Military Engineer Services Tender

Cement concrete 1:3:6 type C-2 using 40 mm graded crushed stone aggregate in foundation filling and mass concrete for poles/struts/stays assembly including use and waste of necessary form work complete all as specified and as directed.

Supplying, Laying connecting and testing XLPE insulated, PVC sheathed, armoured HT electric power UG cable (heavy duty with stranded aluminum conductor) of size 95 Sqmm, 3 core, 11000 Volts(Earthed) grade, confirming to IS-7098 (Part-II) laid through duct/ pipe / in trench etc. with cable glands and suitable size of aluminium lugs complete all as specified and as directed. Note :- Earth work, concrete cable covers, sand cushioning and GI Pipe shall be measured and paid separately under respective item.

Supply, laying, Jointing connecting LT UG cable XLPE insulated,PVC bedded galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 120 sqmm 3.5 core laid in trenches / on poles / walls / in ducts / passing through pipes and including necessary cable lugs, bolts, nuts and washers complete all as specified and as directed.

All as per serial item No. 6.00 here in before but for 95 Sqmm 3.5 Core.

Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed including painting two coats of aluminium paint over a coat of primer complete all as specified and as directed.

Pin type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 150mm height, 150mm dia for 11000 volts grade complete all as specified and as directed.

LT feeder pillar box with new feeder pillar, installation, testing and commissioning, factory fabricated prewired, CPRI aproved, cubical type of appropriate size out door, dust and vermin proof, made out of 50x50x6mm angle iron frame/legs and 3.15 mm thick CRCA sheet with openable shutters on both sides (front & rear), powder coated externally and internally, having locking arangement mounted on four legs 90cm high (30 cm below ground level and 45 cm above ground level), Panel. embedded in PCC (1:2:4 ) type B2 block and neccessary brick work including Copper bus bar 200 A for three phase and neutral duly insulated with sleeves of different colour RYB complete all as specified and as directed to accommodate the following accessories :- INCOMING (a) MCCB , 160 Amps, 4 pole, 415 volts, 36 KA Adjustable type - 01 Nos (b) MCCB, 100 Amps, 4 pole ,415 volts, 36 KA adjustable type-01 Nos (b) Voltmeter square type 96 x 96 mm 0-500 V (Digital type)- 01 No. (c) Ampere meter square type 96 x 96 mm 0- 300Amps with CT (Digital type)- 01 set (d) Indicator lamp neon/LED type (set of three ) OUT GOING (a)    MCCB , 125 Amps, 4 pole, 415 volts, 36 KA Adjustable type - 02 Nos (b) MCCB, 100 Amps, 4 pole ,415 volts, 36 KA adjustable type-02 Nos.

Earthing complete with galvanised steel earth plate electrode 60cm×60cm× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion. Note:- Length upto 7.50m of GI wire and protection pipe is inclusive in unit rate.

Earthing complete with galvanised steel earth plate electrode 60cm×60cm× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to using galvanised iron strip 32×6 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion. Note:- Length upto 7.5m of GI strip is inclusive in unit rate.

Earth continuity conductor 32x6 mm size galvanised iron Strip fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe fixed to poles or any other indicated situation for loop earthing etc. as required complete all as specified and as directed.

Earth continuity conductor 4 mm dia galvanised iron or steel wire fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe fixed to poles or any other indicated situation for loop earthing etc. as required complete all as specified and as directed.

Cable jointing kit for HT 11 KV (Earthed) grade heat shrinkable end termination outdoor type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 70 to 95 sqmm complete all as specified and as directed.

Cable jointing kit for LT PVC insulated armoured heavy duty cable120-185 Sqmm 3.5 core, end terminal joints ( heat shrinkable) any type along Pole etc suitable for aluminium conductor cable and testing after jointing complete all as specified and as directed.

Cable jointing kit for LT PVC insulated armoured heavy duty cable 50-95 Sqmm 3.5 core end terminal joints ( heat shrinkable) any type along Pole etc suitable for aluminium conductor cable and testing after jointing complete all as specified and as directed.

HT lightening arrestor, expulsion type, with all fittings, transmission class, discharge capacity 65 Kilo Amps suitable for 11 KV complete all as specified and as directed.

GOD Triple Pole mechanically operated mounted on 12 insulator and steel frame with operating mechanism worked from ground level of 11000 volt grade for current rating 200 Amps with DP fuse including taking down old unservicable gang operated device, necessary connection complete all as specified and directed.

Automatic power Factor correction (APFC ) Panel for 3 Phase , 415 volts & 50 Hz system of capacity 30 KVAR (3x10 KVAR capacitor bank) with incoming MCCB of 63 Amp complete all as specified and as directred.

Supply only chain link fencing made out of 3.15mm dia galvanised iron wire of mesh 50mm x 50mm size ,made upto into mattress or cages complete all as specified and as directed. Note: Weight of chain link fencing will be decided by BOO before payment

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified and directed.

Excavation in post holes n exc 0.5 cum each, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick in soft / loose soil complete all as specified and as directed.

Mild Steel work for posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Preparing steel and iron surfaces of any description and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge.

Danger notice plate of 1.2 mm thick mild steel sheet, vitreous enamelled white with letters figures and conventional skull and bones in signal red colour and fixed with MS clamps bolts and nuts of approved size for HT 30x20 cm size duly written in Punjabi, English & Hindi languages complete all as specified and as directed..

Horizontal cutting of Road/PCC surface by machine without damaging near by area upto depth of 2.5 feet for laying /crossing of GI protection pipe of 80mm complete all as specified and as directed. Note : GI pipe shall be measured and paid seperately.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr depth for foundation , poles struts , laying of cables and getting out in hard/dense soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 mtr wide and exceeding 1.5 mtr but not exceeding 3.00 mtr depth for foundation , poles struts , laying of cables and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm as in soils complete all as specified and directed.

Removing excavated material not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point as in soils complete all as specified and as directed.

Sand cushioning with dry river sand in trenches for cushioning of underground cable with layer of sand 8 cm before laying of cable and 15 cm thick after laying of cable complete all as specified and as directed. NOTE: For payment purpose punned thickness of 18 cm shall be measured against spread thickness of 23 cm as mentioned in para 19.75 of SSR Part-I.

Factory made unreinforced Precast concrete cable covers class LV type 1, flat, Size 250x150x40mm laid in trenches as protection to cables complete all as specified and as directed.

Factory made unreinforced Precast concrete cable covers class HV type 1, flat, Size 300x180x40mm laid in trenches as protection to cables complete all as specified and as directed.

GI tube light grade, 80mm bore as in cable protection pipe including all fittings complete all as specified and as directed.