Military Engineer Services Tender

Returning, filling in, including spreading, leveling,watering and well ramming in layers each n.exc 25 cm thick in soft loose soil all as specified.

Supply and lay brick common burnt sub class "B" old size (compressive strength not less than 75 kg per sqcm) for protection of cable laid in trenches for under ground cable all as specified.

M & L for Sand cushioning trenches using fine sand to under ground cable, laid in two layers 15cm before laying the cable & 8cm after laying the cable complete all as specified and directed.

Supply and fixing in repair for cable protection GI tubing light grade fixed along the pole/wall/under road of size 100 mm bore with necessary clamps, nut and bolts all as specified and directed by Engineer -in-Charge. Note : Clamps, nut and bolt will be measured and paid separately.

All as per srl item No. 7 here in beore but Size 80 mm

All as per srl item No. 7 here in beore but Size 50 mm

All as per srl item No. 7 here in beore but Size 40 mm

Supply and laying in replacement XLPE insulated armoured (under ground) heavy duty electic cablewith stranded aluminim conductor 1100 volts grade of crossectional area 300 Sqmm 3.5 core laid in trenches/ducts/through pipes/in floor road/along the pole etc all as specified & direc0ted by Engr-in-charge. Note : (a) Excavation earth work, brick protection and cushioning shall be measured & paid separately. Make: Havells , CCI, Rallison

All as per srl item No. 11 here in before but Size 240 Sqmm 3.5 core

All as per srl item No. 11 here in before but Size 185 Sqmm 3.5 core

All as per srl item No. 11 here in before but Size 150 Sqmm 3.5 core

All as per srl item No. 11 here in before but size 120 Sqmm 3.5 core

All as per srl item No. 11 here in before but size 95 Sqmm 3.5 core

All as per srl item No. 11 here in before but size 70 Sqmm 3.5 core

All as per srl item No. 11 here in before but size 50 Sqmm 3.5 core

All as per srl item No. 11 here in before but size 35 Sqmm 3.5 core

All as per srl item No. 11 here in before but size 25 Sqmm 4 core

All as per srl item No. 11 here in before but size 16 Sqmm 4 core

Providing PCC 1:4:8 type D:2 using 40mm graded crushed stone aggreate as in foundation for pole/stay assembly foundation etc all as specified and directed by Engineer-in-Charge.

Providing PCC 1:3:6 type D:2 using 40mm graded crushed stone aggreate as in foundation for pole/stay assembly etc all as specified and directed by Engineer-in-Charge.

Providing PCC 1:2:4 type B:2 using 40mm graded crushed stone aggreate as in coping of pole including necessary form work and fair finish to exposed surfaces complete all as specified and directed.

M&L for stay assembly complete comprising of 7/3.15 galvanised stranded stay wire of required length, fixed to pole with and including FI clamps 50x6mm, bolt, nuts washers, GI stay rod 20 mm dia and 1800 mm long stay bow 400x14 mm, GI steel plate 300x300x6mm, loop insulator of size 90x140mm clearance hole 16 mm including two coats of aluminium paint over a one coat of red oxide primer on exposed mild steel work all as shown in Electrical Plate no 1 of SSR part-I 2009 on page No 495 complete all as specified and directed. (Note : Excavation & PCC works measured separately).

Supply and erecting in Steel tubular swaged poles complete with cast iron base plate, final taper plug, bolts, nuts & screws as specified type 410 SP-31 (9 metres long).

Supply and erecting in vertically prestressed concrete pole LT pole 9.0 mtr long 102 x 172mm at top and 102mm x 279mm at bottom class 10 all as specified and directed.

M & L for synthetic chequered insulated mat, ISI marked of size 2mx1mx19mm Conforming to IS- 15652 / 2006.

M & L for Re-Stringing/Stretching of existing ACSR conductor of any size any type as required sag fixed on OH line incl unwindinding the conductor & insulators/cross Arms on poles properly binding with alumminum all as specified and directed.

M&L for road cutting ,including excavation returning filling in,spreading ieveling, well ramming in layers, soiling with, broken boudders/ stones, WBM 7.5 cm thick coarse aggregate received from dismentling the existing WBM of road , watering and ramming , 40 mm thick PCC 1:2:4 using 20 mm using 20 mm graded stone aggregate for road patch repair work, section/cross section area of cutting shall be as specified and as directed by Engineer -in Charge.

Supply and fixing cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material heat Shrink type and accessories suitable for 3½ core XLPE, armoured, Al conductor cable of size 240 to 300 sqmm,Indoor/Outdoor type complete all as specified and directed.

All as per Srl item 31 above but of size 150 to 185 sqmm.

S & F LT heat shrinkable type indoor/outdoor end termination cable jointing kit with jointing material and accessories suitable for 1100 volt (Earthed) grade 3½ core XLPE, armoured, Al conductor cable of size 240 to 300 sqmm,complete all as specified and directed.

All as per Srl item No 33 but of size 150 to 185 sqmm .

Supplying, installing, testing of LT out door feeder pillar box double door type with neoprene rubber gasket and locking arrangement vermin/dust / weather proof, self ventilation with wire mesh at suitable interval on both side, totally enclosed, busbar chamber, fullly comparted type, front openable hinged independent door for each compartment with common openable hinged door with proper locking arrangement and front and rear side with L drop locking of suitable size made out of 3.15mm thick CRCA sheet duly powder coated paint, cting the incoming / out going feeders by providing cable glands and cable lugs complete all as specified and directed comprising of following accessories. (i) Incomer: ACB 4 Pole, 415 V, with microprocessor release IPR3+ (LSIG +LCD Display+Thermal Memory+ zone Selectivity+Current & voltage Mesurment+Advance Protection+over tempeture protection).630 Amps 50 KA, Manual Drawout type. (ii) Bus Bars :800A TPN+E aluminium busbars suitable for Outgoing Feeders:- (iii) 4Nos 250 Amp 4P 36KA Microprocessor MCCB with adjustable thermal and adjustable magnetic setting including spreader terminal kit both side.-Outgoing (iv) 01 Nos 100 Amp 3P 16KA MCCB with adjustable thermal and fixed magnetic setting including spreader terminal kit both side. (v) Volt meter 0 to 500 volts digital type including inbuilt VSS = 1 No (vi) Ampere meter 0 to 500 Amp digital type including inbuild slector swtich =1 No (vii) LED Phase indicator lamp Set of three.

(vi) Ampere meter 0 to 500 Amp digital type including inbuild slector swtich =1 No (vii) LED Phase indicator lamp Set of three. (viii) All connections from MCCBs to bus bar & bus bar to MCCB shall be made with suitable size of aluminium strip thimble lugs cost of which included in the quoted rate of item. (ix) All acessories prewired with copper conductor cable single strand PVC insulated with aluminium thimbe lugs etc all as specified and directed (x) Above all complete in all respect including installation of panel and frame pedestal legs made of ISA 5050 of size 40x40x6 mm of length 900 mm . 450 mm below the ground and 450 mm above the gound level grouted in PCC 1:3:6 type C-1 (using 20mm graded stone aggregate).

S&F in repair MCCB AC 415 volts, 63 Amp rating, breaking capacity of 25 KA, Adjustable thermal and fixed Magnetic ,With Two side Spreader thermal kit, 3 Pole, Conforming to IEC:60947-II / IS:13947-II) all as specified and directed ((Make Havells / L&T / Legrand / Schneider)

S&F in repair MCCB AC 415 volts, 100 Amp rating, breaking capacity of 16 KA, Adjustable thermal and fixed Magnetic ,With Two side Spreader thermal kit, 3 Pole, Conforming to IEC:60947-II / IS:13947-II) all as specified and directed ((Make Havells / L&T / Legrand / Schneider)

S&F in repair MCCB AC 415 volts, 125 Amp rating, breaking capacity of 16 KA, Adjustable thermal and fixed Magnetic ,With Two side Spreader thermal kit, 4 Pole, Conforming to IEC:60947-II / IS:13947-II) all as specified and directed ((Make Havells / L&T / Legrand / Schneider)

S&F in repair MCCB AC 415 volts, 160 Amp rating, breaking capacity of 36 KA, 4 Pole, Conforming to IEC:60947-II / IS:13947-II) all as specified and directed ((Make Havells / L&T / Legrand / Schneider)

S&F in repair MCCB AC 415 volts, 200 Amp rating, breaking capacity of 36 KA, Adjustable thermal and fixed Magnetic ,With Two side Spreader thermal kit, 4 Pole, Conforming to IEC:60947-II / IS:13947-II) all as specified and directed ((Make Havells / L&T / Legrand / Schneider)

S&F in repair MCCB AC 415 volts, 250 Amp rating, breaking capacity of 36 KA, 4 Pole, Conforming to IEC:60947-II / IS:13947-II) all as specified and directed ((Make Havells / L&T / Legrand / Schneider)

S&F in repair MCCB AC 415 volts, 400 Amp rating, breaking capacity of 36 KA, 4 Pole, Conforming to IEC:60947-II / IS:13947-II) all as specified and directed ((Make Havells / L&T / Legrand / Schneider)

A Schedule of Credit for old/unserviceable demolished/ dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.