Military Engineer Services Tender
If you're looking for Rajasthan tenders online and are tired of typing tender ID over and again or going through the cumbersome government websites for it, you are in luck. We have collated every Eproc Rajasthan tender on BidAssist. And for any queries related to an e-tender Rajasthan, like bidding process, registration process, etc., are explained below. Read on.
Costs
EMD
₹ 60,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2022_MES_557870_1Bid Award Id
ViewTender No
GE (N) BKN TOKEN NO 57 /2022-2023Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
(b) Rotor sleeve
8
-
-
(c) Water seal
8
-
-
(d) Thrust bearing Make- NBC/SKF
8
-
-
(e) Housing upper
4
-
-
(f) Housing lower
4
-
-
(g) Cable seal
10
-
-
(h) Thrust plate
6
-
-
(j) Coupling S/S
4
-
-
(k) Key for coupling
4
-
-
(l) LNK bolt S/S
8
-
-
(m) Revolving disc
8
-
-
(n) Seal bush
5
-
-
(p) Sand guard
4
-
-
(q) Rotor
4
-
-
(r) Stator
4
-
-
Opening, reassembling and testing of submersible pump of capacity 2000 to 6000 GPH including replacement of the worn out spare parts as mentioned under respective item no (5) here in after. Make of pump: CALAMA/SABAR/KSB/BED FORD GARVIN/KIRLOSKAR.
7
-
-
Supply only the following spare parts for submersible pump cap 2000 to 6000 GPH
(a) Stage bowl
7
-
-
(b) Impeller GM.
7
-
-
(c) Pump shaft S/S (single stage)
4
-
-
(d) Hook bolt (Upper & lower)
4
-
-
(e) GM neck ring
7
-
-
(f) Key for pump shaft (Each stage)
7
-
-
(g) Distance sleeve
7
-
-
Supply and fixing to the extant required replacement under item No 1 here in before 80 mm bore GI pipe (length of six meter for each job) heavy grade with flange not less than 12mm thick duly drilled holes on each end, screwed and welded with necessary packing/jointing nut bolts & washers with four MS flat of size 12 x 6 mm support on each flange with suitable cut/opening for cable complete all as specified and as directed by Engineer-in-Charge. Make : Jindal/Prakash Surya/ TATA
30
-
-
Taking down of defective induction motor of the following capacity and make from the foundation, disconnecting the electric connecting coupling pulley, and transporting to work shop cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding with solid copper conductor ( winding wire) complete including varnishing, drying, ovening, overhauling, greasing and fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and as directed by Engineer-in-Charge. (a) 75 HP capacity, 03 phase 415 volt 50 HZ
1
-
-
(b) 60 HP capacity, 03 phase, 415 volt 50 Hz
1
-
-
(c) 50 HP capacity,03 phase, 415 volt 50 Hz
1
-
-
(d) 40 HP capacity, 03 phase, 415 volt 50 HZ
5
-
-
(e) 30 HP capacity, 03 phase, 415 volt 50 HZ
2
-
-
(f) 25 HP capacity, 03 phase, 415 volt 50 HZ
2
-
-
(g) 20 HP capacity, 03 phase, 415 volt 50 HZ
4
-
-
(h) 15 HP capacity, 03 phase, 415 volts 50 HZ
3
-
-
(j) 10 HP capacity, 03 phase, 415 volts 50 HZ
3
-
-
(k) 7.5 HP capacity, 03 phase, 415 volts 50 HZ
2
-
-
(l) 5 HP capacity, 03 phase, 415 volts 50 HZ
1
-
-
(m) 3 HP capacity, 03 phase, 415 volts 50 HZ
1
-
-
(n) 2 HP capacity, 03 phase, 230 volts 50 HZ
2
-
-
(o) 1.5 HP capacity, 01 phase, 230 volts 50 HZ
1
-
-
(p) 1 HP capacity, 01 phase, 230 volts 50 HZ
4
-
-
(q) 0.5 HP capacity, 01 phase, 230 volts 50 HZ
3
-
-
Taking down from foundation base frame by disconnecting suction/delivery lines and coupling, opening including dismantling of centrifugal pump set of capacity 75 HP model DSM 100-36, and replacement of worn out spare parts as mentioned under respective item no-09 here in after and re-assembling, installation in same location including testing aa as directed. Make : Kirloskar
1
-
-
Supply only the following spare parts for centrifugal pump of 75 HP capacity model DSM 100-36 required to be replaced under item No 8 above, Make:- Kirloskar (a) Inter stage ring
1
-
-
(b) Gland Cap CI with nut bolt complete
2
-
-
(c) Wear ring CI
2
-
-
(d) Shaft Sleeve Bronze
2
-
-
(e) Shaft Sleeve Nut (Bronze)
2
-
-
(f) SS pump shaft as per existing
1
-
-
(g) GM impallar comlete with impolar key
1
-
-
(h) Gasket set manifold
1
-
-
Taking down from foundation base frame by disconnecting suction/delivery lines and coupling, opening including dismantling of centrifugal pump set of capacity 60 HP model DSM 100-36 and replacement of worn out spare parts as mentioned under respective item no-11 here in after and re-assembling, installation in same location including testing as directed. Make: Kirloskar
1
-
-
Supply only the following spare parts for centrifugal pump of 60 HP capacity model DSM 100-36 Make:- Kirloskar (a) Inter stage ring
1
-
-
(b Gland cap CI with nut bolt
2
-
-
(c) Wear ring CI
2
-
-
(d) Shaft Sleeve Bronze
2
-
-
(e) Shaft Sleeve Nut (Bronze)
2
-
-
(f) SS pump shaft as per existing
1
-
-
(g) GM impallar comlete with impallar key
2
-
-
(h) Gasket set manifold
1
-
-
Taking down from foundation base frame by disconnecting suction/delivery lines and coupling, opening including dismantling of centrifugal pump set of capacity 50 HP model DSM 100-36 and replacement of worn out spare parts as mentioned under respective item no-13 here in after and re-assembling, installation in same location including testing aa as directed. Make : Kirloskar
1
-
-
Supply only the following spare parts for centrifugal pump of 50 HP capacity model DSM 100-36 Make:- Kirloskar (a) Inter stage ring
1
-
-
(b) Gland cap CI with nut bolt
2
-
-
(c) Wear ring CI
2
-
-
(d) Shaft Sleeve Bronze
2
-
-
(e) Shaft Sleeve Nut (Bronze)
2
-
-
Taking down from foundation frame by disconnecting suction/delivery lines and coupling opening including dismantling of centrifugal pump set of capacity 40 HP Model No: UP 100-38 and replacement of worn out spare parts as mentioned under respective item No -15 here in after and re-assembling, installation in same location including testing aa as directed . Make : Kirloskar
3
-
-
Supply only the following spare parts for centrifugal pump of 40 HP capacity model UP 100-38 Make:- Kirloskar (a) Inter stage ring
6
-
-
(b) Gland Cap CI with nut bolt
12
-
-
(c) Wear ring
12
-
-
(d) Shaft sleeve Bronze
12
-
-
(e) Shaft sleeve nut bronze
12
-
-
(f) SS pump shaft as per existing
3
-
-
(g) GM impallar comlete with impolar key
2
-
-
(h) Gasket set manifold
3
-
-
Taking down from foundation frame by disconnecting suction/delivery lines and coupling opening including dismantling of centrifugal pump set of capacity 30 HP Model No: UP 80-38 and replacement of worn out spare parts as mentioned under respective item No-17 here in after and re-assembling, installation in same location including testing aa as directed. Make : Kirloskar
3
-
-
Supply only the following spare parts for centrifugal pump of 30 HP capacity model UP 80-38 Make:- Kirloskar (a) Inter stage ring
3
-
-
(b) Gland Cap CI with nut bolt
6
-
-
(c) Wear ring
6
-
-
(d) Shaft sleeve bronze
6
-
-
(e) Shaft sleeve nut ( Bronze)
6
-
-
(f) SS pump shaft as per existing
2
-
-
(g) GM impallar comlete with impolar key
1
-
-
(h) Gasket set manifold
3
-
-
Taking down from foundation frame by disconnecting suction/delivery lines and coupling opening including dismantling of centrifugal pump set of capacity 25 HP Model No: UP 80-38 and replacement of worn out spare parts as mentioned under respective item No-19 here in after and re-assembling, installation in same location including testing aa as directed. Make : Kirloskar
2
-
-
Supply only the following spare parts for centrifugal pump of 25 HP capacity model UP 80-38 Make:- Kirloskar (a) Inter stage ring
2
-
-
(b) Gland Cap CI with nut bolt
4
-
-
(c) Wear ring
4
-
-
(d) Shaft sleeve bronze
4
-
-
(e) Shaft sleeve nut ( Bronze)
4
-
-
Taking down from foundation frame by disconnecting suction/delivery lines and coupling opening & re-assembling of centrifugal pump set of capacity 20 HP Model No: UP 80-38 and replacement of worn out spare parts as mentioned under respective item No-21 here in after and re-assembling, installation in same location including testing as directed. Make : Kirloskar
4
-
-
Supply only the following spare parts for centrifugal pump of 20 HP capacity model UP 80-38 Make:- Kirloskar (a) Inter stage ring
4
-
-
(b) Gland Cap CI with nut bolt
8
-
-
(c) Wear ring
8
-
-
(d) Shaft sleeve Bronze
8
-
-
(e) Shaft sleeve nut ( Bronze)
8
-
-
(f) SS pump shaft as per existing
2
-
-
(g) GM impallar comlete with impolar key
1
-
-
(h) Gasket set manifold
4
-
-
Taking down from foundation frame by disconnecting suction/delivery lines and coupling opening including dismantling of centrifugal pump set of capacity 15 HP Model No: DSM-2E/UP 80-30 and replacement of worn out spare parts as mentioned under respective item No-23 here in after and re-assembling, installation in same location including testing aa as directed. Make : Kirloskar
1
-
-
Supply only the following spare parts for centrifugal pump of 15 HP capacity model DSM-2E/UP 80-30 Make:- Kirloskar (a) Inter stage ring
1
-
-
(b) Gland Cap CI with nut bolt
2
-
-
(c) Wear ring
2
-
-
(d) Shaft sleeve bronze
2
-
-
(e) Shaft sleeve nut ( Bronze)
2
-
-
(f) SS pump shaft as per existing
1
-
-
(g) GM impelar comlete with impolar key
1
-
-
(h) Gasket set manifold
1
-
-
Dismantling opening and reassembling after repair /replacement of U/S spare parts of mono block pumping set capacity 10 HP spare parts required shall be measured and paid for under respective item Sr No -25 of this schedule. Job includes disconnection from base foundation frame disconnecting electrically, reconnection, re-fixing in position transportation to work shop & back make of pump :- Kirlosker
2
-
-
Supply only the following spare parts for mono block pump of 10 HP capacity Make:- Kirloskar (a) Gland bush
2
-
-
(b) Gasket set manifold
2
-
-
Description all as per item No 24 but of cap 7.5 HP spare parts shall be measured and paid for under respective item Ser No 25
1
-
-
Supply only the following spare parts for monoblock pump of cap 7.5 HP , Make : Crompton Greaves (a) Gland Bush
1
-
-
(b) Gasket set manifold
1
-
-
All as per item No – 26 but capacity 5 HP spare parts required shall be measured and paid for under respective item Sr No -29
2
-
-
Supply only the following spare parts for mono block pump of 5 HP capacity Make:- Kirloskar (a) Gland bush
2
-
-
(b) Gasket set manifold
2
-
-
S&F in replacement following items suitable for 75 HP motor pumping set (a) Flexible tyre type coupling
4
-
-
(b) Ball bearing for motor(SKF/NBC)
2
-
-
(c) Ball bearing for pump ( SKF/NBC)
2
-
-
S&F in replacement following items suitable for 60 HP motor pumping set (a) Flexible tyre type coupling
2
-
-
(b) Ball bearing for motor(SKF/NBC)
2
-
-
(c) Ball bearing for pump ( SKF/NBC)
2
-
-
S&F in replacement following items suitable for 50 HP motor pumping set (a) Flexible tyre type coupling
2
-
-
(b) Ball bearing for motor(SKF/NBC)
2
-
-
(c) Ball bearing for pump ( SKF/NBC)
2
-
-
S&F in replacement following items suitable for 40HP motor pumping set (a) Flexible tyre type coupling
11
-
-
(b) Ball bearing for motor(SKF/NBC)
12
-
-
(c) Ball bearing for pump ( SKF/NBC)
18
-
-
S&F in replacement following items suitable for 30HP motor pumping set (a) Flexible tyre type coupling
3
-
-
(b) Ball bearing for motor(SKF/NBC)
4
-
-
(c) Ball bearing for pump ( SKF/NBC)
8
-
-
S&F in replacement following items suitable for 25HP motor pumping set (a) Flexible tyre type coupling
4
-
-
(b) Ball bearing for motor(SKF/NBC)
4
-
-
(c) Ball bearing for pump ( SKF/NBC)
4
-
-
S&F in replacement following items suitable for 20 HP pumping set (a) Flexible tyre type coupling
6
-
-
(b) Ball bearing for motor(SKF/NBC)
6
-
-
(c) Ball bearing for pump ( SKF/NBC)
10
-
-
S&F in replacement following items suitable for 15 HP motor pumping set (a) Flexible tyre type coupling
5
-
-
(b) Ball bearing for motor(SKF/NBC)
5
-
-
(c) Ball bearing for pump ( SKF/NBC)
5
-
-
S&F in replacement following items suitable for following cap of motor(a) Ball bearing for 10 HP (SKF/NBC)
4
-
-
(b) Ball bearing for 7.5 HP (SKF/NBC)
2
-
-
(c) Ball bearing for 5 HP motor(SKF/NBC)
2
-
-
(d) Ball bearing for 3 HP motor(SKF/NBC)
2
-
-
(e) Ball bearing for 2 HP motor(SKF/NBC)
2
-
-
(f) Ball bearing for 1.5 HP motor(SKF/NBC)
2
-
-
(g) Ball bearing for 1 HP motor(SKF/NBC)
10
-
-
(h) Ball bearing for 0.5 HP motor(SKF/NBC)
4
-
-
Replacement of U/S leather washers heavy duty with new leather washer heavy duty (ISI marked) suitable for foot valve of following size.
(a) 150 mm bore
25
-
-
(b) 100 mm bore
10
-
-
(c) 80 mm bore
10
-
-
Replacement of U/S foot valve with new foot valve of following size flanged/screwed type Make:- Kirlosker/ BIR (a) 150 mm bore
8
-
-
(b) 100 mm bore
8
-
-
( c) 80 mm bore
4
-
-
S&F in replacement PVC insulated sheathed 3 core submersible flat cable for submersible pumps copper conductor cable (stranded) 1100 volt grade of size 10 Sq mm Make:- Plaza/finolex/ Havells
200
-
-
Taking out UNSV selector switch and supply and fixing three way OFF three phase new selector switch for AC ammeter/Volt meter VN 63 Amp. Make:- Havells/HPL
15
-
-
supply and fix in replacement MCCB 100 Amp capacity triple pole breaking capacity 25 KA,FP, single frame, fixed thermal magnetic trip at 415 volts in existing panels of booster pump houses including making connections by using suitable size copper lugs/thimbles and crimping tool complete all as specified and directed by Engr in charge. Make: - Havells/ABB/Legrand
4
-
-
All as per item No 43 above but 125 Amp Capacity 25 KA
4
-
-
All as per item No 43 above but 400 Amp Capacity 36 KA
1
-
-
All as per item No 43 above but 250 Amp Capacity 36 KA
2
-
-
Taking down unsv & supply and fix MCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA Note : - Contractor will be deposit items ser No 44,45,46,& 47 in store and fixing as per direction by JE E/M & Engr -in- Charge.
4
-
-
S&F electronic type single phasing preventer in existing panel boards (max 600V min 380V) three phase 415 volts variation voltage 4% tripping time 2-5 sec max type VSP-1 complete all as directed by Engr in charge. Make:- L&T/Minilac/Siemens.
8
-
-
Supply and fix in replacement star delta timer range 0 - 30 second. Make : C&S/L&T /Schiender
12
-
-
Dismantling of NRV of size 80/100/ 150/200mm carefully after disconnecting from delevery line of pumping set unscrewing the both side taking out seat with level and labour and material from replacement of leather washer cleaning inside seat space reassembling , reinstalling back complete as
13
-
-
Supply and fixing in replacement of NRV CI flanged ends ISI marked ( IS - 5312) size 200 mm bore with rubber or fibre board gasket including necessary nuts, bolts and washer complete all as specified and directed . Make : KIRLOSKAR/BIR/Upadhaya
2
-
-
All as per item No 51 above but of 150 mm bore
4
-
-
All as per item No 51 above but of 100 mm bore
4
-
-
All as per item No 51 above but of 80 mm bore
3
-
-
supply and fixing contactor of following cap of motor including disconnecting and taking down old existing unserviceable contactor (a) Contactor rating suitable for 40 Amp, 3 Pole with (01 No + 01 NC) for 20 HP motor. Make:- L&T/C&S/Siemens.
10
-
-
(b) Contactor rating suitable for 60 Amp,3 Pole with (01 No + 01 NC) for 30 HP motor
6
-
-
(c) Contactor rating suitable for 80 Amp,3 Pole with (01 No + 01 NC) for 40 HP motor
10
-
-
(d) Contactor rating suitable for 100 Amp,3 Pole with (01 No + 01 NC) for 50 HP motor
5
-
-
(e) Contactor rating suitable for 130 Amp,3 Pole with (01 No + 01 NC) for 60 HP motor
5
-
-
(f) Contactor rating suitable for 160 Amp, 3 Pole with (01 No + 01 NC) for 75 HP motor
6
-
-
Opening the gland cap from both side of centrifugal pump and taking out the rusted gland dori and refilling the new gland dori with grease both side of pump and refixing the gland cap in same position.
150
-
-
Taking up or down existing old/rusted/worn out cracked/broken 25mm bore GI pipe water tubing & connections.
125
-
-
Supply and fixing to walls, laid on roofs laid on floors, GI pipe of size 25mm bore ISI marked medium grade complete with fittings all as specified and directed by Engr in Charege.
125
-
-
M&L for opening the gland cap from both side of sluice vale and taking out the rusted gland dori and refilling the new gland dori with grease both side of sluice valve and refixing the gland cap in same position.
70
-
-
Taking out of UNSV analogue Amp meter and supply and fix new digital ebrit panel mounted AC ammeter (0-300A) of size 96 X 96 sqmm flush mounted case three phase, class 0.5 item code PAMEBRITA 32. Make:-AE/HPL
10
-
-
Taking down UNSV phase indicator lamp supply and fix new phase indicator lamp (red, yellow & blue)
10
-
-
Taking out of UNSV analogue volt meter and supply and fix new digital ebrit panel mounted AC volt meter (0-500A) of size 96 X 96 sqmm flush mounted case three phase, class 0.5 item code PAMEBRITA 32. Make:-AE/HPL Note : - Contractor will be deposit items ser No 65,66&67 to store and fixing as per direction by JE E/M & Engr -in- Charge.
20
-
-
Supply and fixing in replacement motor protection relay range 13-20 Amp
6
-
-
Supply and fixing in replacement motor protection relay range 22-30 Amp
8
-
-
Supply and fixing in replacement motor protection relay range 25-39 Amp
10
-
-
Supply and fixing in replacement motor protection relay range 38-60 Amp
6
-
-
S&F 20 mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 20 mm bore, complete, all as specified & directed. Make :- Leader/ Zoloto
20
-
-
S&F 25 mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 25 mm bore, complete, all as specified & directed. Make :- Leader/ Zoloto Note : - Contractor will be deposit items ser No 72&73 to store and fixing as per direction by JE E/M & Engr -in- Charge.
15
-
-
M&L for repair to unserviceable sluice valve of size 80mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete, all as specified and directed.
2
-
-
M&L for repair to unserviceable sluice valve of size 100mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete, all as specified and directed.
4
-
-
M&L for repair to unserviceable sluice valve of size 150mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete, all as specified and directed.
10
-
-
M&L for repair to unserviceable sluice valve of size 200mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete, all as specified and directed.
15
-
-
Supply & fixing in replacement cast iron body sluice valve heavy duty class ‘PN-1.6’ of 80 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and MS nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 80 mm bore, complete, all as specified & directed. Make Zoloto/Kirloskar/leader
2
-
-
Supply & fixing in replacement cast iron body sluice valve heavy duty class ‘PN-1.6’ of 100 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and MS nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 100 mm bore, complete, all as specified & directed. Make :- Zoloto/Kirloskar/leader
4
-
-
Supply & fixing in replacement cast iron body sluice valve heavy duty class ‘PN-1.6’ of 150 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and MS nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 150 mm bore, complete, all as specified & directed. Make :- Zoloto/Kirloskar/leader Note : - Contractor will be deposit items ser No 78,79&80 to store and fixing as per direction by JE E/M & Engr -in- Charge.
4
-
-
Supply & fixing in replacement cast iron body sluice valve heavy duty class ‘PN-1.6’ of 200 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and MS nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 200 mm bore, complete, all as specified & directed. Make Zoloto/Kirloskar/leader Note : - Contractor will be deposit items ser No 78,79&80 to store and fixing as per direction by JE E/M & Engr -in- Charge.
2
-
-
Supply & laying suction/delivery GI pipe line of size 150 mm bore ISI marked medium grade in short length both side flanged type with gasket joint nut bolts washers complete with fittings all as specified & directed by the Engineer-in-Charge. Make:- Jindal/Swastik/Tata
24
-
-
All as per item No 77 above but of 100 mm bore
30
-
-
S&F in replacement of metallic antivibration pads with rubber cushion for 75/60/50/40/30/25/20 HP motor pumping set including drilling hole at necessary places on foundation base frame. MAKE: Dunlop
18
-
-
Dismantling and taking down pump set from base foundation frame by disconnecting electrically and from coupling side taking out at side and demolition the old fondation and making foundation with PCC(1:2:4) type By using 20mm graded stone aggregate including grouting of base hole fast 08 Nos and metalic anti vibration pads with rubber cusion including watering leveling at same size after making of foundation installing of P/S and fixing same suction and delivery all as directed by Engr - in- Charge , suitable for following cap (a) 75/60 HP
2
-
-
(b) 40/30 HP
2
-
-
Supply and fix high speed pump size 65x80mm, 2900 rpm and discharge 29.8 m3/hrs, head 42 mtr, type of pump DB 65/20 suitable for 20 HP motor complete with fittings all as specified & directed by the Engineer-in-Charge. Make:- Kirloskar Note :- Cost will be deemed in quoted rate for fixing all complete accessories (coupling, rubber tyre coupling allingement on base frame ) in existing motor of capacity 25 HP
2
-
-
Taking down carefully existing unserviceable Copper/aluminum batten/surface conduit/concealed conduit point wiring (light, fan, bell/buzzer, socket or power) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, pendents, sockets, lamp holders, shades, fan regulators, light fittings, bells etc (including old MS sunken boxes) and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and as directed by the Engr-in-Charge.
68
-
-
Taking down of unserviceable DBs/switch fuses/changeover in sheet steel enclosure complete with MCBs/Fuse/grips any capacity and removing from site disturbed surface of wall, floor etc. Taking after disconnecting all cable complete all as specified and as directed by the Engr-in-Charge.
4
-
-
M&L Point wiring with stranded copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 1.5 Sq mm single core in and including PVC casing capping with all fittings such as tees, bends etc terminating in and including new sunken box covered with and including 3 mm thick bakelite laminated sheet top cover ‘Hylam’ for one fan or light or exhaust fan or bell/buzzer point controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed copper conductor cable, single core as earth wire to common earth & connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.
40
-
-
All as per item No 84 here-in-before but socket point on the same board with other switches complete as specifed as directed by Engineer - In - Charge
10
-
-
All as per item No 84 here-in-before but socket point on the independent board with other switches complete as specifed as directed by Engineer - In - Charge
10
-
-
All as per item No 84 here-in-before but cable of 2.5 Sq mm for 15 Amp switch socket outlet on independent board
8
-
-
S&F Switch piano flush type, Single pole 5 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge
60
-
-
M&L Ceiling rose PVC/poly carbonate insulated body three terminal ISI marked, complete all as specified and as directed by Engineer-in-Charge.
10
-
-
S&F Socket outlet flush type, 2 in one 1 pin, 5 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge.
20
-
-
S&F Switch piano flush type, Single pole 15 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge
8
-
-
S&F Socket outlet flush type, 3 pin, 15 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge.
8
-
-
S&F Lamp holder insulated body with back plate for conduit/casing capping fittings with 9 Watt LED bulb complete all as specified and as directed by Engineer-in-Charge.
10
-
-
S&F Fan regulator electronic type, 230 Volt, 150 Watt with 5 step of control including making holes in laminated bakelite sheet cover and connection complete all as specified and as directed by Engineer-in-Charge.
5
-
-
S&F Decorative ultra slim linear LED lightening fixture, energy efficent 18/20 Watt complete all as specified and directed by engineer-in-charge.Make Surya /Phillips/wipro/CG /Bajaj
20
-
-
Sheet metal enclosure for distribution boards, suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 8 ways double door , supplied and fixed in repair, including making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge.
2
-
-
Sheet metal enclosure for distribution boards, suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 4 ways double door , supplied and fixed in repair, including making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge.
2
-
-
MCB single pole, 240 volts of rating 6-32 Amps, breaking capacity of 10 KA complete all as specified and as directed by Engineer-in-Charge
16
-
-
MCB suitable for 6 to 32 Amps, 240 Volt AC supply single pole and neutral with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge.
4
-
-
Taking down old sub main wiring and providing new sub main wiring with 2 single core, multi-stranded PVC insulated cable unsheathed 1100 volts grade with copper conductor of size 2.5 sq mm drawn in and including PVC concealed including earth continuity conductor cable of size 1.5 sq mm PVC insulated unsheathed copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.
40
-
-
Supply and laying in replacement cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10.00 sq mm 3 core
150
-
-
Supplying, fixing, installation, commissioning & testing of self priming automatic pressure pumping set with numematic senser, pressure tank of suitable including all connecting accessories complete set 0.5 HP single phase 230 Volts AC Supply. Make : Kirloskar/CG/Bajaj.
1
-
-
Excavation in trenches in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 mtr in depth for route of cable and getting out complete all as specified and as directed by the Engr-in-charge.
22
-
-
Returning, filling in soft/loose soil including spreading, leveling watering and well ramming, in layers not exc 25 cm complete all as specified and as directed by the Engr-in-charge.
14
-
-
Removing of surplus soil to a distance not exc. 50 mtr and depositing where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and directed by Engr-in-charge.
8
-
-
Protection to cable with one layer of bricks laid flat butting to each other in such a way that the length of the bricks is at right angle to the central axis of the cable using old size sub-class 'B' bricks complete all as specified and directed by Engr-in-charge.
0.8
-
-
Local tibba dry sand cushioning for protection of cable complete all as specified and as directed by Engineer-in-charge. Note Local approved tibba dry sand after removal of vegetations, grass and other deleterious substances shall be used for sand cushioning.
8.1
-
-
M & L GI tubing light grade for protection of cables with pole/ in ground of size 40mm dia complete all as specified and as directed by Engineer-in-Charge.
12
-
-
Supply and fixing LED street light fitting 70 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. . Make:- Havells/CG/Philips
20
-
-
M&L for cleaning of water supply installation in surrounding area (entire in fencing ) including trimming, grsass cutting etc three times in a contract period complete all as specified and as directed by Engineer-in-Charge.
20
-
-
Meterial and labour for construction of brick masonary valve pit chamber of size 150 X 150 X 150 cm (internal dimension) using sub class 'B' bricks complete including necesary earth work etc. type 'B' including PCC 1:5:10 type E-2 using 20 mm graded stone aggregate in foundation, coping on top in PCC type B-2 using 20 mm graded stone aggregate, inner plaster 10 mm thick in cement mortar 1:4, MS sheet cover 1.6 mm thick with locking arrangement duly painted with two coats of synthetic enemal paint over a coat of primer red oxide including angle iron 35 X 35 X 4 mm frame complete all as specified and as directed
5
-
-
Supply and fix MS sheet cover 1.6 mm thick with locking arrangement duly painted with two coats of synthetic enemal paint over a coat of primer red oxide including angle iron 35 X 35 X 4 mm frame for masonary valve pit chamber of size 150 X 150 X 150 cm (internal dimension)complete all as specified and as directed.
5
-
-
Supply and fix MS sheet cover 1.6 mm thick with locking arrangement duly painted with two coats of synthetic enemal paint over a coat of primer red oxide including angle iron 25 X 25 X 4 mm frame for masonary valve pit chamber of size 90 cm X 90 cm (internal dimension) complete all as specified and as directed.
5
-
-
Taking down broken /rusted iron base frame and Supply and fixing new iron base frame for centrifugal pump set of capacity 40/30/20 HP as per existing size with two coats of black paint over a coat of red oxide zinc chromate primer complete all as specified.
5
-
-
Plain cement concrete (1:2:4) type C-2 using 20 mm graded stone aggregates as in foundation of poles above /surrounding area in OHT including finishing to exposed concrete surfaces even and fair and provision of form work for rough finished surfaces complete all as specified and as directed by Engineer-in-Charge.
3.5
-
-
Taking down unsv iron chequired sheet /grill/chanel frame & supply and fix New iron chequired sheet of thickness not less than 6 mm/ grill/chanel frame with angle iron as per existing size including welding and two coat of red oxide paint and one coat of black enamel paint complete all as directed by Engr-in -Charge
5.5
-
-
Supply & fix multistranded stranded copper conductor of size 16 Sqmm single core including copper thimble all as directed by Engr in Charge, Make Havells/poly cab/Finolex
100
-
-
Painting with two coat of synthetic enamel paint ( Blue Sky colour) on Iron Board/ wall surface and writing white enamel paint with the details of
(a) MES
(b) BOOSTER PUMP HOUSE NO (c ) GE (N) Bikaner, Type / hight of the words complete all as directed by Engr - in Charge
Note:- writting will be professional skilled person.
20
-
-
Supply and fix fully automatic star delts starter suitable for 30 HP motor with all type protection device all as specified and directed by Engr-in Charge. Make :- ABB/L&T Cat pt No SS94364
2
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements