Northern Railway Tender
... More
If you want to inquire about any e-tender the Punjab government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder you will find every eprocurement Punjab tender on BidAssist.There is no need to enter all the details on the website of etender.up.nic.in as BidAssist helps you find the specific Punjab etender you're looking for. Read further to learn how to search and bid for etender Punjab.
Technical
Technical
Financial
Additional Eligibility
Class Of Bidder
... View More
The eligible classes required by a bidder to participate or bid in the tender are 'Class-I local supplier' and 'Class-II local supplier'.
Technical Capacity
... View More
The required prior work experience for the bidder includes completing similar nature of work within the last 7 years. The values and percentages of similar works completed are as follows:
- For component B: 30%/40%/60% of Rs. 20 Cr
- For component C: 35% of Rs. 5 Cr
- For a combined component: the combined advertised value of all such components, for example, 30%/40%/60% of Rs. 25 Cr = 20 Cr + 5 Cr
- Component with value Rs. 23 Cr: 30/40/60% of Rs. 23 Cr in 3/2/1 no(s) of works of similar nature completed in 7 years
- Component with value Rs. 15 Cr: 30/40/60% of Rs. 15 Cr in 3/2/1 no(s) of works of similar nature completed in 7 years
- Component with value Rs. 5 Cr: 35% of Rs. 5 Cr single work of similar nature completed in the last 5 years
- Component with value Rs. 4 Cr: 35% of Rs. 4 Cr single work of similar nature completed in the last 5 years
- Component with value Rs. 3 Cr: work experience as per specified criteria, which can be executed by the tenderer himself or through a sub-contractor. The bidder must have successfully completed or substantially completed any of the following works during the last 07 years: - Three similar works each costing not less than 30% of the advertised value of the tender, - Two similar works each costing not less than 40% of the advertised value of the tender, - One similar work costing not less than 60% of the advertised value of the tender. In case of composite works, the tenderer must have completed similar works for each component, with values of 30%, 40%, or 60% of the advertised value of each component. The cost of each component should be more than 2 crore. For subcontracting, the subcontractor shall have successfully completed at least one work similar to the work proposed for subcontract in the last 5 years, costing not less than 35% of the value of the work to be subletted. However, for subletting of work costing up to Rs 50 lakh, no previous work experience is required. A substantially completed work means an ongoing work in which payment equal to or more than 90% of the present contract value has been made to the contractor. The percentage of similar works completed is 90% for substantially completed work. The amount for similar works completed is the total gross amount already paid, including the PVC amount (if paid).
Costs
EMD
₹ 3,42,800Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
287-SIG-C-TKJ-74-25-DYCSTE-C-TKJ-S AND T/NORTHERN RLYTender No
287-SIG-C-TKJ-74-25Tender Authority
Northern Railway ViewPurchaser Address
-Website
http://ireps.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
... More
Supply of 48VDC (2VDC, 200AH x 24) VRLA maintenance free battery as per RDSO spec no.IRS-S-93/96(A) or latest. Inspection : RDSO
1
67681
67681.85
... More
Supply and fixing of Spigot for point machines. (Job = Per Pt.M/c) . (Inspection : Site Engineer)
6
252
1517.76
... More
Supply of Plastic Coupler- Slip fit/ Push fit type for HDPE duct outer dia 40mm and inner dia 33mm as per TEC Gr No. G/CDS-08/02 Nov /2004 with latest amendment (Inspection. Consignee)
2
86
172.94
... More
Supply, installation, commissioning of analogue type Linear Heat Sensing (LHS) cable 101 which is self restorable after the fire event as long as its temperature does not exceed specified resettable temperature limit of 120 degree celsius it shall have an activation temperture of 70 degree celsius as per RDSO/SPN/217/2016, Ver 1.0 or latest. (Inspection : RDSO for supply portion and Installation by Site Engineer)
250
1778
444535
... More
"Supply, Installation, testing and commissioning of Electrically Operated lifting barrier assembly as per RDSO Spec no. RDSO/SPN/208/2012 (version 2.0) or latest consisting of 2 nos. of electrically operated lifting barriers, 2 pedestals, 8 band circuit controller with limit switches of Siemens, hand cranks, 2 electric motors, 110V AC, without centrifugal switch, 2 GI Boom in 4 sections of 8 feet each with 2 retroreflective stop boards, boom light boxes, MS counter weight, 2 nos. of boom support for resting boom etc. The item also consists of following items: a. Supply of motorized boom locking /unlocking assembly with electrical coil complete (1 no. each) b) Supply of level crossing gate control panel floor mounting type with swithches and buttons sheet metal fabricated, (1 No) c) Supply 74 of push button for operating the gate with 2 NO/NC contact, green colour-close & Amber-open, Siemens or Kaypee or similar make (1 no. ) d).Supply of solid state electronic flasher 24V DC operated (1 no. each). e) Supply of dual tone warning bell with 20W horn & 15W amplifier (2 no. each). Installation & Commissioning of LC gates includes excavation & casting of foundation of 1:3:6 for pedestal and boom rest with contractor's own material including cement, anchor bolts, erection of lifting barriers assembly right hand/left hand boom complete on the pedestal, fixing of boom support for lifting barrier boom, installation of boom locking devices & control panel, flasher, warning bell with associated warning. This includes power supply connections, wiring and other outdoor Works etc. All materials for installation & wiring shall be supplied by the contractor. Installation to be done by OEM or its authorised dealer. A certificate to this effect to be submitted by contractor. Inspection by RDSO (except item no. (c,d&e) by consignee)"
1
641729
641729.03
... More
Supply, installation, commissioning of Linear Heat Sensing interface module as per RDSO/SPN/217/2021, Ver 3.0 or latest. (Inspection : RDSO for supply portion and Installation by Site Engineer)
1
148032
148032.37
... More
Supply of End plug for HDPE duct outer dia 40mm and inner dia 33mm as per TEC Gr No. G/CDS-08/02 Nov /2004 with latest amendment. (Inspection : Consignee)
2
33
67.08
... More
Supply, installation, wiring and commissioning of Secured L.C. Gate electronic 1+6 nos 78 Telephone System with inbuilt voice recorder in 1+6 configuration with central supply as per . Specification No. RDSO/SPN/TC/51/2011 Rev.3.0 or latestSupply of L.C. Gate Telephone System with inbuilt voice recorder in 1+6 configuration with central supply as per . Specification No. RDSO/SPN/TC/51/2011 Rev.3.0 or latest. Inspection : RDSO
1
89410
89410.96
... More
Supply, installation, commissioning of UL listed glass break manual call point as per RDSO/SPN/217/2021 Ver. 3.0 or latest. (Inspection : RDSO for supply portion and Installation by Site Engineer)
2
5775
11550.24
... More
Supply of Colour light signal post 3.6mtr and ladder 3.5Mtr and bases as per tech. spec. IRS-S-6-81, Rev-3 or latest . (Inspection : RITES)
6
19054
114324.66
... More
Supply, installation, commissioning of audio visual alarm unit as per RDSO/SPN/217/2021, Ver 3.0 or latest. (Inspection : RDSO for supply portion and Installation by Site Engineer)
2
11421
22842.48
... More
Supply, fixing and wiring of PPTC Fuses 2/6A make tyco/Raychem/Bourn/Fuzetech/Little Fuse or similar. (Inspection : Consignee for supply portion and Installation by Site Engineer)
200
8
1702
... More
Casting, concreting and curing of foundation for main signal of size 51 (1041mmx1041mm)at bottom and (711mmx711mm) at top and 1750mm deep as per approved Drg. no. NR/SandT/CON/2.1/97 all material such as anchor bolts, cement, coarse sand aggregate to be supplied by contractor. (Inspection : Site Engineer)
15
12113
181709.4
... More
Fabrication and installation of illuminated indication Diagram Board of salwood with white sunmica top having aluminum angle of size 1"x1"x1/8" on all 4 sides duly painted for station 76 working rule diagram in Level Crossing. Board of size 1.2m x 0.6m x 20 mm thick shall be provided. The indications for signal, slot etc shall be provided near the signal painted on the yard diagram. It includes of all materials like LED, Holders ,wires etc will be supplied by the contractor. Inspection Consginee
1
6539
6539.25
... More
Supply & installation of SMPS based FR-FC charger for system rating 25Amp 48VDC (N+1) configuration i.e. using 2 module of 25Amp with automatic switching between the modules as per RDSO/SPN/TL/23/99 or latest. Inspection : RDSO
1
112955
112955.42
... More
Supply of Hydrometer of reputed make for measuring specific gravity of battery, graded acid with mounting stand in Battery Room/ location boxes. (Inspection : Consignee)
2
290
581.42
... More
" Installation, erection, wiring of 3/4 aspect color light signal. Fixing of CLS surface base, bolting on the foundation. Erection of CLS post with signal unit on the top or on an off-set bracket and fitting ladder and guard to the post at the top. Concreting ladder base and embedded into the ground with supporting bracket in the middle, blanking of the ladder for a distance of 1 feet between the height 6' 9" and 7' 9" from the rail level by MS angle and MS sheet 6mm thick wherever required. This includes provision of wooden (SAL) cross arm 1 mtr x 1 mtr for CLS unit prior to the 58 commissioning, fixing of LED aspect, current regulator and hoods of CLS unit, terminating cables, wiring the CLS unit and focusing the signal. Elevation and distance of foundation from track shall be in accordance with schedule of dimension for Indian Railways and as per NR practice. All items for the above Works except Signal unit, LED signal, Signal post, Base and Ladder shall be supplied by the contractor including but not limited to the following: i) "U" bolt for offset brackets, ii) Wooden cross arm 1 mtr. x 1 mtr., iii) MS angle and MS sheet for blanking of ladder,iv) Supply and fixing of signal number plate (retro reflective) with complete fittings as per standerd railway practice. v) Wire mesh guard, lock for unit if required, nuts, bolts etc (Inspection : Site Engineer)"
6
4703
28218.72
... More
Supply of Insulation for 'P' bracket for point fitting IRS type complete consisting of Insulation plate - 01 No. Ferrule - 02 Nos. Washers - 04Nos. (Material Nylon 66). (Inspection : Consignee)
12
776
9313.44
... More
Supply and laying of RCC pipe including split pipe where required 150mm inner dia, 2 28 meter long with collers (to specification No.IS-458/2003 or latest) in the trench across the track/road and L-xing gates etc.(Length of half pipes will be counted as combined length of top and bottom). (Inspection : Site Engineer)
50
503
25181.5
... More
Supply, laying and fixing of HDPE double Wall Corrugated (DWC) Duct as per as per RDSO Specification No. RDSO/SPN/204/2011 Ver. 1.1 With Amndt-1 (outer dia 120mm in 6m st. length 29 with one coupler for every 6m length). All the materials cement, sand etc. are to be supplied by the contractor. This include brick work and other arrangements required to secure the pipe as per specifications, drawings and stipulations of tender documents and as per approved cable route plan including road crossing/platform/track crossing and for bridges and culverts etc. (Inspection : Consignee for supply portion and Installation by Site Engineer)
200
494
98996
... More
Preparation of App. Case single involving wiring of relays. Preparation and fixing of bakelite hylum sheet 910x800x6mm and backelite shelf 900x450x10mm duly fixed by angle iron piece of different size inside all the app. Cases. Hylum board shall be fixed on an angle iron frame of 25mmx25mmx3mm. Angle iron frame will be fixed in location boxes secured by nuts and bolts.This includes fixing of fuses, ARA terminal, Q series relays and other type relays on square bars fixing and jamming of cables with 2 inch thick salwood plank provided at the bottom. This will include opening, 41 pasting and jamming armour of each cable in the hole drilled separately for each cable through the salwood plank and all cable entry points on location boxes, location huts, JBs relay room/battery room to be closed with suitable masonry Works covered with sand and plastering.Wiring description for terminal drawing of circuits, inside app. Case. Painting from out side as well inside with red oxide and aluminum paint is covered separately. Size of lettering will be 100mm or as per instructions of Engineer at site. All materials including Backelite shelf, hylum board, salwood plank, angle iron square bar, wire and wiring material catenary wires , nuts and bolts and other items shall be supplied by the contractor. Relays, ARA terminals, fuse with base only shall be supplied by the Railways. (Inspection : Site Engineer)
30
6747
202433.1
... More
Fabrication, supply and fixing of scaffolding /cable carrier made of angle ironof Size 8 35mmX35mmX5mm and flat of size 25mmX3mm as per instructions of engineer at site.The space between two flats will be 25cm or less as per site requirements allthe fixing materials i.e nut, bolt washer, insulators, cement concrete etc will be supplied by the contractyor . This includes insulating flat strips, cleaning priming by Red oxide, painting by ISI mark paint. (Inspection : Site Engineer)
100
523
52375
... More
Fabrication, supply and fixing of cable marker as per RDSO drg no. SDO/Cable Laying /020, dated 31.10.11. The marker shall be fixed at various places of cable route as per instruction of Engg. At site. (Inspection: Site Engineer)
250
1452
363197.5
... More
Preparation of App. Case single to be used as battery box.(not requiring shelf and hylum of size 910x150x6mm only is reqd.). Preparation and fixing of bakelite hylum sheet 910x150x6mm. Hylum board shall be fixed on an angle iron frame of 25mmx25mmx3mm. Angle iron frame will be fixed in location boxes secured by nuts and bolt sthis includes fixing of fuses, ARA terminal and jamming of cables with 2 inch thick salwood plank provided at the bottom. This will 43 include opening, pasting and jamming armour of each cable in the hole drilled separately for each cable through the salwood plank and all cable entry points on location boxes, location huts, JBs relay room/battery room to be closed with suitable masonry Works covered with sand and plastering.Wiring description for terminal drawing of circuits, inside app. Case. Painting from out side as well inside with red oxide and aluminum paint is covered separately. Size of lettering will be 100mm or as per instructions of Engineer at site. All materials including hylum board, salwood plank, wire and wiring material , catenary wires, nuts and bolts and other items shall be supplied by the contractor. ARA terminals only shall be supplied by the Railways. (Inspection : Site Engineer)
10
3343
33431.4
... More
Fabrication and Supply of complete set of point rodding for point machines of IRS type 68 or its equivalent type as per . drg. No. SA 8800-01 (Adv) or latest along with 'P' brackets and 'L' bracket required coal Bengal for smithy work, all type of nuts and bolts and ,washers and spring washers ,Lugs as reqd also to be supplied by contractor with each set. (Inspection : Consignee)
6
9669
58018.86
... More
Casting , concrete, curing of foundation for (installation and commissioning) sliding boom gate, fixing of sliding boom & Lock as per Railway engineer at site. All materials such as anchor bolts, cement, & aggregate to be supplied by the contractor. Inspection Site Engineer
1
47753
47753.85
... More
Supply of Switch board PVC Telecom cable as per IRS specificaion no. IRS TC-24/91 Make delton or similar 10 pair/0.6mm. (Inspection : Consignee)
200
88
17638
... More
Supply of ARA Terminal Block 25MM center M6 terminal made of PBT as per IRS spec. No.IRS-S-75/2006 (Rev.2) and IRS drawing No. SA-23741A(Alt.4), SA23745(Alt.5) ,SA-23746 and SA- 23756(Alt.3) . (Inspection : RDSO)
8000
77
618640
... More
Supply ,Wiring and Installation of Managed Expandable rack type STM-1 long haul ADM S1.1 equipped with 21E-1 as per technical spec. no.TEC GR No.GR/SDH-04/02 March 02 with latest 142 amendment 1,2,3 and 4 or latest with 2xSTM agreegate interface 21 EIs and 4 Nos of 10/100 base T Ethernet port order wire, power supply unit, sub racks. Installation material and accessories, manual etc. The equipment should be fully wired for its ultimate capacity and provide redundancy for power- supply and synchronization and other details. Inspection : RDSO. Note Item must be compatible with adjacent station.
1
223092
223092.73
... More
"Prep. of Station Working Rule Diagram, Cable route plan, Cable core chart, Track jumpering plan, Power supply arrangement plan based on station specific load calculation for indoor and out door , Circuit termination chart, Cable termination chart in relay room ,relay hut (if applicable) and location boxes, Location wiring plan, Cable insulation chart and register, Track circuit history card, 25 Fuse analysis plan , Equipment disposition plan, Track circuit plan, Terminal and Contact analysis chart , Outdoor circuits,pull sheets,goomtie plans,diagrams. temp. plans required for execution of PNI/NI and other outdoor diagram and obtaining approval of the Engineer as per following :- (i) Supply of 6 copies of completion set of superior quality paper, laminated, properly bound in steel clip jaw file with cushioned cover.(ii) Software back up of complete set in the form of Pen drive (32 GB). (iii) One complete set of tracings.(iv) Design through CAD(v) Drawings in A3 and plans in bigger size (six sets) in folders. (Inspection : SSE/C/DandD)"
1
43714
43714.82
... More
Supply of 1-way route indicator junction type as per drg. No. SA-23401 (adv.) or latest complete with hoods and offset bracket 5 1/2" as per . specn.no.IRS-S-66/84 (Amd-1) or latest as per latest drawing. (Inspection : RITES)
2
26312
52624.1
... More
Supply of Insulation for 'L' type bracket for point fitting IRS type complete consisting of Insulation plate - 01 No. Ferrule - 02 Nos. Washers - 04Nos. (Material Nylon 66). (Inspection : Consignee)
6
307
1846.2
... More
Installation wiring and commissioning of 4 - wire way station eqpt.Item required for installation such as wires, wiring materials, connectors, battery rack runway, hardware etc. to be supplied by contractor. (Job = Per way stn. eqpt.). (Inspection : Site Engineer)
4
4084
16337
... More
"Supply, Installtion and Commissioning of maintenance free earth suitable kit as per RDSO Specification no. RDSO/SPN/197/2008 and Drg No. SDO/RDSO./EandB/001 dated:- 19.09.2008 and Drg No. RDSO/SDO/RDSO./EandB/002 dated:- 19.09.2008. Earthing kit consisting of earthing electrode of 17mm dia as 3m long -01 no 2 MEEB (300mmx25mmx6mm) -o1 no. 3. SEEB (150mmx25mmx6mm) -01 no 4. Earth enhancing compound - 30 kg (minimum). This includes:- Provisiion of earth connection from MEEB to SandT equipment i.e. cable sheath, apparatus case, BPAC, Axle counter, IPS, Data Logger etc. with PVC earth wire of size 10/16/25 sq.mm through copper lugs of 93 suitable size PVC earth wire 10/16/25 sq.mm shall be supplied by Railways. Note: At certain locations, it may not be possible to acheive earth resistance of less than 1.0 ohm with one earth electrode /pit due to soil resistivity. In such cases, provision of loop earth consisting of more than one earth pit shall be done, for interconnection of two earth pits copper tape of size( 25mmx2mm) or GI flat of size( 50mmx6mm) shall be provided by the contractor. The number of pits required shall be decided based on the resistance achieved for the earth pits already installed. The procedure mentioned above for one earth pit shall be repeated for other earth pits. The other earth so installed for the purpose of loop earthing arrangement shall be counted as seperate earth. (Inspection : RDSO for supply portion and installation by Site Engineer)"
10
26845
268455.5
... More
Supply fixing and wiring of fuse auto changeover system (FACS main system) as per RDSO/SPN/209/2012 Rev. 2.0 with latest amendments. One automatic changeover unit comprise 32 nos of external Non Deteriorating Type or 'G' type fuses of various Ampere Rating, working voltage- 24 19 VDC which are in signalling circuits. System shall have 8 cards with monitoring arrangement of 4 fuses in one card. .Installation , wiring, Testing and commissioning of Fuse Alarm System,it consists of fixing of modules of fuse alarm system on existing relay rack, wiring from existing fuses to modules, soldering, lacing etc will be supplied by the contractor. Installation to be executed without affecting the functioning of the existing Circuits/Gears (Inspection : RDSO for supply portion and Installation by Site Engineer)
5
41712
208563.5
... More
"Wiring of relays in relay room/relay huts as per appd wiring diagrams. All wiring 9 material including resistances and condensers etc. to be supplied by contractor. It also includes dressing, bunching , lacing and fixing of relay bases. (Cables and wires for wiring will be supplied by Railway). (Inspection : Site Engineer) "
100
479
47954
... More
Fabricating, writing and fixing of description boards made of ply 6mm thick with white 10 sunmica glued over its surface and 1"x1" wooden batton fitted all around on the rear and having alluminium angle size of 25.4mmx25.4mmx3.15mm on all four sides as per instruction of Engineer at site. All the materials to be supplied by contractor. (Inspection : Site Engineer)
10
2560
25604.4
... More
Supply, installation, commissioning of fault locator for short circuit detection in the fire alarm loop required as per UL listed solution and RDSO/SPN/217/2016. Ver 1.0 or latest. (Inspection : RDSO for supply portion and Installation by Site Engineer)
1
5827
5827.33
... More
Fixing of 1"/2" PVC channel/conduit pipe 1" dia on proper clamps and screws and indoor cable laying. All fixing material will be supplied by the contractor. (Inspection : Site Engineer)
100
14
1440
... More
Supply and installation of RFID electronic marker for S&T underground cable wlth 35 progammble memory for saving the user specific data inside the RFID electronic marker memory chip,later recordable by electronic marker locator during locating(1O cm diameter with floating coil to keep detection circuit always Horizontal for better detection) which can be buded to depth of 5ft Placing in trench. Inspection RITES
100
3155
315521
... More
Supply of shunt signal position light complete with lock, unit post and surface base mounting socket 90mm dia without holders bulbs etc. to drg.no.23840 adv. Or latest specs.no.IRS-S- 23/88 Independent post type. (Inspection : RITES)
2
9661
19322.74
... More
Supply of magneto telephones with all accessories including Standard battery box and 3 nos. of RR cells in the ASM office with crank handle locations/ K-points and interlocked L-xing gates as per instructions of the site Engr. Inspection : Consignee
5
5734
28672.85
... More
Laying of signalling/Telecom/power cables of different sizes as per approved Drg. No. NR/SandT/CON/1-1/97C and as per cable route plan approved by Railways and meggering of cable before and after its laying of all type of outdoor cables. (Inspection : Site Engineer)
120000
9
1118400
... More
Design, Fabricate & supply of EI system for Budhal Balamgarh halt station (BDBG) as per RDSO spec no RDSO/SPN/192/2019 ver 2.0 or latest with amendments & as per special condition of contract and technical specifications (including all relevant and latest RDSO Technical Advisory Note (TAN) and SIP enclosed mainly consisting of following: Central Microprocessor equipment with HOT standby architecture, Interface equipment as per RE requirement, interface suitable one operator main and one operator stand by VDU, interconnecting cables etc. All types of racks for relays & EI equipments, fixture mounting arrangements and accessories necessary to make EI system functional. Dual set of Video Display unit control terminal (VDU) having industrial grade fanless PC. The size of VDU minimum 55 inches single screen (as per latest RDSO specification and TAN) and it's furniture (work station & revolving chair) with UPS minimum four hour backup, maintenance terminal having industrial grade fanless PC with 47 inch LED monitor and it's furniture (Workstation and revolving chair) with UPS minimum four hour backup Supply, OFC connectivity (Patch Cords) as per requirement of system, All type of interface relays used in EI system and Supply, installation, wiring, testing, validation and commissioning of data logger system along with all interface equipment like a protocol converter,Modem & failure analysis system (with i7 or higher processor), etc. (required to connect data logger with EI system have to be supplied by contractor as per of this item) DC-DC converter required for EI (un-stabilized 230VAC or 110VDC from the battery set of IPS will be provided by railways), supply & installation of Earthing system of EI, lightening and surge protection device (class A,B,C and D) suitable for EI as per latest RDSO spec. and TAN and their connection with earthing arrangement and accessories necessary to make EI system functional . Note: Other details are included in special conditions of contract. 1. Tenderer may quote any RDSO approved EI system with complete details of all module, cards and accessories etc. Along with necessary spares (refer special condition of contract) as per RDSO spec. no. RDSO/SPN/192 of 2019 ver.2 with latest amendments. Please give full details of quantities for the station and unit base rates item wise, the total amount of which must be equal to the given LAR of this item in separate annexure after award . The rate quoted in percentage above/at par/below for entire tender shall be applicable for the rates quoted in schedule item no.1 2. System design should cater to accommodate 15% additional I/Os in future as per para 6.6 of RDSO spec. 3. Other details are included in special conditions of contract. (SIP/TSIP of stations are enclosed along with tender document. Inspection: RDSO- Any sub item which is not inspected by RDSO will be inspected by Consignee). one set per station = one lot
-
-
1
... More
All work of horizontal boring and trenchless cabling along with supply,transpotation and insertion of double wall corrugated pipe -( ISI marked ) conforming to RDSO Spec no. 32 RDSO/SPN/204/2011, and the laying of cable in the boring under the track / road etc as per instruction of site engg. by using pipe of size 120 mm outer dia, 103.5 mm inner dia in which required number of cables to be crossed. This includes laying of cables in trench. The depth of horizontal boring should be minimum 1.0 m from rail flange/road level. (Inspection : RITES for supply portion and Installation by Site Engineer)
900
2112
1901358
... More
Shifting of Apparatus case half and it includes the Excavation of pit in and around the existing location boxes very carefully without damaging the working cables and shifting and turning the location boxes to clear of the infringment as instructed by the railway repsentative at site. The 96 work includes ensuring the safety of the signalling system, releasing the cables coils to give access for shifting/ turning the location boxes. Necessary masonary work and earth work in and around the location boxes to the required level shall be done as instructed by the Railway representative at site, if the existing earth connection to the location boxes are disturbed the earth wires shall be the properly reconnected. (All materials required for the work shall be supplied by the contractor). (Inspection : Site Engineer)
4
3018
12073.16
... More
Supply and laying of 2nd class bricks in the trench and laying as per approved Drg. No.NR/SandT/CON/1-1/97A as per instructions of the site Engineer. (Inspection : Site Engineer)
64000
8
561280
... More
Supply of 2 Aspect colour light signal unit complete with-out holders, lamps, lenses and 54 signal transformer as per RDSO Drg. No. SA-23003 A/M (Adv), Alt-9 or latest . Specification no. IRS:S- 26/64 Rev 1 or latest. (Inspection : RITES)
9
17797
160177.23
... More
Charging of lead acid secondary cells of 80/120AH capacity as per standard charging 86 procedure (with contractor own charging equipments). All charging materials ie. Sulphuric acid conforming to latest IRS specs and distilled water as per IRS specs will be supplied by contractor. This also includes installation of secondary batteries, their interconnection and writing work. (Inspection : Site Engineer)
82
241
19763.64
... More
Supply of tool kit for JE/SE/SSE for Maintenance as per tech spec. given below: (1) Digital Multi Meter suitable for axle counter ranges 20 Amp AC/DC make protek 506 or similar- 1 no. (2) Digital clamp Multi Meter range up to 100 Amps for AC/DC current make SEW or similar - 1 no. (3) Leather Tool Bag for keeping tool kit -1 no. (4) Plier Sealing with sealing code bit -1 no. (5) Plier Wire 18 Cutting 8" make Taparia or similar -1 no. (6) Nose Plier 4" make Taparia or similar -1 no. (7) Wire Stripper - 1 no. (8) Screw Driver set mutli port type -1 set (9) Track shunt resistance .5 ohm -1 no. (10) Soldering Iron 230V AC/65 watt -1 no. (11) Soldering Iron 230V AC/35 watt with diffrerent type replacement soldering head - 1 no. (12) Soldering Iron 110V AC/35 watt -1 no. (13) Mesuring Tape steel 30 meters - 1 no. (14) Measuring Tape steel 5 meters - 1 no. (15) Rechargable Torch Superior quality -1 no. (16) File Flat 8" long - 2 nos. (17) File Round smooth 8" long - 2 nos. (18) File Flat Bsterred 8" long - 2 nos. (19) Electric Drill Machine Portable 6mm make wolf or similar -1 no.(20) megger 100V DC (Inspection : Consignee)
1
52561
52561.71
... More
Supply, installation, commissioning of end of Line box for linear Heat Sensing cable as per RDSO/SPN/217/2021, Ver 3.0 or latest. (Inspection : RDSO for supply portion and Installation by Site Engineer)
1
5233
5233.84
... More
Preparation of App. Case half not involving wiring of relays. Preparation and fixing of Bakelite hylum sheet 450x800x6mm and Backelite shelf 450x450x10mm duly fixed by angle iron piece of different size inside all the app. Cases. Hylum board shall be fixed on an angle iron frame of 25mmx25mmx3mm. Angle iron frame will be fixed in location box secured by nuts and bolts. This includes fixing of fuse ARA terminal and fixing and jamming of cable with 2 inch thick salwood plank provided at the bottom. This will include opening, pasting and jamming armour of each cable in the 47 hole drilled separately for each cable through the salwood plank and all cable entry points on location boxes, location huts, JBs relay room/battery room to be closed with suitable masonry Works covered with sand and plastering.Wiring description for terminal drawing of circuits, inside app. Case. Painting from out side as well inside with red oxide and aluminum paint is covered separately. Size of lettering will be 100mm or as per instructions of Engineer at site. All materials including Backelite shelf, hylum board, salwood plank, angle iron square bar, wire and wiring material with bases, catenary wires, nuts and bolts and other items shall be supplied by the contractor. ARA terminals, fuse with base only shall be supplied by the Railways. (Inspection : Site Engineer)
10
3808
38083.9
... More
Supply and laying screened wire twin core(24/76 copper conductors) PVC insulated 153 cable for connecting loudspeakers with GI support wire for connecting loud speakers (PVC channels / PVC conduit pipews/GI wire required for carrying the screened PVC cable shall be supplied and fixed by the contractor, however GI pipe for road crossing shall be supplied bythe railway, if required any where. Inspection : Consignee
300
104
31491
... More
Casting, concreting and curing of foundation of size (1160mmx760mm) at surface and 650mm deep as per approved Drg.No.NR/SandT/CON/2-7/97. It includes erection of single apparatus 39 case ,A layer of 3 mm of bitumen compound has to be provided between foundation and location box to prevent ingress of water in the base of location box . All material such as cement,coarse sand,aggregate,bitumen compound and anchor bolt shall be supplied by contractor . App. Case single will be supplied by Railway. Contractor is required to execute all type of repair Works of foundations if required during inserting the cable for termination. (Inspection : Site Engineer)
60
6521
391281
... More
Supply and installation of unit horn combination speakers(25Watts) & 100V line with LMT taps of 25W,15W,10W and 5W. Inspection : Consignee
5
2157
10787.25
... More
Supply of spare electric operated lifting barrier GI Boom as per latest RDSO Drg S- 11600 in maximum 4 sections of 8feet each. Inspection : RDSO
1
41344
41344.08
... More
Supply of End and Intermediate Plate 2.5mm/0.098 in Thick Wago or similar as per RDSO/SPN/189/2004 Ver.3.0 or latest. (Inspection : Consignee)
800
19
15296
... More
Supply of Steel carrier Rail 35x7.5mm/0.039 in thick unslotted, yellow with Chrome Wago or similar as per RDSO/SPN/189/2004 Ver.3.0 or latest. (Inspection : Consignee)
100
153
15342
... More
Supply, installation, testing & commissioning of 240 watts Audio Amplifier working on 230V AC/24VDC as per technical specifications given below:The model should be Philips/Bosch LBD 147 1916 or similar. (a) Power Source-230V AC & 24Volts battery. (b) Power out put - 240Watts r.m.s. (c ) Input - 4 balanced input/3 stereo line .(d) Frequency response - 50 Hz to 18 KHz(+1/-3db) (e) Distortion - <1%(at rated output power at 1 KHz) (f) Speaker of matching - 8 ohms & 70V/100V line. (g) Sensitivity - 1.0mV(mic input) (h) S/N - 75 db (i) Phantom power - Yes (on mic input 1). Inspection : Consignee
1
31532
31532.77
... More
Preparation of App. Case single not involving wiring of relays. Preparation and fixing of bakelite hylum sheet 910x800x6mm and Backelite shelf 900x450x10mm duly fixed by angle iron piece of different size inside all the app. Cases. Hylum board shall be fixed on an angle iron frame of 25mmx25mmx3mm. Angle iron frame will be fixed in location boxes secured by nuts and bolts.This includes fixing of fuses, ARA terminal and fixing and jamming of cables with 2 inch thick salwood plank provided at the bottom. This will include opening, pasting and jamming armour of each cable in the 42 hole drilled separately for each cable through the salwood plank and all cable entry points on location boxes, location huts, JBs relay room/battery room to be closed with suitable masonry Works covered with sand and plastering.Wiring description for terminal drawing of circuits, inside app. Case. Painting from out side as well inside with red oxide and aluminum paint is covered separately. Size of lettering will be 100mm or as per instructions of Engineer at site. All materials including Backelite shelf, hylum board, salwood plank, angle iron square bar, wire and wiring material , catenary wires , nuts and bolts and other items shall be supplied by the contractor. ARA terminals,fuse with base only shall be supplied by the Railways. (Inspection : Site Engineer)
20
5551
111028.6
... More
Supply of Portable digital auto range multi-meter clamp type Philips, Motwani, Fluke or 16 Rishabh make capable to measure from (0.1mv/0.01ma) AC/DC upto 50Amp(AC/DC), 600V(AC/DC) and 0.1 ohms- 40M ohms suitable for measurement of Freq., capacitance complete with Manual, leads, battery and holster etc. (Inspection : Consignee)
1
8572
8572.72
... More
Supply of OFC jumper (Patch card) 10mtr. long with FC/PC and SC or suitable connector at both end as per IRS:TC-81/2000 with latest amendment.(Inspection. Consignee)
5
654
3274.95
... More
Casting, concreting and curing of foundations for shunt signal/ F marker of size 63 (855mmx855mm) at bottom and (711mmx711mm) at top and 750mm deep as per approved Drg. no. NR/SandT/CON/2-1/97A. All material such as cement, coarse sand, aggregate and foundation bolts will be supplied by contractor. (Inspection : Site Engineer)
2
4066
8133.58
... More
Supply and Installation of Thermoshrink jointing kit for 6-Quad cable and PIJF cable for 129 Derivation/ Termination joints at LC Gates/Pump House/different locations as decided by the site Engineer as per IRS: TC-77/2012 (Rev.3) with amendment 1 and 2 or latest. This includes all materials required for joints.(Inspection : Consignee for supply portion and Installation by Site Engineer)
6
9052
54316.86
... More
Supply of sec. cell low maintenance 2 V/ 80 AH. conforming to IRS S-88/2004 Rev-1or latest with micro porous vent plugs cum floats with inter cell connectors, nuts,bolts,washers etc. (Inspection : RDSO)
82
3111
255124.96
... More
Supply of 3 phase Manual changeover switch 63Amps/100Amps. Siemens/ Havells or similar Iron Clad switch. (Inspection : Consignee)
2
5971
11943.54
... More
Supply of VF Tapping and Termination Transformers 2T/1120:470 Ohm as per IRS-TC- 22/76 with Amd 1 with latest amendments. (Inspection : Consignee)
5
2404
12021.65
... More
Jointing of signalling cable straight through M-seal joint kit for U/G signalling cables, it includes supply and provision of jointing kit. (Inspection : Site Engineer)
5
2217
11085.2
... More
Supply of 4 conductor dis-connect terminal block for test and measurement 0.8 20 sq.mm-2.5 sq.mm centre marking with test slot for test plug 2mm/0.079IN and 2.3mm/0.091IN carreir rail DIN 35 front entry cage clamp connection Grey wago or similar as per RDSO/SPN/189/2004 Ver.3.0 or latest. (Inspection : RDSO)
8000
121
968000
... More
Supply of OFC integrated acess device 1U height or 1.5 U height / 19 " rack mountable for LVCD / Digital axle counter purpose ; optical module integrated in the unit supporting dual core OFC and one 100Mbps Ethernet port for survilance / smoke detector ; optical distance support to be 20 91 kms ; unit to support one E and M module supporting four 2W / 4W ( each port configurable ) to support axle counter / UFSBI / Control phone / EC / RTU / and one TELNET / SNMP port ; unit to support DC / AC power supply ; unit to support change over mechanism between quad and optical fiber for E and M option ; one number cable to be provided along with unit for E and M ; FABIO / 2CX / OFC / DC and Module 2W / 4W four port : Make : TEAM ENGG / FABIO / WAVES or similar / TANSY. Inspection: RITES Note Item must be compatible with adjacent station.
2
265984
531969.78
... More
Supply and fixing of slotted angle iron with clamps and nut bolts of appropriate size on the poles/masts in the open parking area and installation of speakers on it. Inspection : Consignee
5
275
1378.5
... More
"Installation, testing and commissioning of High Availability Single Section Digital Axle Counter System complete by OEM or its authorised dealer. The axle counter will be High Availability Single Section type with two detection points and it is possible to install it without trolley protection track circuit. The axle counter must consist of following: (a) Mounting of high frequency TX and RX 90 coil-2 sets, each set consist of web mounting type 2 Nos. of TX and 2 Nos. of RX. TX and RX shall be supplied by Rly. (b) Mounting of track side digital axle counter Unit-2 Nos. (c) Fixing of vital relays etc. duly wired-2 Nos. (d) Clamping with deflector plate and hardware for mounting of two set of TX and RX coil. (e) Resetting arrangement of each axle counter. (f) All the wiring material required for installation and commissioning shall be arranged by contractor. (g) This also includes integration with existing SGE/Tokenless/Token block instruments were required as per instructions of site engineer. The wire and other wiring material will be arranged by contractor at site. Inspection: Site Engineer"
2
85531
171063.54
... More
Supply of Megger 500V DC Philips or similar make. (Inspection : Consignee)
-
-
38
... More
Earth work for excavation and refilling around location boxes, signals etc. where 108 necessary including 50m lead and 1.5m lift by excavation. The earth shall be rammed including breaking of clods, levelling and dressing. The earth work around the location/junction boxes/signalls shall be up to the plaster level and for width sufficient for the maintainer to attend the box both from front and back side. (Inspection : Site Engineer)
5
147
739.85
... More
Testing and meggering of all types of outdoor cables after its laying and termination on 37 both ends under supervision of Railway representative. This also includes preparation of test report for core to core and core to earth on prescribed proforma for each core of the cable seperately. This also include dressing and lacing of cable on both ends. Proforma for testing and material for lacing to be supplied by the contractor. (Inspection : Site Engineer)
8000
15
122400
... More
Fabrication, Supply and installation of wooden shelves(Teak wood ) 24" wide and 1.25" thick supported on angles 2" x 2" x .25" on three sides. This includes painting of angles and varnishing of shelves. All materials to be supplied by the contactor. (Inspection : Site Engineer)
5
6078
30390.4
... More
Supply and Installation of Deminelraliser plant of capacity 65 Litres per hour approx. 112 This includes all the pipe connections from water source to unit and also to collection unit as per instruction of site engineer. All the installation material will be supplied by the contractor. (Inspection : Consignee for supply portion and Installation by Site Engineer)
1
41415
41415.9
... More
Supply of calling-on colour light signal unit with offset bracket 3.5 inches dia. type drg.no.SA 24351-52(Adv) or latest .no.IRS-S-23/88. or latest. (Inspection : RITES)
2
4767
9535.02
... More
Supply and fixing of G.I. pipe 75mm/80mm dia, 3mm thick as per spec no IS-1239, perforated at a distance of 20 CM or less of required length at culverts/ bridges/along the cuttings, 31 suitably concreted at both ends as per approved drg. No.Drg. No.NR/SandT/CON/1-4/97.or at ASM office/other buildings suitably fixing it to the wall and at both ends. G.I. clamps of M.S. flats bolts and nut, to be supplied by the contractor. Inspection : Consignee for supply portion and Installation by Site Engineer)
200
920
184076
... More
Installation of Master VHF set 25W on ASM's table and wiring of the same with power supply wiring with 120AH VRLA batt. The 230VAC from IPS to be extended to the Power supply unit of 120 the VHF and provision of power socket. This includes foundation (500x500x1000mm) and erection of the 50mm GI pipe on roof top and fixing of Antenna with GI pipe ( mini. 6 mtr )and wiring from Antenna to the VHF set with provision of guy wires for support of the GI pipe. All the materials cement, sand, GI pipe, guy wires, power wire with socket etc.to be supplied by the contractor. VHF set, Antenna and 120AH VRLA batt. to be supplied by the Railway. (Inspection : Site Engineer).
1
7460
7460.34
... More
Supply of CAT 6 UTP cable (23 AWG). It shall comply to TEC BR NO TEC/GR/SLC-01/02 Aug 05 (TEC Standard Number TEC 52010:2005) with latest amendments Inspection Consignee
200
22
4518
... More
Supply, installation, commissioning of circuit integrity cable 2 core 1.5 Sq.mm as per RDSO/SPN/217/2021, Ver 3.0 or latest. (Inspection : RDSO for supply portion and Installation by Site Engineer)
250
289
72305
... More
Supply of single app.case steel RE with E type lock and key ward no.42 and handle as per drg. No. RE/SandT/ALD/SK/219/82 and 221/82 with Alt.B. (Inspection : RITES)
-
-
40
... More
Preparation of App. Case half as Battery Box (not requiring shelf and hylum of size 450x150x6mm only is reqd.) Preparation and fixing of bakelite hylum sheet 450x150x6mm Hylum board shall be fixed on an angle iron frame of 25mmx25mmx3mm. Angle iron frame will be fixed in location box secured by nuts and bolts. This includes fixing of fuse ARA terminal and fixing and jamming of cable with 2 inch thick salwood plank provided at the bottom. This will include opening, 48 pasting and jamming armour of each cable in the hole drilled separately for each cable through the salwood plank and all cable entry points on location boxes, location huts, JBs relay room/battery room to be closed with suitable masonry Works covered with sand and plastering.Wiring description for terminal drawing of circuits, inside app. Case. Painting from out side as well inside with red oxide and aluminum paint is covered separately. Size of lettering will be 100mm or as per instructions of Engineer at site. All materials including hylum board, salwood plank, angle iron square bar, wire and wiring material catenary wires, nuts and bolts and other items shall be supplied by the contractor. ARA terminals only shall be supplied by the Railways. (Inspection : Site Engineer)
5
2741
13709.55
... More
Supply, installation and wiring of Earth leakage detector (12 Channels) for monitoring 15 different AC and DC, supplies including all accessories as per . specfication no. RDSO/SPN/256/2002 or latest and stipulations of tender docment. Installation to be done by OEM. A certificate to be submitted by the contractor.(Inspection : RDSO for supply portion and Installation by Site Engineer)
1
168651
168651.87
... More
Supply and Installation of 20 pair DP box made of cast Aluminium with in built locking system and water proof should have double outlet with leadig in brass nozzle.The main tag block plate is mounted on the inner aluminium chamber with brass terminal studded in back lite sheet. DP boxes 119 and termination of cables as per specifications, drawing and stipulations of tender documents. . This includes fixing of the same on 1" thick board of size as pesr directions of site engineer with ground nuts and bolts of suitable size and pipe fixed with clamps on pole /wall . All materials required for fixing and termination including salwood/hylum board and the hardware required for fixing will be supplied by contractor. (Inspection : Consignee for supply portion and Installation by Site Engineer)
5
1652
8264.2
... More
Installation of Point track circuit having single point (excluding traps) DC track circuits to suit RE area as per std. Practice. This will include following as per site requirement:- (a) Drilling of holes 7.2 mm dia or size as required provision of continuous G.I. wire bonding on switch portion and crossing of point with two bonds wires and two clips duly fastended with fish plates and bolts at each joints including transverse bonding with rope wire. 8 SWG G.I. soft bond wire, Channel bond pins and all other material required will be supplied by contractor. (b) Jumpering from rail to rail or to track lead junction box including polarity jumpers/cables as per track jumpering/ insulation diagram. This includes terminating the jumpers in the TL JB and fixing the jumper on the sleeper as per instructions of Engr. at site. (c) Fixing of insulated block joints complete with provision of skimmed fish plate. Fish plates shall be supplied by the Railways but skimming to be done by contractor. Supply of insulation 84 materials for insulated block joints will be supplied by Railway. (d) Fixing of TL JBs as per drg. No. (NR/SandT/CON/3.2/97) along with concrete foundation and plastering on both ends i.e. T.F. and TR end and for polarity changers as per the track jumpering/ insulation diagram. All material for fixing including angle iron shall be supplied by the contractor. This also includes supply and fixing of TL JBs with provision of M-6 terminals. TLJB to be written with track circuit number. (e) Prov. and wiring in the app. Cases/relay huts of T.F. battery charger, TF resistance 30 Ohms, track relays, choke B type (at Feed End and Relay End) and batteries as per the standard practice using fuses and terminals. This all include supply of all material by contractor except supply of TF battery charger, batteries, relays.Supply of TF battery charger, batteries, relays will be done by the Railway. (f) Commissioning of track circuits as per prov.of para of IRS specn. S-36/87 Amd 2. This includes adjustment of track feed resistance, testing with train shunt resistance. This also includes preparation of track history cards. Track history card should be supplied by the contractor. (Inspection : B- type Choke, track resistance and fuse by RDSO
8
23997
191982
... More
Supply and Installation of Annunciator (Multiway Telephone Exchange) 10 lines as per 121 RDSO Drg No TCA-3352 (Adv.) or latest. It includes installation of Annunciator. All fixing material, wire etc will lbe supplied by contractor.(Inspection : Consignee for supply portion and Installation by Site Engineer)
2
9803
19606.26
... More
Installation and Commissioning of block proving with digital axle counter as per IRS: S- 105/2012 using UFSBI and block panel for single line/ Double line operation. Wiring material 89 (16*0.02mm flexible wire etc) and any signalling material for installation and commissioning of system shall be supplied by the contractor at site. PPCL to be filled by OEM authorised/reperesentative. Inspection :Site Engineer.
2
80951
161903.34
... More
Supply and Laying of HDPE duct in the trenches, including in HDD/Manual Boring and supply pulling of Nylon rope through is at different places as per direction of Engineer incharge/ site 131 Engineer. It includes Supply of HDPE duct outer dia 40mm and inner dia 33mm as per TEC Gr No. G/CDS-08/02 Nov /2004 with latest amendment with end cap to be provided along with the drum at both ends . (RDSO specs No. RDSO/SPN/TC/45/2013 revi 2.0) (Inspection : Consignee for supply portion and Installation by Site Engineer)
1
73854
73854.52
... More
"Supply of ""As built"" Documents. (i) Completion Documents as per condition of Contract. (6 Sets for each EI) (ii) Supply of documents as per Technical specification Para - 10.2 of 3 RDSO Specification no RDSO/SPN/192/2019. (i) Supply of 6 copies of completion set of superior quality paper, laminated, properly bound in steel clip jaw file with cushioned cover.(ii) Software back up of complete set in the form of Pen Drive. (iii) One complete set of tracings.(iv) Design through CAD (v) Drawings in A3 and plans in bigger size. (six sets). (6 Sets for each EI). (1 Set=1 Set per Station) (Inspection: SSE/DandD)"
1
91384
91384.44
... More
Spiral Binding of master of SWR & 02 set of photocopies as above including plastic cover. Inspection by SSE/C/D&D.
5
59
299.3
... More
Supply of OFC jumper (Pigtail) 10mtr. long with FC/PC and SC or suitable connector at both end as per IRS:TC-81/2000 with latest amendment. (Inspection. Consignee)
5
490
2451.5
... More
Supply and installation of optical fibre cable joint enclosure as per TEC spec no. 138 GR/OJC-02/01/March 99 with latest amendment and splicing of optical fiber cables (24 fibers and testing) . This includes provision of joint pit (RCC/Prefabricated) as detailed in the technical specifications and as advised by Engineer at site. (Inspection : Consignee for supply portion and Installation by Site Engineer)
3
19123
57370.5
... More
'Supply &installation of 20 watt coloumn speakers with 10 watt taping with matching transformer and drive unit as per model no.LBD 8373 of Philips make or SCM-30T of Ahuja make or SHORE make Inspection : Consignee.
5
2768
13841.05
... More
Casting, concreting and curing of foundation of size (670mmx760mm) and 650mm deep as per Drg.No.NR/SandT/CON/2. 8/97 it includes erection of Apparatus case half. A layer of 3 mm 44 of bitumen compound has to be provided between foundation and location box to prevent ingress of water in the base of location box . All material such as cement,coarse sand,aggregate,bitumen compound and anchor bolt shall be supplied by contractor . App. Case half will be supplied by Railway. Contractor is required to execute all type of repair Works of foundations if required during inserting the cable for termination. (Inspection : Site Engineer)
20
5708
114166.4
... More
Supply and Installation of 10 pair DP box made of cast Aluminium with in built locking system and water proof should have double outlet with leadig in brass nozzle.The main tag block plate is mounted on the inner aluminium chamber with brass terminal studded in back lite sheet. DP boxes 118 and termination of cables as per specifications, drawing and stipulations of tender documents. . This includes fixing of the same on 1" thick board of size as pesr directions of site engineer with ground nuts and bolts of suitable size and pipe fixed with clamps on pole /wall . All materials required for fixing and termination including salwood/hylum board and the hardware required for fixing will be supplied by contractor. (Inspection : Consignee for supply portion and Installation by Site Engineer)
5
1132
5661.05
... More
Installation, erection and wiring of LED lit calling-on/dependent shunt signal /illuminated A marker/ AG marker/ F markers on the same post below main signal on offset bracket. Which also includes fixing of stencil and hoods, wiring and focussing of the signal. Offset brackets, calling on signal/shunt signal complete will be supplied by Railways. U-bolt for offset bracket and wire and wiring material will be supplied by contractor. (Inspection : Site Engineer)
6
1065
6394.38
... More
Brick work with well burnt bricks in foundations and plinths with cement and sand (ordinary) mixture of 1:4 ratio. All material is to be supplied by the contractor. (Inspection : Site Engineer)
2
3609
7219.04
... More
Fabrication, supply and fixing of relay racks of size 2200mmx690mm (as per approved Drg. No. NR/SandT/CON/4-3/97A) made of angle iron size 45mmx45mmx6mm alongwith outer frame made of angle iron size 65mmx65mmx8mm, fitted with M.S. squares bars duly galvanised, 6 descriptions strips to accommodate Plug-in-type relays/groups/Point contractor units/ECRs/HMUs. All fixing material like antilting device, hylam sheets if required, bolts and nuts, washers, insulators, shoe, angle irons, flats, L-bolts, Catenary wires and cement concrete etc. will be supplied by the contractor. This includes cleaning, priming by red oxide, painting and description etc. with ISI mark paints. (Inspection: Site Engineer)
4
19696
78785.92
... More
"Supply of Instruments / Tool Kits suitable for EI commissioned:* Tool kit and Measuring 4 Instruments for technicians / Jr. Engineers for Testing, Maintenance at Site and Instuments and Tool Kit required for trouble Shooting and repair at site. Note: Details of tool kit item is enclosed in Annexure -V/Vol.II of tender document. (1 Set=1 Set per Station) (Inspection : Consignee) "
1
145451
145451.84
... More
Alteration of wiring in existing apparatus cases single/half. All materials in connection with alteration in wiring shall be provided by the contractor. Relays, ARA terminals only shall be supplied by the Railways. (Inspection : Site Engineer)
5
4927
24637.15
... More
Supply of screw less end stop 10mm/0.394 in wide carrier rail DIN 35 Grey Wago or similar as per RDSO/SPN/189/2004 Ver.3.0 or latest. (Inspection : Consignee)
400
16
6676
... More
Supply of 3/4 Aspect colour light signal unit complete with-out holders, lamps, lenses 55 and signal transformer as per RDSO Drg. No. SA-23001 A/M (Adv), Alt-9 or latest and SA- 2302A/M(Adv), Alt 9 or latest respectively. Specification no. IRS:S-26/64 Rev 1 or latest. (Inspection : RITES)
6
22773
136643.94
... More
Installation, testing and commissioning of EI equipments supplied, including transportation from consignee depot to site at stations listed above. Installation is to be done as per 2 RDSO specification 192/2019 and RDSO practice circulated vide TAN no. STS/E/TAN/3012, Ver. 2.0, Dt.10.08.2016, TAN no. STS/E/TAN/3007, Ver. 1.0, Dt.02.11.2012 for industrial grade PC and TAN no. STS/E/TAN/3006, Ver. 1.0, dt. 02.11.2012 for earthing and bonding scheme for Electronic Interlocking. (1 Job=1Station) . (Inspection:Site Engineer)
1
407895
407895.41
... More
Installation of 120mm/90mm dia HDPE double Wall Corrugated (DWC) Duct as per as per RDSO Specification No. RDSO/SPN/204/2011 Ver. 1.1 With Amndt-1 (outer dia 120mm in 6m st. 30 length with one coupler for every 6m length). All the materials cement, sand etc. are to be supplied by the contractor. This include brick work and other arrangements required to secure the pipe as per specifications, drawings and stipulations of tender documents and as per approved cable route plan including road crossing/platform/track crossing and for bridges and culverts etc. (Inspection : Site Engineer)
200
87
17438
... More
"Fixing, wiring, testing and adjustment of point machines as per standard practice. It also includes :- i) Fixing of switch extension 'P' bracket/'D' bracket, providing insulation for switch extension bracket, fixing ground connections, adjusting the correct opening of switches and adjusting the point machine with crank handle. ii) Wiring inside the point machine, wiring of JB with lock and key as per drawing, provided with terminal strips for cable terminations. iii) Supply and fixing of GI pipes with flange for taking cable in to point machine and jn. Box through gland/GI pipe. iv) Complete installation of point insulation , GI pipe, gland pipe, angle iron of size 75mmx75mmx10mm, channels 71 for fixing the machine, lugs for point rodding and insulation for stretcher bar 90R/52kg/60kg as per . drg.no.SA-23172 (adv.) Alt.1 will be done by the contractor. v) Smithy and fitting work required at site for complete installation of Gauge tie plate and insulation of GTP as per approved Drg.no.NR/SandT/CON/7-6/97 and william stretcher bar (if reqd.) will be done by the contractor. Machine shall be overhauled by contractor if required. vi) This includes removal of existing gears and fixing the machine at raised level on channel as per standard practice to avoid flooding wherever required. vii) Supply of point machine, ground connections of electric point machine, Jn. box , non insulated GTP and CTP extension plate, and stretcher bar with insulation material shall be made available by the Rlys. (Inspection : Site Engineer)"
12
9469
113635.08
... More
Training for Rly. Tech./JE/SE/SSE/Officer by OEM in installation, testing and commissioning, maintenance and trouble shooting of EI system complete including supply of hard/soft 5 copies of course module for each trainee. Competency certificate to trainee to be issued by OEM. All arrangements including classroom, lab, equipment, measuring instruments etc. required for the training should be satisfactorily arranged by the contractor at their own cost. (Inspection/Supervision : Site Engineer)
6
801
4807.26
... More
Supply of anti static mats of size 1 mtr x 0.75mtr& 3mm thickness Inspection : Consignee
10
2160
21602.7
... More
Installation, erection and wiring of independent position light shunt signal/ F 65 marker.This includes fixing of shunt signal, surface base signal post,LED signal unit/ lenses, lamp hood and wiring of shunt unit and focussing the signal. All material such as wire,nutand bolt etc. will be supplied by the contractor. (Inspection : Site Engineer)
2
1287
2574.28
... More
Supply and fixing of 50 mm wide Red/Yellow coloured retro reflective highlighter 77 marker tape made of non-metalized polycarbonate micro-prismatic lenses confirming to AIS 90 specification for fixing on BSLB/SLB boards/Stop signals/LC gates Make 3M India Ltd or equivalent. Inspection Consginee
10
644
6443.9
... More
"Supply of 2 MB programmable primary digital drop multiplexer with conference facility and with all common cards like processor card , power supply unit , remote control supervision etc.fitted in sub rack wired for 30 channels along with all other accessories and installation materials 144 and all instruction manuals as per RDSO specn. no IRS TC-68/04 or latest inspection by RDSO. (i) 2W/4W EandM/VF Interface Card (min 4 Ckt per card) x 4 Nos(Total 16 Ckts) (ii) Exchange Loop Interface Card (min 4 Ckts per card) x 1Nos(Total 4 Ckts) (iii) Subscriber/Hotline Interface Card (min 4 Ckts per card) x 1 No(Total 4 Ckts) (iv) 64 Kbps G.703 Data Interface card (min 4 Ckts per card) x 1 No (Total 4 Ckts). Inspection : RDSO Note Item must be compatible with adjacent station."
1
132323
132323.03
... More
Shifting of existing color light signal with foundation along the track to meet the schedule of dimension required in connection with RE modification. (Inspection : Site Engineer)
1
27347
27347.26
... More
Supply of QTA2 relays AC immunised plug in type DC 9 Ohm neutral track relay miniature tractive armature with 2F/1B contacts as per BRS : 939A or latest amendments if any, BRS :966 Append F2, IRS-S-34 and IRS-S-23 and IRS-S-60 (as applicable). (Inspection : RDSO)
20
5718
114378.6
... More
"Supply of ESM/TCM furniture of Godrej or similar make consisting of the following :- 1. Executive revolving bearing series low back floating chair with normal arms cushioned Chair : 1No. 2. 114 Executive Table size 72x36x30"" with 3 drawers one side, lockers cabinet on other side : 1No. 3. Visitor chair seat and back cushion with high density Foam with plastic PVC handle capsul type Flat pipe duly Painted black : 3Nos. 4. One Steel Almirah of size 48""x30""x17"" with lock and handle arrangement for record keeping at station. (Inspection : Consignee) "
2
46669
93338.16
... More
Supply of Colour light signal post 4.6Mtr and ladder 4.5Mtr and bases as per tech. spec. IRS-S-6-81, Rev-3 or latest.(Inspection : RITES)
9
21123
190114.92
... More
Supply, installation, commissioning Heat and Smoke Multi sensor detector with 99 automatically adjusts sensitivity levels without the need for operator intervention or programming sensitvity increase with heat varying and floating sensitvity from 0.5 to 4%/Ft and shall be plug in type facility and address through switch. The base should also be supplied as per RDSO/SPN/217/2016. Ver 1.0 or latest. (Inspection : RDSO for supply portion and Installation by Site Engineer)
15
6018
90280.95
... More
Supply and installation of Dynamic microphone with flexible goose neck and ON/OFF swithc provided with 6 metres mic lead along with suitable connectors. Inspection : Consignee
2
2770
5540.48
... More
Excavating and refilling of trench in Normal Soil to the level of ground with rammed 26 earth as per approved Drg. No.NR/SandT/CON/1-1/97A. Aso as not to form a drain 0.3 Mtrs. Wide and 1 Mtr. Deep on both side of the station alongside the track. It shall conform to the safe distance as per signalling and cable plan. It also includes clearance of rooots of trees and bushes. (Inspection : Site Engineer)
8000
82
659680
... More
Supply of shunt signal position light with lock, unit offset bracket 3.5 inches dia. without holders bulbs etc. to drg.no.SA 23840(adv) to SA 23848 (adv), spec no .IRS-S-23/88 Dependent post type. (Inspection : RITES)
6
9923
59541.48
... More
Toolkit for testing and maintenance of HASSDAC (As per Annexure VI/Vol-II) (Inspection : Consignee)
1
130202
130202.85
... More
General concrete work in cement, coarse sand and aggregate ratio 1:3:6, work 109 scattered at different places for items not covered in above schedule and fine plastering of top will be done with cement sand ratio of 1:4 . Volume of foundation also includes volume of C.I. base, anchor bolts etc. Coarse sand, aggregate 25mm and cement to be supplied by contractor. (Inspection : Site Engineer)
5
3482
17411.25
... More
Supply, installation, commissioning of analogue addressable UL listed Fire alram Control Panel with 80 character display with battery charger and battery , backup for 24 Hr normal 100 operation and 15 Min alaram operation addressable power supply and alphnumaric keypad for installation for the FAS panel and 1000 event recording facility without GSM interface module as per RDSO/SPN/217/2016, Ver 1.0 or latest. This includes supply of patch/loop cards in huts if required. (Inspection : RDSO for supply portion and Installation by Site Engineer)
1
531215
531215.09
... More
Supply of apparatus case steel RE half with E type lock and key ward no.42 and handle as per drg.no. RE/SandT/ALD/SK/220/82 and 221/82 with Alt.B. (Inspection : RITES)
25
19295
482388.75
... More
Supply and Installation of emergency sliding boom comlete with all acessories for L/B gate. Inspection : Rites
1
289457
289457.51
... More
Supply of 4-Wire DTMF base way station eqpt. consisting of the following : i) Supply of 116 4 wire way station equipment as per IRS-TC@45<45@2007 of latest complete with 4 wire control telephone as per IRS-TC@45&45@97 with latest amendment suitable to work on 4/6 quads- ii) Supply of Battery charger/power supply unit 230VAC/12VDC with battery back up of 12V/7AH as per IRS-TC- 72/97 or latest-1 no. (Inspection : Consignee)"
4
9172
36690.8
... More
Fabrication, Supply and fixing of retroreflective P/G/C/A markers with complete fittings 66 as per approved Drg. No. NR/SandT/CON/6.2/97. All material required for the job such as MS sheet, MS angle. Nut and bolts will be supplied by the Contractor. The P and G markers shall be as per Drg. No.S 23456(Adv) and SA 23477(Adv) respectively. (Inspection : Site Engineer)
5
838
4194.45
... More
Blowing/ Drawing of OFC cable in the HDPE duct 40mm/33 mm by mechanical system. (Inspection : Site Engineer)
1
11803
11803.11
... More
"Installation, erection and wirng of 2/3/4 aspect LED lit colour light signal including 1/2/3/4/5/6 way Jn. type/Stencil/Theatre type route indicator Fixing of CLS surface base, bolting on the foundation. Erection of CLS post with signal unit on the top or on an off-set bracket and fitting ladder and guard to the post at the top. Concreting ladder base and embedded into the ground with supporting bracket in the middle, blanking of the ladder for a distance of 1 feet between the height 6' 9" and 7' 9" from the rail level by MS angle and MS sheet 6mm thick wherever required. This includes provision of wooden (SAL) cross arm 1 mtr x 1 mtr for CLS unit prior to the commissioning, fixing of LED aspect, current regulator and hoods of CLS unit, terminating cables, wiring the CLS unit and 59 focusing the signal. Elevation and distance of foundation from track shall be in accordance with schedule of dimension for Indian Railways and as per NR practice. All items for the above Works except Signal unit, LED signal, Signal post, Base and Ladder shall be supplied by the contractor including but not limited to the following: i) "U" bolt for offset brackets, ii) Wooden cross arm 1 mtr. x 1 mtr., iii) MS angle and MS sheet for blanking of ladder,iv) Supply and fixing of signal number plate (retro reflective) with complete fittings as per standerd railway practice. v) Wire mesh guard, lock for unit if required, nuts, bolts etc . This also includes fixing of route indicator on the top of the signal post or on offset bracket including fixing of offset bracket, wiring the whole unit, focussing of signal and route indicators. All items for installation and erection to be supplied by the contractor. Wiring and other fixing material, 'U' bolts will also be supplied by the contractor. (Inspection : Site Engineer)"
2
4504
9009.84
... More
Supply of track feed batt. charger 110VAC/2-4-6 VDC / 10 Amps as per RDSO spec. no. IRS: 89/2013 (Amd 1) or latest from RDSO appd. Firm. (Inspection : RDSO)
26
4460
115963.9
... More
Supply of electric fuse complete with fuse block(base) for Railway signalling non- 13 detoriorating type low voltage fuse assembly 2Amp/4Amp/10 Amp/16Amp. to suit . Specn. No.IRS: S- 78/2006 and fuse block made of PBT/Polycarbonate as per IRS: S-75/2006 (Rev-2 and Amd 2 ) and drg no. 23748 (IRS) Alt.4 or latest. Fuse block shall be suitable for round head type fuses. Rating : 2Amp/4Amp /10 Amp/16Amp'. (Inspection : RDSO)
300
204
61236
... More
Supply and Installation of ISI marked Carbon di Oxide type (BC) fire extinguisher of 4.5 Kg capacity confirming to IS: 2878 from seamless cylinder confirming to IS: 7285 with IS marked 107 control value conforming to IS: 3224 high pressure myr. Long discharge hose and horn complete with initial gas charged with carrying handle and wall mounting braket etc. as required by site Engineer. It includes installation of fire extinguisher with accessories . All fixing material wall mounting bracket , nut and bolts will be supply by the contractor. (Inspection : Consignee for supply portion and Installation by Site Engineer)
10
10548
105487.6
... More
"Fabrication, supply and fixing of cable termination board of size 2200mmx900mm as per Drg. No. NR/SandT/CON/4-1/97A made of angel iron size 40mmx40mmx5mm alongwith outer frame made of angle iron size 65mmx65mmx8mm duly fitted with Bakelite sheet (HYLAM MAKE or 7 similar ) of size 6mm thick. This also includes fixing of ARA terminals/strips/Wago connectors and fuse bases etc. Supply and fixing of hard wood of size 70cmx25cmx5cm in the back at bottom for jamming of armour of cables, each cable in the hole drilled separately for each cable through the salwood plank and all cable entry points on location boxes, location huts, JBs relay room/battery room to be closed with suitable masonry Works covered with sand and plastering. All the fixing materials like bolts, nuts, washers, Insulators, shoe, angle irons, flats, L- bolts, Catenary wires and cement concretes etc. will be supplied by the contractor. This includes cleaning, priming by red oxide, painting and description etc. with ISI mark paints. (Inspection : Site Engineer) "
5
21752
108764.1
... More
Engaging mechanical excavators like JCB or other machineries for regarding and 113 leveling the formation, dismantling any infringing structures, clearing and removing debris etc., with all lead and lifts etc., complete and as per the instruction of railway representative at site.( Inspection: Site Engineer)
5
1035
5177.25
... More
Supply of closed racks complete (545mm x 564mm x 2090mm) with all fittings for housing SDH equipments, primary Mux, FDF, DDF, MDF using krone module and other equipments like 143 runway ladders etc. completely wired and equipped with integrated protection modules for all channels as per technical specifications and other stipulations of tender documents. It should be possible to lock all the equipments with only order wire telephone remaining outside the rack. Inspection : Consignee
1
51276
51276.1
... More
Installation, erection, wiring of 2 aspect color light signal. Fixing of CLS surface base, bolting on the foundation. Erection of CLS post with signal unit on the top or on an off-set bracket and fitting ladder and guard to the post at the top. Concreting ladder base and embedded into the ground with supporting bracket in the middle, blanking of the ladder for a distance of 1 feet between the height 6' 9" and 7' 9" from the rail level by MS angle and MS sheet 6mm thick wherever required. This includes provision of wooden (SAL) cross arm 1 mtr x 1 mtr for CLS unit prior to the commissioning, 57 fixing of LED aspect, current regulator and hoods of CLS unit, terminating cables, wiring the CLS unit and focusing the signal. Elevation and distance of foundation from track shall be in accordance with schedule of dimension for Indian Railways and as per NR practice. All items for the above Works except Signal unit, LED signal, Signal post, Base and Ladder shall be supplied by the contractor including but not limited to the following: i) "U" bolt for offset brackets,ii) Wooden cross arm 1 mtr. x 1 mtr.,iii) MS angle and MS sheet for blanking of ladder,iv) Supply and fixing of signal number plate (retro reflective) with complete fittings as per standerd railway practice. v) Wire mesh guard, lock for unit if required, nuts, bolts etc for the following: (Inspection : Site Engineer)
9
3163
28471.95
... More
Supply and installation of mettalic rack(front panel)lockable and removable)to house the above amplifier com cassette player and 2 sets of 12V/80AH lead acid maintenance free battery and battery charger as per specification. Inspection : Consignee
1
14451
14451.26
... More
Supply of Relay AC immune ,plug in type,style QBAT, DC biased track, 9 ohms 24 V DC 17 2F/2B contacts, front & back contacts metal to carbon with plug board retaining clip conforming to RDSO/SPN/84, Ver 2.0 Alongwith IRS:S-23, S-34 & IRS:S-60 (as applicable). The interlocking code for this unit shall be ABEJX. Inspection : RDSO
6
6473
38841.24
... More
Casting, concreting, curing of foundations of size (400mmx300mm) at surface and 1000mm deep and erection of retroreflective SLB/BSLB/SB/ calling on boards/stop dead 67 boards/GoodsWarningBoard/PassangerWarning Board as per drg. No. NR/SandT/CON/7.4/97 and provisions of SEM. Supply of SLB/BSLB/SB/ calling on boards/stop dead boards/ GoodsWarning Board/ PassangerWarning Board as per approved Drg. No.SA-2373 or latest will be Supplied by the contractor. (Inspection : Site Engineer)
5
10120
50602.9
... More
Supply of Switch board PVC Telecom cable as per IRS specificaion no. IRS TC-24/91 Make delton or similar 5 pair/0.6mm (Inspection : Consignee)
200
46
9330
... More
Supply, Fixing and wiring of magneto telephones with all accessories including 115 Standard battery box and 3 nos. of RR cells in the ASM office with crank handle locations/ K-points and interlocked L-xing gates as per instructions of the site Engr. All fixing materials including Standard battery box and 3 nos. Of RR cells to be supplied by the contractor. Inspection : Consignee
4
5882
23529.72
... More
"Cleaning , Scrapping , Painting and lettering of all newly installed and existing gears such as signals, point equipment, track circuit equipment with T.C. no on rail app. Cases JB. TL JBs point rodding cranks, compensators etc. including gate equipment if existing in station section as per 111 the provision of IRSEM. All paints (ISI marked) shall be approved by Railway Engr. and painting material to be supplied by the contractor. This item also includes writing and painting requirement of all indoor and outdoor gears along with making of all circuit nos. near terminal and terminal boards/track in app. Cases, junction boxes, relay room, SMs room, writing of relay nomenclature fuse nos. and equipment nomenclature as the approved plans and as per provision of IRSEM. (1 Job=1 Station).(Inspection : Site Engineer)"
1
25693
25693.08
... More
Installation, wiring and commissioning of 2 MB programmable drop /insert MUX with 145 conference facility fully wired for 30 channels along with power supply and equipped for various types of interface cards as per site requirements. This includes shifitng and installation of existing MUX. All materials required for the work shall be supplied by contractor. Inspection : Site Engineer
1
13989
13989.1
... More
Cutting of passenger plateform wall 150mm X 150mm deep to provide 25mm GI dia 141 pipe inside the groove & repairing plateform wall by 50mm thick, CC flooring (1:2:4) & 100mm thick (1:4:8) & disposal of rubbish as per direction of site Engineer of railway as a complete job. This item includes all materials required to be supplied by contractor. Inspection : Site Engineer
100
56
5650
... More
Installation of Berthing and straight DC track circuits to suit RE area as per std. Practice. This will include following as per site requirement :- (a) Drilling of holes 7.2 mm dia or size as required provision of continuous G.I. wire bonding on switch portion and crossing of point with two bonds wires and two clips duly fastended with fish plates and bolts at each joints including transverse bonding with rope wire. 8 SWG G.I. soft bond wire, Channel bond pins and all other material required will be supplied by contractor. (b) Jumpering from rail to rail or to track lead junction box including polarity jumpers/cables as per track jumpering/ insulation diagram. This includes , terminating the jumpers in the TL JB and fixing the jumper on the sleeper as per instructions of Engr. at site. (c) Fixing of insulated block joints complete with provision of skimmed fish plate. Fish plates shall be supplied by 83 the Railways but skimming to be done by contractor. Supply of insulation materials for insulated block joints is not included.(d) Fixing of TL JBs as per drg. No.(NR/SandT/CON/3.2/97) along with concrete foundation and plastering on both ends i.e. T.F. and TR end and for polarity changers as per the track jumpering/ insulation diagram. All material for fixing including angle iron shall be supplied by the contractor. This also includes supply and fixing of TLJBs with provision of M-6 terminals. TLJB to be written with track circuit number. (e) Prov. and wiring in the app. Cases/relay huts of T.F. battery charger, TF resistance 30 Ohms, track relays, choke B type (at Feed End and Relay End) and batteries as per the standard practice using fuses and terminals. This all include supply of all material by contractor except supply of TF battery charger, batteries, relays.Supply of TF battery charger, batteries, relays will be done by the Railway.(f) Commissioning of track circuits as per prov.of para of IRS specn. S-36/87 Amd 2. This includes adjustment of track feed resistance, testing with train shunt resistance. This also includes preparation of track history cards. Track history card should be supplied by the contractor. (Inspection : B- type Choke, track resistance and fuse by RDSO
16
14952
239236.48
... More
Supply and Installation of Thermo shrink jointing kit for 6-Quad/4-Quad cable for 128 straight through joints as per specifications, drawings and stipulations of tender documents and as per approved cable route plan at various locations. Jointing kits to be supplied as per RDSO specification IRS:TC 77-2012 (Rev.-3) or latest amendments. (Inspection : Consignee for supply portion and Installation by Site Engineer)
6
7594
45566.4
... More
Supply and installation of earth electrodes as per std. practice. The item includes digging of pit in earth, 3 Mtrs. deep and fixing earth electrode pipe. Casting of cement concrete enclosures as per drg. No. (NR/SandT/CON/6.4/97). The soil treatement shall be done as per std. pratice. The item includes provn. of mild steel flat of size 35mm x 6mm (as per IRSEM) and nut bolted connection of MS flat with earth electrode. The other end of mild steel flat to be connected to block 94 instrument, cable sheath of power equipment, signal base, signal unit, route indicator apparatus case, LC Gate Pedestal, Boom Lock Post, Operating Panel of LC Gate. CT rack / relay racks, other equipments as per the instruction of Engr. at site and IRSEM. Earhting connection location to location,Earth pit to block instrument, CTR/Relay Rack and any other indoor equipment shall be done through cable for which cable shall be provided by Railway. Complete materials such as earth electrodes as per drg. No. ( NR/SandT/CON/6. 3/97), cement, wiring material, nut bolt for connection and mild steel flat of size 35mm x 6mm or 210 sqm as per SEM etc. to be supplied by the contractor. (Inspection : RDSO/RITES for supply portion and Installation by Site Engineer)
50
3674
183715
... More
Supply, installation and wiring complete KLCR and its box in ASM office /LC Gate or fixing in L-Box. Supply of Key Lock Relay(KLCR) type TMA 24V DC with 2F/2B contact configuration with different wards combinations as per RDSO Specificatins. Supply, installation, wiring of heavy duty 73 push button, LED indicator on MS sheet as per N.R. practice for crank handle locking. This work includes fixing and wiring of magneto telephones with all accessories including standard Battery Box and 3 Nos. of 6 I cells as per instructions of the Site Engr. This includes all materials such as heavy duty push button, LED indicator (10mm), MS sheet of 4.5mm thick, nuts and bolts, fixing materials for the magneto telephone including standard Battery Box and 3 Nos. of 6 I cells and wiring materials to be supplied by contractor. (Inspection : RDSO for supply portion and Installation by Site Engineer)
6
19180
115082.28
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%