Military Engineer Services Tender

M&L for preparation of new plastered and applying two coats of weather proof exterior emulsion paint (Apex ultima or equivalent) over a coat of primer over 2 mm thick wall care putty complete all as specified and directed by Engineer-in-charge.

Supply and fix bib taps, cast copper alloyfancy type chormium plated. with Capastan head screwed down screwdd for iron pipe of brass ferrule, and fixed in 15 mm bore dia of pipe complete all as specified and directed by Engr-in-charge.

Supply and fix pillar taps swan neck, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in 15mm dia bore pipe complete all as specified and directed by Engr-in-charge.

S&F in repair CP brass stop/angle valve fancy type 15 mm bore cast copper alloy screwed down high pressure fancy type with long shank and cup fixed all as specified.

S&F in repair, shower rose, 125 mm size, brass chromium plated with sweivel joint all as directed.

S & F in repair 3-in-1 wall CP mixer hot & cold, fancy type water screwed down for iron pipe of 15 mm bore.

S&F in repair central hole basin mixer for hot and cold water supply, cast copper alloy, chromium plated screwed down for iron pipes, including necessary fittings & fixtures etc complete all as specified and directed by Engneer -in-Charge

S&F in repair stainless steel kitchen plate rack, made out of 1.00mm thick sheet for size 900x1200x200mm fixed on wall with screw, washers complete all as specified and directed by Engneer -in-Charge

S&F in repair health faucet with CP flexible cord fixed on wall complete all as specified and directed by Engneer -in-Charge

Supply only PVC waste pipe 32mm bore 60 cm long complete complete all as specified and directed by Engineer in Charge

S&F In repair plastic water closet seat, white closed pattern with flat bottom,and cover and mild steel chromium plated or aluminium hinging device seat and cover for water closet (European type) complete all as specified.

S&F in repair CP towel ring of size 150 mm decorative type fixed to walls complete all as specified and directed by Engneer -in-Charge

S&F in repairs white vitrieous china wash down WC (Pedestal pattern) of size 630mm X 350mm X 790mm with fixing bolt, plastic water closed seat cover, white closed pattern with flat bottom, and cover with aluminium hinging device, including all connection complete all as specified and directed by Engr-in-charge.

Supply and fixing in repairs PVC valve less, syphonic action type flushing cistern,10 ltrs capacity low level, white, with inlet ball valve, float, handle and telescopic pipe and connection to pipe and flush pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern complete all as specified and directed by Engr-in-charge.

S & F in repair cabinet mirror of size 400mm X 500 mm fixed with PVC rawl plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engineer-in-Charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Virified Ceramic tiles 8 to10 mm thick (square/ rectangular) light shed polished, area of each tiles not exceeding 0.36 sqm, 13086 etc. over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor all as specified and directed.

M&L for Vitrified Ceramic tiles 8 to10 mm thick (square/ rectangular) light shade polished, area of each tiles not exceeding 0.36 sqm,on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor complete all as specified and directed by Engneer -in-Charge

M&L for glazed ceramic coloured tiles of size 450 x 300 x 7 mm thick on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match the floor all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded and pointed in any mortar complete all as specified and as directed.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding to edges of stone slabs one edge complete all as specified and directed by Engr-in-charge.

Taking up or down steel tubing of size 15 mm bore dia and connections complete all as specified and directed.

All as per item No 25 but 20 mm dia pipe

S&F 15 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling complete all as directed.

All as per item No 27 but 20 mm dia pipe

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm in thickness (below or above ground level) all as specified.

M&L for 75mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base below floors all specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;

Taking down chowkhats or frames n.exc 1.5 sq. m each with shutters (without taking off shutters from the frame) complete all specified and directed.

Taking down chowkhats or frames exc 1.5 sq. m but n.exc 4.0 sq. m each with shutters (without taking off shutters from the frame) complete all specified and directed directed.

Taking down existing shutter and refixing in same opening shutters of any description exc 1.0 Sqm but not exc 2.0 Sqm each all as specified and directed. (Note:- 'Refixing' includes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc.)

S&F for powder coated aluminium frame for doors, windows, ventilators and aluminium partition with one or more rebates including jointing cleats glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete with locking arrangements for fixing with powder coating on aluminium sections, minimum thickness of poweder coating shall be 50 micron as per the specification. The top and bottom horizontal members and vertical members adjacent to wall shall be fixed with floor, ceiling, walls and cills where required and fixed with the help of rawl plugs and screws or with fixing clips or with expansion hold plate fastners. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically whereever required complete in all respect all as specified & directed by Engr-in-Charge. Make of Al Section : Jindal / Hindalco / NALCO

S & F for Aluminium anodised (Powder coated) Three track sliding window frame with shutters (two glazed and one gauged shutter) including all necessary joining cleats, hold fast, rubber gasket, snap beading and locking arrangements fixed with screws to wall etc. complete and glazing with 5 mm thick tinted glass to aluminium frame work using rubber gasket and including stainless steel wire cloth of 0.36mm dia & average width of aperture 1.40mm with staple or suitable fillets wire mesh fitted with screws and washers etc with the following section of frame and shutter (A) Sections for frame (i) Top and verticals 92 x 29.50 x 1.30 mm thick (ii) Bottom 92 x 29.50 x 1.20 mm thick. (B) Sections for shutter (i) 'A' section 39 x 20 x 1.50 mm thick (ii) 'Interlock' section 39 x 20 x 1.50 mm thick(iii) 'H' section 41 x 20 x 1.10 mm thick Make: Jindal or equivalent sections of Hindalco.

S & F powder coated standard aluminium anodised grill size of mesh 75 mm x 75 mm and 8 mm thick section using U channel 25 x 12 mm all as specified and directed

Supply and fixing of Fibre glass Reinforced plastic (FRP) door frame of required built in colour in three legged of cross-section 90mm x 45mm having single ribate of 32mm x 15mm to recieve shutter of 30mm thick including laminated door frame moulded with fire retardant grade unsaturated polyster resin and chopped strand mat(CSM) also door frame laminated shall be 2mm thick and shall be filled with suitable wooden block of 2nd class hard wood in all three legs frame shall be covered with fibreglass from all sides MS stay flat iron 25mm x 3mm shall be provided at the bottom to steady the frame complete all as specified and as directed by Engineer-in- charge.

Supply and fixing of 30 mm thick glass fibre reinforced plastic (FRP) paneled doorshutter conferming to IS:14856-2000 of required colour and made with fire retardant grade unsaturated polyster resin,moulded to 3mm thick FRP laminated for forming hollow rails and style with suitable second class hardwood timber block inside at required places for fixing of fittings,cast molithically with 5mm thick FRP laminated for panels including fixing to frames,complete all as specified and as directed by Engineer-in- charge.

S&F for framed work as in chowkats of doors windows of angle iron ,gates or other section with gusset plates, rails, braces etc conforming to Gde Fe 410-0 or Fe 310-0 complete all as specified and directed by Engineer-in-Charge.

S&F for 35 mm thick 2nd class hard wood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engr-in-charge.

S&F for 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) all as directed.

S&F for 100 mm long butt hinge, extruded aluminium alloy with galvanised mild steel hinge pin, anosied and fixed type B-21 complete all as specified and directed by Engr-in-charge.

S&F for 200 mm long aluminium anodised barrel tower bolt, of extruded sections complete all as specified and directed by Engr-in-charge.

S&F for 125 mm long aluminium anodised handle, cast type complete all as specified and directed by Engr-in-charge.

Supply and fixing 100mm long butt hinges mild steel medium weight cold rolled including necessary welding etc. to steel frame complete all as specified & directed by Engineer-in-charge.

S&F for 300mm long aluminium alloy, anodised, sliding door bolt type not less than 16mm dia fixed all as specified & directed by Engr-in- charge.

S&F for 300mm ordinary rat tail rod pattern springs including roller and roller plate complete mild steel fixed complete all as specified and directed by Engr-in-Charge.

S&F for stainless steel wire cloth 0.63 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed by Engr-in-charge.

M&L for preparation of old painted wooden surface of any description not otherwise described over 10 cm width or girth and apply one coat of synthetic enamel paint all as specified.

S&F in repair kitchen sinks made of stainless steel 1mm thick with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to waste pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-in-Charge.

S&F in repair looking mirror of selected quality of size 600 mm X 450 mm with bevelled edge mounted 6 mm thick commercial plywood and aluminium channel of required size fixed to wooden plugs with chromium plated brass screws and cup washers all as directed.

S&F in repair chromium plated stainless steel fancy type soap dish complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repair glass corner shelf with CP brackets and CP railingcomplete all as specified and directed by Engineer-in-Charge.

Dismantling of Brick tiles or terracing tiles, single layer on roofs complete all as specified and as directed by engineer-in-Charge.

Demolition mud in roofs, any thickness, including plastering and leeping complete all as specified and directed.

M&L 40mm thick brick tiles laid flat joints grouted flush in cement mortar (1:3) bedded in 15mm th cement morter (1:6) mixed with 5% of curde oil by weight of cement complete all as specified and directed by Engr-in-Charge.

All as per item No 57 except tiles

M&L for Roof treatment to RCC roof as follows:- (a) Cleaning the roof surfaces thoroughly using wire brusehes to remove sharp projections, cleaning joints, washing, drying and removing all dirt/dust to receive concrete padding/plaster etc. (b) Providing 15 mm thick screed bed or bedding layer of cement mortar (1:4) with WPC, finished even and smooth without using extra cement. (c) Providing one coat of approved bituminous primer @100 gms per sqm, over dried plastered surface. (d) Laying 3 mm thick APP membrane,(mineral finish) reinforced with non woven polyster fabric, by torch application. The overlapping while torching shall be 75 mm on longitudinal direction and 100 mm on the transverse direction complete all as specified and directed by E-in-Charge. Make : STP Dr Fixit/Pidilite, Texsa India Ltd/Tikitar Dansona/Bengal Bitumen/ M/S TORCHTAR MEMBRANE Notes : (i) All joints and change in directions should be covered wih cement mortar (1:3) mixed with SBR latex @ 200 ml/bag of cement/as per site reqmt and cured well before laying membrane by torching. (ii) All angles and abuttments should be sealed well with extra care to ensure full bondage. (iii) Water proofing treatment shall be got carried out by approved authorised applicator of manufacturer only. The name of firm shall be got approved from GE before carrying out the wk. (iv) The independent testing of membrane for technical parameters given in particular specifications shall be carried out from Govt approved labs having fascilities for testing of membrane. (v) The guarnatee of treatment shall be for min 10 yrs reckoned from date of completion of whole wk.

M&L PCC 1:2:4 type B-1, using 20mm graded stone aggregate as in roof kerbs or mud stops, and like rounded or chamfered on edges including necessary form work etc complete all as specified & directed by Engr-in-Charge.

Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks etc., Note: measured overalll as fixed along the cente line over fittings and accessories)

S&F 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls all as directed.

S&F in repair for Rotational moulded polythene water storage tank 1000 ltr capacity vertical with closed top, ISI marked hoisted and fixed in position all as specified in SSR part-I. including 20 mm bore PTMT float valve, connection nipple 2 Nos complete all as specified and directed..

M & L for 50 mm thick cement concrete type B-1, 1:2:4 (20 mm grade aggregate) as sub base/levelling course in floor, paving etc finishes even after fair complete all as specified and directed by Engineer-in-Charge.

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ