Military Engineer Services Tender

M&L in replacement power contactor 415 volt, 50 cycles, 3 phase, type ML-4 complete all as specified and as directed by Engineer-in-charge.

M&L in replacement power contactor 415 volt, 50 cycles, 3 phase, type ML-3 complete all as specified and as directed by Engineer-in-charge.

M&L in replacement power contactor 415 volt, 50 cycles, 3 phase, type MNX-80 complete all as specified and as directed by Engineer-in-charge.

M&L in replacement power contactor 415 volt, 50 cycles, 3 phase, type MNX-70 complete all as specified and as directed by Engineer-in-charge.

M&L in replacement power contactor 415 volt, 50 cycles, 3 phase, type AX-18-30-10 complete all as specified and as directed by Engineer-in-charge.

M&L in replacement power contactor 415 volt, 50 cycles, 3 phase, type AX-40-30-10 complete all as specified and as directed by Engineer-in-charge.

M&L in replacement power contactor 415 volt, 50 cycles, 3 phase, type AX-65-30-10 complete all as specified and as directed by Engineer-in-charge.

M&L in replacement power contactor 415 volt, 50 cycles, 3 phase, type AX-80-30-11 complete all as specified and as directed by Engineer-in-charge.

M&L in replacement power contactor 415 volt, 50 cycles, 3 phase, type AX-95-30-11 complete all as specified and as directed by Engineer-in-charge.

M&L in replacement power contactor 415 volt, 50 cycles, 3 phase, type AX-115-30-11 complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement add on auxiliary contact block for MDX/ MNX/AX type contactor range 9-110 / 9- 80 complete all as specified and as directed by Engineer-in-charge Make :–L&T / ABB/BCH/Simens

M&L in replacement bimetal over load relay single phase protection directly mounted 28 to 42 Amps, range ML2/ML3 complete all as specified and as directed by Engineer-in-charge.

M&L in replacement bimetal over load relay single phase protection directly mounted 66 to 110 Amps, range MN5 complete all as specified and as directed by Engineer-in-charge

M&Lin replacement bimetal over load relay single phase protection directly mounted 45 to 75 Amps, range MN5 complete all as specified and as directed by Engineer-in-charge.

M&L in replacement electronic timer (time delay relay) of range 12-120 sec, input voltage 220 to 240 volts AC complete all as specified and as directed by Engineer-in-charge

M&L in replacement single phase preventor, type VSP-2/3 suitable for 3 phase star delta starter of any capacity complete all as specified and as directed by Engineer-in-charge.

M&L in replacement three phase VAF meter of size 96x96x80mm, flush mounting on panel 0 to 500 Volts, Acc class 1.0 digital type, with built in selector switch complete all as specified and as directed by Engineer-in-charge.

M&L in replacement MCCB, 250 Amp, 4 pole ,415 Volts, FP, 50 cycle, breaking capacity 36 KA, thermal magnetic release with two set of copper spreaders complete all as specified and as directed by Engineer-in-charge.

M&L in replacement MCCB, 200 Amp, 4 pole ,415 Volts, FP, 50 cycle, breaking capacity 36 KA, thermal magnetic release with two set of copper spreaders complete all as specified and as directed by Engineer-in-charge.

M&L in replacement MCCB, 160 Amp, 3 pole ,415 Volts, TP, 50 cycle, breaking capacity 25 KA, thermal magnetic release two set of copper complete all as specified and as directed by Engineer-in-charge.

M&L in replacement MCCB, 125 Amp, 3 pole ,415 Volts, TP, 50 cycle, breaking capacity 25 KA, thermal magnetic release two set of copper complete all as specified and as directed by Engineer-in-charge.

M&L in replacement MCCB, 100 Amp, 3 pole ,415 Volts, TP, 50 cycle, breaking capacity 25 KA, thermal magnetic release two set of copper complete all as specified and as directed by Engineer-in-charge.

M&L in replacement MCCB, 63 Amp, 3 pole ,415 Volts, TP, 50 cycle, breaking capacity 25 KA, thermal magnetic release two set of copper complete all as specified and as directed by Engineer-in-charge.

M&L in replacement direct on line (DOL) starter in sheet metal enclosure type, 415 Volt, 3 Phase, suitable for and upto 10 HP electric motor complete all as specified and as directed by Engineer-in-charge.

M&L in replacement direct on line (DOL) starter in sheet metal enclosure type, 415 Volt, MK-1 suitable for and upto 5 HP electric motor complete all as specified and as directed by Engineer-in-charge.

M&L in replacement Flat 6 sqmm three core PVC insulated and PVC sheathed industrial cable for submersible pumps,1100 volts grade, in existing lowering pipe and clamps nut bolts etc and making connections with motor and starter complete all as specified and as directed by Engineer-in-charge.

M&L in replacement Flat 10 sqmm three core PVC insulated and PVC sheathed industrial cable for submersible pumps, 1100 volts grade, in existing lowering pipe and clamps nut bolts etc and making connections with motor and starter complete all as specified and as directed by Engineer-in-charge.

M&L in replacement 25 sqmm three core HRFR PVC 1100 V confirming to IS:694 insulated industrial grade copper conductor (sheathed) flexible cable including copper thimble replacment complete all as specified and as directed by Engineer-in-charge.

M&L in replacement 50 sqmm three core HRFR PVC 1100 V confirming to IS:694 insulated industrial grade copper conductor (sheathed) flexible cable including copper thimble replacment complete all as specified and as directed by Engineer-in-charge.

M&L in replacement 35 sqmm three core HRFR PVC 1100 V confirming to IS:694 insulated industrial grade copper conductor (sheathed) flexible cable including copper thimble replacment complete all as specified and as directed by Engineer-in-charge.

M&L in replacement 16 sqmm three core HRFR PVC 1100 V confirming to IS:694 insulated industrial grade copper conductor (sheathed) flexible cable including copper thimble replacment complete all as specified and as directed by Engineer-in-charge.

M&L in replacement 4 sqmm four core HRFR PVC 1100 V confirming to IS:694 insulated industrial grade copper conductor (sheathed) flexible cable including copper thimble replacment complete all as specified and as directed by Engineer-in-charge.

M&L in replacement flexible spare tyre coupling of any size TC 13 including alignment of pump and motor complete all as specified and as directed by Engr-in-charge.

M&L in replacement flexible spare tyre coupling of any size TC 14 including alignment of pump and motor complete all as specified and as directed by Engr-in-charge.

M&L in replacement flexible spare tyre coupling of any size TC 15 including alignment of pump and motor complete all as specified and as directed by Engr-in-charge.

M&L in replacement flexible spare tyre coupling of any size TC 16 including alignment of pump and motor complete all as specified and as directed by Engr-in-charge.

M&L in replacement flexible spare tyre coupling of any size TC 17 including alignment of pump and motor complete all as specified and as directed by Engr-in-charge.

M&L in replacement flexible spare tyre coupling of any size TC 18 including alignment of pump and motor complete all as specified and as directed by Engr-in-charge.

M&L in replacement flexible spare tyre coupling of any size TC 19 including alignment of pump and motor complete all as specified and as directed by Engr-in-charge.

Material & labour for painting of existing pumpset (with electric motor) and foundation of capacity 60 HP to 120 HP with spray paint carefully as per approved complete all as specified and directed by Engr-in-charge.

Material & labour for painting of existing pumpset (with electric motor) and foundation of capacity 15 HP to 50 HP with spray paint carefully as per approved complete all as specified and directed by Engr-in-charge.

Labour for taking out CI foot valve/Non return valve of any size from jack well approximate 3 mtr deep and refixing the same in original positions after fixing leather buffalow complete all as required at site Note - Rate of leather buffalow /nut bolts and rubber sheet will be included in this item .

Supply only of imeressed graphite gland packing off sizes of superior quality as directed

Supply, fabricating, installation, testing , commissioning in replacement and Electrically connecting LT panel Board ,415 volts ,factory made , machine pressed , dust and vermin proof , cubical type , Indoor type made with 2.0 mm thick CRCA sheet , LT Panel internally and externally shall be painted with epoxy powder coating paint for treatment of degreasing, pickling & two coats primer, before being given the stove epoxy finish , both side opening in two halves with rubber beading , including Bus Bar chamber with aluminium bus bar of 250 Amp capacity , 4 strip mounted on porcelain insulator , bus bar chamber and shall be provided with inspection covers , Each MCCB / Cubical switch shall have be indipendent opening panel shall be mounted with angle iron frame and four legs ( length of one leg 50 cm each ) made from angle iron of size 50mm x 50mm x 6mm frame duly spray painted with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer , embeding and grouting in PCC 1:2:4 type B:1 20 mm graded crushed stone aggregate foundation including necessay earth work complete , including all connections / control wiring incoming / outgoing with suitable size of PVC insulated copper conductor cable of 1100 / 650 vot grade ,Necessary spares such as glands, thimbles , lugs, nuts, bolts etc comprising of following accessories including testing complete all as specified and directed by Engineer-in-charge . Location:- 2EW BGDE PUMP HOUSE (a) MCCB 4 Pole cap-125 Amps, 415 volts, 25 kA (Ics=100% of Icu) with adjustable thermal release 0.7 to 1.0 & fixed magnetic type suitable for 10.0 In - 01 Nos (b) MCCB 3 Pole cap-63 Amps, 415 volts, 25 kA (Ics=100% of Icu) with adjustable thermal release 0.7 to 1.0 & fixed magnetic type suitable for 10.0 In - 03 Nos (c) Automatic star delta starter, 3 Phase suitable for 12.5 HP motor -03 Nos (d) Single phase preventor - 3 Nos. (e) Indicator lamp LED type (set of 3) (f) Digital type voltmeter (suitabe capacity) with selector switch -04 Nos (g) Digital type ammeter with CTs and selector switch of suitable capacity -04 Nos (h) Control MCB SP 6 AMP - 05 Nos (h) Compact Motor Protection Relay-MM10-03 NOS (j) Phase sequence indicator -03 Nos Note:- (i) Necessary excavation and earthwork inclusive of quoted rates. (ii) Makiing good distrubed surfaces inclusive of quoted rates. (iii) Necessary spares such as glands, lugs, nuts, bolts etc deemed to be inclusive of quoted rates. (iv) All outgoing feeder shall be connected to suitable size of bus baar

Supply, fabricating, installation, testing , commissioning in replacement and Electrically connecting LT panel Board ,415 volts ,factory made , machine pressed , dust and vermin proof , cubical type , Indoor type made with 2.0 mm thick CRCA sheet , LT Panel internally and externally shall be painted with epoxy powder coating paint for treatment of degreasing, pickling & two coats primer, before being given the stove epoxy finish , both side opening in two halves with rubber beading , including Bus Bar chamber with aluminium bus bar of 250 Amp capacity , 4 strip mounted on porcelain insulator , bus bar chamber and shall be provided with inspection covers , Each MCCB / Cubical switch shall have be indipendent opening panel shall be mounted with angle iron frame and four legs ( length of one leg 50 cm each ) made from angle iron of size 50mm x 50mm x 6mm frame duly spray painted with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer , embeding and grouting in PCC 1:2:4 type B:1 20 mm graded crushed stone aggregate foundation including necessay earth work complete , including all connections / control wiring incoming / outgoing with suitable size of PVC insulated copper conductor cable of 1100 / 650 vot grade ,Necessary spares such as glands, thimbles , lugs, nuts, bolts etc comprising of following accessories including testing complete all as specified and directed by Engineer-in-charge . Location:-HQ 10 CORE PUMP HOUSE (a) MCCB 4 Pole cap-100 Amps, 415 volts, 25 kA (Ics=100% of Icu) with adjustable thermal release 0.7 to 1.0 & fixed magnetic type suitable for 10.0 In - 01 Nos (b) MCCB 3 Pole cap-40 Amps, 415 volts, 25 kA (Ics=100% of Icu) with adjustable thermal release 0.7 to 1.0 & fixed magnetic type suitable for 10.0 In - 03 Nos (c) Automatic DOL starter, 3 Phase suitable for 7.5 HP motor -03 Nos (d) Single phase preventor - 3 Nos. (e) Indicator lamp LED type (set of 3) (f) Digital type voltmeter (suitabe capacity) with selector switch -04 Nos (g) Digital type ammeter with CTs and selector switch of suitable capacity -04 Nos (h) Control MCB SP 6 AMP - 05 Nos (h) Compact Motor Protection Relay-MM10-03 NOS (j) Phase sequence indicator -03 Nos Note:- (i) Necessary excavation and earthwork inclusive of quoted rates. (ii) Makiing good distrubed surfaces inclusive of quoted rates. (iii) Necessary spares such as glands, lugs, nuts, bolts etc deemed to be inclusive of quoted rates. (iv) All outgoing feeder shall be connected to suitable size of bus baar

Supply, fabricating, installation, testing , commissioning in replacement and Electrically connecting LT panel Board ,415 volts ,factory made , machine pressed , dust and vermin proof , cubical type , Indoor type made with 2.0 mm thick CRCA sheet , LT Panel internally and externally shall be painted with epoxy powder coating paint for treatment of degreasing, pickling & two coats primer, before being given the stove epoxy finish , both side opening in two halves with rubber beading , including Bus Bar chamber with aluminium bus bar of 400 Amp capacity , 4 strip mounted on porcelain insulator , bus bar chamber and shall be provided with inspection covers , Each MCCB / Cubical switch shall have be indipendent opening panel shall be mounted with angle iron frame and four legs ( length of one leg 100 cm each ) made from angle iron of size 50mm x 50mm x 6mm frame duly spray painted with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer , embeding and grouting in PCC 1:2:4 type B:1 20 mm graded crushed stone aggregate foundation including necessay earth work complete , including all connections / control wiring incoming / outgoing with suitable size of PVC insulated copper conductor cable of 1100 / 650 vot grade ,Necessary spares such as glands, thimbles , lugs, nuts, bolts etc comprising of following accessories including testing complete all as specified and directed by Engineer-in-charge . Location:-GOLF COURSE PUMP HOUSE (a) MCCB 4 Pole cap-250 Amps, 415 volts, 36 kA (Ics=100% of Icu) with adjustable thermal release 0.7 to 1.0 & fixed magnetic type suitable for 10.0 In - 01 Nos (b) MCCB 3 Pole cap-160 Amps, 415 volts, 36 kA (Ics=100% of Icu) with adjustable thermal release 0.7 to 1.0 & fixed magnetic type suitable for 10.0 In - 03 Nos (c) Automatic Star Delta Starter , 3 Phase suitable for 50 HP motor -03 Nos (d) Single phase preventor - 3 Nos. (e) Indicator lamp LED type (set of 3) (f) Digital type voltmeter (suitabe capacity) with selector switch -04 Nos (g) Digital type ammeter with CTs and selector switch of suitable capacity -04 Nos (h) Control MCB SP 6 AMP - 05 Nos (h) Compact Motor Protection Relay-MM10-03 NOS (j) Phase sequence indicator -03 Nos Note:- (i) Necessary excavation and earthwork inclusive of quoted rates. (ii) Makiing good distrubed surfaces inclusive of quoted rates. (iii) Necessary spares such as glands, lugs, nuts, bolts etc deemed to be inclusive of quoted rates. (iv) All outgoing feeder shall be connected to suitable size of bus baar

Supply, fabricating, installation, testing , commissioning in replacement and Electrically connecting LT panel Board ,415 volts ,factory made , machine pressed , dust and vermin proof , cubical type , Indoor type made with 2.0 mm thick CRCA sheet , LT Panel internally and externally shall be painted with epoxy powder coating paint for treatment of degreasing, pickling & two coats primer, before being given the stove epoxy finish , both side opening in two halves with rubber beading , including Bus Bar chamber with aluminium bus bar of 400 Amp capacity , 4 strip mounted on porcelain insulator , bus bar chamber and shall be provided with inspection covers , Each MCCB / Cubical switch shall have be indipendent opening panel shall be mounted with angle iron frame and four legs ( length of one leg 100 cm each ) made from angle iron of size 50mm x 50mm x 6mm frame duly spray painted with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer , embeding and grouting in PCC 1:2:4 type B:1 20 mm graded crushed stone aggregate foundation including necessay earth work complete , including all connections / control wiring incoming / outgoing with suitable size of PVC insulated copper conductor cable of 1100 / 650 vot grade ,Necessary spares such as glands, thimbles , lugs, nuts, bolts etc comprising of following accessories including testing complete all as specified and directed by Engineer-in-charge . Location:-PUMP HOUSE NO 12,JADUNATH PUMP HOUSE ,RANJIT PUMP HOUSE (a) MCCB 4 Pole cap-250 Amps, 415 volts, 36 kA (Ics=100% of Icu) with adjustable thermal release 0.7 to 1.0 & fixed magnetic type suitable for 10.0 In - 01 Nos (b) MCCB 3 Pole cap-160 Amps, 415 volts, 36 kA (Ics=100% of Icu) with adjustable thermal release 0.7 to 1.0 & fixed magnetic type suitable for 10.0 In - 03 Nos (c) Automatic Star Delta Starter , 3 Phase suitable for 60 HP motor -03 Nos (d) Single phase preventor - 3 Nos. (e) Indicator lamp LED type (set of 3) (f) Digital type voltmeter (suitabe capacity) with selector switch -04 Nos (g) Digital type ammeter with CTs and selector switch of suitable capacity -04 Nos (h) Control MCB SP 6 AMP - 05 Nos (h) Compact Motor Protection Relay-MM10-03 NOS (j) Phase sequence indicator -03 Nos Note:- (i) Necessary excavation and earthwork inclusive of quoted rates. (ii) Makiing good distrubed surfaces inclusive of quoted rates. (iii) Necessary spares such as glands, lugs, nuts, bolts etc deemed to be inclusive of quoted rates. (iv) All outgoing feeder shall be connected to suitable size of bus baar

Supply, fabricating, installation, testing , commissioning in replacement and Electrically connecting LT panel Board ,415 volts ,factory made , machine pressed , dust and vermin proof , cubical type , Indoor type made with 2.0 mm thick CRCA sheet , LT Panel internally and externally shall be painted with epoxy powder coating paint for treatment of degreasing, pickling & two coats primer, before being given the stove epoxy finish , both side opening in two halves with rubber beading , including Bus Bar chamber with aluminium bus bar of 600 Amp capacity , 4 strip mounted on porcelain insulator , bus bar chamber and shall be provided with inspection covers , Each MCCB / Cubical switch shall have be indipendent opening panel shall be mounted with angle iron frame and four legs ( length of one leg 100 cm each ) made from angle iron of size 50mm x 50mm x 6mm frame duly spray painted with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer , embeding and grouting in PCC 1:2:4 type B:1 20 mm graded crushed stone aggregate foundation including necessay earth work complete , including all connections / control wiring incoming / outgoing with suitable size of PVC insulated copper conductor cable of 1100 / 650 vot grade ,Necessary spares such as glands, thimbles , lugs, nuts, bolts etc comprising of following accessories including testing complete all as specified and directed by Engineer-in-charge . Location:-PUMP HOUSE NO 05 (a) MCCB 4 Pole cap-400 Amps, 415 volts, 36 kA (Ics=100% of Icu) with adjustable thermal release 0.7 to 1.0 & fixed magnetic type suitable for 10.0 In - 01 Nos (b) MCCB 3 Pole cap-200 Amps, 415 volts, 36 kA (Ics=100% of Icu) with adjustable thermal release 0.7 to 1.0 & fixed magnetic type suitable for 10.0 In - 04 Nos (c) Automatic Star Delta Starter , 3 Phase suitable for 75 HP motor -04 Nos (d) Single phase preventor - 4 Nos. (e) Indicator lamp LED type (set of 3) (f) Digital type voltmeter (suitabe capacity) with selector switch -04 Nos (g) Digital type ammeter with CTs and selector switch of suitable capacity -04 Nos (h) Control MCB SP 6 AMP - 05 Nos (h) Compact Motor Protection Relay-MM10-04 NOS (j) Phase sequence indicator -04 Nos Note:- (i) Necessary excavation and earthwork inclusive of quoted rates. (ii) Makiing good distrubed surfaces inclusive of quoted rates. (iii) Necessary spares such as glands, lugs, nuts, bolts etc deemed to be inclusive of quoted rates. (iv) All outgoing feeder shall be connected to suitable size of bus baar

Supply, fabricating, installation, testing , commissioning in replacement and Electrically connecting LT panel Board ,415 volts ,factory made , machine pressed , dust and vermin proof , cubical type , Indoor type made with 2.0 mm thick CRCA sheet , LT Panel internally and externally shall be painted with epoxy powder coating paint for treatment of degreasing, pickling & two coats primer, before being given the stove epoxy finish , both side opening in two halves with rubber beading , including Bus Bar chamber with aluminium bus bar of 400 Amp capacity , 4 strip mounted on porcelain insulator , bus bar chamber and shall be provided with inspection covers , Each MCCB / Cubical switch shall have be indipendent opening panel shall be mounted with angle iron frame and four legs ( length of one leg 100 cm each ) made from angle iron of size 50mm x 50mm x 6mm frame duly spray painted with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer , embeding and grouting in PCC 1:2:4 type B:1 20 mm graded crushed stone aggregate foundation including necessay earth work complete , including all connections / control wiring incoming / outgoing with suitable size of PVC insulated copper conductor cable of 1100 / 650 vot grade ,Necessary spares such as glands, thimbles , lugs, nuts, bolts etc comprising of following accessories including testing complete all as specified and directed by Engineer-in-charge . Location:-36FAD PUMP HOUSE BOREWELL (a) MCCB 4 Pole cap-200 Amps, 415 volts, 36 kA (Ics=100% of Icu) with adjustable thermal release 0.7 to 1.0 & fixed magnetic type suitable for 10.0 In - 01 Nos (b) MCCB 3 Pole cap-100 Amps, 415 volts, 36 kA (Ics=100% of Icu) with adjustable thermal release 0.7 to 1.0 & fixed magnetic type suitable for 10.0 In - 03 Nos (c) Automatic Star Delta Starter , 3 Phase suitable for 30 HP motor -03 Nos (d) Single phase preventor - 3 Nos. (e) Indicator lamp LED type (set of 3) (f) Digital type voltmeter (suitabe capacity) with selector switch -04 Nos (g) Digital type ammeter with CTs and selector switch of suitable capacity -04 Nos (h) Control MCB SP 6 AMP - 05 Nos (h) Compact Motor Protection Relay-MM10-03 NOS (j) Phase sequence indicator -03 Nos Note:- (i) Necessary excavation and earthwork inclusive of quoted rates. (ii) Makiing good distrubed surfaces inclusive of quoted rates. (iii) Necessary spares such as glands, lugs, nuts, bolts etc deemed to be inclusive of quoted rates. (iv) All outgoing feeder shall be connected to suitable size of bus baar

M & L in repair for earthing with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm buried directly in ground ( earth pit not less than 2.25 m deep below normal ground level), with top edge of the plate vertically to depth of not less than 1.5 m below normal ground level connected to and incl GI WIRE 4 mm and GI pipe 15 mm dia light grade for protection to the extent of 7.5 m as earthing lead by means of GI bolts and nuts etc connecting to equipment with provn of charcoal and salt etc all as per electrical plate No 3 of SSR Pt-I incl PCC cover and , watering arrangement with GI pipe 20 mm dia and MS funnel, concrete pit incl excavation and earth work in any type of soil and testing on completion etc complete( Note : PCC chamber shall be constructed at least 1.5m away from earth pit pipe for watering shall be provided in slanting manner.)

M & L in repair for earthing with galvanised steel earth plate electrode 60 cm x 60 cm x 6mm buried directly in ground ( earth pit not less than 2.25 m deep below normal ground level), with top edge of the plate vertically to depth of not less than 1.5 m below normal ground level connected to and incl GI strip 25X4 mm and GI pipe 32 mm dia light grade for protection to the extent of 7.5 m as earthing lead by means of GI bolts and nuts etc connecting to equipment with provn of charcoal and salt etc all as per electrical plate No 3 of SSR Pt-I incl PCC cover and , watering arrangement with GI pipe 20 mm dia and MS funnel, concrete pit incl excavation and earth work in any type of soil and testing on completion etc complete( Note : PCC chamber shall be constructed at least 1.5m away from earth pit pipe for watering shall be provided in slanting manner.)

S&F in replacement of motor protection relay MM10 with suitable size of CTs and control wiring as directed

Material and labour for rectifying the electrical fault of electric motor and LT panels at various pump houses including replacement of copper lugs ,cleaning of LT panel , servicing of power contactors ,and LT panel including copper and alluminium lugs replacement ,rewiring of burnt wiring , servicing of star delta starter as directed .

THE CONTRACTOR SHALL DEPOSITED THE ALL OLD U/S MATERIALS TO AGE E/M W/S STORE YARD BY HIS OWN ARRANGEMENT WITHOUT ANY FINANCIAL BENEFIT RATES TO BE INCLUDED IN QUOTED RATES.