Military Engineer Services Tender
If you want to inquire about any e-tender the Punjab government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder you will find every eprocurement Punjab tender on BidAssist.There is no need to enter all the details on the website of etender.up.nic.in as BidAssist helps you find the specific Punjab etender you're looking for. Read further to learn how to search and bid for etender Punjab.
Costs
EMD
₹ 12,00,000Document Cost
₹ 3,000Tender Fee
Refer Documents
Summary
Addn/altn Of 314 Jcos/or Md Accn Out Of 634 Jcos/or Md Accn
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_658918_1Bid Award Id
ViewTender No
CE BTZ/BTD/TOKEN - 02 OF 2024-25Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Taking down shutters only of any description area exceeding 1.0 sqm and not exceeding 2.0 sqm each and removing from site complete all as specified and as directed by Engineer-in- charge.
471
-
-
Supply and fixing factory made pressed steel frames of size 105 x 60mm (thickness of sheet shall be 1.25mm) for doors with one or more rebates including necessary lugs and lock strike plate, etc. and including fixing only butt hinges suitable Nos as directed for each leaf, and making good the wall with plaster in CM 1:6 complete all as specified and as directed by Engineer-in- charge.
Note : - Butt hinges shall be measured and paid separately under appropriate item of BOQ as supply only.
2380
-
-
Supply and fixing factory made pressed steel frames of size 125 x 60mm (thickness of sheet shall be 1.25mm) for doors with one or more rebates including necessary lugs and lock strike plate, etc. and including fixing only butt hinges suitable Nos as directed for each leaf, and making good the wall with plaster in CM 1:6 complete all as specified and as directed by Engineer-in- charge.
Note : - Butt hinges shall be measured and paid separately under appropriate item of BOQ as supply only.
3400
-
-
Material and labour for PCC (1:3:6) type C-1, using 20 mm graded aggregated as in back filling of pressed steel door frame/chowkhat and bed block for fixing of hold fast complete all as specified and as directed by Engineer-in-Charge
78
-
-
Supply & fixing factory made flush shutter 35mm thick, solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and as directed by Engineer-in- charge.
2495
-
-
Supply & fixing factory made gauged and skeleton shutter 35mm thick made out of 2nd class hard wood kiln seasoned and chemically pressure treated, open rebated and prepared to receive glass, gauze, etc., but divided into squares, with plain chamfered or rounded, mitred and rebated sash bars, any numbers, fitted with cut and mitred beads for securing glass, gauze etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); complete all as specified and as directed by Engineer-in- charge.
1460
-
-
Supply & fixing Fiber Glass Reinforced plastic (FRP) Door Frame of cross section 90mm x 45mm having single rebate of 32mm x 15mm to receive shutter of 30mm thickness. The laminate door frame moulded with two resistant grade unsaturated polyester plain and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete all as specified and as directed by Engineer-in- charge.
3015
-
-
Supply and fixing to existing door frames 30mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge.
855
-
-
Supply & fixing Rubber sheet 50mm wide and of thickeness not less than 3mm fixed with steel screws at the bottom of the door shutters complete all as specified and as directed by Engineer-in-Charge.
882
-
-
Supply and fixing 100mm long stainless steel butt hinges heavy duty type B-21 including steel screws for fixing complete all as specified and as directed by Engineer-in-charge.
1884
-
-
Supply only 100mm long MS butt hinges heavy duty type B-21 including steel screws complete all as specified and as directed by Engineer-in-charge.
9400
-
-
Supply and fixing anodised aluminium handle cast type 125mm long fixed with and including steel screws complete all as specified and as directed by Engineer-in-charge.
1256
-
-
Supply and fixing Extruded aluminium alloy handles, fabricated type, 150mm long fixed with and including steel screws complete all as specified and as directed by Engineer-in-charge.
4580
-
-
Supply and fixing aluminium anodised barrel tower bolt of extruded section, 150mm long fixed with and including steel screws complete all as specified and as directed by Engineer-in-charge.
1256
-
-
Supply and fixing aluminium anodised barrel tower bolt of extruded section, 200mm long fixed with and including steel screws complete all as specified and as directed by Engineer-in-charge.
4580
-
-
Supply & fixing aluminium anodised sliding door bolts 250mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed by Engineer-in- charge.
1302
-
-
Supply and fixing mild steel 300mm long rat tail rod pattern spring including roller and roller plate and fixing to frame fixed with and including steel screws complete all as specified and as directed by Engineer-in- charge.
674
-
-
Supply & fixing Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, Overall length of cover plate 150mm, complete all as specified and directed by Engineer-in-Charge.
2290
-
-
Supply & fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with screw in steel window (as shown in drawing) and with tinned tack nails and wooden bead in wooden shutter complete all as specified and as directed by Engineer-in- charge
2340
-
-
Supply & fixing 4mm thick sheet glass ordinary quality in squares / retangular not exceeding 0.5sqm in each pane and fixed with oil putty or as directed complete all as specified & directed by Engineer-in- charge.
1480
-
-
Supply & fixing 3mm thick figured glass pin head type in squares / retangular not exceeding 0.5sqm in each pane and fixed with oil putty or as directed complete all as specified & directed by Engineer-in- charge.
140
-
-
Supply & fixing 18mm thick single side prelaminated wood grain solid PVC sheet suitabley fixed as in cupboard shelves, partitions and similar work with 6mm PVC beading, support, screws, washer, plug etc including taking down old boarding any type and condition complete all as specified and as directed by Engineer-in-charge.
810
-
-
Supply & fixing factory made steel ventilator box type using ERW hollow 'P' section and double angle frame, with top hung shutter (glazed shutter, fly proof shutter and fixed glass) including fittings like hinges, tower bolt, stop legs, lug, handle, lock system etc. complete all as shown on drawing No BTD-903 Sheet No 1/2 and 2/2 or as directed by GE including fixing of lugs in PCC complete all as specified & directed. Note :- (i) The width /height as shown in drawing are tentative, however the same shall be adjusted as per actual opeining of vent. GE will approved the variation in the size of vent during execution at site (ii) Glass, wire mesh and painting shall be measured and paid separately under respective item of Sch (iii) Provision of all other items as shown & specified in on drawings and Provision of cutting holes of suitable depth in wall for inserting lugs etc including making good dismantled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate and cement mortar (1:3) shall be deemed to be include in quoted rates.
255
-
-
Supply & fixing factory made steel window box type with provision for cooler opening using ERW hollow 'P' section and double angle frame, with side hung shutters (glazed shutter, fly proof shutter, fixed glass and top hung glass shutter) including grill/guard bar of 8mm sq bar fixed horizontally @ 100 mm C/C complete including fittings like hinges, tower bolt, stop leg, lugs, handle, lock system etc. complete all as shown on drawing No BTD-903 Sheet No 1/2 and 2/2 or as directed by GE including fixing of lugs in PCC complete all as specified & directed. Note :- Note :- (i) The width /height as shown in drawing are tentative, however the same shall be adjusted as per actual opeining of window. GE will approved the variation in the size of window during execution at site. (ii) Glass, wire cloth and painting shall be measured and paid separately under respective item of Sch (iii) Provision of all other items as shown & specified in on drawings and Provision of cutting holes of suitable depth in wall for inserting lugs etc including making good dismantled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate and cement mortar (1:3) shall be deemed to be include in quoted rates.
750
-
-
Supply & fixing factory made steel window box type without provision for cooler opening using ERW hollow 'P' section and double angle frame, with side hung shutters (glazed shutter and fly proof shutter) including grill/guard bar of 8mm sq bar fixed horizontally @ 100 mm C/C complete including fittings like hinges, tower bolt, stop legs, lugs, handle, lock system etc. complete all as shown on drawing No BTD-903 Sheet No 1/2 and 2/2 or as directed by GE including fixing of lugs in PCC complete all as specified & directed. Note :- Note :- (i) The width /height as shown in drawing are tentative, however the same shall be adjusted as per actual opeining of window. GE will approved the variation in the size of window during execution at site. (ii) Glass, wire cloth and painting shall be measured and paid separately under respective item of Sch (iii) Provision of all other items as shown & specified in on drawings and Provision of cutting holes of suitable depth in wall for inserting lugs etc including making good dismantled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate and cement mortar (1:3) shall be deemed to be include in quoted rates.
1440
-
-
Material and labour for mild steel Framed work such as grills, ladder, cooler stand, cloth drying provision, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe-290 Gde E-165, complete including fabrication, welding work complete all as specified and as directed by Engineer-in- charge.
15150
-
-
Cutting holes exceeding half brick but not exceeding one brick in brick walls built in cement mortar for inserting angle iron for cooller stand or for similar work and making good dismantled portion in cement mortar (1:3) or cement concrete (1:2:4) type B-1 as required complete all as specified and directed by Engineer-in-Charge.
2512
-
-
Supply & fixing Factory made prefabricated Pressed steel cup board shutter with Door frame made out of mild steel 1.25mm thick, girth of frame 185mm including necessary MS rawl plug/bolts and fixing hinges as per manufactrurer instructions, shutter including stiffeners made out of mild steel sheet 1.25mm thick cut to size, holes punched and welded seams including bending or turning up all around, mitred angle etc as required, including Locking arrangement using mild steel mortise lock 4 levers of size 100mm (Make Godrej/Harison/Navtal) with 2 Nos of keys including MS chromium plated handle and 2 Nos MS locking rods out of 8 mm dia not exc 1000mm long fixed to mortise lock and handle with necessary bolts and nuts covered by MS sheet 1.25 mm thick complete including spray painting of synthetic enamel paint over a coat of zinc chromate primer on complete interior and exterior surface complete all as specified and as directed by Engineer-in-charge.
1000
-
-
Supply and fixing stainless steel curtain rod 25mm dia, wall thickness of pipe not less than 16 guage and grade SS 304, including brackets and pair of decorated end knobs (finials), stop roller etc. as per site requirement, fixed to wall with fixing accessories, including taking down old existing curtain rods any type or condition complete all as specified and as directed by Engineer-in-Charge.
3000
-
-
Material and labour for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment of soil under existing floors using emulsion @ one litre per hole, at 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed by Engineer-in-charge.
6330
-
-
Material and labour for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre 300mm apart including drilling depth of holes not less than 300mm and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed by Engineer-in-charge.
2990
-
-
Material and labour for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment of voids in masonry using chemical emulsion @ one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and as directed by Engineer-in-charge.
2370
-
-
Material and labour for hard core of broken stone or boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified & directed by Engineer-in- charge.
168
-
-
Material and labour for 75 mm thick PCC (1:3:6) type C-2 using 40mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement laid in anels including making joints 12mm wide to the full depth of PCC at the rate of 3.00 mtr centre to centre and at every turning point, filling the Joints with and including bitumen and sand (1:3) by weight complete all as specified and as directed by the Engineer-in-Charge.
2240
-
-
Roughening surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust etc. complete all as specified and as directed by Engineer-in-Charge.
12825
-
-
Demolition of floor hearth or wall tilling including cement mortar bedding/screed but not backing including removing rubbish material from building and thrown in low lying empty area at any distance exceeding 5 KM but not exceeding 10 KM from the site complete all as specified and as directed by Engineer-in-Charge
10370
-
-
Material and labour for Non Skid ceramic light coloured tiles 7 to 8 mm thick square or rectangular area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floor, tiles laid over and including 10mm thick bedding layer using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement complete all as specified and directed by Engineer-in-Charge.
11335
-
-
Material and labour for Non Skid ceramic light coloured tiles 7 to 8mm thick square or rectangular as in skirting (cut from same size and type as floor tile ), dado etc. set and jointed over and including 10mm thick bedding layer using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement including making good plaster surfaces (above skirting tile) to match the existing complete all as specified and as directed by Engineer-in-Charge.
1230
-
-
Material and labour for Non Skid ceramic light coloured tiles 7 to 8 mm thick square or rectangular area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed bed) in cement mortar (1:6) and finish the surface rough to receive the tile complete all as specified and directed by Engineer-in-Charge.
2070
-
-
Material and labour for Glazed ceramic coloured tiles light coloured of size 300mmx 450mm, 7 to 8mm thick, as in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick bedding layer (rendering) in cement mortar (1:4) and finish the surface rough to receive the tile complete all as specified and as directed by Engineer-in-Charge.
8300
-
-
Dismantling of Stone slabs of any description or thickness in floors, plateform, apron etc laid bedded and pointed in any mortar including removing rubbish material from building and thrown in low lying empty area at any distance exceeding 5 KM but not exceeding 10 KM from the site complete all as specified and as directed by Engineer-in-Charge.
96.5
-
-
Material and labour 16-18mm thickness approved shade granite of minimum size equal to width of slab, machine cut, granite duly factory grinding and polishing (table rubbed and mirror polished) and chamfering/rounding the outer edges, as in cooking platform, in steps, jambs, pillars, window-cills and like laid over and including 20mm thick cement mortar (1:4) screed bed including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including accomodate the hole for gas pipe complete all as specified and as directed by Engineer-in-Charge.
1520
-
-
Material and labour for machine cut 20mm thick (minimum), Kota stone slab (size of slab not less than 550x500mm for flooring and in single piece for treads of staircase, laid over and including 20 mm thick bedding layer in cement mortar (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing /grinding and polishing by machine, including machine cutting to make it square or rectangular as per site complete all as specified and as directed by Engineer-in-Charge.
1490
-
-
Material and labour for machine cut 15-18mm thick, Kota stone slab as in riser of steps, skirting, dado and on pillar, laid over and including 10 mm thick bedding layer in cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing /grinding and polishing by machine, including machine cutting to make it square or rectangular complete all as specified and as directed by Engineer-in-Charge.
135
-
-
Taking up or down existing galvanised steel water tubing (GI pipe) 15mm bore including fitting/connection from wall, ceiling, floor etc. complete all as specified and as directed by Engineer-in-charge.
3910
-
-
Supply and fixing galvanized steel tubing (GI pipe) medium grade 15mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling or laid in floor including cutting and threading of pipe complete all as specified and as directed by Engineer-in- charge. Note :- (i) Cost for cutting chases/groove as required for concealed pipe as directed shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account.
5000
-
-
Taking up or down existing galvanised steel water tubing (GI pipe) 20mm bore including fitting/connection from wall, ceiling, floor etc. complete all as specified and as directed by Engineer-in-charge.
12100
-
-
Re-fixing old serviceable 20mm bore galvanised steel water tubing (GI pipe) but new fittings like elbow, tee, union, socket, reducer etc. in new or old portion/position to walls, ceiling, floor etc complete all as specified and as directed by Engineer-in-charge.
Note :- (i) Old serviceable pipe obtained from taking up or down (here-in-before) item of this BOQ shall be reused after necessary cleaning internally and rerunning the old screw threads as required. (ii) Cost for cutting chases/groove as required for concealed pipe as directed shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account.
5760
-
-
Supply and fixing galvanized steel tubing (GI pipe) medium grade 20mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling or laid in floor including cutting and threading of pipe complete all as specified and as directed by Engineer-in- charge.
Note :- (i) Cost for cutting chases/groove as required for concealed pipe as directed shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account.
7608
-
-
Material & Labour for 40 mm GI pipe medium grade, made to shape as in spout pipe in sunken/ verandah/ Balcony including making hole and making good with cement mortar complete all as specified and as directed by Engineer-in-charge.
165
-
-
Supply & fixing rotational moulded polyethylene water storage tank white colour of capacity 500 litres (cylindrical vertical, three layered with closed top/lid), hoisted and fixed in position including making inlet and out let connection including dismantling/taking down of existing unserviceable PVC water storage tanks of any description and capicity with float valve and gate valve complete all as specified and as directed by Engineer-in-charge.
220
-
-
Disconnecting existing serviceable PVC tanks (OHT) of capacity upto 500 litre, setting aside or lowering for repairs, cleaning , etc. and hoisting if required, removing all scale and dirt from tanks and from mouths of circulating pipes and keep in safe custudy. After the building repair work or as directed reconnecting and re-fixing in original position including all inlet and outlet water connection (as per existing) complete all as specified and as directed by Engineer-in-charge. (Note : New ball valve (float valve) and gate valve shall be measured and paid separately under appropriate item of BOQ.)
94
-
-
Supply and fixing ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (polythene float) complete, screwed suitable for 20mm bore iron pipe complete all specified and as directed by Engineer-in-charge.
314
-
-
Supply and fixing in replacement gun metal, globe or gate valve (ISI marked), with iron wheel head, screwed both ends suitable for 20mm bore iron pipes complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of gate valve shall be as given in SSR or in relevant IS.
628
-
-
Supply and fixing in replacement bib tap with Wall Flange cast copper alloy, chromium plated, fancy type, long nose body, with round head/knob, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.
1256
-
-
Supply and fixing in replacement 15 mm bore chromium plated Angle stop valve with Wall Flange of cast copper alloy chromium plated, fancy type with round head/knob, half/full turn, screwed down high pressure screwed end for iron pipe or for unions and fixed complete all as specified and as directed by Engineer-in-charge.
Note :- The minimum weight shall be as given in SSR or in relevant IS.
942
-
-
Supply and fixing in replacement concealed stop cock cast copper alloy, chromium plated, fancy type, long shank and cup, screwed both ends suitable for 15mm bore iron pipe complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.
942
-
-
Supply & fixing in replacement cromium plated swivel shower rose of 125mm size with shower arm 195 mm long with bend of 45 degree with flange of any colour for fixing with 15mm dia pipe complete all as specified and as directed by Engineer-in-charge.
Note :- The minimum weight shall be as given in SSR or in relevant IS.
314
-
-
Supply and fixing in replacement central hole basin mixer valve with regular spout, 15mm bore, brass chromium plated, for mixing hot & cold water, complete with fittings, 450mm long braided hoses with connection and nut for WHB complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.
314
-
-
Supply and fixing bib tap with Wall Flange cast copper alloy, chromium plated, with round head/knob, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.
628
-
-
Supply and fixing 15 mm bore chromium plated Angular stop valve of cast copper alloy chromium plated, with round head/knob or half/full turn, screwed down high pressure screwed end for iron pipe or for unions and fixed complete all as specified and as directed by Engineer-in-charge.
Note :- The minimum weight shall be as given in SSR or in relevant IS.
628
-
-
Supply and fixing Kitchen Rack / Dish Rack (Kitchen Stand or wall mounted) of size 914mmx787mmx250mm (Appx size) made out of Food Grade Stainless Steel 0.6 mm thick sheet/strip including necessary arrangements for plates and utencils to keep (Holds up to many plates or bowls To accommodate several place settings, Multipurpose), stylish modern streamline design, rust resistant, easy to assemble and clean including fitting accessories complete all as directed by Engineer-in-charge.
314
-
-
Supply & fixing in replacement stainless steel sink made out of 1.00mm thick sheet , kitchen or laboratory with plugs, washers, waste coupling, waste pipe (flexible) 800mm long, including bedding in cement mortar to dwarf wall or fixing cast iron cantilever brackets and connecting union to waste pipe; overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-in-Charge.
314
-
-
Supply & fixing in replacement vitreous china wash basin, white, flat back of size 550mm x 400mm, including 32mm chromium plated waste coupling and PVC waste pipe (flexible) 600mm long including bracket and cutting for and pinning in end of bracket or erecting with long screwed shanks & fly-nuts, flange end bedded in red lead cement complete all as specified and as directed by Engineer-in-Charge.
314
-
-
Supply & fixing 600 mm long PVC connection 15mm size with PTMT nuts complete all as specified & directed by Engineer-in-charge.
1570
-
-
Supply & fixing in replacement brass chromium plated tubular towel rail 20mm dia 'D' type, 600mm long between flanges fixed to plug , bracket with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge.
314
-
-
Supply & fixing in replacement vitreous China squatting pan 'Orissa' pattern white of size 580mmx440mm white with integral foot rests, excluding flushing cistern, flush pipe above floor but including setting the trap and pan in lime concrete (1 lime, 2 sand or surkhi and 5 aggretate), min. 150mm thick all round and finished just below level of rim of pan to receive the floor finishing, including PVC flush pipe upto finished floor level, joints of flush pipe and trap make leakproof and testing upto entire satisfaction of Engineer-in-charge before filling concrete complete all as specified and as directed by Engineer-in- charge.
314
-
-
Supply and fixing in replacement PVC low level cistern of 10 ltrs capacity with top push button inclusive of brackets and PVC bend long type and connection to flush pipe of any size and pattern with inlet ball valve float and handle complete all as specified and directed by Engineer-in-Charge.
314
-
-
Supply and fixing chromium plated Soap Dish Holder with Round Flange, fixed on wall with chromium plated brass screws and PVC plug complete all as specified and as directed by Engineer-in-charge
628
-
-
Supply and fixing corner glass shelf of size 300x200mmx150mm, fancy type, toughened glass, with CP bracket and gurad railing, fixed along wall with CP brass screws and PVC plug complete all as directed by Engineer-in-charge.
314
-
-
Supply and fixing stainless steel peg set of six hooks and fixed in position with steel screws complete all as specified and as directed by Engineer-in-Charge.
942
-
-
Supply and fixing in replacement 600mm x 450mm size bevelled edge mirror of selected quality 5 to 6mm thick glass mounted on PVC sheet including fancy type PVC decorative beading and shall be fixed at wall with CP studs, complete all as specified and directed by Engineer-in-Charge.
314
-
-
Dismantling/taking up or down CI soil waste and vent pipe 100mm dia of any description from wall and taking out from trenches including all fittings (bend, trap, cowl, branch piece, reducer etc) and removing from the site complete all as directed by Engr-in-Charge.
530
-
-
Dismantling/taking up or down CI soil waste and vent pipe 75mm dia of any description from wall and taking out from trenches including all fittings (bend, trap, cowl, branch piece, reducer etc) and removing from the site complete all as directed by Engr-in-Charge.
515
-
-
Supply and fixing 100mm bore cast iron soil waste and vent pipe (spun pipe, confirming to IS 3989) in any length with or without ears, laid in trenches or under floor including all joints filled with lead complete all as specified and as directed by Engineer-in- charge. Note:- (i) Cost of material for run lead joints shall be included in the quoted rates nothing shall be paid extra on thic account (ii) Excavation and earthwork shall be measured and paid separately under respective item of Sch.
24
-
-
Supply and fixing 100mm bore cast iron soil waste and vent pipe (spun pipe, confirming to IS 3989) in any length with or without ears, fixed to wall with and including MS stack clamps (interval of 1m), nut and bolts of suitable size and securing ends of stays to wall and including PCC work for grouting, including all joints filled with and including lead complete all as specified and as directed by Engineer-in-charge.
Note:- (i) Cost of material for run lead joints shall be included in the quoted rates nothing shall be paid extra on thic account
450
-
-
Supply and fixing 50mm bore cast iron soil waste and vent pipe (spun cast pipe, confirming to IS 3989) in any length with or without ears, fixed to wall with and including MS stack clamps (interval of 1m), nut and bolts of suitable size and securing ends of stays to wall and including PCC work for grouting, including all joints filled with and including lead complete all as specified and as directed by Engineer-in-charge.
Note:- (i) Cost of material for run lead joints shall be included in the quoted rates nothing shall be paid extra on thic account
460
-
-
Supply and fixing 75mm bore cast iron soil waste and vent pipe (spun pipe, confirming to IS 3989) in any length with or without ears, laid in trenches or under floor including all joints filled with lead complete all as specified and as directed by Engineer-in- charge. Note:- (i) Cost of material for run lead joints shall be included in the quoted rates nothing shall be paid extra on thic account (ii) Excavation and earthwork shall be measured and paid separately under respective item of Sch.
100
-
-
Supply and fixing 75mm bore cast iron soil waste and vent pipe (spun pipe, confirming to IS 3989) in any length with or without ears, fixed to wall with and including MS stack clamps (interval of 1m), nut and bolts of suitable size and securing ends of stays to wall and including PCC work for grouting, including all joints filled with and including lead complete all as specified and as directed by Engineer-in-charge.
Note:- (i) Cost of material for run lead joints shall be included in the quoted rates nothing shall be paid extra on thic account
835
-
-
Supply & fixing 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed by Engineer-in- charge.
316
-
-
Supply & fixing 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed by Engineer-in- charge.
474
-
-
Supply & fixing 100mm bore CI branch pieces single (equal or unequal), ordinary or inverted (Spigot or socket type) complete all as specified and as directed by Engineer-in- charge.
316
-
-
Supply & fixing 75mm bore CI branch pieces single (equal or unequal), ordinary or inverted (Spigot or socket type) complete all as specified and as directed by Engineer-in- charge.
474
-
-
Supply and fixing in repair 100mm dia of long neck cast iron (spun) floor trap with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) using 20mm graded stone aggregate complete all as specified and as directed by Engineer-in- charge.
314
-
-
Supply and fixing in repair 75mm dia of long neck cast iron (spun) floor trap with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) using 20mm graded stone aggregate complete all as specified and as directed by Engineer-in- charge.
628
-
-
Supply & fixing cast iron reducer socket 100 to 50mm bore complete all as specified and as directed by Engineer-in- charge.
158
-
-
Supply & fixing cast iron cowl for 50mm bore pipe complete all as specified and as directed by Engineer-in- charge.
158
-
-
Supply and fixing 150mm x 150mm size salt glazed stone ware gully traps, square or round mouthed, type 'P' complete all as specified and as directed by Engineer-in- charge.
40
-
-
Demolition and breaking up drain pipes SGSW, AC or reinforced concrete pipe up to and including 150 mm bore pipes complete all as specified and directed by Engineer-in-Charge.
160
-
-
Material and labour for cement concrete (1:3:6), type C2 using 40mm graded stone aggregate as in bed of drain pipe of size 150mm bore (internal) including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed by Engineer-in- charge.
140
-
-
Material and labour for 150mm bore (internal dia) salt glazed stone ware (SGSW) drain pipe, grade ‘A’, laid on concrete bed to required slope in trenches, jointing with packed spun yarn and in cement and sand mortar (1:1) and tested complete all as specified and directed by Engineer-in-Charge. (Note : Excavation, earth work and concrete bed shall be measured and paid separately under appropriate item of BOQ.)
160
-
-
Material and labour cutting into existing manholes/septic tank for connecting new drain upto 150mm internal dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round to 3/4 section) in cement concrete (1:2:4) type B-1 smooth finished, and reforming benching as required complete all as specified & directed by Engineer-in-charge.
40
-
-
Supply and fixing SFRC (Steel fibre reinforced concrete) cover and frame (heavy duty HD-20 grade designation) Internal Size 590X590mm & External size of frame 800X800X100mm including Manhole cover having size 590X590X50mm thick and fixed over existing manhole after demolition of PCC coping & manhole Cover & set in CM 1:4 including PCC benching in (1:2:4) and finishing smooth complete all as specifed and directed.
40
-
-
Taking down eaves gutters and rain water PVC pipes ( any size or pattern) including all fittings, heads, shoes, bends, swan-neck etc ( measured overall as fixed along the centre line over fittings and accessories) including cleaning and stacking serviceable (good condition as directed by Engineer-in-charge) pipe for re use and balance removing from the site complete as specified and as directed by Engineer-in- charge
1925
-
-
Supply & fixing 110mm bore uPVC grade ‘A’ as per IS : 13592 pipes single socketed in any length with rubber ring joints for drain or rain water fixed along walls with and including PVC stack clamps (interval of 1m) of suitable size & nut bolts including PCC work for grouting and jointing material for joints, complete all as specified and as directed by Engineer-in- charge.
1925
-
-
Supply & fixing uPVC bends (any radius) suitable for 110mm bore pipe complete all as specified and as directed by Engineer-in- charge.
632
-
-
Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/ loose soil including cutting of grass, roots, bushes if any and filling of lower portion with soil obtained from cutting after sepration of grass, roots, bushes etc and dressing and removing from site all grass, roots complete all as specified and as directed by Engineer-in-Charge.
3250
-
-
Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundations, shafts, wells, cess pits, manholes, for taking out old pipe and laying new pipe line, for laying cable etc. not exceeding 10 Sqm on plan and getting out in soft/loose soil including trimming the sides and forming bottom surfaces to required levels complete all as specified and as directed by Engineer-in-charge.
3017
-
-
Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed.
2755
-
-
Removing excavated material (surplus soil) to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed by Engineer-in-charge.
262
-
-
Material and labour for 75mm thick cement concrete ( 1:4:8), type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and as directed by Engineer-in-charge.
3250
-
-
Supply and laying/fixing 60 mm thick (M35 grade) precast interlocking tile/paving block factory made chamfered edge (made by using PU moulds on Vibrating Table Machine) using cement concrete and pigment, prepolished & preglazed, with approved colour, design & pattern as in foot parth, parks, lawns, drive ways or light traffic parking etc., laid in required colour & pattern, over and including 25mm thick compacted bed of fine sand cushining, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand and complete all as specified and as directed by Engineer-in-Charge.
3250
-
-
Taking down cement or cement lime plaster from brick wall etc including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.
34435
-
-
Material and labour for rendering 15mm thick in cement mortar (1:6) on fair faces of Brick walls or concrete surfaces, finishing the surface fair and even complete all as specified and as directed by the Engineer-in-Charge.
16790
-
-
Material and labour for rendering 15mm thick in cement mortar (1:4) on otherthan fair faces of Brick walls or concrete surfaces, including mixing of liquid WPC in mortar @ as per manufacturer instruction per bag of cement of 50kg, finishing the surface fair and even complete all as specified and as directed by the Engineer-in-Charge. (Note :- WPC shall be measured & paid separately as Supply only)
14735
-
-
Material and labour for rendering 5mm thick in cement mortar (1:3) onconcrete surface of ceiling, finished fair, even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.
3400
-
-
Supply only liquid water proofing compound complete all as specified and as directed by the Engineer-in-Charge.
876
-
-
Dismantling of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, in any description including cleaning and stacking serviceable brick for re use and balance removing rubbish from the site complete all as specified and as directed by Engineer-in-charge.
168
-
-
Material and labour for brick work with sub class ‘B’ old size burnt clay bricks, straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge.
170
-
-
Material and labour for brick work in half brick thick wall straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-charge.
460
-
-
Demolition of cement concrete reinforced of any description such as slab/OHT staging slab, kitchen chimeny, chajjas, fins, shelves etc, including reinforcement cut as required to facilitate demolition and prepare the surface to casting/jointing new including removing rubbish material from building and thrown in low lying empty area at any distance exceeding 5 KM but not exceeding 10 KM from the site complete all as specified and as directed by Engineer-in-Charge
185
-
-
Material and labour for Providing precast cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in solid building blocks of size as directed suitable for OHT slab support etc and setting in mortar, complete all as specified and as directed by Engineer-in-Charge.
4
-
-
Material and labour for reinforced cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in kitchen sink slab etc of any section with plain fair faces including form work complete all as specified and as directed by Engineer - in - Charge.
(NOTE : Reinforcement shall be measured and paid for separately under appropriate item of BOQ.
12
-
-
Material and labour for reinforced cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in slabs for resting of water tank supported on walls/precast blocks, deck slabs and the like complete all as specified and as directed by Engineer-in-Charge.
(NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.
58
-
-
Material and labour for mild steel TMT bars 10mm dia & over cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.)
1000
-
-
Material and labour for mild steel TMT bars 6 to 8 mm dia cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.)
8000
-
-
Form work to soffits of suspended slabs such as flat roof slabs, floor slabs, shelf slab, landings and similar work not exceeding 200mm thick (horizontal or sloping) rough finished complete all as specified and as directed by Engineer-in- charge.
108
-
-
Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided including removing rubbish material from building and thrown in low lying empty area at any distance exceeding 5 KM but not exceeding 10 KM from the site complete all as specified and as directed by Engineer-in-Charge
70
-
-
Material and labour for Water proofing treatment to sunken slab and adjoining vertical surfaces complete all as directed by Engineer-in-Charge and specified as under:-
(a) Removal of loose concrete and cleaning the surface and and after proper cleaning, rendering 10 mm thick in cement mortar (1:3) using coarse sand including mixing of liquid WPC in mortar @ 200ml minimum per bag of cement of 50kg or as per manufacturer instruction, trowel even and smooth with steel trowel on sunken surfaces. (b) After rendering Applying first coat of chemical pidifin 2K(Dr Fixit) @ 0.86 Kg/Sqm (Minimum) as recommended by manufacturer.
(c) Provide a layer glass fibre mesh of size 2.25mm x2.25mm (45 GSM) over first coat of chemical Pidifin 2K as per manufacturers recommendation.
(d) Applying second coat of chemical Pidifin 2K (Dr Fixit) @ 0.86 Kg/Sqm (minimum) layer glass fibre mesh of size 2.25mm x 2.25mm (45 GSM) as recommended by manufacturers.
500
-
-
Material & Labour for PCC (1:5:10) type E2 using 40mm graded stone aggregate as filling of sunken floors complete all as specified and as directed by Engineer-in-charge.
70
-
-
Material and labour for covering the crumple joint between walls, beams, columns by 0.71 mm thick Plain Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) including fixing material and takig out old sheet any type complete all as specified and as directed.
140
-
-
Material and labour for Forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete with cement mortar (1:4) complete all as specified and as directed.
865
-
-
Carefully chipping, removing existing loose/ damaged concrete with plaster from Roof, Ceiling, Chajja, Fascia, Fins, Drops and similar items by low impact high frequency hammer/ chipper without damaging the existing sound concrete and exposing old reinforcement upto 10mm beyond corroded reinforcement bars using electrically operated diamond concrete saw blade, making the edges straight and even and cleaning it by wire brush and then by air blower complete all as specified and as directed by Engineer-in-charge.
5750
-
-
Cleaning all existing reinforcement bars in Roof, Ceiling, Chajja, Fascia, Fins, Drops and similar items with wire brush/rotary wire brush to make entire circumference surface of bars free from rust scales, loose material, dirt etc., complete and applying alkaline rust converting primer on the existing rebar and allowing it to react with rust for 6 hrs and form a corrosion resistant, insoluble and adherent protective layer including cleaning the reinforcement, wire brushing to remove the rust spalls, complete as per manufacturer’s instructions, complete all as specified and as directed by Engineer-in-charge.
Note :- Mode of measurement : per sqm of breaking area of concrete only.
Make:- Sika-Rust off 100 / Fosroc-ReebaklensRR / Asian SmartCare APCOREP RUSTREM/Pidilite Dr Fixit rust remover or Techno commercial equivalent in make mentioned in Appx 'B'
5750
-
-
Providing and application of Zinc rich epoxy anti-corrosive protective coating for reinforcement bars as corrosion protection system in 2 coats to the entire circumference surface of bars (consumption Qty as per manufacturer's instructions but min 0.4 kg/Sqm approx) in Roof, Ceiling, Chajja, Fascia, Fins, Drops and similar items complete all as specified and directed by Engr-in-charge. The product should confirm carbonation resistance of 2 mm and bond strength 1N/sqmm according to ASTM C 882-78 complete all as specified and as directed by Engineer-in-charge.
Note :- Mode of measurement: per sqm of application area of concrete.
Make:- Sika-Frizincr / Fosroc-Nito zinc primer / Asian SmartCare APCOREP RUSTCOAT RB / Pidilite Dr Fixit primer or Techno commercial equivalent in make mentioned in Appx 'B'
5750
-
-
Apply SBR based bonding agent to the entire concrete surface prior to building up of concrete with Polymer modified mortar / Micro concrete or any other treatment , including cleaning the surface to remove dirt, dust or any other impurities on the surface, etc. complete in Roof, Ceiling, Chajja, Fascia, Fins, Drops and similar items complete all as specified and as directed by Engineer-in-charge.
Make:- Sika- Latex SBR / Fosroc-Nitobond SBR Latex / Asian Smart Care Repair Polymer / Pidilite Dr Fixit Super latex or Techno commercial equivalent in make mentioned in Appx 'B'
3050
-
-
Rebuilding the section of structural damaged RCC/PCC elements of Roof, Ceiling, Chajja, Fascia, Fins, Drops repair to spalling concrete to its original size and shape in layers 20 mm average thickness by providing and applying with pre-batched, one component fiber based repair mortar having compressive strength = 30 N/sqmm (28 days) according to ASTM C 109; flexural strength = 3.5N/ sqmm (7 days) according to ASTM C 293-79 complete all as specified and as directed by Engineer-in-charge.
Make:- Sika-Monotop-122F / Fosroc-Renderoc HSXtra / Asian SmartCare Repair Mortar / Pidilite Dr Fixit Polymer mortar HB or Techno commercial equivalent in make mentioned in Appx 'B'
2950
-
-
Material and labour for removing loose disturbed or disintegrated old concrete surfaces of RCC beam, ceiling, slab, column, lintel, pardi, railing etc. cleaning thoroughly exposed reinforcement by sand blasting using suitable pump as directed by GE, preparing exposed concrete surfaces to receive guniting, applying one coat of anti-corrosive paint to the exposed reinforcement, supply and fixing welded wire mesh of size 100x100mm of 3mm dia wire and weight not less than 1.37 kg/Sqm and binding with 22 guage mild steel (annealed) binding wire to reinforcement and applying pressure guniting as per IS 6433 in cement mortar (1:3) average thickness 30mm and thereafter 10mm thick rendering in cement mortar (1:3) including mixing of liquid WPC in mortar @ as per manufacturer instruction and finishing the surfaces even and smooth without using extra cement to match the existing surface including removing rubbish material from building and thrown in low lying empty area at any distance out side MD land complete all as specified and as directed by Engineer-in-Charge.
Note :- (i) The finished level of the surfaces shall be matched with the existing surface. (ii) Provision of additional reinforcement steel in case required and ordered shall be measured and paid separately.
2700
-
-
Rebuilding the section of damaged RCC elements to its original size in thickness upto 100mm by supply and casting with ready to use non shrink, cementitious free flow micro-concrete having compressive strength greater than 30 N/sqmm (richer than M-30 grade) (28 days) according to ASTM C 1107-99, including mixing, placing and leveling the surface by grinding off cementitious slurry or cementitious joints differences if any and curing Including necessary formwork , Shuttering and jacating complete all as specified and as directed by Engineer-in-charge.
Note :- Mode of measurement: per KG of micro concrete.
Make:- Sika-Sikarep microcrete 4 / Fosroc-Renderoc RG / Asian SmartCare Micro Concrete HS / Pidilite Dr Fixit Micro concrete or Techno commercial equivalent in make mentioned in Appx 'B'
7500
-
-
Cutting chases, pinning in. making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for welded wire mesh, cutting not exc 10 cm girth in brick wall and making good, complete all as specified and as directed by the Engineer-in-Charge.
1000
-
-
Dismantling brick terracing tiles single layer from roof laid and pointed in cement mortar ncluding cleaning and stacking serviceable tiles for re use and balance unserviceable tiles removing from the site complete all as specified and as directed by Engineer-in-charge.
8650
-
-
Demolition/taking out of mud from roofs, any thickness, including removing / cutting uprooting grass, vegetations and roots of small plants etc on roof and surrounding/parapit wall etc, including removing rubbish material from building and thrown in low lying empty area at any distance exceeding 5 KM but not exceeding 10 KM from the site complete all as specified and as directed by Engineer-in-Charge
865
-
-
Material and labour for 40mm average thickness PCC padding in cement mortar (1:2:4) type B1 using 20mm graded stone aggregate on roof slab increasing uniformly towards ridges to obtain a chain slope 1:40, the top shall be trowelled and finishing the surface even amd smooth complete all as specified and directed by Engineer-in-Charge.
8650
-
-
Material and labour for 10mm thick rendering /screed in cement mortar (1:3) on roof top surface including mixing of liquid WPC in mortar @ as per manufacturer instruction per bag of cement of 50kg and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. (Note :- WPC shall be measured & paid separately as Supply only under relevant item of BOQ).
10000
-
-
Material and labour for cleaning the roof surface including flashing and junction of parapets etc. by brushing, removing all dust and applying evenly a tack coat of bitumen primer at the rate of 0.40 kg per Sqm complete all as specified and directed by Engineer-in-Charge.
10000
-
-
Material and labour for APP based polymeric membrane minimum weighing 3.80 kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced application, torching as recommended by the manufacturer with side over lap of 75mm and end over lap of 100mm, tucked into the chases on vertical surfaces complete all as specified and as directed by Engineer-in-charge.
10000
-
-
Material and labour for cool roof SRI tile with solar refractive index 78 of size 300x300mm, 8mm to 10mm thick shall be laid over 15mm thick screed bed in CM (1:4) mixed with liquid WPC @ as per manufacturer instruction per bag of cement of 50kg and including filling joints with white or coloured cement to match the shade of tiles complete all as specified and as directed by Engineer-in-Charge. (Note :- Water proofing compound shall be measured & paid separately as Supply only)
8650
-
-
Material and labour for making benching with PCC (1:2:4) type B0 using 12.5mm graded stone aggregate along side wall adjoining to roof in concave shape including mixing of liquid WPC in mortar @ 200ml minimum per bag of cement of 50kg or as per manufacturer instruction complete all as specified and directed by Engineer-in-Charge.
60
-
-
Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint (1st quality) of approved tint/colour over a coat of red oxide primer complete all as specified and as directed by Engineer-in- charge.
4225
-
-
Material and labour for Preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint (1st quality) of approved tint/colour over a coat of pink primer complete all as specified and as directed by Engineer-in- charge.
8120
-
-
Material and labour for Preparation of new plastered Internal wall surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:-
(a) Applying Wall care putty 2mm thick in two layers on complete surface and smoothening the surfcae with sand papers / by Mechanical method (hand electric grinder) prepatory to paint as directed. (b) Two coats of acrylic emulsion (interior) of approved tint/shade (Company Depot Tinted) over a coat of primer (interior) by using paint Roller.
13740
-
-
Material and labour for Preparation of new plastered external wall surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:-
(a) Applying Wall care putty 2mm thick in two layers on complete surface and smoothening the surfcae with sand papers / by Mechanical method (hand electric grinder) prepatory to paint as directed. (b) Two coats of acrylic emulsion (external) of approved tint/shade (Company Depot Tinted) over a coat of primer (external) by using paint Roller.
14735
-
-
Material and labour for Preparation of new plastered or concrete surface of wall surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:-
(a) Three coats of white wash by using paint brush.
3050
-
-
Material and labour for Preparation of new plastered or concrete surface of ceiling surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:-
(a) Three coats of white wash by using paint brush.
9150
-
-
Material and labour for complete removal of existing treatment on old ceiling surfaces of any desciption, preperation of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology, complete all as specified and as directed by Engineer-in- charge and applying the following:-
(a) Two coats of white wash by using paint brush.
7390
-
-
Material and labour for complete removal of existing treatment on Old internal wall surfaces of any desciption, preperation of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology, complete all as specified and as directed by Engineer-in- charge and applying the following:-
(a) Applying Wall care putty 2mm thick in two layers on complete surface and smoothening the surfcae with sand papers / by Mechanical method (hand electric grinder) prepatory to paint as directed. (b) Two coats of acrylic emulsion (interior) of approved tint/shade (Company Depot Tinted) over a coat of primer (interior) on old prepared surface by using paint Roller. Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible.
41198
-
-
E/M PORTION
-
-
-
Taking down carefully existing copper/aluminium point wiring (light/fan/sockets/bell/power point) complete with all accessories such as switch socket with sheet, ceiling rose, lamp holder including rusted/broken concealed conduit, junction and sunken boxes etc and removing dismantled material and making good disturbed surface of walls/floors etc matching with existing surface complete all as specified and as directed by Engineer-in-Charge.
5617
-
-
Material and labour for concealed Point wiring for one light point/fan point controlled by one switch (using red, black and green colour wires as colour coding) complete with 1.5 Sqmm (nominal cross section area) single core FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through and including PVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc., including Pressed steel powder coated sunken terminal box suitable for modular switch socket (Min 50mm deep and 1.6mm thick sheet, suitable size) concealed in wall, including inner and outer plates (cover plate white colour, any module as per requirements) suitable for fixing the modular switches/ socket / regulator etc, including provn of 1.5 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3) including fixing of switch/socket etc complete all as specified and as directed. (switch, socket shall be measured and paid separately under appropriate item of BOQ as supply only but cost of labour for fixing the same shall deemed to be included in the unit rate. ).
Note:- (i) Where ever it is not feasible to cable drawn through existing PVC conduit in roof slab (for ceiling fan point only) due to blocked, casing caping in lieu of pipe shall be provided by contractor without any extra cost, cost for the same shall deemed to be included in the quoted unit rate.
6027
-
-
All as per above Srl item No. 152 but for one socket out let 5/6 Amps point controlled by one switch (on same board) complete all as specified and as directed by Engineer-in-charge.(switch, socket shall be measured and paid separately under appropriate item of BOQ as supply only but cost of labour for fixing the same shall deemed to be included in the unit rate. ).
942
-
-
All as per above Srl item No. 152 but for one socket out let 5/6 Amps point controlled by one switch (on independent board and not below the any other switch board) complete all as specified and as directed by Engineer-in-charge. (switch, socket shall be measured and paid separately under appropriate item of BOQ as supply only but cost of labour for fixing the same shall deemed to be included in the unit rate. ).
988
-
-
All as per above Srl item No. 152 but for call bell point (on independent board) complete all as specified and as directed by Engineer-in-charge. (switches shall be measured and paid separately under appropriate item of BOQ as supply only but cost of labour for fixing the same shall deemed to be included in the unit rate. ).
314
-
-
Material and labour for concealed Point wiring for one light point controlled by two Nos- two way switch (using red, black and green colour wires as colour coding) complete with 1.5 Sqmm (nominal cross section area) single core FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through and including PVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc., including Pressed steel powder coated sunken terminal box suitable for modular switch socket (Min 50mm deep and 1.6mm thick sheet, suitable size ) concealed in wall, including inner and outer plates (cover plate white colour) suitable for fixing the modular switch, including provn of 1.5 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM(1:3), including fixing of switches complete all as specified and as directed. (switches shall be measured and paid separately under appropriate item of BOQ as supply only but cost of labour for fixing the same shall deemed to be included in the unit rate. ).
158
-
-
Material and labour for concealed Point wiring for one socket out let 15/16 Amps point controlled by one switch (on independant board) (using red, black and green colour wires as colour coding) complete with 2.5 Sqmm (nominal cross section area) single core FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through and including PVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc., including Pressed steel powder coated sunken terminal box suitable for modular switch socket (Min 50mm deep and 1.6mm thick sheet, suitable size ) concealed in wall, including inner and outer plates (cover plate white colour, any module as per requirements) suitable for fixing the modular switches / socket, including provn of 2.5 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3), including fixing of switch, socket complete all as specified and as directed. (switch, socket shall be measured and paid separately under appropriate item of BOQ as supply only but cost of labour for fixing the same shall deemed to be included in the unit rate).
1233
-
-
Material and labour for concealed Point wiring for one socket out let 20 Amps point controlled by one switch (on independant board) (using red, black and green colour wires as colour coding) complete with 4 Sqmm (nominal cross section area) single core FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through and including PVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc., including Pressed steel powder coated sunken terminal box suitable for modular switch socket (Min 50mm deep and 1.6mm thick sheet, suitable size ) concealed in wall, including inner and outer plates (cover plate white colour, any module as per requirements) suitable for fixing the modular switches / socket, including provn of 4 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3), including fixing of switch, socket complete all as specified and as directed. (switch, socket shall be measured and paid separately under appropriate item of BOQ as supply only but cost of labour for fixing the same shall deemed to be included in the unit rate).
23
-
-
Supply only modular switch 6Amps, single pole, one way (1 module) complete all as specified and as directed by Engineer-in-charge.
7957
-
-
Supply only modular switch 6Amps, single pole, two way (1 module) complete all as specified and as directed by Engineer-in-charge.
316
-
-
Supply only modular Bell Push switch, 6Amps, single pole, one way (1 module) complete all as specified and as directed by Engineer-in-charge.
314
-
-
Supply only modular switch 15/16Amps, single pole, one way (1 module) complete all as specified and as directed by Engineer-in-charge.
1233
-
-
Supply only modular switch 20Amps, single pole, one way (1 module) complete all as specified and as directed by Engineer-in-charge.
23
-
-
Supply only modular Socket outlet multipurpose type 6 Amp, flush type (2 module) complete all as specified and as directed by Engineer-in-charge.
1930
-
-
Supply only modular Socket outlet multipurpose type 15/16 Amp, flush type (2 module) complete all as specified and as directed by Engineer-in-charge.
1233
-
-
Supply only modular Socket outlet multipurpose type 20 Amp, flush type (2 module) complete all as specified and as directed by Engineer-in-charge.
23
-
-
Supply and fixing Ceiling Rose, polycarbonate, isolated body, surface bakelite 3 terminal, 240 volts, 5/6 Amp complete all as specified and as directed.
4530
-
-
Supply and fixing lamp holder (ISI marked) polycarbonate cased body (B22 base), top line series, with back plate, 6Amps, complete all as specified and directed by Engineer-in-Charge.
919
-
-
Supply and fixing LED lamp minimum 3 star rated 7W LED B-22 base complete all as specified and directed by Engr-in-Charge with following specifications
(a) Lumen system efficacy of lamp should be minimum 100 Lumen per watt.
(b) Input Voltage range : 140 to 270 volts
(c) Temp operating range : Minus 10°C to Plus 45°C
(d) Power factor : Minimum 0.95
(e) CRI : Morethan 80
919
-
-
Supply and fixing in replacement electric calling Bell Ding Dong type, AC 230 Volts single pole including making elctric connection complete all as specified and as directed by Engr-in-charge.
314
-
-
Supply and fixing in replacement (concealed flush to wall) factory made DB (made out of CRCA sheet not less than 1.2mm thick, fitted with DIN channel neutral link and 200 Amp rated bus bar) SPN, 12 Way 240V, suitable for mounting MCB/Isolator, conforming to IS-13032, DB shall be semi glosy finished with epoxy polyster based powder paint sprayed and backed at high temperature between powder paint process to ensure smooth finish and protection against corrosion atmosphere. The DB shall be double door type with hinged door with locking arrangement, the DBs shall be same make as MCBs, DB shall be provided with level marking indicating the incoming and outgoing circuits on always as specified. The DBs shall be of IP-43 protection class, including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge.
Note :- MCB’s shall be measured and paid separately under appropriate item of BOQ.
314
-
-
Supply and fixing in replacement (concealed flush to wall) factory made DB (made out of CRCA sheet not less than 1.2mm thick, fitted with DIN channel neutral link and 250 Amp rated bus bar) TPN, 4 Way, suitable for mounting Isolator/MCB, conforming to IS-13032, DB shall be semi glosy finished with epoxy polyster based powder paint sprayed and backed at high temperature between powder paint process to ensure smooth finish and protection against corrosion atmosphere. The DB shall be double door type with hinged door with locking arrangement, the DBs shall be same make as MCBs, DB shall be provided with level marking indicating the incoming and outgoing circuits on always as specified. The DBs shall be of IP-43 protection class, including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge.
Note :- MCB/ISOLATOR shall be measured and paid separately under appropriate item of BOQ.
79
-
-
Supply and fixing MCB ‘C’ curve suitable for 415 volts AC supply, 63 Amps, Four Pole with over load and short circuit protection and rupturing capacity not less than 10 KA, fixing in DB/panel complete all as specified and as directed by Engineer-in-charge
79
-
-
Supply and fixing MCB ‘B’ curve suitable for 230 volts AC supply, 32 Amps, Double Pole with over load and short circuit protection and rupturing capacity not less than 10 KA, fixing in DB/panel complete all as specified and as directed by Engineer-in-charge
316
-
-
Supply and fixing MCB ‘B’ curve suitable for 230 volts AC supply, 6 Amps, Double Pole with over load and short circuit protection and rupturing capacity not less than 10 KA, fixing in DB/panel complete all as specified and as directed by Engineer-in-charge
79
-
-
Supply and fixing RCBO for earth leakage, over load and short circuit protection 10 KA, suitable for 230 volts AC supply, 25-32 Amps, 30mA, Double Pole, fixing in DB/panel complete all as specified and as directed by Engineer-in-charge
314
-
-
Supply and fixing MCB ‘B’ curve suitable for 240 volts AC supply, 06 to 32 Amps, SP with over load and short circuit protection and rupturing capacity not less than 10 KA, fixing in DB/panel complete all as specified and as directed by Engineer-in-charge
3140
-
-
Disconnecting electric connection and taking down carefully serviceable geyser any capacity and keep in safe custudy. After the building repair work or as directed refixing /hanging the same including making all water connection with and including new PVC connection 15mm bore 600mm long heavy duty with brass nuts both side suitable for hot and cold water, including electric connection with and including three core PVC Insulated PVC Sheathed copper conductor flexible cable, hanging on wall with 04 No Nut bolts grouting in wall in PCC (1:2:4) using 12.5mm graded stone aggregate and making good the disturbed surface complete all as specified and as directed by Engineer-in-charge.
Note :- (i) GE Office name and Serial Number (already alloted ) of geyser shall be re written with red colour permanent marker, cost for the same shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account.
314
-
-
Disconnecting electric connection and taking down carefully serviceable electronic/electric energy meter single phase and keep in safe custudy and dismantling/taking out existing meter box any type. After the building repair work or as directed refixing the same electronic/electric energy meter in same qtr complete with accessories in and including new polycarbonate meter box with clearing transparent glass for taking reading, of suitable size for one No Single Phase Meter complete all as specified and directed by Engr-in-Charge.
Note :- (i) Refixing of Electric energy meter shall be done in such a way with sufficient space to house prepaid meters in future to be installed at later stage without any further modification all as per direction of Engineer-in-charge. (ii) Contractor shall maintain a register duly mentioned KWH meter Ser No for each Qtr and last meter reading and submit to the office of AGE E/M (North) store yard as per the direction of Engineer-charge.
314
-
-
Supply and fixing 6 Sqmm single core FRLSH PVC insulated unsheathed multistrand copper conductor cable drawn through and including PVC flexible pipe of suitable size for making incoming and outgoing connections of electronic/electric energy meter complete all as specified and directed by Engr-in-Charge.
1256
-
-
Disconnecting electric connection and taking down carefully old ceiling fans of any sweep complete with blades, nut bolts, rubber reel, capacitor 2.5mfd, canopies etc and shall be deposited in AGE E/M store yard complete all as specified and as directed by Engineer-in-charge.
651
-
-
Supply and hanging /fixing ceiling fan 1200 mm sweep AC Supply (Input Voltage Range ; 120 to 280V), BLDC type, 5 star rated, BEE and ISI Marked super enamelled, copper winding of 'B' class insulation, single phase, maximum 30W (± 10%), Temperature rise 40 degree maximum without remote with and including capacitive regulator, 03 No blades, down rod including accessories, white colour, total harmonic less than 10%, 5 speed, hanging in position including making connection with flexible cord three core twisted copper conductor of suitable size from ceiling rose to fan complete all as specified.
Note :- (i) Serial Number as issued by Engr-In-Charge of celing fan and GE Office name shall also be written on fan with red colour permanent marker and fixing of regulator on switch board, cost for the same shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account
965
-
-
Supply and fixing exhaust fan (heavy duty) steel body, AC single Phase 230V, 50Hz, 900RPM, size 300mm sweep with blades and including new mosquito stainless steel wire mesh of guage 0.36mm with suitable wooden frame protection against birds etc mounted in suitable opening arrangement in wall and electric connection with and including three core PVC Insulated PVC Sheathed copper conductor flexible cable 24/0.2mm drawn in flexible PVC conduit and hanging on wall with 4 Nos steel fastners 10mm dia 100mm long and making good the disturbed surface complete all as specified and as directed by Engineer-in-charge.
Note :- (i) Serial Number as issued by Engr-In-Charge of fan and GE Office name shall also be written on fan with red colour permanent marker, cost for the same shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account (ii) Cost for making suitable cutting/opening in wall for fixing of exhaust fan including making good disturbed surface and masonary work shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account.
314
-
-
Supply and fixing ventilating Air fresher Fan of size 250mm sweep, single phase, 1200RPM, copper winding, made of sturdy Engineering plastic body complete with louvers shutter, including provision of cutting of wall for suitable opening as per fan and making good the disturbed surface as per existing, including electric connection with and including new 1 Sqmm, 2 core flexible copper conductor cable from ceiling rose to fan including fixing material complete all as specified and as directed by Engineer-in-charge.
Note :- (i) Serial Number as issued by Engr-In-Charge of Air fresher Fan and GE Office name shall also be written on Air fresher Fan with red colour permanent marker, cost for the same shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account.
314
-
-
Disconnecting electric connection and taking down tube light/bulk head fitting etc any type complete all as specified and as directed by Engineer-in-charge.
2111
-
-
Supply and fixing LED tube light fitting polycarbonate housing 1 x 18/20 Watt, appx 4 feet long, with decorative box linear, housing environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to tube fitting, complete fitting with all accessories and following specifications, complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 110 Lumen per watt. (b) Input Voltage range : 140 to 270 volts. (c) Temp operating range : Minus 5°C to Plus 45°C (d) Power factor : Minimum 0.95 (e) THD : Current THD Max10% and voltage THD max 5% (f) IP rating : IP-20. (g) LED Driver of the same make as of the luminaire. (h) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (j) Surge protection minimum 2.5 kV. (k) CCT : Minimum 6000K (l) CRI : Minimum 80 (m) Rated life time : 50000 burning hrs @L70 (Average 10 to 12 hrs daily)
1460
-
-
Supply and fixing LED light fitting 1 x 8/10 Watt, appx 2 feet long with decorative ultra ceiling square profile linear LED lighting fixture with extruded polycarbonate environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to light fitting, complete fitting with all accessories and following specifications, complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 5°C to Plus 45°C (d) Power factor : Minimum 0.95 (e) THD : Current THD Max10% and voltage THD max 5% (f) IP rating : IP-20. (g) CRCA pre coated housing with plastic end cap. (h) LED Driver of the same make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection minimum 2.5 kV. (l) CCT : Minimum 6000K (m) CRI : Minimum 80 (n) Rated life time : 50000 burning hrs @L70 (Average 10 to 12 hrs daily)
674
-
-
Supply and fixing LED Bulkhead fitting 1 x 9/10 Watt, complete with Standard LED lighting fixture with extruded polycarbonate housing environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to light fitting, complete fitting with all accessories and following specifications complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 5°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : 15%. (f) IP rating : IP-65. (g) CCT : Minimum 5400K (h) Polycarbonate housing white coloured (j) LED Driver of the same make as of the luminaire. (k) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (l) Surge protection minimum 2.5 kV. (m) CRI : Minimum 80 (n) Rated life time : 50000 burning hrs @L70 (Average 10 to 12 hrs daily)
314
-
-
Supply and fixing energy efficient LED security light fitting of 35W pressure die cast aluminium housing/body, heat resistant clear toughened glass, better optics for uniform distribution street luminaire, with driver, including electric connection with using 3 core flexible copper conductor cable 1.5Sqmm from ceiling rose to light fitting, fixing the light fitting with new bracket made out of GI tubing light grade 25mm dia, 1.2 metre long bent to shape at 120 degree angle at half metre from bottom, including two Nos clamps made out of MS Flat iron size 25x3 mm with suitable nuts and bolts for fixing of bracket along wall including painting to MS clamp and nut bolts with two coats of aluminium paint over a coat of red oxide primer, complete fitting with all accessories and following specifications, including taking down old unserviceable light fitting any type with bracket complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 110 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : Max10%. (f) IP rating : IP66. (g) IK rating : Minimum IK07 (h) Built in potted LED Driver of the make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection 10 kV (inbuilt + extended) (l) CCT : 5700 K. (m) CRI : Minimum 70 (n) Lens - High Efficiency wide angle lens. (o) BIS Approved fixtures and driver (p) Rated life time : 50000 burning hrs @L70 (Average 10 to 12 hrs daily)
152
-
-
Taking out old sub main wiring of any conductor any size from conduit and taking down old unserviceable conduit with fittings, and making good disturbed surfaces of walls as per original complete all as specified and as directed by Engineer-in-Charge.
6200
-
-
Material and labour for concealed sub main wiring (using colour coding such as red, black, white, green colour or as directed) with 6 Sqmm single core (03 run i.e 2 runs for main phase and neutral, 01 run for continues as earth wire) FRLSH PVC insulated unsheathed multistrand copper conductor cable drawn through and including PVC conduit 25mm dia (medium quality ISI marked), for independent circuit including all fitting arrangement i.e. PVC clamp, rawl plug, screw, PVC junction box, tee, bend etc. and including cutting of chases in wall and making good disturbed surfaces of walls as per original complete all as specified and as directed.
Note :- Three runs of copper conductor cable and one run of PVC conduit including accessories shall be measured and paid as one unit (one RM length) for payment and extra length of cables required for connection to MCBs/DB shall not be measured and the cost for the same shall deemed to be included in the unit rate.
6200
-
-
Dismantling/Taking out old unserviceable earthing system and connected earth wie complete all as specified and as directed by Engineer-in-charge.
79
-
-
Material and labour for Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI earthing wire 4 mm dia by means of GI bolts/nuts/washers and protected by 15 mm bore GI light grade pipe upto test point or upto main switch board, fixing with 02 Nos nuts and bolts. Earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common salt all around bottom and top. 20 mm bore GI medium grade pipe for watering and including funnel, wire mesh, PCC chamber pit made with PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) including necessary form work, excavation and earth work in any type of soil, returning filling and disposal of surplus soil to a distance not exceeding 50m, Pit cover 40mm thick made with RCC (1:2:4) type B1 (using 20 mm graded stone aggregate) including TMT reinforcement 8mm dia @ 75mm c/c both way, MS handle 12mm dia, cover rest on MS angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified & shown in electrical plate No. 3 of SSR 2009 (Part-I) complete all as specified and as directed by Engineer-in-charge.
Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) Protection pipe and GI earthing wire upto test point or upto electric equipment from top of earth plate shall be included in the unit rate of this item. (iii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge.
158
-
-
Dismantling/taking up or down CI/DI/PVC pipe of size 100/110mm bore including fittings from trenches/under road/under hardstanding including balling out dirt/muddy water if necessary complete all as directed by Engr-in-Charge.
Note : (i) Excavation and Earth work shall be measured and paid separetly under respective item of BOQ
1840
-
-
Dismantling/taking up or down CI/DI/PVC pipe of size 75/80/90mm bore including fittings from trenches/under road/under hardstanding including balling out dirt/muddy water if necessary complete all as directed by Engr-in-Charge.
Note : (i) Excavation and Earth work shall be measured and paid separetly under respective item of BOQ
1580
-
-
Supplying, laying, jointing and testing Ductile iron pipe (ISI marked) class K-7, bore 100mm, confirming to IS : 8329-2K, spigot & socketed ends centrifugally cast, with cement mortar lining inside and metallic zinc coating with finishing layer of bituminous paint on outside the pipe, suitable for and including rubber tyton joints (Push-on joint) complete all as specified and as directed.
Note : (i) Earth work, DI specials/ fittings shall be measured and paid separetly under respective item of BOQ. (ii) Test Certificate for pipes from manufacturer shall be produced. No payment shall be entertained without Test Certificate.
1840
-
-
Supply, laying, jointing and testing of galvanized steel water tubing 80 mm bore ISI marked medium grade including fittings Viz Tees, Socket, bends, elbows, union nipple etc screwed and socketed joint laid in trenches /under road including cutting and threading of pipe as required complete all as specified and as directed by Engineer-in- charge.
(Note:- Excavation and Earth work shall be measured and paid separately under respective item of BOQ)
1580
-
-
Dismantling/taking up or down GI pipe of size 50mm bore including fittings from trenches/under road/under hardstanding including balling out dirt/muddy water if necessary complete all as directed by Engr-in-Charge.
Note : (i) Excavation and Earth work shall be measured and paid separetly under respective item of BOQ
882
-
-
Dismantling/taking up or down GI pipe of size 25mm bore including fittings from wall, ceiling/roof, floor, trenches etc complete all as directed by Engr-in-Charge.
Note : (i) Excavation and Earth work if required shall be measured and paid separetly under respective item of BOQ.
2484
-
-
Supply, laying, jointing and testing of galvanized steel water tubing 50 mm bore ISI marked medium grade including fittings Viz Tees, Socket, bends, elbows, union nipple etc screwed and socketed joint laid in trenches /under road/floor etc including cutting and threading of pipe as required complete all as specified and as directed by Engineer-in- charge.
(Note:- Excavation and Earth work shall be measured and paid separately under respective item of BOQ)
882
-
-
Supply, laying, jointing and testing of galvanized steel water tubing 25 mm bore ISI marked medium grade including fittings Viz Tees, Socket, bends, elbows, union nipple etc screwed and socketed joint laid in trenches /under road/floor/along wall etc including cutting and threading of pipe as required complete all as specified and as directed by Engineer-in- charge.
(Note:- Excavation and Earth work if required shall be measured and paid separately under respective item of BOQ)
2284
-
-
Material and labour for lead joints to cast iron pipes of 100mm bore and fittings complete all as specified and as directed by Engineer-in- charge.
10
-
-
Supply and fixing in replacement cast iron sluice valve 100 mm dia with flanged ends class PN 1.6 (ISI marked) confirming to IS:14846-2000, drilled type, steel spindle, CI gate with brass ring, iron wheel handle, suitable for CI/DI pipe line, complete including jointing material such as nuts, bolts, washers and rubber sheet insertion 3.0mm thick at both ends etc including taking out old sulice valve complete all as specified and as directed.
10
-
-
Supply and fixing in replacement cast iron sluice valve 80 mm dia with flanged ends class PN 1.6 (ISI marked) confirming to IS:14846-2000, drilled type, steel spindle, CI gate with brass ring, iron wheel handle, suitable for CI/DI pipe line, complete including jointing material such as nuts, bolts, washers and rubber sheet insertion 3.0mm thick at both ends etc including taking out old sulice valve complete all as specified and as directed.
5
-
-
Supply and fixing in replacement gun metal, globe or gate valve (ISI marked), with iron wheel head, screwed both ends suitable for 50mm bore iron pipes complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of gate valve shall be as given in SSR or in relevant IS.
31
-
-
Supply and fixing DI special fitting suitable for 80 to 300 mm bore pipe line, for reducing/bends (any type radius and angle) tapers any type, straight, bend, increasing decreasing or double socket extra Tee pieces single branch Y 'Junction' double branch cross collers cap etc including taking out old fittings complete all as specified and as directed.
Note:- Make of DI fittings shall be same make as DI pipe or as per recommendation of DI pipe manufacturer.
2500
-
-
Supply and fixing in replacement cast iron double air relase valve isolating type (ISI marked), flanged type and drilled, confirming to IS-14845, PN10, suitable for 50mm bore pipe including jointing material such as nuts, bolts, washers and rubber sheet insertion 3.0mm thick at both ends etc including taking out old valve complete all as specified and as directed.
2
-
-
Material and labour for Construction of brick masonary valve pit chamber size 120 X120 X120 cm (internal dimension) using sub class 'B' bricks complete, PCC (1:3:6) type C-2 using 40 mm graded stone aggregate as in foundation, coping on top in PCC (1:2:4) type B-1 using 20 mm graded stone aggregate, brick work in cement mortar (1:4), inner plaster 12 mm thick in cm (1:3) finished even and smooth and pionting flush externally as the work proceeds in the same mortar, MS sheet cover 3.15mm thick mounted on angle iron frame of size 40 x 40 x 6mm with handle and locking arrangement duly painted with two coats of synthetic enamel paint over a coat of red oxide primer and embeded portion of MS work duly applying black bitumenous paint before embeded including as per site requirement excavation & earth work, returning fillig and disposal of surplus soil to distance not exceeding 50m and deposited where directed, and including demolition old valve pit complete all as specified and as directed by Engineer-in-charge.
Note :- Valve pit shall be constructed all as shown on drawing No BTD-811 Sheet No 1/2 and 2/2 and as per above specified specifications.
10
-
-
Material and labour for Construction of brick masonary valve pit chamber size 75 X75 X75 cm (internal dimension) using sub class 'B' bricks complete, PCC (1:3:6) type C-2 using 40 mm graded stone aggregate as in foundation, coping on top in PCC (1:2:4) type B-1 using 20 mm graded stone aggregate, brick work in cement mortar (1:4), inner plaster 12 mm thick in cm (1:3) finished even and smooth and pionting flush externally as the work proceeds in the same mortar, MS sheet cover 3.15mm thick mounted on angle iron frame of size 40 x 40 x 6mm with handle and locking arrangement duly painted with two coats of synthetic enamel paint over a coat of red oxide primer and embeded portion of MS work duly applying black bitumenous paint before embeded including as per site requirement excavation & earth work, returning fillig and disposal of surplus soil to distance not exceeding 50m and deposited where directed, and including demolition old valve pit complete all as specified and as directed by Engineer-in-charge.
Note :- Valve pit shall be constructed all as shown on drawing No BTD-811 Sheet No 1/2 and 2/2 and as per above specified specifications.
36
-
-
Material and labour PCC (1:2:4) type B1 using 20mm graded stone aggregate including form work for thrust block complete all as specified and directed by Engineer-in-Charge.
5
-
-
Material and labour for boring of holes under road pavement, hard standing or any other situation by manual mean (trenchless boring) for accommodate/inserting pipe upto 100mm bore in the drilled holes, including returning, filling in the end working space including removal of surplus soil and making good the surface complete all as specified and as directed.
Note ; (i) Only length of the road/hard standing/Pavement will be measured for payment and cost for excavation, returning filling and making good at both side of bore shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account.
(ii) Pipe shall be measured and paid separately)
300
-
-
Material and labour for connection from existing main water supply pipe line including ferrule, MS clamp, nut bolts and accessories for providing of connection complete all as specified and as directed.
500
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements