Military Engineer Services Tender
If you want to inquire about any e-tender the Punjab government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder you will find every eprocurement Punjab tender on BidAssist.There is no need to enter all the details on the website of etender.up.nic.in as BidAssist helps you find the specific Punjab etender you're looking for. Read further to learn how to search and bid for etender Punjab.
Costs
EMD
₹ 99,300Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_684133_1Tender No
802024/GE-61/E8Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
Removing excavated soil not exceeding 50 meter and depositing where directed at a level not exceeding 1.50 meter above the starting point complete all as specified and directed.
258.59
-
-
Demolition and breaking up salt glazed stoneware (SGSW) drain pipes set in cement mortar internal dia of pipe 150mm complete all as specified and directed.
765
-
-
Demolition and breaking up salt glazed stoneware (SGSW) drain pipes set in cement mortar internal dia of pipe 200mm complete all as specified and directed.
350
-
-
Demolition and breaking up salt glazed stoneware (SGSW) drain pipes set in cement mortar internal dia of pipe 250mm complete all as specified and directed.
200
-
-
M&L cement concrete 1:3:6, type C2 as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid & tested for 150 mm bore pipe complete all as specified and directed.
845
-
-
M&L cement concrete 1:3:6, type C2 as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid & tested for 200 mm bore pipe complete all as specified and directed.
350
-
-
M&L cement concrete 1:3:6, type C2 as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid & tested for 250 mm bore pipe complete all as specified and directed.
200
-
-
M&L 150mm dia reinforced concrete pipes, class NP2 laid and jointed with collars in trenches complete all as specified and directed.
865
-
-
M&L 200mm dia reinforced concrete pipes, class NP2 laid and jointed with collars in trenches complete all as specified and directed.
350
-
-
M&L 250mm dia reinforced concrete pipes, class NP2 laid and jointed with collars in trenches complete all as specified and directed.
200
-
-
M&L cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for & forming branch channel (1/2 round or ¾ section) in cement concrete 1:2:4, type B1 smooth finished and reforming branching as required for 150 mm dia pipes complete all as specified and directed.
29
-
-
M&L 15 mm thick rendering in cement mortar 1:4 inside and outside wall of manhole of brick work/ concrete surface using WPC as per manufactures instructions complete all as specified and direcetd. Notes: (i) WPC shall be measured and paid for separately as 'Supply only'.
(ii) WPC to be mixed @200ml per 50 Kg bag of cement or as per manufacturers instruction.
1613.46
-
-
Supply only Liquid water proofing compound.
25
-
-
Demolition of cement concrete of any description and in any position not otherwise specifically provided for any thickness complete all as specified and directed.
22.5
-
-
M&L PCC 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation filling, mass concrete, sub base for floors etc. complete all as specified and directed.
30.65
-
-
M&L cement concrete 1:2:4, type B2 (using 40mm graded stone aggregate) in surface channels and drains complete all as specified and directed
8.5
-
-
M&L providing cement concrete 1:2:4, type B1 (using 20mm graded stone aggregate) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier aps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone wallin), corbels, brackets, etc. (of any section indicated), with plain fair faces,including chamfers, weatherings, throating etc. and setting in cement mortar 1:4 complete with joints to match complete all as specified and directed.
5.6
-
-
Demoletion and breaking up drain pipes 75mm-110mm dia (Salt glazed stoneware, AC, PVC or reinforced concrete) set in cement mortar complete all as specified and directed.
650
-
-
M&L cutting holes in brick walls built in cement morter exceeding half brick but not exceeding full brick wall for taking out/ inserting of CI/PVC/AC Pipes/ branch pieces of dia not exceeding 110mm / hold fasts etc. complete all as specified and directed.
20
-
-
S&F 110mm dia PVC(SWR) pipes single socketed in any length with rubber ring joints, sealed with adhesive suitable for PVC pipes and fixed to walls complete all as specified and directed.
300
-
-
S&F 110mm dia PVC(SWR) pipes single socketed in any length with rubber ring joints, sealed with adhesive suitable for PVC pipes laid in trenches complete all as specified and directed.
100
-
-
S&F 110mm dia PVC (SWR) bends with access doors any radius complete all as specified and directed.
20
-
-
S&F 110mm dia PVC (SWR) junction single, (single T) equal or uequal provided with access door complete all as specified and directed.
16
-
-
S&F 110mm PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed.
16
-
-
S&F 110mm PVC (SWR) reducers complete all as specified and directed.
14
-
-
S&F 110 mm dia PVC (SWR) vent cowl complete all as specified and directed.
30
-
-
S&F 75mm dia PVC(SWR) pipes single socketed in any length with rubber ring joints, sealed with adhesive suitable for PVC pipes and fixed to walls complete all as specified and directed.
150
-
-
S&F 75mm dia PVC(SWR) pipes single socketed in any length with rubber ring joints, sealed with adhesive suitable for PVC pipes laid in trenches complete all as specified and directed.
100
-
-
S&F 75mm dia PVC (SWR) bends any radius complete all as specified and directed.
30
-
-
S&F 75mm dia PVC (SWR) junction single, (single T) equal or uequal provided with access door complete all as specified and directed.
20
-
-
S&F 75mm PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed.
20
-
-
Dismantling brickwork built in cement mortar of any specification and in any position complete all as specified and directed.
75.65
-
-
M&L brickwork in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified and directed.
195.01
-
-
All as per ser item No. 36 here-in-before but using old serviceable bricks retrieved from dismantling item No. 35 here-in-before including proper cleaning and removal of mortar from old bricks.
11.65
-
-
M&L RCC 1:2:4, type B1 (using 20mm graded stone aggregate) as in precast cover slab, shelves and similar articles and setting in mortar complete with joints to match existing specifications complete all as specified and directed.
28
-
-
S&F deformed or twisted TMT bar of 10mm dia and over cut to length bend to shape required including cranking, hooking at ends and binding with mild steel wire, (anneled) not less than 0.9 mm dia complete all as specified and directed.
2800
-
-
Demolition of unreinforced cement concrete in ground floors and paving not exceeding 15cm thickness below or above ground level complete all as specified and directed.
13.5
-
-
M&L 75mm thick cement concrete 1:4:8, type D-2 (using 40mm graded stone aggregate) as in sub-base of floor topping, complete all as specified and directed.
135
-
-
M&L 100mm thick cement concrete 1:4:8, type D-2, (using 40mm graded stone aggregate) as in sub base and all other similar works complete all as specified and directed.
54
-
-
M&L 50mm thick cement concrete 1:4:8, type D-2 (using 40mm graded stone aggregate) as in sub floors, sub bases, floors and paving etc. complete all as specified and directed.
150
-
-
M&L 100mm thick, cement concrete 1:2:4, type B-2 (using 40mm graded stone aggregate) as in floor topping, surface finished even and smooth without using extra cement complete all as specified and directed.
135
-
-
Cleaning of blockage IWCs / EWC, bathroom / kitchen by cleaning the nahani traps / gully traps and CI / PVC pipe line upto the 1st Manhole. All the mud / sludge / Kitchen waste / plants roots to be cut/ removed and getting out by washing the traps, CI waste pipe throughly by opening the cleaning eyes lids properly. The sludge/ waste received during cleaning process to be removed at a distance not exceeding 100m from the bldg and Bleaching powder to be spread over waste and burred under the soil / Earth complete all as specified and directed.
Note: Cost of earth work shall be deemed included in the quoted rate.
290
-
-
Cleaning and desludging / de-watering of septic tanks /Manholes and soakage well of any depth by using honey sucker followed by mechanical roding followed by hydraulic jet pressure machine etc. as required, upto entire satisfaction of Engr -in- charge and re-fixing the manholes cover to its original position complete all as specified and directed.
100
-
-
M&L formwork to sides of pillars, posts, struts, piers, band and foundation columns and stanchions Square, rectangular surfaces of concrete complete all specified and directed.
11.39
-
-
M&L three coats of white wash on newely plastered wall surfaces including preparation of wall surfaces complete all as specified and directed.
863.46
-
-
S&F mild steel posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc, and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.
388.58
-
-
S&F galvanized 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins etc. complete all as specified and directed.
Note: Each line of wire to be measured.
13.5
-
-
M&L broken glass coping on top of wall in cement mortar 1:3 complete all as specified and directed.
52.25
-
-
M&L anti-rust concertina coil (reinforced punched barbed tape single layer) for fencing work complete all as per following specifications:- (i) Diameter of concertina coil - 600mm dia (before stretch) (ii) Number of turns in concertina - 50 turns (iii) Weight of each coil - 10.5 KG (iv) Coverage per coil - 8 m (v) Centeral core wire - made from high tensile spring steel core wire conforming to IS-4454 duly hot dipped galvanised (conforming to IS-2629) with diameter 2.59 mm + 0.05mm, UTS 145-160 Kg/Sqmm, Zinc coating 250 to 300 Grams/Sqm. (vi) Strip - Electro galvanised steel strip 0.5mm + 0.02mm thick, width 19mm (before wrapping on centeral core wire) conforming to IS-1573, Zinc coating - 120 Gram/Sqm and bituminised dipped, width of barbs 11.5 mm, pitch of baarbs 25.4mm + 0.2mm (vii) Clips - AISI 304-1.5mm thick 'C' & 'U' clips. 'C' special type for fixing coil and RBT wire. 'U' clips special type for joining one coil to another coil and RBT wire to RBT wire joining. (viii) No. of clips - minimum 125 for each coil. (ix) Handle and spikes to be provided as required.
150
-
-
S&F Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails & guides) & hanging; also fastening & fixing complete GDE Fe-290 E - 165
200
-
-
S&F framed work such as grills grating etc. with ends of bars shoulders or riveted, or forged in to spikes, framed guard bars barred iron doors ladders framed balusters walk way railing framework of water cooler stand, angle iron in stair steps, iron gate and similar work conforming to Fe - 290 Gde E-165 complete all as specified and directed.
90
-
-
M&L preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide zink primer on steel surfaces complete all as specified and directed.
33.55
-
-
Surface excavation not exceeding 30 cm deep and average 15 cm deep and getting out in soft/loose soil complete all as specified and directed.
150
-
-
M&L hardcore of stones bricks gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.
18.45
-
-
M&L sand filling under floors or in foundation of required thickness including watering and consolidation complete all as specified and directed.
5.71
-
-
S&F machine pressed precast 60mm thick concrete interlocking paver block (M-35) cement concrete tiles with grey cement and no pigment of approved design & pattern as approved by GE, set over & including 50mm sand cushioning complete all as specified and directed.
Note: Sand cushioning will be measured and paid for seperately.
228.5
-
-
M&L precast cement concrete block 1:2:4, type B-1 (using 20mm graded stone aggregate) set in cement mortar 1:6 including necessary earth work as in kerb stone complete all as specified and directed.
3
-
-
M&L preparation of new concrete surfaces and applying two coats of synthetic enamel paint (ordinary tint) over a coat of primer as in kerbs stones and all other similar works as per approved pattern complete all as specified and directed.
15
-
-
M&L rendering 15mm thick in cement mortar 1:4 on fair faces of brickwork / concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.
40
-
-
M&L RCC 1:3:6, type C1 (using 20mm graded stone aggregate) precast cement concrete cover slab for manhole and similar article with plain face, set in cement mortar 1:4 including formwork complete all as specified and directed.
0.25
-
-
S&F deformed or twisted TMT bar of 8mm dia cut to length bend to shape required including cranking, hooking at ends and binding with mild steel wire, (anneled) not less than 0.9 mm dia complete all as specified and directed.
25
-
-
M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 10mm thick screed bed in cement mortar 1:4 complete including moulding at corners and polishing type complete all as specified and directed.
6
-
-
M&L preparing new surfaces of walls and applying two coats of cement based paint complete all as specified and directed.
40
-
-
Dismantling Asbestos cement (corrugated, semicorrugated, etc) sheets in roof coverings complete all as specified and directed.
65
-
-
S&F Pre-painted galvalume Aluminum zink coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.
65
-
-
Demolition of ceiling boards of any description, and any thickness including cover fillets and framework complete all as specified and directed.
50
-
-
M&L GI framework for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20mm and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approximate 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exceeding1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete all as specified and directed.
50
-
-
M&L fancy designed 6mm thick exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mm X 600mm grid (frame work for ceiling shall be measured and paid separately) fixed to GI frame work in ceiling and all other similar works complete all as specified and directed.
50
-
-
Dismantling structural steel work as in purlins etc. but excluding framed truss complete all as specified and directed.
1
-
-
S&F steel work in tabular trusse including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS 11614-1979 grade St-240 complete all as specified and directed.
300
-
-
M&L brickwork in cement mortar 1:4 using sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls complete all as specified and directed.
70
-
-
Taking down cement plaster any description on brick or stone walls, or RCC walls surfaces etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.
150
-
-
M&L rendering 15mm thick in cement mortar 1:6 on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.
100
-
-
M&L preparation of old plastered surfaces of walls & applying two coats coats of white wash complete all as specified and directed.
50
-
-
Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as specified and directed.
9
-
-
S&F factory made solid PVC door frame of size 50mm X 47mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2010).
40
-
-
S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, S&F in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified and directed. Make: Rajshri or equivalent in approved makes
13.5
-
-
M&L preparation of old painted steel surfaces over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.
5
-
-
S&F 200mm long Aluminium, anodised barrel tower bolts of extruded section, complete all as specified and directed.
18
-
-
S&F 150mm long Aluminium handles, cast type, anodised complete all as specified and directed.
18
-
-
S&F 300mm long Aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast Aluminium alloy complete all as specified and directed.
2
-
-
S&F 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.
27
-
-
Hacking out old broken glass (any thicknesss, size,quality or description) not exceeding 1.50 Sqm from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.
7
-
-
S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm each pane complete with oil putty complete all as specified and directed.
7
-
-
S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples as in repair complete all as specified and directed.
10
-
-
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises, complete all as specified and directed.
205
-
-
M&L non-skid ceramic tiles coloured 7mm to 8mm thick (square/ rectangular), premium quality area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including screed bedding 15mm thick in cement mortar 1:6, complete all as specified and directed.
93
-
-
M&L glazed coloured ceramic tiles 300mmX200mm and 7mm thick on vertical surface of such as skirting, dados and risers to steps etc., including 10mm thick rendering in cement mortar 1:4 on brick or concrete surface finished rough to received dado/ skirting, set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade with cement mortar bedding and removing off the premises complete all as specified and directed.
151.25
-
-
M&L 25mm thick cement concrete 1:2:4, type B-0, (using 12.5mm graded stone aggregate) as in top layer of sunken floors and levelling course in floor etc. complete all as specified and directed.
75
-
-
Taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed.
70
-
-
Taking up or down existing steel water tubing, 20mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed.
40
-
-
S&F 15mm bore, galvanised iron steel water tubing, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed.
50
-
-
S&F 20mm bore, galvanised iron steel water tubing, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed.
30
-
-
Fixing only, after cleaning old steel water tubing, 15 mm dia bore and connections in new or old position using new fittings complete all as specified and directed. Note: Servicable pipes obtained from item 93 shall be reused and cost of new fittings, if required shall deemed inclusive of quoted rates.
20
-
-
Fixing only, after cleaning old steel water tubing, 20 mm dia bore and connections in new or old position using new fittings complete all as specified and directed. Note :- Servicable pipes obtained from item 94 shall be reused and cost of new fittings, if required shall deemed inclusive of quoted rates.
10
-
-
S&F 15mm bore, brass chromium plated bib tap for iron pipe, fancy type with crutch or butterfly handle, screwed down high pressure as in repair complete all as specified and directed.
7
-
-
S&F 15mm bore fancy type chromium plated Stop cock cast Copper alloy screwed down, high pressure screwed both ends for iron pipe or union as fixed in repairs complete all as specified and directed.
23
-
-
S&F 15mm bore pillar tap, cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe as in repair complete all as specified and directed.
7
-
-
S&F 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair complete all as specified and directed.
3
-
-
S&F 15mm bore bib tap standard of PTMT any colour screwed, for iron pipe as in repair complete all as specified and directed.
10
-
-
S&F 32 mm bore PVC waste pipe suitable to waste coupling pipe attached with rubber ring joints fixed to waste coupling of sinks / WHBs complete all as specified and directed.
16
-
-
S&F low density polythene pipe (LDPE) of pressure rating 6 Kg per Sqcm, 450 mm long, heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipe as in repair complete all as specified and directed.
5
-
-
S&F 500 litre capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe as in repair as specified in SSR Part-I complete all as specified and directed.
2
-
-
S&F 1000 litre capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe as in repair as specified in SSR Part-I complete all as specified and directed.
1
-
-
S&F vitreous China wash down water closet pan (pedestal pattern), white/ coloured including seat & cover, flush pipe, trap, connection to drain and to flushing pipe, anti-syphonage pipe, etc. complete all as specified and directed.
7
-
-
S&F vitreous China bowl urinal flat back, of size 465mm X 355mm X 265mm white (minimum), with grating and union for discharge pipe (including flushing cistern, flush pipe and waste pipe) complete all as specified and directed.
14
-
-
S&F PVC 10 litre capacity valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc. complete all as specified and directed.
7
-
-
S&F itreous China wash basin, white/ coloured, flat back, size 550mmX400mm including PTMT waste fittings, 32mm bore size, waste pipe pvc 32mm bore and angle iron brackets of required size and length etc. and making good disturbed surfaces to match with the existing complete all as specified and directed.
7
-
-
S&F PTMT grating doom 100mm dia with or without waste hole fixed in repairs complete all as specified and directed.
18
-
-
S&F 600mmX450mm looking mirror of selected quality glass, mounted on 6mm thick commercial plywood and fixed to wall with plug and screws etc. complete all as specified and directed.
6
-
-
S&F Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed to walls with steel screws and wooden/rawl plugs as in repairs complete all as specified and directed.
3
-
-
M&L PVC (SWR) floor trap 75mm, plain with PVC grating including jointing with solvent cement etc., complete all as specified and directed.
10
-
-
S&F 15mm bore, push tap in any colour of PTMT suitable for urinals screwed for iron pipe and fixed (minimum weight 15mm-50 gms) complete all as specified and directed.
14
-
-
S&F PVC connection 15mm size PTMT nuts of length 450 mm complete all as specified and directed.
20
-
-
M&L 15 mm bore fancy type health faucet with SS hose as in repair complete all as specified and directed.
7
-
-
M&L 50mm thick, PCC 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection, shall be laid in 1:20 slope. The concrete shall be laid at a stretch not exceeding 3-meter in length. Joint gap between the adjoining slab, at corners and at junctions of wall shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen of grade 85/25 garde mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3-meter interval at corner and junction walls complete all as specified and directed.
50
-
-
M&L 75mm thick, PCC 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection, shall be laid in 1:20 slope. The concrete shall be laid at a stretch not exceeding 3-meter in length. Joint gap between the adjoining slab, at corners and at junctions of wall shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen of grade 85/25 garde mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3-meter interval at corner and junction walls complete all as specified and directed.
24
-
-
M&L extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc. as in manhole pipe line portion only complete all as specified and directed.
10
-
-
Dismantling Stone slabs and tiles of any description or thickness in floors, aprons laid bedded ,dry and pointed etc. complete all as specified and directed.
7.85
-
-
Taking down carefully Copper / Aluminium point wiring (light, fan, socket or power) complete, fittings such as switches, ceiling roses, pendants, regulators sockets light fitting etc removing materials to store for keetping in safe custody or for taking credit (credit for taking down items shall be paid for separately) and making good to the disturbed surfaces of walls, floors ,etc. to match with the existing specifications complete all as specified and directed.
9
-
-
M&L point wiring complete with 1100 Volts grade PVC insulated unsheathed FRLS cable of Copper conductor, multi stranded of size 1.5 Sqmm, single core, in and including rigid non-metallic PVC conealed conduit, with all accessories if require such as bends, reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks (for housing lamp holders and light fittings etc) and existing MS pressed steel / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire of size 1.5 Sqmm unsheated stranded Copper conductor with green PVC insulation connected to common earth dolly complete all as specified and directed for the followings :- (a) One light/fan/Bell Point controlled by one single pole one way switch.
9
-
-
(b) One socket outlet on the same board controlled by one single pole one way switch.
1
-
-
(c) One 5 Amps socket outlet independent controlled by one single pole 5 Amps switch.
1
-
-
All as per ser item No. 124 here-in-before but one three pin 15 Amps switch socket out let on the independent board with 2.5 Sqmm PVC insulated Copper conductor and 2.5 Sqmm Copper conductor for continuous earthing complete.
1
-
-
S&F ceiling rose, PVC/Polycarbonate, isolated three terminals complete all as specified and directed.
8
-
-
S&F in replacement Modular Switch one way 6 Amps, 1 module complete all as specified and directed.
11
-
-
S&F in replacement Modular Switch one way 16 Amps, 1 module complete all as specified and directed.
1
-
-
S&F in replacement Modular Socket, 6A - 2/3 pin combined 2 module complete all as specified and directed.
2
-
-
S&F in replacement Modular Socket, 6A/16A - 2/3 pin combined 2 module complete all asper specified and directed.
1
-
-
S&F in replacement Modular white cover plate including GI box inner, 3 module complete all as specified and directed.
2
-
-
S&F in replacement Modular white cover plate including GI box inner, 6 module complete all as specified and directed.
1
-
-
S&F in replacement Modular white cover plate including GI box inner, 8 module complete all as specified and directed.
1
-
-
S&F lamp holder PVC/Polycarbonate, isolated with back plate suitable for batten fittings including 10 Watts LED bulb complete all as specified and directed.
1
-
-
S&F exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230 Volts, 50 Hz, 1200 RPM, Copper winding of sweep 300mm complete all as specified and directed.
2
-
-
S&F LED tube light fitting 1 X 18 Watts decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient 230 Volts, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible Copper conductor cable with suitable size complete all as specified and directed.
Make : Cat Part No LHEXBLP7UN1W018 Make - Havells or techno-commercially equivalent in approved makes
2
-
-
S&F sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 Volts 200 Amps rated bus bar, neutral link, earth bar and Din rail, 4 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified and directed.
1
-
-
S&F MCB, Single pole 240 Volts, 6 Amps to 32 Amps 10 KA 'B Series complete all as specified and directed.
2
-
-
S&F SPN 32 Amps rating 240 Volts, 10KA 'B' curve miniature circuit breaker (MCB) DB complete with connection testing and commissioning complete all specified and directed.
2
-
-
S&F sub main wiring of 6 Sqmm PVC insulated unsheathed FRLS cable multistranded copper conductor with earth wire of 6.0 sqmm PVC insulated unsheathed FRLS cable multistranded copper conductor including PVC conduit pipe 25 mm dia complete all as specified and directed.
Note:-Two run of single core 6 sqmm cable and one run single core 6.0 sqmm cable for earth wire and including conduit pipe 25 mm dia shall measured as one length).
30
-
-
M&L earthing complete with galvanized steel plate elecrode of size 60cm x 60cm and 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5m below the ground level with top edge of earth plate at a depth not less than 1.5 m below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate). The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete 1:2:4, type B-1 (using 20 mm graded stone aggregate), excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50m as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009).
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%