Military Engineer Services Tender

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed.

M&L for flush pointing to random rubble masonary, uncoursed or brought upto courses in cement mortar 1:4 complete all as specified and directed.

M&L for cement concrete, type C1, 1:3:6, using 20 mm graded stone aggregate as in coping including use of formwork (straight or curved) and finishing the exposed surfaces even and smooth without using extra cement complete all as specified and directed.

S&F PVC (SWR) pipe, 110 mm dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Forming embankments including raising (or lowering) earth (solids), spreading in layers not exceeding 30cm thick, watering, ramming/rolling and finishing to required size, shape, etc., not exceeding 1.5m high from base complete all as specified and directed.

M&L for Boulder Pitching, laid dry and hand packed tightly and grouted in cement and sand mortar 1:6 complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm using excavated hard/dense soil complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above starting point complete all as specified and directed.

S&F factory made 3- 4 mm thick Polygranite Sheet of required colour for wall panelling with adhesive as per manufacturer instructions complete all as specified and directed.

M&L for Pepration of old distempered surfaces on ceiling and applying one coat of distemper oil emulsion complete all as specified and directed.

Excavating in post holes (or similar holes) each not exceeding 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard / dence soil and removing surplus soil to a distance not exceeding 50 m complete all as specified and directed.

M&L for plain cement concrete, type C2, 1:3:6 (Nominal mix), using 40 mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

S&F Mild Steel works as in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Supply only Chain link MS galvanised fencing of mesh size 75 mm X 75 mm, made of 4 mm dia galvanised steel wire, any size or type complete all as specified and directed.

Fixing only Chain link fencing of mesh size 75 mm X 75 mm including line wires, any size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

M&L for Mild steel round bars of 10mm dia and over of Grade Fe-410-W (Gde.E-250) quality-A or Fe 290 (Gde E-165), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking, horizontal stiffners in fencing wiremesh with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with 5-10 mm dia neck, hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 5cm long but not exceeding 10cm long, complete all as specified and directed.

M&L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over and including a coat of red oxide primer on new steel surfaces, over 10cm in width or girth, not otherwise described complete complete all as specified and directed.

M&L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over and including a coat of red oxide primer on new steel surfaces, not exceeding 10cm in width or girth, not otherwise described complete complete all as specified and directed.

S&F Galvanised 2 strand, steel barbed wire fencing of 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and training and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

S&F GI concertina coil of CONSEC ZAL Super Punch barb tape (SRPBT) Aluminium base helix coil with and include necessary GI fixing clips for securing complete all as specified and as directed with following specifications : (i) Dia of coil (Unstreched -610 mm), (ii) No of circle 51 turns per coil, (iii) Weight of each coil with hessian pack 8.5 kg, (iv) Coverage per coil max 8 Rm, (v) Central core wire : made from 2.6 mm dia GI-H.T.S.S wire as per IS-4454 galvanised as per IS 2629, (vi) Razor punched strip : Razor punched tape is CONSEC-ZAL steel comprising of AL base with Zinc alloy @ 150 gm/m2 conforming to ASTM-729/A-729M with additional primer treatment of Epoxy / Polyurethane & final paint top coat of Caulified green shade (BSL 139) by Hot Dipping process. The item also includes supply of 3 nos of Horizontal ZAL runner wire for fixing of Concertina coil complete all as specified and directed.