Military Engineer Services Tender

M&L for 20mm thick granite work (table rubbed and polished) in steps, jambs, pillars and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 20mm thick screed bed or bedding layer of cement morter 1:6 for laying floor finishes complete all as specified and as directed.

M&L for Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillar, windowcills, cooking platforms and like, including pointing in white cement (1:2) using marble dust with admixure of pigment to match with marble shade of Markana white over 15mm thick screed bed or bedding layer of cement morter 1:4 for layinmg floor finishes complete all as specified and as directed.

M&L for Vitrified ceramic tiles light shade 10mm thick (square / rectangular) polished, area of each tiles exceeding 0.42 Sqm but not exceeding 1.00 Sqm, in floors etc. set and jointed in net cement slurry and pointed in white and colour cement to match in light shade over 15mm thick screed bed or bedding layer of cement morter 1:4 for layinmg floor finishes complete all as specified and as directed.

M&L for brick work with sub class ‘B’ bricks (locally available best quality) straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed.

M&L for 15mm thick rendering in cement mortar (1:4), in two layers, under coat of 10 mm thick & top of 5 mm thick, to other than fair faces of brick or concrete wall surfaces, top layer 5 mm thick mixed with water proofing compound (@ 3% by weight of cement or as per manufacture's instructions), finished even and smooth without using extra cement complete all as specified and as directed. Note : Water proofing compound will be measured and paid separately as "Supply only".

Supply only integral water proofing compound complete all as specified and as directed. Note:- Dose of WPC shall be as per manufacturer instruction and the same shall be recorded in the MB.

M&L for preparation of newly plastered or previously untreated surface and finishing wall with two coat of acrylic smooth exterior paint @ 1.67 ltr/10 sqm of required shade over priming coat of exterior primer @ 2.2 Kg/ 10Sqm complete all as specified and as directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cum, getting out in hard/dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick, watering, and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and as directed.

M & L for PCC 1:3:6, type C2 (using 40 mm graded stone aggregate) as foundation of pole complete all as specified and as directed.

M & L for providing and fixing stainless steel of (grade 304) railing made of hollow tubes, channel, plates etc, including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete including fixing with railing with necessary accessories and stainless steel dash fastners, bolts etc complete all as specified and as directed.

S&F for stainless steel 8mm dia of railing chain grade SS-202 including all fitting with and fixures such as necessary stainless steel nuts and bolts complete, including fixing the railing with necessary acessories and stainless steel dash fastners, stainless steel bolts etc. complete all as specified and as directed.

M & L for preparation of new steel surface n exc 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for point wiring with single core PVC insulated unsheathed multistranded copper conductor FRLS cable for 15 Amp switch Socket combination on independent board with 2.5 sqmm copper wire 1100 volt grade drawn through and including PVC casing-capping/conduit (medium grade) of suitable size with all fittings and accessories including PVC board with cover of suitable size for housing/mounting the switches/socket etc including 2.5 Sqmm PVC insulated unsheathed single core copper conductor as earth continuty wire connected to common earth dolly, compleate all as specified and directed.

S&F MCBs, DP 6 to 32 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed. Make :- Legrand / ABB / Havells / Siemens / Schneider

S&F MCBs, SP 6 to 32 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed. Make :- Legrand / ABB / Havells / Siemens / Schneider

S & F single pole & neutral DBs 8 Ways, double door, protection class IP-43 suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 100 Amp rating copper bus bar complete all as specified and as directed. Make :- Legrand / ABB / Havells / Siemens / Schneider

S & F 1.5 sqmm flexible PVC insulated 3 core FRLS PVC sheathed multistranded cables with bright annealed electrolytic bare copper conductor for voltage grade upto 1100 v conforming to is-694:2010 In and including 20 mm pvc conduit laying in trench/wall etc, complete all as specified and directed.

S & F LED Spike/ Bush light of 7 watt with die-cast aluminium housing designed for rugged outdoor usage & IP65 protection, complete all as specified and directed. Make- Philips/Bajaj/Havells/Jaquar/GE/Crompton

S & F LED bollard 9 watt with opal acrylic diffuser and IP66 protection with necessary connection and PCC foundation etc, complete all as specified and directed. Make- Philips/Bajaj/Havells/Jaquar/GE/Crompton Note:- Cost of excevation and PCC shall deemed to be inclusive in the quoted rate.

S & F 50W LED Flood Light IP65 & IK07 waterproof protection and Impact proof outdoor Light 440V High voltage protection 3000k warm white complete all as specified and directed. Make- Panasonic/ Philips/Bajaj/Havells or equiv

M&L for plate earthing complete with galvanized mild steel plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (in earth pit not less than 2.25 m deep below normal ground level) with the top edge of the earth plate at a depth not less than 1.5 m below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and incl GI earth lead wire 4 mm dia or 8 SWG bolted (with GI nuts, bolts & check nuts) and earth plate electrode at one end and connected to main switch board/ DBs etc. at the other, earth strip encased(protected) in and including 15 mm bore GI pipe medium grade with all fittings from top of electrode to main switch board/ DBs etc fixed with and including 25 x 6mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from bottom of earth pit to top of electrode complete with earth pit in PCC 1:2:4 type B-2 using 12 mm graded crushed stone aggregate, RCC cover, funnel, wire mesh including necessary excavation and earth work complete all as specified and shown in electrical plate No 3 of SSR Pt-I complete all as specified and directed.

Supply, laying, connecting and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sqmm 4 core in trenches / through GI pipe / fixed along with pole structure etc with all fixing & connecting accessories complete all as specified and as directed. Make : Havells/Polycab/Glostar/KEI

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying cables, foundation for pole, etc and getting out in hard/dense soil complete all as specified and as directed.

Returning, filling, including spreading, levelling, watering and well ramming of soil in layers n. exc 25cm thick complete all as specified and as directed.

Removing excavated soil to distance n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and as directed.

Supply and laying GI pipe 40 mm bore light grade with all necessary fittings, fixed to pole for protection of cables with necessary coping and clamps complete all as specified and as directed.

M & L for cutting the existing hard standing/PCC/WBM road at a depth not less than 30 cm and 15 cm wide for passing of cable through GI pipe returning filling in complete including finishing the surfaces by providing cement concrete (1:2:4) type B2 using 40mm grade stone aggregate) upto 20cm depth,finishing to a uniform smooth surface to match the existing surface complete all as specified and directed. Note - GI pipes shall be measured and paid seprately under relevant item of this schedule.

M & L for Cutting & Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector) of dia 25/32 mm, complete all as specified and directed.

M & L for cutting the existing hard standing/PCC/WBM road at a depth not less than 30 cm and 15 cm wide for passing of PPR/ GI pipe returning filling in complete including finishing the surfaces by providing cement concrete (1:2:4) type B2 using 40mm grade stone aggregate) upto 20cm depth,finishing to a uniform smooth surface to match the existing surface complete all as specified and directed. Note - GI/PPR pipes shall be measured and paid seprately.

S & F open well submersible pump of capacity 0.5 HP (25mmx25mm) with control board/ panel if required and connections, complete all as specified and directed. Make-Kirloskar/V-Guard or equiv

M & L for 3 layer PP-R of outer dia 25 mm (Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches/walls etc , complete all as specified and directed.

S & F PP-R Gate valves (brass insert) as per requirement of the site of 25 mm dia, complete all as specified and directed.