National Highways Authority Of India Tender

Supply and erection of Galvanized Steel Octagonal Pole (Sheet thickness 3mm) designed to withstand wind speed 169km/hour of suitable length (Raw material confiming to IS-5986 (FE-510), BSEN-10025S-355J or ASTM-572A (GR-50)) and thickness of galvanization (70mm thick) conforming toIS:2629/ IS:2633/ IS:4759, BSEN-ISO-1461-1991 OR ASTM-A123/A123M-02. The pole shall be in single piece hot dip galvanized and shall be tapered towards the top. The bottom section shall have openable slot with exterior surface door & shall have suitable locking arrangement for housing three phase 4wire cable connection, bakelite sheet, MCB, loop in and out arrangment for incoming/ outgoing cables. There shall be suitable arrangement for earthing. Rigid Base plate of suitable size and thickness shall be welded inside and outside at the bottom of pole with provision for fixing 4 foundation bolts. The octagonal pole shall be bolted on a pre- cast foundation with a set of four foundation bolts for greater rigidity. The foundation shall be erected over cement concrete M20 with steel of given size as per design of original pole manufacturer to fixed up to a required planting depth below ground level as required:-Galvanized Octagonal Pole Overall Length 10 metre (Sheet thickness 3mm), Top dia.(A/F) 70mm and bottom dia. (A/F) 175mm, Foundation size below G/L 600mm x 600mm x 1800mm, 4Nos. Foundation Bolts size 24mm dia., Length≥750mm with Base Plate Dimensions 275mm x 275mm x16mm Thick including foundation and other civil work in all respect along with two way bracket and earthing work in all respect.. The pole if at all required will be changed as per the satifaction of Engineer in Charge. (

Dismantling and Supply & erection of Minimum 250 Watt Street Light, System Efficacy greater than equal to 135 LPW, CCT, 5700K , CRI70,SDCM5,Power Factor 0.95,THD10%,Safe Operating Voltage- 140-270V AC,Driver Type- Constant current, Integral, Isolated driver,Built in Surge Protection- 4KV + External 10KV,IP66 & IK07,Toughened Glass with UV Resistant, IK 07 Impact safe glass,Type II lens used for better distribution,Individual lens design is used to reduce light loss due to interference and increase overall distribution.Make - Panasonic , Philips(Signify), Ligthing Technology, Trilux, Wipro, Havells, Surya,Bajaj.The LED Fixture Driver Should have following features:Serviceable, Constant Current, Isolated DriverShort-Circuit, Reverse Polarity & Over Voltage protection in Driver. Helps better reliability of the product.Driver can withstand high voltage up to 440V AC for 8 hrs.LED driver efficiency 85%.Design life of the components 5 years isolated Driver design to separate input & output section to provide rugged surge reliability.The Housing of Luminare Shold have below features: Non-corrosive high-pressure die-cast aluminum to with stand extreme environments. It has corrosion resistant powder coating with . Pressure die cast aluminum housing with aerodynamic heat sink designed for better Heat Dissipation to maintain the Junction temp of LED below Threshold. 105 Deg.Separate Physical compartment for LED and Driver compartment - for ease of maintenance Silicone gasket is used of optimum shore hardness in order to give guaranteed IP Protection.Flexible Mounting design in order to accommodate varied diameter of pipes. B)Earthing to be done , wiring to be changed as per site requirement at actuals and as per approval of Engineer in Charge. Lux Required Uniform 40 (min) Lux.

Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:-

Double Walled Corrugated HDPE Pipe 50/38mm (Outer/ Inner dia.)

Double Walled Corrugated HDPE Pipe 63/51mm (Outer/ Inner dia.)

Supply & Erection/Replacement of Fautly cable (as per site Condition) undergroung, loose in pipe or trenches which has to be don in all respect upto up to the entire satisfaction of Engineer-in-Charge of the work.

16 Sqmm. 4 Core cable (Armoured)

25 Sqmm. 4 Core cable (Armoured)

Recovery of the old material removed per new fixture.

Total Estimated Cost

Bidder to quote single rate as tender premium % above or discount below the total estimated cost mentioned above.

I/We hereby agree to execute the above work on the tender premium or discount quoted here on the total estimated cost mentioned above. I/we understand that filling of both cells meant for premium or discount at a time will render my/our bid as non responsive.

Bid price in Rs.