Odisha Lift Irrigation Corporation Limited Tender
... More
Search from a pool of business opportunities related to Odisha tenders on the online platform of BidAssist. Be it an Odisha PWD tender or a civil aviation tender, one can find every tender Odisha government, as well as PSUs and other organizations, post online. Every tender, active or achieved, is sourced from the eProcurement Odisha website and thus carries full credibility.
Costs
EMD
₹ 14,383Document Cost
₹ 6,000Tender Fee
Refer Documents
Summary
Revival Of Bankili Rl Under Kolanara Block Of Rayagada District
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2025_OLIC_111861_27Tender No
02/2024-25Tender Authority
Odisha Lift Irrigation Corporation Limited ViewPurchaser Address
-Website
http://http://www.odishalift.co.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
... More
Cement concrete (1:2:4) for R.C.C. with 12mm size black h.g.c.b. chips of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc complete as per the direction of the Engineer-incharge.
6.3
7928
49951.69
... More
Brick work with C.B. Brick 25cm x 12cm x 8cm size having crushing strength not less than 75kg / cm2 with dimensional tolerrance + 8% in cement mortar (1:6) in foundation & plinth etc. complete as per the Engineer-incharge.
8.92
5685
50717.25
... More
12mm cement plaster in cement mortar (1:6) finished smooth to brick work after racking out joints including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge.
134.42
191
25736.05
... More
Rigid smooth centering & shuttering for R.C.C. works including false work & dismateling then after including cost of materials in ground floor complete an directed by the Engineer-incharge.
74.36
571
42473.69
... More
Labour charge for M.S. reinforcement for R.C.C. work including cutting, bending & typing the grills & placing in position including cost of binding wire 18 to 20 guage per Qntl. Including cost of HYSD Still Bar (FE 415/ FE 500)
5.48
9542
52294.11
... More
Cement punning over plastering including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge.
30.36
39
1210.45
... More
Filling the foundation and plinth with excavated material as directed by the Engineer-incharge.
352.08
150
52988.04
... More
White washing 3 coat with approve good stone lime including cost conveyance charges of materials including supply of labour, gum, indigo etc. required for the work complete as directed by the Engineer-incharge.
110.24
21
2343.7
... More
Colour Washing 3 coats with shell lime and colouring materials
16.44
46
757.39
... More
Painting of red oxide primer of approved quality for priming over iron work including cost taxes etc. complete as per the direction of the Engineer-incharge.
9.26
182
1685.32
... More
MS Pannel Door double leafed with MS frame overall size including frame of height 1.2mt x 1.98mt. width for door and shutter of 20 gauge CR sheet pannel as per approved size & specification etc. complete including cost of all materials fitting and fixing the door etc. complete as per the direction of the Engineer-incharge.
100
70
7000
... More
Cost of 0.90 X 1.37 Mt. iron Gate including fitting & transportation
1
5500
5500
... More
Spreading of 20 mm.size hg metal and sand inside the electrical sub-station boundary
1
2500
2500
... More
Labour Charges for fixing M.S. Door, Window, ventilators in position
1
1000
1000
... More
Writing charge of required information and data on both side of the transperancy pillar including supplying of approved paints and required material for writing etc. complete as per the direction of the Engineer-incharge.
1
1000
1000
... More
Fitting of un plasticised 200mm dia PVC Pipe for following inside dia mtr. for all classes of pipe including jointing the pipe with solvent cement by non-head application method including fitting and fixing of required no. of PVC Tee for outlet and PVC Shaddle and PVC Riser nipple for fitting air valve, equal Tee etc. complete including conveyance pipe from village to worksite and testing of pipe line etc. complete as per the direction of the Engineer-incharge.
438
162
71280.12
... More
Labour charges for installation of 10/12.5/15HP Motor including fitting & fixing of base frame, fitting & fixing suction and delivery pipe to motor, NR Valve, Foot Valve, Sluice Valve and other fitting materials including cutting, welding etc. complete as per the direction of the Engineer-incharge.
1
12806
12806.4
... More
Transportation charges of materials including loading, unloading and stacking properly as per the direction of the Engineer-incharge.
1
354
354.38
... More
Construction of outlet at Tank
4
500
2000
... More
Welding, laying and fitting of 150 mm Ø G.I. pipe
90
627
56430
... More
Monoblock pump set total head of 26 mtrs capable to discharge 1700 LPM with 15HP/11.20 KW squirrel cage induction motor fitted with bronze impeller TB-2 of IS 318/1981, companion flanges & Class "F"insulation suitable for operation 415 volt +6%-15% 3 phase, 50Hz AC poweer supply suction/deliveery = 100mmx100mm with BEE Star rated energy efficiency Pump & as per IS-9079/2002 with overall efficiency 62 to 65% of reputed brand having wide dealership net work for easy availability of spares.
1
49007
49007
... More
Automatic Star Delta BCH make starter sheet steel enclosure suitable for operation of squirrel cage induction motor upto 10/15 HP with 16 Amp (AC-3) contactor at 415 volt +6% - 15%, 3 phase, 50 Hz, AC supply with suitable overload relay & No volt coil with electric pnemutic timer suitable for operation at voltage range of 300-440 volt including cost of transportation to site. The starter should provide dependable protection against overload and single phasing & should be of reputed brand having wide dealership network for easy availability of spares.
1
6888
6888
... More
Supplying 63 Amp. 415 volt T.P.Main Switch confirming to IS-4064 (PT-I & PT-II) with utilisation category AC-22 including all taxes etc.
1
3141
3141
... More
3 x 16 sqmm Tarpodar cable XLPE (Cross link polyethylin) conforming to IS: 7098 (Part-II) including laying below .9mtr. of the ground and filling the excavated materials including watering and ramming.
30
116
3480
... More
Base frame for panel (size 0.40mx0.20m) made with 3" size M.S. channel having suitable holes for fitting of panel Board, coloured with one coat of red oxide primer and two coats of smokes grey enamel paint & Base frame for motor (size 0.50mx0.27m) made with 3" size M.S. channel having suitable holes for fittings of different size and make 3 phase centrifugal monoblock pump set from 10 H.P. to 15 H.P. coloured with one coat of red oxide primer & two coats of smoke grey enamel paint.
1
1004
1004
... More
Motor hood size (0.45mx0.45mx0.60m) made with 18 SWG (cold rolled M.S.Sheet with one coat of red oxide primer and two coats of smoke gray / navey blue enamel n both side (inside & outside) suitable to cover centrifugal monoblock Pump Set from 10 HP to 15 HP and having provision for attachement with the groves on rear side of the pannel board.
1
993
993
... More
100 mm dia G.I. bend IS No.1239(Part-II/1992)
5
827
4135
... More
100 mm dia G.I. flange IS No.6392 / 1971
12
436
5232
... More
150 mm dia G.I. flange IS No.6392 / 1971
15
696
10440
... More
100 mm Ø nominal bore G.I. pipe having wall thickness 4.5 mm electrical resistance welded of medium class confirming to IS - 1239 (pt-1 of 2004) with socketed at one end and the other end protected with plastic thread protector. The socket confirming to IS-1239 (pt-II/1992) with latest amendmewnts in random length of 4 to 7 mtrs. Each pipe should bear ISI certification & manufacturers name / Trade mark.
18
1237
22266
... More
200 mmx100 mm G.I./M.S. Reducer
1
417
417
... More
Cost of 100mm dia C.I.Foot valve
1
1159
1159
... More
100mm Non-return valve C I double flanged swing type PN - 1.0 as per IS:5312 part-I with by-pass arrangement
1
6082
6082
... More
50 mm Ø Air release valve with saddle & Raiser pipe. The air release valve shall confirm to IS 14845 with ISI mark.
2
7520
15040
... More
Supplying of Rigid UPVC Pipe of 200mm dia ivory grey having specific gravity of 1.4 to 1.46 Gm./CC of straight length of 6mtr. For portable water supplies specification bearing ISI mark for working pressure of 2.5kgf/cm2 as per latest amendent of IS 4985 including cost of couple for plain ended pipes of one end plain & other bell ended. The pipe should be clearly & indelible marked ink or stenciled confirming to IS 4985/2000 withy CIPET certificate(Pre-CIPET Test & Post CIPET Test).
438
326
142788
... More
200 mm x200 mm x200 mm Ø PVC Equal Tee (W.P. 4 kgf/cm2) confirming to IS-4995/1988 with latest ammendment
3
907
2721
... More
200X200X100mm dia M.S outlet Tee made with 201mm ID and 216 mm OD M.S Pipe of 8mm thick 400mm long fitted with 1 mtr long 100mm dia M.S.Pipe welded with 2 nos of 100mm dia M.S.Flange in between the 1 mtr M.S.Pipe and 0.25 mtr long 100 mm dia M.S.Pipe fitted horizentally with 2 mtrs of 100mm dia M.S.Elbow with water locking arrangement made out of 1 no. of 100mm dia open flange and 1 no. of 100mm dia blind flange and with hinges gaskets arrangement that UPVC pipe should be inserted directly 100mm long inside the 151mm dia ID M.S.Pipe at the both ends painted with two coats of anti corosive paints in complete set.
4
4775
19100
... More
200 mm Ø PVC coupler (4 kg/cm2) Agricultural PVC fittings confirming to IS-4995/1988 with latest ammendment
4
284
1136
... More
200 mm Ø PVC End Cap (W.P. 10 kgf/cm2) confirming to IS-4995/1988 with latest ammendment
4
297
1188
... More
Supply of solvent cement of approve quality for joiniting of PVC Pipe with all cost and all tax etc. complete as per the direction of the Engineer-incharge.
10
321
3210
... More
5/8 ' x3" Nut bolt F.T. as per IS specification
25
94
2350
... More
⅛" thick Rubber Insertion as per IS specification
25
58
1450
... More
5/8 ' x12" Nut bolt & washer F.T. for foundation
5
94
470
... More
4 mm 2 PVC single core copper wire
24
40
960
... More
Fitting fixing of 200×200×200mm. PVC equal Tee
3
250
750
... More
Fitting fixing of 200X200X100mm dia M.S outlet Tee
4
250
1000
... More
Fitting fixing of 50mm dia Air Release Valve
2
250
500
... More
Provision of leading channel at river bed to receive flow to suction point
1
2500
2500
... More
Provision for Earth cutting maintaing proper slope of earthen field bonds across the pipe line alignament & etc complete.
528
10
5280
... More
Layout for civil and electrical works
1
2500
2500
... More
Photograph of Project
1
500
500
... More
Providing electrificaton to the Pump chamber by wiring the room with required item of materials including cost ofmaterial,labour,T& P etc. complete as per direction of Engineer-in-charge.
1
4000
4000
... More
Electrical installation and energisation
1
3000
3000
... More
Electrical Earthing including all materials as per the direction of the Engineer-incharge.
2
4000
8000
... More
Construction of 11 K.V.Line 3 Ph 3 Wire with 9 Mtr long 300kg PSC pole using 55 sq.mm AAA Conductor 40 mtr span with all materials required for the same as per the specification & estimate of DISCOM
0.3
520192
156057.6
... More
L.T.Line 3ph 4w using 4x35 +1x35sq.mm XLPE ABC & 8 mtr long PSC poles with fittings with all materials required for the same as per the specification & estimate of DISCOM
0.05
496586
24829.3
... More
Installation of 63 KVA,11/.4 KV Pole mounted Sub-Station using 9 Mtr long PSC pole with Stare Ratted Transformer as per the specification & estimate of DISCOM
1
357950
357950
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%