F for Highly efficient LED bulbs, 9 watt complete all as specified and directed. Make Bajaj/Havells/HPL
136
-
-
S & F of Sheet metal enclosure distribution board VTPN ,4 way, 415 volt, double door powder coated, protection class IP-54, isolated neutral bar, mechanical impact strength IK 09 suitable for mounting MCB & MCCB DBs confirming to IS-13032, IS-8632,BS5484 with min 200 Amp raiting copper bus bar and grouting, fixing on wall with nut boldts washers proper with PCC works complete all as specified and directed
6
-
-
RAIN WATER HARVESTING (SCH 'A' PART-VII) Borewell for rain water Harvesting all as specified and shown on drg : (a) Provision of trail bore by drilling with reverse rotary system 550mm bore upto 52 m depth incl all works pertaining to boring complete in all respect in aluvium soil/ strata incl hard stone / boulder etc.
(b) M&L for 150mm bore CPVC pipe assembly jointing, lowering in any position upto the reqd depth below given level incl jointing the pipe by solvent & screwing 04 Nos screws in each joint complete all as directed.
(c) Ditto as item (b) above but slotted pipe
(d) M& L for packing with Pea gravel of 4.6 mm to 8mm size of approved quality as ordered to pack arround the casing / slooted pipe in borewell all as directed.
(e) M&L 25 mm bore perforated CPVC pipe 52 mtr long for vent pipe
1
-
-
EXTERNAL WATER SUPPLY (SCH 'A' PART-VIII). M& L for cutting of existing pipeline of 100/150/80 mm dia for taking branch connection alongwith insertion of DI Tee and connecting material such as joint, nut bolts, etc all as required at site.
3
-
-
M&L for construction of brick stone masonary valve pit / chamber of size 900 mm x 600 mm x 1000 mm (internal dimensions) size 900 mm x 600 mm x 1000 mm (internal dimensions) all as shown in drawing No TD-573, including necessary excavation and earth work, PCC, plaster in CM 1:6 on inside and outside (above ground), MS angle iron 40 x 40x6.0 mm thick
4
-
-
All as per item No 23.02 but Chamber size 450 mm x 450 mm x 600 mm (internal dimensions)
4
-
-
EXTERNAL ELECTRIFICATION . (SCH 'A' PART-IX) Supply and fixing LED street light fitting 36 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with
IP 65/66 protection complete. Make : Phillips, Cat No BRP046 LED 36 CW MR S1 PSU GR 9405.
80
-
-
Supply and fixing poly carbonate junction box , weather and vermin proof of size 250X250X160 including provn of 4 Nos aluminium strip 25x3.15 mm size bus bar single phase and neutral suitabely mounted on bus bar insulators , including one No. MCB SP 6 Amps for light control,drilling of holes.Provn of suitable size of GI nuts, bolts, double washer and FI clamps of suitable size for taking connections and fixing on LT steel tubular poles complete with locking arrangement complete.
80
-
-
Supply install,testing and commissioning LT panel outdoor type, dust and vermin proof totally enclosed floor mounted factory made, "KIOSK TYPE" with sloping canopy fabricated out of steel sections, the door opening shall not be less than 150 degree. The construction of panel board shall be dust, vermin proof, IP 54 standard double shutter gears front and rear frame work and 3.15 mm thick MS sheet duly painted with powder coated over two coats of redoxide primer and made of 40 x 40 x 6 mm thick angle iron frame all as specfified including necessay foundation.bolt grouted in floor the panel suitable for 415 Volts, 50 C/s 3 phase and nutral system and shall be completed with aluminium bus bar of size ( current rating not less than 1.5 times of incoming MCCB ) with bus bar chamber,internal wiring with suitable size of PVC insulated copper cable comprising of following accessories:-(Main LTP No-01 )
1
-
-
Incoming :-
(a) MCCB 4 Pole 320 Amp thermal magnetic protection type, 36 KA Make : Legrand, Cat No - 4220-06, DPX3 630 - 01 No
(b) Indicating lamp - 3 Nos , Make : Schneider Cat No XA2EVQ1LC to 8LC.
(c) LED Multifunctional meter (Make: L&T) -01 No Cat No : DM6100
Outgoing :- (a) MCCB 3 pole 160 Amps thermal magnetic protection type, 36 KA, Make : Legrand, Cat No - 4200-87, DPX 160 - 01 No
b) MCCB 3 pole 200 Amps thermal magnetic protection type, 36 KA, Make : Legrand, Cat No - 4202-08, DPX 250 - 01 No (c) 3 pole power contactor, frame - 1, AC rating 12 A Cat No - LC1E1210 Make - Schneider
(d) Analog time switch, Make- Legrand, Cat No 4127-80 for SL control
-
-
-
Supply install,testing and commissioning LT panel outdoor type, dust and vermin proof totally enclosed floor mounted factory made, "KIOSK TYPE" with sloping canopy fabricated out of steel sections, the door opening shall not be less than 150 degree. The construction of panel board shall be dust, vermin proof, IP 54 standard double shutter gears front and rear frame work and 3.15 mm thick MS sheet duly painted with powder coated over two coats of redoxide primer and made of 40 x 40 x 6 mm thick angle iron frame
1
-
-
all as specfified including necessay foundation.bolt grouted in floor the panel suitable for 415 Volts, 50 C/s 3 phase and nutral system and shall be completed with aluminium bus bar of size ( current rating not less than 1.5 times of incoming MCCB ) with bus bar chamber,internal wiring with suitable size of PVC insulated copper cable comprising of following accessories:-. For LTP -4.
Incoming
(a) MCCB 4 pole 160 Amps thermal magnetic protection type, 25 KA, Make : Legrand, Cat No - 4200-57, DPX 160 - 01 No
(b) Indicating lamp - 3 Nos , Make : Schneider Cat No XA2EVQ1LC to 8LC
(c) LED Multifunctional meter (Make: L&T) -01 No Cat No : DM6100
Out Going
(a) MCCB 3 Pole 63 Amp thermal magnetic protection type, 25 KA DPX3 160 Legrand, Cat No 4200-43 - 02 No (Single Offr accn + LTP - 08)
(b) MCCB 3 Pole 40 Amp thermal magnetic protection type, 25 KA DPX3 160 Legrand, Cat No 4200-42 - 02 No ( Servant Qtr + SL)
(c) MCCB 3 pole 125 A thermal magnetic protection type, 25 KA DPX3 160, Legrand, Cat No 4200-06 - 01 (Offr Mess)
(d) MCB DP 16Amp - 01 No ( Garage)
(e) 3 pole power contactor, frame - 1, AC rating 12 A Cat No - LC1E1210 Make - Schneider (f) Analog time switch, Make- Legrand, Cat No 4127-80 for SL control
-
-
-
Supply install,testing and commissioning LT panel outdoor type, dust and vermin proof totally enclosed floor mounted factory made, "KIOSK TYPE" with sloping canopy fabricated out of steel sections, the door opening shall not be less than 150 degree. The construction of panel board shall be dust, vermin proof, IP 54 standard double shutter gears front and rear frame work and 3.15 mm thick MS sheet duly painted with powder coated over two coats of redoxide primer and made of 40 x 40 x 6 mm thick angle iron frame all as specfified including necessay foundation.bolt grouted in floor the panel suitable for 415 Volts, 50 C/s 3 phase and nutral system and shall be completed with aluminium bus bar of size ( current rating not less than 1.5 times of incoming MCCB ) with bus bar chamber,internal wiring with suitable size of PVC insulated copper cable comprising of following accessories:-. For LTP - 8
Incoming
(a) MCCB 4 Pole 63 Amp thermal magnetic protection type, 16 KA DPX3 160 Legrand, Cat No 4200-13 - 01 No
1
-
-
(b) Indicating lamp - 3 Nos , Make : Schneider Cat No XA2EVQ1LC to 8LC
(c) LED Multifunctional meter (Make: L&T) -01 No Cat No : DM6100
Out Going
(a) MCB 2 Pole 16 Amp, 'C' Curve, 10 KA, Legrand, Cat No 4086-33 - 10 No
-
-
-
Supply install,testing and commissioning LT panel outdoor type, dust and vermin proof totally enclosed floor mounted factory made, "KIOSK TYPE" with sloping canopy fabricated out of steel sections, the door opening shall not be less than 150 degree. The construction of panel board shall be dust, vermin proof, IP 54 standard double shutter gears front and rear frame work and 3.15 mm thick MS sheet duly painted with powder coated over two coats of redoxide primer and made of 40 x 40 x 6 mm thick angle iron frame all as specfified including necessay foundation.bolt grouted in floor the panel suitable for 415 Volts, 50 C/s 3 phase and nutral system and shall be completed with aluminium bus bar of size ( current rating not less than 1.5 times of incoming MCCB ) with bus bar chamber,internal wiring with suitable size of PVC insulated copper cable comprising of following accessories:-. For LTP -3.
1
-
-
Incoming
(a) MCCB 4 pole 200 Amps thermal magnetic protection type, 25 KA, Make : Legrand, Cat No - 4202-18, DPX 250 - 01 No
(b) Indicating lamp - 3 Nos , Make : Schneider Cat No XA2EVQ1LC to 8LC
(c) LED Multifunctional meter (Make: L&T) -01 No Cat No : DM6100
Out Going
(a) MCCB 3 Pole 100 Amp thermal magnetic protection type, 25 KA DPX3 160 Legrand, Cat No 4200-45 - 01 No (LTP - 06)
(b) MCCB 3 pole 160 A thermal magnetic protection type, 25 KA DPX3 160, Legrand, Cat No 4200-47 - 01 (Adm Bldg)
(c) MCCB 3 Pole 40 Amp thermal magnetic protection type, 16 KA DPX3 160 Legrand, Cat No 4200-02 - 02 No (SAA Stores + Old Guard House)
(d) MCB 2 Pole 16 Amp, 'C' Curve, 10 KA, Legrand, Cat No 4086-33 - 03 No
(e) 3 pole power contactor, frame - 1, AC rating 12 A Cat No - LC1E1210 Make - Schneider (f) Analog time switch, Make- Legrand, Cat No 4127-80 for SL control
-
-
-
Supply install,testing and commissioning LT panel outdoor type, dust and vermin proof totally enclosed floor mounted factory made, "KIOSK TYPE" with sloping canopy fabricated out of steel sections, the door opening shall not be less than 150 degree. The construction of panel board shall be dust, vermin proof, IP 54 standard double shutter gears front and rear frame work and 3.15 mm thick MS sheet duly painted with powder coated over two coats of redoxide primer and made of 40 x 40 x 6 mm thick angle iron frame all as specfified including necessay foundation.bolt grouted in floor the panel suitable for 415 Volts, 50 C/s 3 phase and nutral system and shall be completed with aluminium bus bar of size ( current rating not less than 1.5 times of incoming MCCB ) with bus bar chamber,internal wiring with suitable size of PVC insulated copper cable comprising of following accessories:-. For LTP -6
1
-
-
Incoming (a) MCCB 4 Pole 100 Amp thermal magnetic protection type, 25 KA DPX3 160 Legrand, Cat No 4200-55 - 01 No (b) Indicating lamp - 3 Nos , Make : Schneider Cat No XA2EVQ1LC to 8LC
(c) LED Multifunctional meter (Make: L&T) -01 No Cat No : DM6100
Out Goingm (a) MCCB 3 Pole 63 Amp thermal magnetic protection type, 25 KA DPX3 160 Legrand, Cat No 4200-43 - 01 No (b) MCB 2 Pole 16 Amp, 'C' Curve, 10 KA, Legrand, Cat No 4086-33 - 05 No
-
-
-
Supply install,testing and commissioning LT panel outdoor type, dust and vermin proof totally enclosed floor mounted factory made, "KIOSK TYPE" with sloping canopy fabricated out of steel sections, the door opening shall not be less than 150 degree. The construction of panel board shall be dust, vermin proof, IP 54 standard double shutter gears front and rear frame work and 3.15 mm thick MS sheet duly painted with powder coated over two coats of redoxide primer and made of 40 x 40 x 6 mm thick angle iron frame all as specfified including necessay foundation.bolt grouted in floor the panel suitable for 415 Volts, 50 C/s 3 phase and nutral system and shall be completed with aluminium bus bar of size ( current rating not less than 1.5 times of incoming MCCB ) with bus bar chamber,internal wiring with suitable size of PVC insulated copper cable comprising of following accessories:-. For LTP -7
1
-
-
Incoming (a) MCCB 4 Pole 63 Amp thermal magnetic protection type, 25 KA DPX3 160 Legrand, Cat No 4200-53 - 01 No (b) Indicating lamp - 3 Nos , Make : Schneider Cat No XA2EVQ1LC to 8LC
(c) LED Multifunctional meter (Make: L&T) -01 No Cat No : DM6100
Out Going (a) MCCB 3 Pole 40 Amp thermal magnetic protection type, 16 KA DPX3 160 Legrand, Cat No 4200-02 - 02 No ( BCH + MT Office)
(b) MCB 2 Pole 16 Amp, 'C' Curve, 10 KA, Legrand, Cat No 4086-33 - 13 No (Garage) (c) MCB 3 Pole 16 Amp, 'C' Curve, 10 KA, Legrand, Cat No 4086-55 - 02 No (Car Washing + Longe wala gate)
-
-
-
Supply install,testing and commissioning LT panel outdoor type, dust and vermin proof totally enclosed floor mounted factory made, "KIOSK TYPE" with sloping canopy fabricated out of steel sections, the door opening shall not be less than 150 degree. The construction of panel board shall be dust, vermin proof, IP 54 standard double shutter gears front and rear frame work and 3.15 mm thick MS sheet duly painted with powder coated over two coats of redoxide primer and made of 40 x 40 x 6 mm thick angle iron frame all as specfified including necessay foundation.bolt grouted in floor the panel suitable for 415 Volts, 50 C/s 3 phase and nutral system and shall be completed with aluminium bus bar of size ( current rating not less than 1.5 times of incoming MCCB ) with bus bar chamber,internal wiring with suitable size of PVC insulated copper cable comprising of following accessories:- (Main LTP No-02 )
1
-
-
Incoming (a) MCCB 4 Pole 400 Amp thermal magnetic protection type, 36 KA Make : Legrand, Cat No - 4220-07, DPX3 630 - 01 No
(b) Indicating lamp - 3 Nos , Make : Schneider Cat No XA2EVQ1LC to 8LC
(c) LED Multifunctional meter (Make: L&T) -01 No Cat No : DM6100
Outgoing (a) MCCB 3 pole 200 Amps thermal magnetic protection type, 36 KA, Make : Legrand, Cat No - 4202-08, DPX 250 - 01 No (LTP -02)
(b) MCCB 3 pole 160 Amps thermal magnetic protection type, 36 KA, Make : Legrand, Cat No - 4200-87, DPX 160 - 01 No (LTP - 01)
(c) MCCB 3 Pole 40 Amp thermal magnetic protection type, 25 KA DPX3 160 Legrand, Cat No 4200-42 - 01 No (LTP - 5)
(d) 3 pole power contactor, frame - 1, AC rating 12 A Cat No - LC1E1210 Make - Schneider
(e) Analog time switch, Make- Legrand, Cat No 4127-80 for SL control
-
-
-
Supply install,testing and commissioning LT panel outdoor type, dust and vermin proof totally enclosed floor mounted factory made, "KIOSK TYPE" with sloping canopy fabricated out of steel sections, the door opening shall not be less than 150 degree. The construction of panel board shall be dust, vermin proof, IP 54 standard double shutter gears front and rear frame work and 3.15 mm thick MS sheet duly painted with powder coated over two coats of redoxide primer and made of 40 x 40 x 6 mm thick angle iron frame all as specfified including necessay foundation.bolt grouted in floor the panel suitable for 415 Volts, 50 C/s 3 phase and nutral system and shall be completed with aluminium bus bar of size ( current rating not less than 1.5 times of incoming MCCB ) with bus bar chamber,internal wiring with suitable size of PVC insulated copper cable comprising of following accessories:-. For LTP -1
1
-
-
Incoming
(a) MCCB 4 pole 160 Amps thermal magnetic protection type, 25 KA, Make : Legrand, Cat No - 4200-57, DPX3 160 - 01 No
(b) Indicating lamp - 3 Nos , Make : Schneider Cat No XA2EVQ1LC to 8LC
(c) LED Multifunctional meter (Make: L&T) -01 No Cat No : DM6100Out Going
(a) MCCB 3 Pole 40 Amp thermal magnetic protection type, 25 KA DPX3 160 Legrand, Cat No 4200-42 - 01 No ( LTP -5)
(b) MCCB 3 Pole 25 Amp thermal magnetic protection type, 16 KA DPX3 160 Legrand, Cat No 4200-01 - 02 No ( FWC + ORI )
(c) MCCB 3 Pole 16 Amp thermal magnetic protection type, 16 KA DPX3 160 Legrand, Cat No 4200-00 - 02 No ( Religious Hall + Unit shop)
(d) MCCB 3 Pole 80 Amp thermal magnetic protection type, 25 KA DPX3 160 Legrand, Cat No 4200-44 - 01 No ( Trademen Shop)
(e) 3 pole power contactor, frame - 1, AC rating 12 A Cat No - LC1E1210 Make - Schneider (f) Analog time switch, Make- Legrand, Cat No 4127-80 for SL control
-
-
-
Supply install,testing and commissioning LT panel outdoor type, dust and vermin proof totally enclosed floor mounted factory made, "KIOSK TYPE" with sloping canopy fabricated out of steel sections, the door opening shall not be less than 150 degree. The construction of panel board shall be dust, vermin proof, IP 54 standard double shutter gears front and rear frame work and 3.15 mm thick MS sheet duly painted with powder coated over two coats of redoxide primer and made of 40 x 40 x 6 mm thick angle iron frame all as specfified including necessay foundation.bolt grouted in floor the panel suitable for 415 Volts, 50 C/s 3 phase and nutral system and shall be completed with aluminium bus bar of size ( current rating not less than 1.5 times of incoming MCCB ) with bus bar chamber,internal wiring with suitable size of PVC insulated copper cable comprising of following accessories:-. For LTP -5 Incoming
(a) MCCB 4 Pole 40 Amp thermal magnetic protection type, 16 KA DPX3 160 Legrand, Cat No 4200-12 - 01 No
(b) Indicating lamp - 3 Nos , Make : Schneider Cat No XA2EVQ1LC to 8LC
(c) LED Multifunctional meter (Make: L&T) -01 No Cat No : DM6100
1
-
-
Out Going
(a) MCCB 3 Pole 16 Amp thermal magnetic protection type, 16 KA DPX3 160 Legrand, Cat No 4200-00 - 01 No ( Drying & Ironing)
(b) MCB 2 Pole 16 Amp, 'C' Curve, 10 KA, Legrand, Cat No 4086-33 - 4 No (Car shed - 01 No + Scooter shed - 01 No + Dhobi Ghat - 02 Nos) (c) 3 pole power contactor, frame - 1, AC rating 12 A Cat No - LC1E1210 Make - Schneider
(d) Analog time switch, Make- Legrand, Cat No 4127-80 for SL control
-
-
-
Supply install,testing and commissioning LT panel outdoor type, dust and vermin proof totally enclosed floor mounted factory made, "KIOSK TYPE" with sloping canopy fabricated out of steel sections, the door opening shall not be less than 150 degree. The construction of panel board shall be dust, vermin proof, IP 54 standard double shutter gears front and rear frame work and 3.15 mm thick MS sheet duly painted with powder coated over two coats of redoxide primer and made of 40 x 40 x 6 mm thick angle iron frame all as specfified including necessay foundation.bolt grouted in floor the panel suitable for 415 Volts, 50 C/s 3 phase and nutral system
1
-
-
and shall be completed with aluminium bus bar of size ( current rating not less than 1.5 times of incoming MCCB ) with bus bar chamber,internal wiring with suitable size of PVC insulated copper cable comprising of following accessories:-. For LTP -2
Incoming
(a) MCCB 4 pole 200 Amps thermal magnetic protection type, 25 KA, Make : Legrand, Cat No - 4202-18, DPX3 250 - 01 No (b) Indicating lamp - 3 Nos , Make : Schneider Cat No XA2EVQ1LC to 8LC
(c) LED Multifunctional meter (Make: L&T) -01 No Cat No : DM6100
Out Going
(a) MCCB 3 Pole 25 Amp thermal magnetic protection type, 25 KA DPX3 160 Legrand, Cat No 4200-41 - 02 No (S/L JCO)
(b) MCCB 3 Pole 16 Amp thermal magnetic protection type, 16 KA DPX3 160 Legrand, Cat No 4200-00 - 04 No ( S/L 01 JCO + Engr Store + Def Store + Old bldg)
(c) MCCB 3 Pole 80 Amp thermal magnetic protection type, 25 KA DPX3 160 Legrand, Cat No 4200-44 - 01 No ( JCO's Mess)
(d) MCCB 3 Pole 63 Amp thermal magnetic protection type, 25 KA DPX3 160 Legrand, Cat No 4200-43 - 01 No (MI Room)
(e) MCB 2 Pole 16 Amp, 'C' Curve, 10 KA, Legrand, Cat No 4086-33 - 4 Nos (Car shed - 01 No + Scooter shed - 01 No + Garage for Amb - 01 No +Car shed/Scooter shed - 01 No ) (f) 3 pole power contactor, frame - 1, AC rating 12 A Cat No - LC1E1210 Make - Schneider
(g) Analog time switch, Make- Legrand, Cat No 4127-80 for SL control
-
-
-
Taking down old Cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor off sizes from existing site
450
-
-
Dismentling street light bracket off sizes
4
-
-
Dismantling and taking down LT Feeder Pillar Box off size
5
-
-
Dismantling and taking down Outdoor distribution Box off size
70
-
-
Dismantling and taking down transformers 160 KVA to 500 KVA and deposit to MES store yard or keeping in safe custody for re-installation
3
-
-
PARADE GROUND, RECREATION GROUND AND COURTS (SCH 'A' PART-X (SYNTHETIC FLOOR / MAT FOR BASKET BALL & VOLLEY BALL COURTS) M & L for antifungal, anti microbial and U/V resistant comprising of PVC wear resisting coat thickness of 3.5mm to 8mm over of fiber-glass reinforced layer with PVC foaming buffer layer of thickness 4.5mm for good performance in rebounding & absorbing shock.
1414.9
-
-
REFRIGERATION AND COLD WATER SUPPLY (SCH 'A' PART -XIII) Supply and fix refrigerator, electric driven (single phase),direct cool single door 5 star refrigerator with base drawer with smart inverter compressor capacity not less than 185 Litres .
4
-
-
Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity not less than 2.0KVA
12
-
-
Supply and fix desert cooler electric driven (single phase), having nominal air flow capacity of 4000 CuM per hour (or nearest size).Steel body
40
-
-
ADDN/ALTN OF EXISTING BUILDINGS & STRUCTURES (B/R) : SCHEDULE 'A' PART -XV (SCH 'A' PART -XVI) M & L for providing 5-7mm thick screed bed of chemical adhresive of approved make for laying floor finishes i,e floor tile etc. complete all as specified and as directed by Engr-in-Charge.
165
-
-
Taking down existing water proofing roof treatment of any description cleaning the surface by hacking to received plaster complete all as specified and removing demolised material outside MOD land.
1232
-
-
S & F fibre reinforced UV resistant elastomeric liquid applied waterproofing & heat reflective coating with acrylic polymers and polyester/glass fibres after scraping and properly cleaning the surface to remove loose perticles with wire brushes complete or as directed water proofing treatment shall be in three coats over a coat of primer and as per manufacturers instructions complete all as specified and directed.
1257
-
-
M & L for retrieving vegetation growth/plants from wall roofs, chajja upto double storey height incl taking out deep roots and pouring Hcl acid and making good the distrubance surfaces with CM 1:4 incl all means required at site complete all as specified and as directed by Engr-in-Charge
60
-
-
ADDN/ALTN OF EXISTING BUILDINGS & STRUCTURES (E/M) : SCHEDULE 'A' PART -XVI Taking down of existing UNSV sub main wiring any size incl PVC/steel conduit complete and making good to disturbed surfaces.
450
-
-
Taking down of existing UNSV DBs any size
25
-
-
Supply MCBs, 10 KA rupturing capacity, IS-8828 marked, DP 10 Amps and fixing in DBs (DBs shall be measured and paid separately :-
10
-
-
All as per items No 61.00 but DP 20 Amps
20
-
-
All as per items No No 61.00 but 4P 25 Amps
5
-
-
All as per items No No 61.00 but SP 6 Amps
100
-
-
All as per items No No 61.00 but SP 10 Amps
40
-
-
All as per items No No 61.00 but SP 20 Amps
20
-
-
DEMOLITION OF BUILDINGS & SHEDS : SCHEDULE 'A' PART -XVII Taking down carefully by carefully unscrewing serviceable/unserviceable DBs,any sizes 415 volt complete with bus bar and rails for easy mounting of MCBs complete with from boards and disconnecting from incoming and outgoing.
185
-
-
Taking down Sub main wiring of any sizes
350
-
-
ARBOURICULTURE WORK Laying of lawns including ploughing leveling breaking of clods manuring & removal of stones etc. (cost of manure or extra good earth to be paid separately) Maintenance of lawns for 30 days more till the grass forms a thick lawns free from weeds & fit for moving in the duration of planting if lawn die some where the contractor will replant it at his own cost. In rows 5 Cms. Apart in either direction
100
-
-
Supply of Different flower plants 900mm to 1500mm at site including loading / unloading & transportation etc.complete.
50
-
-
Supply of Different varieties of shrubs 600mm to 900mm at site including loading / unloading & transportation etc.complete.
50
-
-
Supply of Different varieties of climbers 900mm to 1500mm at site including loading / unloading & transportation etc.complete.
50
-
-
Supply of different varieties of palms in polyethylene bags / earthen pots according to height growth & age of the plant at site including loading / unloading & transportation etc .complete
150
-
-
Supply & planting of shady plants (Neem, Peepal, Goolar, Jamun, Imli or other specified) along including the following activities :-
(a) Preparation of soil including & removing of unwanted shrubs removal of stones & garbage.
(b) Supply of plant at site of two years of age & height more than 1.50Mtr.
(c) Supply of dry manure (Farm yard manure.
(d) Supply of insecticides.
(e) Digging of pits size 60x60x60 Cms.
200
-
-
Supply & planting of ornamental plants (Kachnar, Amaltas, Gulmohar, Arjun, Jacranda etc. or other specified) along including the following activities :-
(a) Preparation of soil including cleaning & removing of unwanted shrubs removal of stones & garbage.
(b) Supply of plant at site of two years of age & height more than 1.50Mtr.
(c) Supply of dry manure (Farm yard manure organic).
(d) Supply of insecticides.
(e) Digging of pits size 60x60x60 Cms. including removal of stones, Manu-ring application of insecticides & watering at least 15 Liter per plant after planting.
(f) Watering to plants.
100
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%