Military Engineer Services Tender

Re-laying only of existing Jodhpur Stone Patti cable cover in Trenches for Under Ground Cable Protection (Serviceable Materials obtained from Item No. 6.00 here-in-before) complete all as specified and directed by Engineer-in-charge.

M&L for sand cushioning to underground PVC/XLPE cable and punning to provide required cover complete all as specified and directed by Engineer-in-charge. Note :- For the purpose of payment only punned thickness will be measure.

Taking down/out unserviceable LT UG Cable of any descriptions, laid in trenches and/or fixing with Walls/Poles including stone patti complete all as specified and directed by Engineer-in-charge.

Supply, lay, test and commissioning of LTUG, XLPE insulated, heavy duty, 1100V grade of size 95 Sqmm 3½ core electric cable with aluminum conductor, served with an inner sheathing of PVC tape armored with galvanized steel wire or tape and overall PVC sheathed, laid in trenches or passing through pipe, making all connections with and including provision of necessary glands, lugs, bushing etc as required complete all as specified and directed by Engineer-in-charge. Note : Earthwork excavation sand cushioning ,Jodhpur Stone patti, GI protection pipe shall be measured and paid separately in their respective items

All as per Item No 7.00 here-in-before but size 70 sq mm. 3½ core

All as per Item No 7.00 here-in-before but 25 sq mm. 4core

All as per Item No 7.00 here-in-before but 16 sq mm. 4 core

All as per Item No 7.00 here-in-before but 10 sq mm 2 core

All as per Item No 7.00 here-in-before but 16 sq mm. 2 core

Relaying /Refixing only existing XLPE insulated , Armoured , Electric Power UG Cable (Heavy Duty) , 1100 Volt Grade , any Nominal Cross sectional area complete all as specified and directed by Engineer-in-charge.

S&F Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts and screws as specified type 410 SP-31 (9 metres long) and including pole number marking with stencile cutting and one coat of red oxide primer and two coat of aluminium paint over a pole including dismantlaing/taking out existing PCC/Steel tubular pole and making surface good complete all as specified and directed by Engr -in-Charge.

M&L for cement concrete (1:4:8) type D-2 using 40mm grade stone aggregate in foundation of PCC pole/struts as specified including necessary form work finishing even and smoth with out using extra cement complete all as speficied and directed by Engineer-in-Charge.

M & L for cement concrete (1:3:6) type C-2 using 40mm grade stone aggregate for foundation of stay assembly struts or pole or around the pole structure etc complete all as speficied and directed by Engineer-in-Charge. Note: PCC (1:3:6) work in around the pole structure min 100mm thickness after cleaning the surface area.

M&L for cement concrete (1:2:4) type B-1 using 20mm grade stone aggregate for coping/encasing around poles including necessary form work finishing even and smoth with out using extra cement complete all as speficied and directed by Engineer-in-Charge.

Taking down Unservicable street light/ flood light/ solar light/post top lantern fitting of any size /type/capacity any Watt from height of pole/walls/ for repair work and re-fixing back after repair work including checking, inspecting, testing and commissioning complete all as speficied and directed by Engineer-in-Charge. Note :- (a) Spares like LED Driver,surge protector ,service wire etc. shall be measured and paid as separetely under relavant items of schedule'A' (b) Necessary tools like mobile ladder & other T&P required etc shall be arranged by the contractor without any extra cost. (c) The rate quoted deemed to be inclusive for minor repair parts like nuts, bolts, cirle clips , clamps etc required if any at site.

Supply and fix of electronic driver for LED light fitting, LED out put power 30 watt, input voltage range : 170 - 300 volt AC , out put voltage DC as per make/ model range: 24 volt to 110 volt, complete all as speficied and directed by Engineer-in-Charge. Note :- make as per site requirement as approved by GE.

All as per Item No. 19.00 here-in-before but capacity 45 watt

All as per Item No. 19.00 here-in-before but capacity 60 watt

All as per Item No. 19.00 here-in-before but capacity 70 watt

All as per Item No. 19.00 here-in-before but capacity 90 watt

S&F Surge Protector 10KV for street light fitting, Normal voltage input range : 170- 300 volt complete all as speficied and directed by Engineer-in-Charge.

Taking down of existing Led Street Light and S&F led street light of capacity 60 Watt, including making electrical connection to the fitting with suitable size of wire,Having Pressure Die Cast Aluminium Housing, Ip-66 Having Efficiency Of ≥ 110 Lumens/Watt with toughend glass , Operating Voltage – 120 – 270 Volts, P.F ≥ 0.95, T.H.D 10 % , Both Fixture And Drivre Must Have Separate Bis Marked Registration With Clearly Mentioned On Fixture & As Well As On Driver Also. The Fitting Must Be Suitable For 35 To 50 Mm O.D Mounting Pipe And Suitable For Mounting On Wall / Pole With Necessary Mounting Arrangements ) Including Connecting Up With Three Core Twisted Flexible Copper Conductor Cable With Suitable Size, Mounting Pipe/Bracket , Nut, Bolts and accessories complete all as speficied and directed by Engineer-in-Charge. Make :- Crompton cat part No. TRP-409-60-57-SL-GL-NSG or Equivalent make and model as approved by GE and the Manufacturer of the Led Fitting Shall Have Inhouse Nabl Accrediated Lab & Contractor Shall Furnish Same Along With Lm-79,Lm-80, Test Report Etc. all report shall be approved by GE.

Taking down of Lithium based energy efficient Integrated solar street light and S&F existing Lithium based energy efficient Integrated solar street light of 20 watt in single body with FRP/Aluiminum duly polyurenthane coating (camouflage colour)encases with monocrystalline solar PV panel of 30/35Wp, Lithium battery 11.1/12.8 Volt, 24 Ah with inbuit BMS, IP 65/66, High brightness W-LED (120-180 Im/Watt) lamp with aluminium reflector for better lighting distribution, CRI 70, colour temperature 5700 K-6500 K, Microcontroller based charge controller cum driver, automatic dimming function with PIR motion sensor,Dusk to dawn operation weight not more than 10-12 KG with adjustable MS Clamp suitable for existing pole/wall mounting etc complete all as specified and directed by Engineer-in-charge. Note : Short Circuit, overload, reverse polarity and battery protections to be provided. OEM should provide vital parameters test report from NABL accredited lab and should be of made in India with CE & TOHS complaint.

S&F PVC insulated, sheathed weather proof, copper conductor of size 1.5 sqmm, 3 core including taking down of existing complete all as specified and directed by Engineer-in-charge.

S&F PVC insulated, sheathed weather proof, aluminium conductor of size 6 sqmm, 2 core including taking down of existing complete all as specified and directed by Engineer-in-charge.

M&L for PVC conduit 20 mm, heavy duty rigid non metallic including of all tee, bends, elbows, MS clamps suiable for steel tubular /pcc pole etc including taking down of existing complete all as specified and directed by Engineer-in-charge.

S&F 40 mm bore GI tubing light grade in trenches or on pole for cable protection including taking down of existing complete all as specified and directed by Engineer-in-charge.

S&F 80 mm bore GI tubing medium grade in trenches or on pole for cable protection including taking down of existing complete all as specified and directed by Engineer-in-charge.

S&F pole mounted junction box of outer size 300x200x120mm made out of FRP body (hot mulded type) with IP-66 protection and locking with screws alongwith 6-32 Amp rating MCB SP-01 No, up to 50 Amp rated 4 pole connector suitable to insert the cable size up to 25 sqmm x 4 core -02 No and din rail suitable for mounting the MCB/Connector etc complete in side box and duly fixed with 25x3mm FI clamps with nut bolts of suitable size on steel tubular pole/PCC/RCC pole including cable glands, aluminum lugs/thimbles for incoming and out going cables and including taking down of existing of pole mounted junction box complete all as specified and directed by Engineer-in-charge.

S&F galvanised iron bracket of 'medium grade' pipe 40 mm bore, length 1.20m, bend to required shape with 2 Set clamps made of 40x6mm FI and suitable size of bolts, nuts & washers, etc duly painted with two coats of aluminium paint over a coat of red oxide primer complete for fixing street light fittings including taking down of existing galvanised iron bracket complete all as specified and directed by Engineer-in-charge.

S&F feeder pillar box out door tpye not less than 0.60 M x0.60 M x0.60 M made out of 3.15 mm thick CRCA sheet powder coated dust & vernin proof supported on angle iron frame 40x40x5 MM , with Incoming MCCB 4 pole, 200 Amp 415 Volts , 36 kA rupturing capacity ,with adjustable setting 80% to 100 % thermal magnetic release -01 No (Ics =100%Icu) and outgoing MCCB 160 Amp -01 nos ,and MCB TPN 63 AMP,4 pole -01 Nos luminium bus bar 04 Nos vertivally fitted Aluminium strips rated capacity 300 Amp for netural supported on porcelain insulators including painting with two coats red oxide primer and pcc foundation including taking down of existing feeder pillar box complete all as specified and directed by Engineer-in-charge. Note:- Company test report of bus bar will be required

S&F feeder pillar box out door tpye not less than 0.60 M x0.60 M x0.60 M made out of 3.15 mm thick CRCA sheet powder coated dust & vernin proof supported on angle iron frame 40x40x5 MM , with Incoming MCCB 4 pole ,160 Amp 415 Volts , 36 kA rupturing capacity ,with adjustable setting 80% to 100 % thermal magnetic release -01 No (Ics =100%Icu) and outgoing MCCB 100Amp -01 nos ,and MCB TPN 63 AMP,4 pole -01 Nos luminium bus bar 04 Nos vertivally fitted Aluminium strips rated capacity 300 Amp for netural supported on porcelain insulators including painting with two coats red oxide primer and pcc foundation including taking down of existing feeder pillar box complete all as specified and directed by Engineer-in-charge. Note:- Company test report of bus bar will be required

M&L for bore earthing not less than 250 mm dia 16 feet deep filled with black soil up to 7 feet from bottom complete with galvanized iron pipe 40 mm bore medium grade 3 meter long tapers at bottom & provided 12 mm holes (staggered) at 75 mm centre to centre up to 2.5 meter of length from bottom , burried directly in ground filled with 45 cm alternate layer of chemical magnisium sulphate & salt up to ground levl connected to galvanized iron strip 32 x 6 mm as earthing lead by means of bolt and nut, check nuts and washer of galvanized iron or steel including brazing work and 40mm dia light grade pipe for earth lead protection and testing on completion and including taking down of existing bore earthing complete all as specified and directed by Engineer-in-charge.

S&F in repair MCB, single pole, 16-32 Amp, 240 Volts, 'C' Curve 10KA complete all as specified and directed by Engineer-in-charge.

S&F in repair MCB, SPN, 32 Amp, 240 Volts, 'C' Curve 10KA complete all as specified and directed by Engineer-in-charge.

S&F in repair 415V 10KA 'B' curve miniature circuit breaker (MCB) of capacity in the DB/ Panel box/ feeder piller box complete with connection testing and commissioning MCB, TPN 40 Amp, complete all as specified and directed by Engineer-in-charge.

S&F in repair MCCB 415V, 3 phase 50 HZ 4 pole 250 Amps breaking capacity 16 KA (Ics = 100% Icu) with connection link on LT panel /fedder piller complete all as specified and directed by Engineer-in-charge.

M&L for straight through (Heat Shrinkable) cable jointing kit for 1100 Volt grade cable complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 10/95 SQmm including dismantling the old burnt cable joint termination complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old painted surface of LT Steel tubular pole of any length by removing all dirt, dust,etc and painting complete surface up to pole top including connected accessories with dual coat of apex exterior, synthetic enamel paint over a coat of primer of approved colour of black and white strip 30 cm height (Total 5 Nos) & rest of the height of the pole is in silver colour aluminium paint, including bracing /clamps /brackets /nut and bolts support on poles and writing of identification Nos with proper stencil cut etc as per directions by Engr-in-Charge and complete all as specified and directed by Engineer-in-charge.

S&F Nature switch (using infrared sensor technology ) based automatic street light control panel. The panel should be enough to take three phase load of 25 kw.Nature switch operation should be based on natural light luxes. required illuminance level switching ON is =60 and for Switching OFF =10 lux. the senser should be have a part night operation facility of min 4HRS to max 12 hrs . the senser along with suitable 3 phase load of 25 KW with 3 nos contractor ,3 nos Incoming MCBs of 63 Amps and outgoing MCBs of 63 Amp and circuit wire copper of min 16 Sqmm and should be enclosed in a pole /wall mountig Rust proof ,Electric shock proof, Termite proof and FR grade thermoplastic polycarbonate enclouser (with hinged lid) conforming to IP66 protection.The circuit should also have provision gor Manual or Auto operation including taking down Nature switch complete all as specified and directed by Engr-in-Charge.

M&L for Cutting the road / hard standings and excavating in trenches not exceding 0.40 mtr wide and not exc 0.80 mtr deep across the road for laying cable including making good the excavated portion by means of PCC 1:2:4, type B1 using 20mm graded stone aggregate complete and matching with the surroundings complete all as specified and directed by Engr-in-Charge.

S&F Retro Reflective Tape 3 inch width red and yellow colour sutiable for steel tubular pole and RCC Pole including taking down of Retro Reflective complete all as specified and directed by Engr-in-Charge.

Note for all items:- (a) Contractor has to arrange his own vehicles along with mounted hydraulic ladder/articulated & telescopic boom lift arrangement for attending the complaint throughout jaisalmer cantt area. (b) Contractor shall depute minimum 2 staff daily to attend and rectify the complaint. if not, Contractor shall have to bear a penalty of Rs 50.00 per complaint or maximum of Rs 500 per day on this account (c) Complaints has to attend and rectify the complaint/defect irrespective of no of trips/Complaints as alloted by Eng-in-Charge.(d) Complaint should be attend in Night also (d) Contractor has to arrange telescopic boom lift for maintenance at height of 15m at his own cost. No extra payment will be paid by department.