Military Engineer Services Tender
If you want to inquire about any e-tender the Punjab government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder you will find every eprocurement Punjab tender on BidAssist.There is no need to enter all the details on the website of etender.up.nic.in as BidAssist helps you find the specific Punjab etender you're looking for. Read further to learn how to search and bid for etender Punjab.
Technical
Technical
Class Of Bidder
... View More
The class eligibility requirement to bid or participate in this tender is either 'A' class or not explicitly stated. However, since there are multiple sources with varying information, the most consistent and specific answer provided is 'A' class. Therefore, the answer is: Class A.
Technical Capacity
... View More
There is no specific information available on the required prior work experience for the bidder in terms of years. However, it is mentioned that contractors of one class below the eligible class may be considered if they fulfill certain criteria, including past experience of completed works and financial soundness. For un-enlisted contractors, they should meet the enlistment criteria of 'A' class & 'a(i)' category contractor with regard to satisfactorily completion of requisite value works. No specific value or percentage of similar works completed is mentioned, except that un-enlisted contractors should not have a total value of works more than twice the tendering limit of the MES Class of contractor for which it is eligible. Additionally, an un-enlisted contractor who has secured two works in MES should get themselves registered in the appropriate designated class. The contractor should have satisfactorily completed requisite value works with Central/State Government/ Central/ State PSUs/AWHO/AFNHB/CGEWHO/DGMAP, but specific amounts or percentages are not mentioned.
Costs
EMD
₹ 6,15,000Document Cost
₹ 3,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2025_MES_696273_1Tender No
81086/E8Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
M&L Cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in fillings and mass concrete, filling backs of chowkats etc, complete all as specified and directed.
35.36
-
-
... More
M&L for Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in roof kerbs or mud stops, bed blocks,benching etc including necessary form work, complete all as specified and directed.
17.28
-
-
... More
Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level), complete all as specified and directed.
212.14
-
-
... More
M&L Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc, complete all as specified and directed.
3408
-
-
... More
M&L for Cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in plinth protection, 75mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints, complete all as specified and directed.
949
-
-
... More
M&L for 25 mm thick cement concrete (1:2:4) type B-1 using (20 mm graded crushed stone aggregate) as in sub base of flooring,surface finished rough to receive floor topping, complete all as specified and directed.
2394
-
-
... More
M&L Non-skid Ceramic tiles coloured 7 to 8 mm thick (square/ rectangular), premium quality area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and incl screed bedding 15mm thick in cm(1:6) , complete all as specified and directed.
4557
-
-
... More
M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in cement mortar (1:4), , complete all as specified and directed.
616
-
-
... More
M&L for Glazeded ceramic coloured (colour & shade as approved) tile 450x300x7mm thick on vertical surface such as skirting/dados set and jointed in neat cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white/coloured cement with pigment to match the colour of tiles, complete all as specified and directed.
3241
-
-
... More
M&L for Machine cut kota stone slab 18-20 mm thick as in flooring of size not less than 0.25 Square metre each, set and jointed in cement slurry over & including screed bed of 20 mm thick in cement mortar (1:6) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and polishing, complete all as specified and directed.
405
-
-
... More
M&L for 18 to 20 mm thick Baroda green marble in single piece incl nosing at front and sides in steps, jambs,pillars,window cills,cooking platforms,staircase and like with bull nosing in cm(1:4) incl pointing in white cement(1:2) using marble dust with admixture of pigment to match with marble shade including making grooves for slip guard or steps,edge moulding,making 30 mm dia hole in cooking counter slab and green marble top for gas pipe including 15mm thick screed bed in cm 1:4 and providing edge moulding to marble incl machine polishing to edge to finish etc, complete all as specified and directed.
314
-
-
... More
M&L for Machine cut kota stone slab 18-20 mm thick as in skirting,dado of length not less than 500 mm each unit, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and polishing, complete all as specified and directed.
157.8
-
-
... More
M&L for Granite(of any type) tiles18- 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 10 mm thick plaster as in back coat CM 1:4 complete including making circular gas pipe hole, moulding at corners and polishing type, complete all as specified and directed.
305
-
-
... More
Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified and directed.
1000
-
-
... More
Dismantling of brick tiles single layer laid on roof jointed & pointed in cement mortar, complete all as specified and directed.
2860
-
-
... More
Demolition/taking out mud from the roofs, any thickness, including plastering and leaping etc including removing rubbish upto 500 mtr from the site , complete all as specified and directed.
229.2
-
-
... More
M&L for rendering 10 mm thick in CM (1:4) mixed with integral water proofing compound as per mfg instr over the padding concrete while still the concrete is still green, complete all as specified and directed. (For roof treatment)
Note:- WPC will be measured & paid seperately.
2860
-
-
... More
M&L for water proofing treatment to roof surface including parapet wall comprising with the following course of treatment/ specifications form bottom to top:-
(a) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg per sqm over a coat of bitumen primer @ 0.30 ltr per sqm including preparation of roof surfaces complete all as specified and as directed. (b) One layer of APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface
by forced application complete all as specified. Polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of parapet walls and shall be finished by a membrane flashing.
Note:- (i) Laying of APP based membranes shall be done by torch on method or as per manufacturer's instructions.
(ii) A minimum overlap shall be 75mm length wise and 100 mm width wise of polymeric membranes respectively and sealed all overlaps and joints as manufacturer's instructions.
2860
-
-
... More
M&L for two coat of aluminium paint over APP membrane, complete all as specified and directed.
1106
-
-
... More
M&L for cement concrete tiles 25cm x 25cm x 22mm thick laid on roof over 15 mm thick screed in cement mortar (1:4) and joints grouted flush in CM 1:3 mixed with 5% of crude oil by weight of cement, complete all as specified and directed.
1772
-
-
... More
M&L for Cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in roof padding, complete all as specified and directed.
134.72
-
-
... More
Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins,arches,pillars etc, complete all as specified and directed.
33
-
-
... More
M&L brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in c:m 1:6, complete all as specified and directed.
24
-
-
... More
All as per srl item No 25 here-in-before but using old bricks retrieved from dismantling under srl item 24 here-in-before including cleaning and removal of mortar from old bricks etc, complete all as specified and directed.
9
-
-
... More
Taking down cement plaster on brick walls of any description including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.
14767
-
-
... More
M&L for Rendering 12mm thick in cement mortar (1:6) on fair face of brick walls or concrete surfaces, finished fair and even without using extra cement, complete all as specified and directed.
7165
-
-
... More
M&L for Rendering 15mm thick in cement mortar (1:4) on other than face of brick walls or concrete surfaces, finished fair and even without using extra cement using WPC, complete all as specified and directed. Note:- WPC measured and paid separately.
5916
-
-
... More
Supply only integral water proofing compound (WPC) ISI marked, complete all as specified and directed.
2121
-
-
... More
M&L for Rendering 5 mm thick cement plaster on ceiling surfaces in cement mortar 1:3 finished fair and even without using extra cement, complete all as specified and directed.
1887
-
-
... More
M&L for Preparation of new plastered surfaces of ceiling & applying two coats of white wash, complete all as specified and directed.
1806
-
-
... More
M&L for preparation of old surfaces of ceiling and applying one coat of white wash, complete all as specified and directed.
3937
-
-
... More
M&L for 2mm thick wall care putty on wall, complete all as specified and directed.
15989
-
-
... More
M&L Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new plaster surface work complete all as specified.
7165
-
-
... More
M&L for removal of complete existing treatement on wall & Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification, complete all as specified and directed.
11211
-
-
... More
M&L for applying two coats of Acrylic Exterior Emulsion on plaster surface walls including preparation of new plaster surfaces on wall , complete all as specified and directed. Make :- Berger weather coat, Asian apex , Nerolac excel or equivalent
5916
-
-
... More
M&L for preparation of old surfaces of walls & applying two coats of white wash, complete all as specified and directed.
2973
-
-
... More
Taking down existing wall finishes, any type by vigorously wire brushing, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of existing finishes & foreign materials, making good minor surface imperfections such as holes, dents cracks etc in CM 1:3 & applying 02 coats wall putty (Birla putty) on the surface with uniform thickness incorporating Birla putty 2.00mm thick & making surface absolutely smooth on entire satisfaction of Engineer-in-Charge & applying two coats of Acrylic Emulsion white or tinted, complete all as specified and directed. Make :- Berger Rangoli Emulsion, Asian Apcolite Emulsion, Nerolac/ Dulux or equivalent.
3096
-
-
... More
Taking down chowkats or frames with shutters (without taking off shutters from the frame) of size not exceeding 1.5 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts and removing from site to store or otherwise as directed, complete all as specified and directed.
864
-
-
... More
All as per srl item No 40 here-in-before but size exceeding 1.5 Sqm and not exceeding 4 Sqm each , complete all as specified and directed.
816
-
-
... More
Taking down shutters of any description,exc.1.0 sqm and not exc.2 sqm each and after reparing refixing the same, complete all as specified and directed.
88
-
-
... More
S&F Pressed steel frames (1.25mm sheet thickness) for doors with one or more rebates including necessary fixing lugs, hinges, lock plate, etc., size of frame 125mm x 60 mm including one shop coat of red oxide primer, complete all as specified and directed.
1708
-
-
... More
S&F Pressed steel frames (1.25mm sheet thickness) for doors with one or more rebates including necessary fixing lugs, hinges, lock plate, etc., size of frame 105mm x 60 mm including one shop coat of red oxide primer, complete all as specified and directed.
2043
-
-
... More
S&F 30mm thick, Flush shutters, solid core construction, with block board core, commercial type with one face is covered with deco rative face veneer with lipping/frame to match, complete all as specified and directed.
1173.4
-
-
... More
S&F 35 mm thick, 2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, , complete all as specified and directed.
688.4
-
-
... More
S&F Stainless steel plate rack of standard pattern & of size 900 x 750 x 250 mm.The thickness of stainless steel sheet shall be 1.00 mm & grade of sheet shall be 304 AISI including fixing to wall with 4 Nos 50mm screws & PVC rawl plugs, complete all as specified and directed.
104
-
-
... More
S&F steel window powder coated as per IS 13871 ; 1993 of followinf specification of powder coating material :- (a) Grade :-'A' (Glossy finish) (b) Dry flim thickness of 50-60 microns (c) Protection against humidity - No blistering, rusting and loss of adhesion (d) Resistance to heat, detergents and acid/alkai - Np appreciable change of colour (Colour of powder coating as per user direction). The specification of Box type window are 1,25mm thick Box type (primer coated) ERW hollow P section of size 60mm x 25mm Single rebated comprises gauged skelton shutter ERW box type T- section of 50 mm x 20mm and 1mm thick with one or two openable leaf consisting two sash bar of T- section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- section of size 60 mm x 25 mm and 1.25 mm thick including cuttiing holes and making good dismantled portion in PCC (1:3:6) type C-1 four Nos for each window) including following fitting welded to frame shuyyer. (a) Mild steel Hold fast 150mm long of 12mm square bar made to shape - 04 Nos par window (b) Handles of Z sec 20mm x 100 mm long (c) Stopper -01 No per leaf (d) Cleat 55 mm long of hollow square 15mm x 20mm x 63mm welded to hinges -01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges -01 No per leaf (e) Mild steel Pintal hinges of size 75mm x 75mm x 12mm-02 Nos leaf. Note:- Glass and painting shall be measured and paid separetely under appropiate item (ii) Irrespective of whatever shown on drgs, MS grills shall be 12 mm square bar also shall be measured and paid separately.
627
-
-
... More
S&F steel window powder coated as per IS 13871 ; 1993 of followinf specification of powder coating material :- (a) Grade :-'A' (Glossy finish) (b) Dry flim thickness of 50-60 microns (c) Protection against humidity - No blistering , rusting and loss of adhesion (d) Resistance to heat , detergents and acid/alkai - Np appreciable change of colour (Colour of powder coating as per user direction). The specification of Box type window are 1,25mm thick Box type ( primer coated) ERW hollow P section of size 60mm x 25mm Single rebated comprises gauged skelton shutter ERW box type T- section of 50 mm x 20mm and 1mm thick with one or two openable leaf consisting two sash bar of T- section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- section of size 60 mm x 25 mm and 1.25 mm thick including cuttiing holes and making good dismantled portion in PCC (1:3:6) type C-1 four Nos for each window) including following fitting welded to frame shuyyer. (a) Mild steel Hold fast 150mm long of 12mm square bar made to shape - 04 Nos par window (b) Handles of Z sec 20mm x 100 mm long (c) Stopper -01 No per leaf (d) Cleat 55 mm long of hollow square 15mm x 20mm x 63mm welded to hinges -01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges -01 No per leaf (e) Mild steel Pintal hinges of size 75mm x 75mm x 12mm-02 Nos leaf.
Note:- Wiremesh & painting shall be measured and paid separately under appropiate item etc, complete all as specified and directed.
411.64
-
-
... More
S&F Factory made box type steel ventilator with & includingglazing bars dovetailed or welded and with one shop coat of zinc chromate primer, complete all as specified and directed by Engr-in-Charge.
354
-
-
... More
S&F Mild steel framed work of as in grills/guard bars shouldered with steel window/ventilator frames, complete all as specified and directed.
796
-
-
... More
S&F 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm, complete all as specified and directed.
339
-
-
... More
S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.
1296.8
-
-
... More
S&F 4.0 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane fixed to aluminium ventilator, complete all as specified and directed.
94
-
-
... More
S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube, complete all as specified and directed.
983
-
-
... More
S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rail MS frame shall be covered with heat moulded plain/coloured PVC "C"channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed togeather with solvent cement, complete all as specified and directed.
284.72
-
-
... More
S&F factory made PVC cup boards/ Shelf/Partition of required size consisting of panel of 18mm thick Celuka PVC Ply and for supporting the hold of Shelf/Partition and shall provided 3 edges in size 18mm x 18mm as per required length. The front side of the edge visible in the front of the shelf/Partition to be edge lipped by 18mm width x 1mm thick PVC sheet using solvent cement etc, complete all as specified and directed.
572.8
-
-
... More
Dismantling timber in fillets, rails, posts, rafters, purlins, etc; under 40 sq. cm in each section, fixed in any position as in framed work, complete all as specified and directed.
669
-
-
... More
M&L for Plain fillets of 2nd class hard wood, square or rectangular or triangular in section, clean sawn, secured with nails and brads area n exc 3 Sq cm complete all as directed
669
-
-
... More
Mild steel framed work of Fe-290 Gde-E-165 as in doors or gate of angle or other section with gusset plates,rails, braces etc and fixing complete all as specified.
6201
-
-
... More
Dismantling of boarding, any description, fixed in any position with nails, complete all as specified and directed.
637
-
-
... More
S&F 18mm thick Prelaminated particle board,flat pressed single layer type or three layer type with BWR type adhesive, medium density interior grade, prelaminated both side with decorative choice lamination, fixed with screws as in shutters & shelves including 6mm thick teak wood leaping on three sides and 20mm thick on hanging side, complete all as specified and directed.
461
-
-
... More
M&L for Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed.
3018.08
-
-
... More
M&L for Preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of redoxide priming, complete all as specified and directed.
841
-
-
... More
M&L for one coats of synthetic enamel paint including preparation of old painted wood or wood bases surface of any description over 10 cm.width or girth, complete all as specified and directed.
265
-
-
... More
M&L for one coats of synthetic enamel paint, including preparation of old painted steel or steel bases surface of any description over 10 cm width or girth, complete all as specified and directed.
177
-
-
... More
S&F PTMT butt hinges, 100 mm long and fixed with steel screws, complete all as specified and directed.
624
-
-
... More
S&F PTMT tower bolts, 150 mm long and fixed with steel screws, complete all as specified and directed.
416
-
-
... More
S&F PTMT door handle, 150 mm long and fixed with steel screws, complete all as specified and directed.
416
-
-
... More
S&F Aluminium tower bolts 150 mm long & fixed with steel screws, complete all as specified and directed.
2016
-
-
... More
S&F Aluminium bow handle 150 mm long and fixed with steel screws, complete all as specified and directed.
2296
-
-
... More
Continous (piano) hinges of mild steel bright finish or electro galvanised with flap (when open) 30mm, fixed with steel screw, complete all as specified and directed.
574
-
-
... More
S&F alluminium anodised handles 100 mm long fixed to Cupboard etc, complete all as specified and directed.
416
-
-
... More
S&F 100mm long hasp and staple, safety type, aluminium anodised including bolt to hinge plate and fixed with screws and fixed, complete all as specified and directed.
156
-
-
... More
S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.
676
-
-
... More
S&F 150 mm Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, complete all as specified and directed.
868
-
-
... More
S&F 150 mm mild steel ordinary rat tail spring including roller and roller plate, complete all as specified and directed.
256
-
-
... More
S&F 300 mm mild steel ordinary rat tail spring including roller and roller plate, complete all as specified and directed.
128
-
-
... More
M&L for Cutting chases, pinning in. making good to facings where required for brick wall and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed.
1365
-
-
... More
Taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed.
1613
-
-
... More
All as per ser item No 80 here-in-before but 20 mm bore tubing, complete all as specified and directed.
552
-
-
... More
M&L for GI steel water tubing, 15mm bore medium grade galvanized with all fittings and fixed to walls and celling or laid in floor, complete all as specified and directed.
1613
-
-
... More
All as per ser item No 82 here-in-before but 20 mm bore tubing, complete all as specified and directed.
552
-
-
... More
S&F in repair stop valves, fancy type, CP with long shank and cup (concealed type), screwed both ends for 15mm bore of iron pipe or for union and fixed, complete all as specified and directed.
104
-
-
... More
S&F in sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long, complete all as specified and directed.
104
-
-
... More
S&F in repair gun metal gate valve of 20mm dia with iron wheel head screwed both ends for iron pipe, complete all as specified and directed.
232
-
-
... More
S&F in repair bib taps, fancy type CP, screwed for 15mm bore of iron pipe or for brass ferrule and fixed, complete all as specified and directed.
568
-
-
... More
S&F in repair for Brass CP mixer for mixing hot & cold water screwed down for 15mm bore iron pipe and fixed, complete all as specified and directed.
208
-
-
... More
S&F in repair stop valves/angle cock,fancy type cast copper alloy,screwed down, high pressure,with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed, complete all as specified and directed.
376
-
-
... More
S&F Vitreous china wash basin, white/coloured, flat back, size 550 x 400mm including PTMT waste fittings & pipe, 32mm bore size and angle iron brackets & CP Pillar Brass mixer for mixing hot & cold water screwed down for iron pipe and fixed and making good disturbed surfaces to match with the existing, complete all as specified and directed.
28
-
-
... More
S&F Vitreous china wash basin, white/ coloured, flat back, size 450x300mm including PTMT waste fittings & pipe, 32mm bore size and angle iron brackets & CP Pillar Brass mixer for mixing hot & cold water screwed down for iron pipe and fixed and making good disturbed surfaces to match with the existing, complete all as specified and directed.
76
-
-
... More
S&F Low density polyethylene (LDPE) pipes 32mm bore of pressure rating 6 kgf/sqcm, complete all as specified and directed.
144
-
-
... More
S&F in repair PVC connections 15mm size with PTMT nuts of length 450 mm, complete all as specified and directed.
480
-
-
... More
S&F in repair 500 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe incl dismantling existing water storage tank complete all as specified in SSR Part-I , complete all as specified and directed.
104
-
-
... More
S&F in repair Vitreous china squatting pan, Orissa pattern, size 580 x 440mm white/coloured with integral foot rests including trap set in and including concrete and connection to trap, and to flushing pipe, anti-syphonage pipe, etc, complete all as specified and directed.
66
-
-
... More
S&F in repair Vitreous china wash down water closet pan (pedestal pattern including P or S trap), white/coloured including seat & cover, flush pipe,health faucet connection to drain and to flushing pipe, anti-syphonage pipe, etc, complete all as specified and directed.
38
-
-
... More
S&F in repair PVC 10 ltr. Cap. valveless syphonic action type, flushing cictern, low level, white/coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc, complete all as specified and directed.
104
-
-
... More
S&F in repair 125 mm chromium plated shower rose with or without swivel joints any size including fixing to steel pipe or union, complete all as specified and directed.
104
-
-
... More
S&F in repair 600 x 450mm looking mirror of selected quality mounted on 6mm thick commercial plywood and fixed to wall with plug and screws etc, complete all as specified and directed.
104
-
-
... More
S&F in repair Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed to walls with steel screws and wooden/rawl plugs as in repairs, complete all as specified and directed.
104
-
-
... More
S&F Stainless steel soap dish (not less than 1mm thick) of type as directed,fixed to walls with chromium plated brass screws with wooden/rawl plugs, complete all as specified and directed.
104
-
-
... More
S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and astes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm , complete all as specified and directed.
92
-
-
... More
S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm (R), complete all as specified and directed.
28
-
-
... More
Dismantling upto 100mm of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out from wall/trenches, if required, complete all as specified and directed.
64.6
-
-
... More
Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings heads shoes bends swan-necks etc, complete all as specified and directed.
1873
-
-
... More
S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches, complete all as specified and directed.
581
-
-
... More
S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches, complete all as specified and directed.
1260
-
-
... More
S&F 75mm dia PVC (SWR) bends any radius, complete all as specified and directed.
264
-
-
... More
S&F 110 mm dia PVC (SWR) bends any radius, complete all as specified and directed.
264
-
-
... More
S&F 75mm dia Junction single (Single or double T) equal or unequal, complete all as specified and directed.
104
-
-
... More
S&F 110mm dia Junction single (Single or double T) equal or unequal, complete all as specified and directed.
104
-
-
... More
M&L PVC (SWR) floor trap 75 mm, plain with PVC grating including jointing with solvent cement etc, complete all as specified and directed.
312
-
-
... More
S&F Mild steel curtain rod powder coated with fixing side fancy type brackets, end cups,rings @ 10 Nos per running metre and fixed with PVC rawl plugs & steel screws as in repairs, complete all as specified and directed.
1533
-
-
... More
M&L for 15 mm thick rendering over concrete surface of sunken floor in CM 1:3 on wall as well as sunken floor finished even and smooth without using extra cement using WPC, complete all as specified and directed. Note:- WPC measured and paid separetely.
310.2
-
-
... More
M&L for Water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WC's etc shall be as under:-
(i) Application of Two component Acrylic modified Cementitious coating.
(aa) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance, existing coatings and achieve a gripping profile that is clean, dry and free from litanceand and any other form of surface contamination. The installation instructions in manufacturer's published literature should be strictly complied with including but not limited to the following:-
(bb) Chipping out any visible cracks in "V-Groove" pattern as applicable. Special attention on this pa Cleaning of cracks & then filling those cracks with SIKA latex SBR 100 putty/Dr Fixit 302 SBR late Perma latex SBR/FOSROC Nitabond SBR latex/Asian Paints latex as required. Final cleaning surface with power grinder, wire brush, hair brush & vacuum pressure if required. (cc) Dampen all surfaces immediately ahead of application of Acrylic modified Cementitious coatin Sika Top Seal-107/Brush Bond FOSROC/Dr Fixit/STP/CICO.
(dd) Whilst the surface is still damp from saturation (S.S.D), apply one coat of Acrylic mo Cementitious coating of Sika Top Seal-107/Brush Bond FOSROC/Dr Fixit/ STP/CICO of vis as per manufacturer's instructions.
(ee) Apply Glass Fabric Sheet of Sika Fab 1/FOSROC/ Dr Fixit/STP whilst the first coat is wet.
(ff) Once touch dry, apply second coat of Acrylic modified Cementitious coating of Sika Top Sea/Brush Bond FOSROC/Dr Fixit/STP/CICO of viscosity as per manufacturer's instructions entire area.
(gg) Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direc angle to the previous coat.
(hh) The waterproofing coating should be taken to a height minimum 300 mm above the finis level on the vertical surface.
310.2
-
-
... More
(jj) It is essential to cure Acrylic modified Cementitious coating immediately after application 3-8 Hrs drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize.
(kk) A protection plaster (12-15mm thick) in CM 1:3 admixed with appropriate Integral wa Compound has to be applied on the walls. Admixture :- Sika plastocrete plus/FOSROC/Dr Fixit/STP/CICO confirming to IS 2645.
(ll) Providing and applying a protection screed of 50 mm thick 1:4 cement sand mortar admixed with Sika plastocrtete over applied water proffing coating on horizontal surface.Admixture :- Sika plastocrete plus/FOSROC/Dr Fixit/STP/CICO confirming to IS 2645.
(mm) All the corners and joints should be pretreated with elastic water proofing sealing tape with a woven bonding on each surface an elastic expansions zone in the centre of make sika Tape S/FOROC/Dr Fixit/STP.
(nn) The membrane has to be protected in accrodance with the manufacture's recommendance until placemnent of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accrodance with manufacturer's recommendations. (oo) Waterproffing treatement has to carried out through applicators authorised.
(i) All the joints of pipesand traps within sunken portion shall be sealed properly by Epoxy sealant.
(ii) All CI traps in sunken slab to be enclased with PCC 1:1:5:3 ( Min 15cm) all - round.
(iii) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40 mm stone aggregate) complete all as specified.
(iv) Providing drainage spout pipe GI 40 mm dia bore light grade upto outside of outer wall (approx 450 mm to 600 mm long) including cutting to existing wall and making good the distrubed surface complete all as specified and directed.
(v) Providing 25 mm thick cement concrete 1:2:4 type B-0 using 12.5 mm grade stone aggregate as in flooring for laying fllor finish all as specified. Note:- Item No 115.01 (iii), (iv) & (v) shall be measured and paid seprately.
-
-
-
... More
M&L for GI steel water tubing, 40mm bore medium grade galvanized with all fittings and fixed to walls and celling or laid in floor including cutting to existing wall and making good the disturbed surface, complete all as specified and directed.
32
-
-
... More
M&L for Cement concrete (1:5:10) type E-2 using 40 mm graded stone aggregate as in filling in sunken slab or as in sub base, mass concrete , complete all as specified and directed.
54.6
-
-
... More
Demolition of reinforced cement concrete in any position, complete all as specified and directed.
29.92
-
-
... More
M&L Reinforced cement concrete nominal mix (1:2:4),type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.
29.92
-
-
... More
Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) rough surfaces of concrete, complete all as specified and directed.
307.88
-
-
... More
Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide rough surfaces of concrete, complete all as specified and directed.
146.08
-
-
... More
Surface dressing n exc15 cm deep in soft loose soil, complete all as specified and directed.
2775
-
-
... More
Cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base of floor topping, 75 mm thick, complete all as specified and directed.
2615
-
-
... More
M&L Machine pressed precast concrete interlocking paver block any shape, colour and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade, jointed and pointed with grey cement and pigment over sand cushioning, complete all as specified and directed.
2615
-
-
... More
M&L sand filling /sand cushioning under floors or in foundations including consolidation, complete all as specified and directed.
65.38
-
-
... More
Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, complete all as specified and directed.
53
-
-
... More
S&F mild steel TMT bars as in reinforcement 10mm dia and over cut to length,bent to shape required including cranking, bending spirally for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and directed.
2341
-
-
... More
S&F mild steel TMT bars as in reinforcement 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length,bent to shape required including cranking, bending spirally for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and directed.
516
-
-
... More
M&L for shotcreting average thickness 50 mm in RCC columns, beams and slab etc. with cement concrete M-25 design mix having minimum cement content of 350 Kg per Cum. Concrete having the specified minimun characterstic compressive strength (with ordinary portland cement, coarse sand and graded stone aggregates of 6 mm maximum size in proportion as per design criteria and Hardener/ admixture) incl the cost of centering and shuttering at edges and corner etc as directed by Engineer-in-Charge incl chipping of unsound/week concrete mateial 50 mm average thickness from slabs, beams/ columns etc with mannual chiesels or standerd power driven percussion type machine incl tapering of all edges, make square shoulder of cavities incl cleaning the exposed concrete surface and reinforcement with wire brushes and throughly washing with water and allowing it to dry etc incl removal of rust by applying approved rust remover chemical and the coating with Dr Fixit Epoxy zinc primer @ 6 Sqm per Litre at DFT of 100 micron, applying the SBR Latex based bonding agent on each layer of the shootcreting work of Dr Fixit Pidicrete URP on the entire surface complete all as directed including pressure grouting with epoxy injection grout including 5 mm thick cement plaster in CM (1:3) finished even and smooth without using extra cement including removing rubbish material from building and thrown in low lying lying area at any distance upto 500 metres from the site , complete all as specified and directed. Make of chemical : Epoxy bonding agent, Rust remover, Anti corrosive coating, Epoxy grout, Hardener/ admixture shall be of Berger/ Sika/Fosroc/Pidilite or Techno commercial or equivalent make approved by GE.
Notes:- (i) Complete treatment to be executed by approved applicator (Applicator to be approved by GE).
(ii) The Contractor and manufacture of shotcrete shall give the warranty before commencement and also for the strengths achieved in the post completion of work.
(iii) The chemicals to be used in the work shall be certified by the approved manufacturer .
(iv) Hard drawn steel wire fabric will be measured and paid seperately.
439
-
-
... More
Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 , complete all as specified and directed.
7021
-
-
... More
M&L for applying bond coat of epoxy bonding agent & cement mortor in 1:1 ratio for bonding old and new concrete on damaged surfaces applying ready mix polymer modified mortar upto 60mm thickness (Chajjas fins, border,slab, beams etc):-
(i) Including application of rust remover on exposed reinforcement and subsequent application of anticorrosive coating. Also, pressure grouting with epoxy injection after application of polymer modified mortar.
(ii) Use of electrical mixer to get the homogeneous dough on bond coat surfaces. (iii) To achieve required thickness repeat this step after 24 hrs as required.
(iv) Keep the surfaces moist using water forg for 5 to 7 days etc complete all as specified and as directed.
(v) Rate shall be inclusive of all necessary scaffolding for building height up to 24 meters complete all as directed by Engineer-in-Charge.
Make of Chemicals : - Epoxy bonding agent, Rust remover, Anti corrosive coating, Polymer modified mortar, Epoxy grout shall be of Berger, Krishna, Dr Fixit, MC Bauchemie and M/s Cemistik, Sika or Equivalent as approved by GE.
Notes:- (i) Complete treatment to be executed by approved applicator (Applicator to be approved by GE). (ii) The Contractor and manufacture of polymer modified mortar shall give the warranty before commencement and also for the strengths achieved in the post completion of work.
(iii) The chemicals to be used in the work shall be certified by the approved manufacturer.
(iv) Hard drawn steel wire fabric will be measured and paid seperately.
770
-
-
... More
S&F hard drawn steel wire fabric not exc 4 kg/sqm cut to lengths, wire mesh to be fixed and firmly anchored to the concrete surface by means of 'L' shaped mild steel shear key welded with existing reinforcement including cost of material, labour, tools and plants incl welding/L-clip/tying with mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and directed.
1948
-
-
... More
M&L for cleaning the blockage of bathroom/kitchen by cleaning the nanhi traps/gully traps of all the mud/sludge and getting out washing throughly traps, CI waste pipe by opening the cleaning eyes and depositing the sludge in a pit of suitable size at a distance not exceeding 100m from the gully trap and covering the same with the soil obtained from excavation of pit including excavation and earth work, complete all as specified and directed.
104
-
-
... More
E/M Portion
-
-
-
... More
Taking down carefully existing point wiring of any type (i.e on wooden batten, surface conduit, casing capping or concealed conduit except existing conduit) complete for light, fan, socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets wooden batten, conduit etc including accessories such as wooden gutties/ rawal plug, screw etc including removing materials from site for taking credit of unserviceable items and re-fixing the serviceable items as per schedule and making good disturbed surface of walls, floors etc, complete all as specified and directed. Note:- (i) The existing conduit of concealed wiring will not be removed from site and same will be reused for point wiring under respective item hereunder.
(ii) The qty of serviceable/ unserviceable items will be ascertained by the BOO detailed by GE and serviceable items (such as LED fittings/LED tube and bulb /ceiling/ Exhaust Fans and geysers) will be refixed under respective item hereunder and unserviceable items such as switches, sockets, ceiling rose, holders, brackets, bulkhead fittings, LED fittings, MCB DBs, sunken boxes and fixtures etc. shall be issued to contractor under schedule of credit all as specified and directed.
2464
-
-
... More
M&L for point wiring with 1.5 sqmm, PVC insulated but unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through existing metallic/rigid PVC concealed conduit including replacement of pressed steel terminal mounting box, for mounting fitting like modular switches, sockets, and fixed with brass screws and cup washers including one continuous run of PVC insulated 1.50 sqmm size copper conductor cable green in colour as a earth wire and connected to common earth dolly, complete all as specified and directed. Note:- Cost of Metal boxes and modular accessories like cover plates will be paid seprately in respect items (For JCO/ORs Md Accn against the existing points).
-
-
-
... More
Fan point/exhaust fan point/one light point/bell/buzzer controlled by one switch/bell push.
1353
-
-
... More
One light point controlled by two Nos of two way switch.
6
-
-
... More
One socket outet point 5 amps on the same board.
272
-
-
... More
One socket outet point 5 amps on the independent board.
239
-
-
... More
All as Ser item 135 here in before but with 2.5 sqmm wire and earth wire of 2.5 sqmm for 3 Pin 15 Amp modular type socket outlet, complete all as specified and directed.
106
-
-
... More
M&L for point wiring with 1.5 sqmm, PVC insulated but unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit medium grade 20mm dia (minimum) or higher size as specified and cutting chasing on wall complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc/ fittings ISI marked for modular fittings and brass screws and cup washers including 1.5 sqmm stranded copper conductor PVC insulated FRLS cable green in colour as continuous earth conductor connected to common earth and earth dolly with all accessories, complete all as specified and directed. Note:- Cost of Metal boxes and modular accessories like cover plates will be paid seprately in respective items (For JCO/ORs Md Accn against new SOA 2022 and existing unsv and dismantle conduit pionts).
-
-
-
... More
Fan point/exhaust fan point/one light point/bell/buzzer controlled by one switch/bell push/street light.
763
-
-
... More
One light point controlled by two Nos of two way switch.
19
-
-
... More
One socket outet point 5 amps on the same board.
144
-
-
... More
One socket outet point 5 amps on the independent board.
413
-
-
... More
All as Ser item 137 here in before but with 2.5 sqmm wire and earth wire (green colour) of 2.5 sqmm for 3 Pin 15 Amp modular type socket outlet, complete all as specified and directed.
102
-
-
... More
S&F modular metal flush box 1/2 module, complete all as specified and directed.
286
-
-
... More
S&F modular metal flush box 3 module, complete all as specified and directed.
832
-
-
... More
S&F modular metal flush box 4 module, complete all as specified and directed.
76
-
-
... More
S&F modular metal flush box 6 module, complete all as specified and directed.
132
-
-
... More
S&F modular metal flush box 8 module, complete all as specified and directed.
340
-
-
... More
S&F modular white cover plate with frame,1/2 module, complete all as specified and directed.
286
-
-
... More
S&F modular white cover plate with frame, 3 module, complete all as specified and directed.
832
-
-
... More
S&F modular white cover plate with frame, 4 module, complete all as specified and directed.
76
-
-
... More
S&F modular white cover plate with frame, 6 module, complete all as specified and directed.
132
-
-
... More
S&F modular white cover plate with frame, 8 module, complete all as specified and directed.
340
-
-
... More
S&F modular Dummy plate, complete all as specified and directed.
85
-
-
... More
S&F modular switch 6 Amp 1 way 1 module size, complete all as specified and directed.
3080
-
-
... More
S&F of modular switch 6 Amp 2 way 1 module size, complete all as specified and directed.
50
-
-
... More
S&F of modular switch 16 Amp 1 way with indicator 1 module size, complete all as specified and directed.
208
-
-
... More
S&F of modular socket shuttered 6 Amp 2/3 pin combined 2 module size, complete all as specified and directed.
1068
-
-
... More
S&F of modular socket 16Amp multipurpose type 2 module size, complete all as specified and directed.
208
-
-
... More
S&F of modular Fan regulator step type 120 watts 2 Module size, complete all as specified and directed.
340
-
-
... More
S&F of modular bell switch 6 Amp, 1 module size, complete all as specified and directed.
104
-
-
... More
S&F of Ceiling rose, surface bakelite 3 terminal, 240 volts, 5 Amps with back plate of 3 mm thick bakelite, laminated hylem sheet of appropriate size, complete all as specified and directed.
1124
-
-
... More
S&F lamp holder, PVC/polycarbonate type insulated body with back plate suitable for batten/angle fittings including led lamp 9 watt, complete all as specified and directed.
444
-
-
... More
S&F LED lamp 9 watt polycarbonate, complete all as specified and directed.
444
-
-
... More
S&F decorative 9W LED wall mounting fittings complete set including 9W LED lamp , complete all as specified and directed. Cat No LHF0ECEITZIB014 Glaze Wall light of Havells or eqvt in Philips/Crompton.
312
-
-
... More
S&F of single phase call bell ‘DING DONG’, AC 230 volts single pole fixed over and including pressed steel sunk box of size 175 X 100 mm duly covered with 3 mm thick bakelite sheet, complete all as specified and directed.
104
-
-
... More
S&F MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type, complete all as specified and directed.
820
-
-
... More
S&F MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘C’ curve type, complete all as specified and directed.
220
-
-
... More
S&F MCB SPN, 240 volts, 40 to 63 Ampere, rupturing capacity 10 KA, ‘B’ curve type, complete all as specified and directed.
104
-
-
... More
S&F sheet metal enclosure for DB’s (Double door type) when MCB’s to be used, single pole and neutral, 12 ways with 200 ampere rated bus bar, 240 volts fixed sunk / flush to the wall with IP-43 and IK-09 protection, complete all as specified and directed.
104
-
-
... More
S&F MCB single pole, 240 volts, 40 Ampere, rupturing capacity 10 KA, ‘B’ curve type, complete all as specified and directed.
155
-
-
... More
S&F Factory made sheet metal enclosures double door type made out of CRCA 1.2 mm thick M.S. sheet, powder coated, partly embedded in wall, IP-43 protection, VTPN DB with 200 Amps rated bus bar, 4 way, 415 volts, vertical type, dust and vermin proof, suitable for incorporation of MCCBs/ MCBs, factory made, including thermal based release adjustable type 4 pole 63 Amps, 50 Hz, 415 Volts with rupturing capacity 16 KA and making good distrubbed surfaces with matching colour, complete all as specified and directed.
25
-
-
... More
M&L for sub main wiring with 1100 volt grade two single core FRLS Wire PVC insulated and unsheathed cable with stranded copper conductor 6 sqmm drawn into and including electrical grade PVC conduit not less than 25 mm dia with IS 9537 (Part-III) 1983 mark, or relevant ISI mark with all accessories fixed concealed including chase cutting in brick/ stone masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 6 sqmm multi - stranded copper conductor as earth wire in green colour including taking down old unserviceable sub main wiring, complete all as specified and directed. Note:- Two runs of 6 sqmm PVC FRLS multi stranded copper cable wire and One run of 6 sqmm PVC FRLS multi stranded copper cable earth wire and One run (01 meter) PVC conduit of suitable size ISI mark will be measured and one unit length.
1020
-
-
... More
M&L for sub main wiring with 1100 volt grade two single core FRLS Wire PVC insulated and unsheathed cable with stranded copper conductor 4 sqmm drawn into and including electrical grade PVC conduit not less than 25 mm dia with IS 9537 (Part-III) 1983 mark, or relevant ISI mark with all accessories fixed concealed including chase cutting in brick/ stone masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 4 sqmm multi - stranded copper conductor as earth wire in green colour including taking down old unserviceable sub main wiring, complete all as specified and directed. Note:- Two runs of 4 sqmm PVC FRLS multi stranded copper cable wire and One run of 4 sqmm PVC FRLS multi stranded copper cable earth wire and One run (01 meter) PVC conduit of suitable size ISI mark will be measured and one unit length.
1276
-
-
... More
S&F in replacement of LED tube light fitting for all purpose surface and wall mounted with single side connection polycarbonate LED batten with alumimium housing and integrated electronic driver of capacity 20 W, four feet and connection with PVC insulalted twin core 23/0.0076 twisted copper cable from ceiling rose to tube light fitting, complete all as specified and directed.
119
-
-
... More
Fixing only servicable LED Tubelight fittng 18/20/22 watts, as per Srl item No 134 after B/R repairs and making electrical connection, complete all as specified and directed.
355
-
-
... More
S&F wall/ceiling mounting LED 9/10 Watt tube light fitting complete with all acessories 1x9 Watt LED, with CCT of 6000k suitable for domestic application, 240 Volts, 50 Hz, and internally pre-wired with 1.5 sqmm twin twisted flexible cable copper conductor and connection, complete all as specified and directed.
104
-
-
... More
S&F energy saving new generation 10 watt LED built up, 6000k bulk head luminaire with opal diffuser light fitting including 10 W Bulb complete with all acessories and connection, complete all as specified and directed.
104
-
-
... More
S&F in replacement of security light fitting LED 35 Watt with aluminum pressure dia cast housing with touched glass cover IP-66 protection Including suitable size GI Bracket and accessories complete mounted including connection with 3 core PVC insulated overall sheathed flexible cable with muyltistranded copper conductor of size not less than 1.0 sqmm from celing rose to fitting terminal including taking down old CFL security light fitting, complete all as specified and directed.
56
-
-
... More
M&L for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board/main DB’s/earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1, duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1, GI protection pipe light grade 15 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 X 150 X 15 mm & painting of earth result etc. including testing on complete all as specified and directed. Note:- (i) Earth lead and protection pipe beyond 7.5 m shall be measured and Paid separately. (ii) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt.
25
-
-
... More
S&F fresh air fan 250mm size including making of hole/opening in wall, complete all as specified and directed.
104
-
-
... More
Fixing only of geyser (Electric Water heater storage type) of capacity 25 Lts, keep in safe custody as per srl No 134, after B/R repairs. Note:- Cost of minor petty items if required such as nut bolt/Pvc pipe is included in quoted rate.
44
-
-
... More
S&F of electric water heater,storage type steel body with SS 304 inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc, complete all as specified and directed.
60
-
-
... More
Fixing only ceiling fan 1200/1400 mm size, as per item srl No 134 after B/R repairs. Note:- Cost of minor petty items if required such as nut bolt/clamp is included in quoted rate.
340
-
-
... More
Fixing only exhaust fan/ fresh air, keep in safe custody as per item srl No. 134 after B/R repairs. Note:- Cost of minor petty items if required such as nut bolt/clamp is included in quoted rate.
36
-
-
... More
S&F of exhaust fans metal body AC single phase 230/240 V of size 300 mm sweep with louver and including making of hole/opening in wall, complete all as specified and directed.
68
-
-
... More
S&F of metal enclosure (plug & socket type DB) complete including single pole and neutral enclosure with two pin, earth plug and socket complete with one SP MCB C Curve type of capacity 20 Amp, 10 KA, complete all as specified and directed.
128
-
-
... More
Fixing only and connecting electric meters upto 60 Amps after B/R repairs. Note:- Cost of minor petty items if required such as nut bolt/clamp is included in quoted rate.
64
-
-
... More
S&F PVC insulated unsheathed copper wire 1.5 sqmm FRLS single core 1100 volt for inverter connection in same conduit, complete all as specified and directed.
1248
-
-
... More
S&F Rigid non metalic PVC conduit pipe 20 mm dia including all tee bend elbow reducer bell mouth tube ends and fixing accessories such as coplers lock nuts saddles pipe hock etc, complete all as specified and directed.
1040
-
-
... More
S&F sheet steel metal enclosure single pole & neutral with a 2 pin and earth plug and socket complete with one single pole MCB SP 20 Amp, 240 volts, complete all as specified and directed. (For Geyser & AC Point)
80
-
-
... More
Fixing only and connecting electric meters upto 25 Amps after B/R repairs. Note:- Cost of minor petty items if required such as nut bolt/clamp is included in quoted rate.
40
-
-
... More
M&L for laying of LT cable of 1100 volt XLPE insulated and PVC sheathed of size 25 sqmm 4core with cable gland including taking down old unserviceble cable , complete all as specified and directed. (For JCO/OR Md Accn).
690
-
-
... More
S&F laying galvanised pipe 40 mm bore light grade fixed to pole with clamps nuts, bolts and washers or laid under road crossing or fixed to wall, complete all as specified and directed.
78
-
-
... More
M&L for excavation in trenches in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 meter deep for laying of cable, pole foundation, etc including taking out old brick cable protection cover and getting out forming bottom surface to required gradient, complete all as specified and directed.
215.19
-
-
... More
M&L for returning, filling in, earth including spreading, leveling watering and well ramming in layers each not exceeding 25cm thick each layer, complete all as specified and directed.
129.59
-
-
... More
M&L for removal of surplus soil to a distance not exc. 50 meter and depositing where directed at a level not exc. 1.5 meter above the starting point, complete all as specified and directed.
77.37
-
-
... More
M&L for Sand cushioning to under ground cable in trenches/existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable, complete all as specified and directed.
64.55
-
-
... More
M&L Bricks; common burnt clay building bricks, sub-class ‘B’ designation 75 laid dry width wise across the line of cable in trenches for protection of UG cable, complete all as specified and directed.
6.92
-
-
... More
Supply and laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sqmm 4 core, complete all as specified and directed.
265
-
-
... More
Supply and laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 35 sqmm 3.5 core, complete all as specified and directed.
126
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%