Military Engineer Services Tender

Material and labour for sand cushioning with a layer of sand 8cm thick before laying of cable and 15cm thick after laying of cable in trenches complete all as specified and directed by Engineer-in-Charge. Note : For payment purpose 18cm thickness shall be considered.

Material and labour for Protection to cable with one layer of new bricks laid flat butting to each other in such a way that the length of the bricks is at right angle to the central axis of the cable using old size sub-class ‘B’ bricks complete all as specified and directed by Engineer-in

Taking down GI pipe 20mm bore including fitting and supply and fixing GI tubing medium grade 20mm bore in any length with all fitting laid in trench and connecting up with water supply main complete all as specified and directed by Engr-in-Charge.

All as per item ser No 6 above here in before but 25mm bore complete all as specified and as directed by Engr-in-Charge.

All as per item ser No 6 above here in before but 40mm bore complete all as specified and as directed by Engr-in-Charge.

All as per item ser No 6 above here in before but 50mm bore complete all as specified and as directed by Engr-in-Charge.

Taking down old unserviceable CI pipe 100mm bore and supply, laying, jointing and testing new cast iron pipe 100 mm bore centrifugally cast class LA confirming to IS - 1536 spigot and socketed ends in any length laid in trenches complete all as specified and directed by Engr-in-Charge. (Note : Excavation, earth work, CI fitting and new run lead joint shall be measured and paid for separetely under appropriate item of Sch 'A')

Taking down old unserviceable DI pipe 100mm bore and supply, laying, jointing and testing new DI (K-7) 100 mm bore centrifugally cast class LA confirming to IS - 1536 spigot and socketed ends in any length laid in trenches complete all as specified and directed by Engr-in-Charge. (Note : Excavation, earth work, CI fitting and new run lead joint shall be measured and paid for separetely under appropriate item of Sch 'A')

Taking down old unserviceable CI pipe 150mm bore and supply, laying, jointing and testing new cast iron pipe 150 mm bore centrifugally cast class LA confirming to IS - 1536 spigot and socketed ends in any length laid in trenches complete all as specified and directed by Engr-in-Charge. (Note : Excavation, earth work, CI fitting and new run lead joint shall be measured and paid for separetely under appropriate item of Sch 'A')

Taking down old unserviceable DI pipe 150mm bore and supply, laying, jointing and testing new DI (K-7) 150 mm bore centrifugally cast class LA confirming to IS - 1536 spigot and socketed ends in any length laid in trenches complete all as specified and directed by Engr-in-Charge. (Note : Excavation, earth work, CI fitting and new run lead joint shall be measured and paid for separetely under appropriate item of Sch 'A')

Supply and fixing in replacment of gun metal globe or gate valve with iron wheel head screwed both ends suitable for galvanised pipe 20 mm bore complete all as specified and directed by Engr-in-Charge.

All as per item ser No 14 above here in before but 25mm bore

All as per item ser No 14 above here in before but 40mm bore

All as per item ser No 14 above here in before but 50mm bore

S&F in replacement GI coloumn pipe 100mm dia heavy duty 'C' class with flanged ends drill 3 meter including joining to exising main pipe line complete al as specified and directed by Engr-in-Charge. Note : The cost of nuts bolts washers packing materials and pressure gauge shall be deemed to include in unit rate quoted by the contracror.

Supply and fixing in repair lead joint suitable for CI pipe 80mm bore complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair lead joint suitable for CI pipe 100 mm bore complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair lead joint suitable for CI pipe 150 mm bore complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement cast iron fitting such as bends, tapers, (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc) Tee pieces single branch. "Y" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs tee pieces, single branch for spigot and socket and flanged pipe up to 150mm bore complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement cast iron sluice valve 80mm bore with flanged ends, ISI mark with Gun metal spindle, CI gate with brass ring and iron wheel handle with jointing material such as nuts /bolts washers and rubber insertion sheet etc complete all as specified and as directed by Engr-in-Charge.

All as per srl item No 23 here in before but 100mm dia

All as per ser item No 23 above here in before but 150mm bore

Supply & fixing in replacement Submersible pump set, Electric driven having dischage 1000 LPM at 84 mtr head including suitable capacity of electric motor not less than 30 HP suitable for operation of 415 volts 50 C/S AC supply complete all as specified and as directed by Engr-in-Charge. Make: Crompton/KSB/kirlosker or equivalent as mentioned in list of makes in Appx B-1.

Supply & fixing in replacement Submersible pump set, Electric driven having dischage 1000 LPM at 84 mtr head including suitable capacity of electric motor not less than 25 HP suitable for operation of 415 volts 50 C/S AC supply complete all as specified and as directed by Engr-in-Charge. Make: Crompton/KSB/kirlosker or equivalent as mentioned in list of makes in Appx B-1.

M&L for repairs and servicing of centrifugal pump & Motor sets 100 HP (Make M/S BATLIBOI) electric driven Squirrel cage induction motor 3 phase 415 V AC 50 HZ,opening & cleaning inside of 100 HP motor stator, varnishing and drying, re-winding and duly replacing the following worn out parts of pump and re-erecting, testing and commissioning complete all as specified and directed by Engr-in-Charge. (a) Bearings (b) coupling bolts (c) coupling rubber bush (d) split casing gaskets (e) shaft sleeves (f) replacing the air cocks grease nipple etc (g) painting the pump & Motor with one coat synthetic enamel grey colour paint (Fire Pump House No 1 & 2).

M&L for repairs and servicing of Jocky pump & Motor Set (Make Crompton Greaves) electric driven Squirrel cage induction motor 3 phase 415 V AC 50HZ opening & cleaning inside of 15HP motor stator varnishing and drying, re-winding and duly replacing the following worn out parts of pump and re-erecting, testing and commissioning complete all as specified and directed by Engr-in-Charge. (a) Bearings (b)coupling bolts (c) coupling rubber bush (d) split casing gaskets (e) shaft sleeves (f) replacing the air cocks grease nipple etc (g) painting the pump & Motor with one coat synthetic enamel grey colour paint. (Fire Pump House No1 & 2)

Taking down old u/s bleaching dozing pump along with all accessories and Supply and install connecing testing and commissioning of High Pressuure single Head adjustable "DECLIBAC" Dosing system Model No VST 1005 and VST 1006 of the following specification. Adjustble High Pressure 5 Kg/Sqcm power input 230V, 50 Hz, 40 SPM 1/30 fractional Horsepower, Max output 10 Ltr with mandatory accessories like lead Tubing, connecting ferrules, check valves, etc (A) Preparation tank Model No VST 1005 of net capacity 100 Ltr, FRP dosing tank dia 650 x net Height 375 + conical 300. Gross height with stand 1000 mm consisting of : (i) Water inlet line (ii) Outlet with stainer (iii) Drain (iv) overflow (v) conical bottom for sludge depositing (vi) Pot hole with cover (vii) level gauge (viii) Agitator 120 watt 900 RPM single phase flange mounted motor with plastic shaft and impeller. (B) Service Tank Model No VST 1006 dia 480 x height 575 net capacity 100 Ltr consisting of (i) water inlet line (ii) Dosing pump inlet arrangement (iii) Drain (iv) Overflow (v) Level Gauge (vi) inspection port (vii) Agitator 120 watt 900 RPM Single Phase flange mounted moto with plastic shaft and impeller (ix) provision of mounting Pump on Lid

Material labour and services for taking sample water in sterlised bottles from various borewells for Analysis of water for the following parameters and obtaining sample test report from Govt Recognized Laboratories: (i) Physio Chemical Analysis of Water (Colour, odour, pH Total solids, Dissolved Solids, Permanent hardness, temporary Hardness, Ammonia feree and salinbe, Ammonia Albuminoidal, Nitrites, Nitreates, Oxygen absorption at 15 Min, Iron , Fluoride) (ii) Microbiological Analysis ( Totral Choliforms , Eschirrchea Coli) complete all as specified and as directed by Engr-in-Charge. Note :- 1. A certificate of approval / certification of Lab by Goivt Of India / State Govt shall be submitted by the contractor to the deptt. 2. Sample shall be submitted to the Labortory within 24 Hrs of collection of sample.

Supply of Chlorine test kit with coloured sample complete with all testing fitments and OT solution in Rexene finish Box complete all as specified and as directed by Engr-in-Charge.

Repair to existing valve pits of internal dimensions 90cm x 90 cm x 90 cm making good disturbed/dismantled brick work in cement mortar (1:4) plastering surfaces in CM 1:6, 15mm thick and PCC coping in cement concrete 1:2:4 type B-1 and providing MS cover in replacement made out of MS sheet 3 mm thick duly welded to MS angle iron frame 35x35x5mm including frame work as per existing size with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge. (a) M&L for brick work using sub class 'B' (old size bricks) in CM 1:4 (b) M&L for rendering 15 mm thick in CM 1:4 finishing even and fair (c) M&L for PCC 1:2:4 type B-0 (using cum 12.5 mm graded stone aggregate ) as in coping (d) M&L for any type of mild steel work such as frame sheet 3 mm thick including welding (e) M&L for painting two coats of synthetic enamel paint over a coat of red oxide primer to untreated steel surface & prep of surface.

S&F in replacement unserviceable fully automatic star delta starter in sheet steel enclousure in door type,ML-2 FASD 3 phase phase sequancer corrector with phase loss corrector system working on 415 Volt, 50 Hz, On/Off coil (switch) current capacity 18A, working voltage 12/24 Volt, Cut of voltage (Low) 330-370 (Adjustable), cut of voltage (High) 440-540 Voltage (Adjustable), Phase reversal System, Single phasing protection system, Time delay to start system 150 sec and Off switching time (two stop the system) 440 volt 50 Hz of capacity up to 45 HP including voltmeter and ammeter complete all as specified and as directed by Engr-in-Charge.

S&F in replacement unserviceable fully automatic star delta starter in sheet steel enclousure in door type,ML-2 FASD 3 phase phase sequancer corrector with phase loss corrector system working on 415 Volt, 50 Hz, On/Off coil (switch) current capacity 18A, working voltage 12/24 Volt, Cut of voltage (Low) 330-370 (Adjustable), cut of voltage (High) 440-540 Voltage (Adjustable), Phase reversal System, Single phasing protection system, Time delay to start system 150 sec and Off switching time (two stop the system) 440 volt 50 Hz of capacity up to 30 HP including voltmeter and ammeter complete all as specified and as directed by Engr-in-Charge.

S&F in replacement unserviceable fully automatic star delta starter in sheet steel enclousure in door type,ML-2 FASD 3 phase phase sequancer corrector with phase loss corrector system working on 415 Volt, 50 Hz, On/Off coil (switch) current capacity 18A, working voltage 12/24 Volt, Cut of voltage (Low) 330-370 (Adjustable), cut of voltage (High) 440-540 Voltage (Adjustable), Phase reversal System, Single phasing protection system, Time delay to start system 150 sec and Off switching time (two stop the system) 440 volt 50 Hz of capacity up to 25 HP including voltmeter and ammeter complete all as specified and as directed by Engr-in-Charge.

Taking down existing old unsv LT panel & Supply, install, testing and commissioning of LT distribution panel, CPRI approved, weather/vermin proof, made out of 3mm thick CRCA sheet, factory assembled cubicle pattern modular and compartmentalized construction, outdoor type, with front and backside hinged double door with locking arrangement, floor mounted free standing type, duly powder coated, 3 phase and neutral 630 amps current carrying capacity aluminium bus bar with epoxy insulated coating with colour code and insulated support with aluminium earth bus of size 25x3mm with terminal switch, cable galleries, inter connecting bus bar connection/linkage, complete with the following switch gears and mounting the panel board on ground with PCC (1:2:4) type B-1 using 20mm graded stone aggregate bedding upto a height of 45 cm above gorund level, complete all as specified and directed by Engr-in-Charge and comprising the following :- (a) MCCB 4 Pole, 415 V, Adjustable type, 400 Amps with breaking capacity 36 KA- 01 No (In Coming). (b) MCCB 4 Pole, 415 V, Adjustable type, 250 Amps with breaking capacity 36 KA- 02 No (out Going) (c) MCCB 4 Pole, 415 V, Adjustable type, 200 Amps with breaking capacity 36 KA- 02 Nos ( Out going) (d) MCCB 4 Pole, 415 V,Adjustable type, 100 Amps with breaking capacity 36 KA- 04 ( Out going) (e) Digital Volt Meter 0-500V - 01 No. (f) Digital Ampere Meter 0-500 A with 3 Nos of CTs. (g) Indicator LED type

Supply, laying, jointing and testing XLPE insulated LT cable, 1100 volts grade (heavy duty) with stranded aluminium conductor, cross sectional area 95 Sqmm 3.5 core fixed along the poles or passing through pipes or laid under floors or through walls complete all as specified and as directed by Engr-in-Charge. Note (i) Earthwork, sand cushioning, brick protection and GI pipe to be measured and paid for separately under respective items.

All as per description of serial item No 38 here in before but cross sectional area 120 Sqmm 3½ core

S&F in replacement MCCB 350 Amp 4 pole 36 KA 415 Volt complete all as specified and directed by Engr-in-Charge.

S&F in replacement MCCB 200 Amp 4 pole 36 KA 415 Volt complete all as specified and directed by Engr-in-Charge.

S&F in replacement MCCB 250 Amp 4 pole 36 KA 415 Volt complete all as specified and directed by Engr-in-Charge.

S&F in replacement MCCB 160 Amp 4 pole 36 KA 415 Volt complete all as specified and directed by Engr-in-Charge.