Military Engineer Services Tender
View complete overview of Nagaland MES Tender
Costs
EMD
₹ 40,500Document Cost
₹ 500Tender Fee
Refer Documents
Summary
Special Repair to Bldg No T_35_36 Bcd in N Zone Special Repairs to Bldg
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2019_MES_306035_1Tender No
8165/E8Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Demolition of reed lathing single or double including battens and plaster or chicken wire lathing complete all as specified and directed by Engr-in-Charge.
75
-
-
Dismantling timber scantlings 40 sqcm and over in section, in unframed work any position complete all as specified and directed by Engr-in-Charge.
1
-
-
Demolition of cement concrete in ground floors and pavings n.exc 15 cm thick above or below ground level complete all as specified and directed by Engr-in-Charge.
4.75
-
-
Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches etc complete all as specified and directed by Engr-in-Charge.
4.25
-
-
Taking down Chowkhat or frames not exceeding 1.5 Sqm each with shutters(Without taking off shutters from the frames complete all as specified and directed by Engr-in-Charge.
23
-
-
All as per item 8 above but exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed by Engr-in-Charge.
10
-
-
S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.
205
-
-
S&F for pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.
20
-
-
S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board Classic to be fixed aluminium grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 2mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size and finally applying two coats of oil bound distemper complete all as specified and directed by Engr-in-Charge.
10
-
-
S&F asbestos cement plain building boards, fixed to timber framework/aluminium grid 6mm thick complete all as specified and directed by Engr-in-Charge.
80
-
-
M&L for non - skid coloured joint free ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engr-in-Charge.
115
-
-
All as per item No 14.00 here-in-before but as in skirting complete all as specified and directed by Engr-in-Charge.
13
-
-
M&L 10mm thick rendering on brick work or concrete surfaces as backing coat in CM 1:4 surface prepare to receive wall tiles complete all as specified and directed by Engr-in-Charge.
16
-
-
M & L screed bed 15 mm thick in cement mortar 1:6 on fair faces of brick or concrete work or under floor even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.
115
-
-
M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete all as specified and directed by Engr-in-Charge.
87
-
-
M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exc 0.11 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete all as specified and directed by Engr-in-Charge.
3
-
-
M&L for rendering 15 mm thick in CM 1:4 on one side of lathing finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.
75
-
-
M&L for rendering 12 mm thick in CM 1:6 on other side of lathing finished even and smooth without using extra cementcomplete all as specified and directed by Engr-in-Charge.
75
-
-
S & F 0.71 mm dia wire netting of galvanised steel wire of size 12 mm mesh fixed with tinned tack of wire staple complete all as specified and directed by Engr-in-Charge.
75
-
-
M&L for second class hardwood as in scantlings clean sawn timber fixed complete all as specified and directed by Engr-in-Charge.
1.9
-
-
Supply and fixed alluminium frame for door ,window ,ventilator with one oir more rebate including jointing cleat for fixing complete all as specified and directed by Engr-in-Charge.
108
-
-
S&F anodised alluminiun widow and ventilator side hang type without sasbar ,alluminium section weight 0.55kg /m including necessary jointing cleat glazing clip,rubber gusket beading etc complete all as spacified complete all as specified and directed by Engr-in-Charge.
38
-
-
S&F 4.8mm thick sheet glass selected quality exc 0 .50sqm complete all as specified and directed by Engr-in-Charge.
25
-
-
M&L for brick work with sub class 'B' bricks straight or curved on plan exc. 6.00m meanradius built in cement mortor 1:6 complete all as specified and directed by Engr-in-Charge.
0.45
-
-
Material & labour for brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed by Engr-in-Charge.
55
-
-
M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished fair and even without using extra cement complete all as specified and directed by Engr-in-Charge.
60
-
-
M&L for rendering 15mm thick in CM 1:4 other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.
62
-
-
M&L 40 mm thk PCC 1:2:4 type B-1 using20mm graded agg as in flooring finished even and smooth using extra cement complete all as specified and directed by Engr-in-Charge.
40
-
-
M & L for cement concrete 1:3:6 type C-2, 75 mm thick using 40mm graded stone aggregates as in plinth protection finished fair and even complete all as specified and directed by Engr-in-Charge.
42
-
-
M & L for cement concretetype C-2, 1:3:6 (40mm graded stone aggregates) as in surface channels and drains complete all as specified and directed by Engr-in-Charge.
4
-
-
M & L for Extra forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement complete all as specified and directed by Engr-in-Charge.
70.6
-
-
Material & labour 2nd class hardwood plain, solid straight chowkhats and frames, wrought, framed rebated on the solid,rounded or chamfered, put together with glue pinned at joints, 2nd class HW complete all as specified and directed by Engr-in-Charge.
0.38
-
-
S & F 30 mm thick flush shutters , solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engr-in-Charge.
12
-
-
S &F 2nd class hardwood 30mm thick glazed and skeleton shutters open rebated and prepared to receive glass gauze etc divided into squares, with plain, chamfered or rounded mitred and rebated sash bars any number edges of framing plain, chamfered or rounded, fitted with cut and metered beads for securing glass etc size of members of shutters as specified in SSR Part I Sec 8 clause 8.23 (a) complete all as specified and directed by Engr-in-Charge.
8
-
-
S&F mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 18mm, fixed with tinned tacks or galvanized wire staples complete all as specified and directed by Engr-in-Charge.
15
-
-
S & F 100 size stainless steel butt hinges complete all as specified and directed by Engr-in-Charge.
27
-
-
Supply & Fixing 150 mm Aluminium handles, cast type, anodised complete all as specified and directed by Engr-in-Charge.
18
-
-
S & F 200 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in-Charge.
18
-
-
S & F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed complete all as specified and directed by Engr-in-Charge.
4
-
-
S&F mild steel 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engr-in-Charge.
3
-
-
S & F second class hardwood weather boarding, clean sawn, plain, 20 mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified and directed by Engr-in-Charge.
5
-
-
Taking up or down steel tubing 15mm bore and connection including cleaning for refixing or removal to store complete all as specified and directed by Engr-in-Charge.
6
-
-
All as per item No 45.00 hereinbefore but 20mm dia complete all as specified and directed by Engr-in-Charge.
7
-
-
S&F in repairs 15mm bore GI water tubing medium grade laid in floors or fixed in wall including GI fittings complete all as specified and directed by Engr-in-Charge.
5
-
-
S&F in repairs 20 mm bore GI water tubing medium grade laid in floors or fixed in wall including GI fittings complete all as specified and directed by Engr-in-Charge.
6
-
-
Refixing 15mm dia old GI tubing and connection in new or old position (wall ceiling floor etc including cutting altering the size or changing the new fittings etc complete all as specified and directed by Engr-in-Charge.
1
-
-
All as per item No 49.00 hereinbefore but 20mm diacomplete all as specified and directed by Engr-in-Charge.
1
-
-
Supply and fixing in repairs vitreous china squatting pan water closet,Orrisa pattern of size 580mmx440mm white with integral foot rests excluding flushing cistertn and flush pipe complete all as specified and directed by Engr-in-Charge.
1
-
-
S&F in repairs 10 ltrs capacity PVC valveless syphonic action type flushing cistern low level with inlet ball valve float and handle complete all as specified and directed by Engr-in-Charge.
1
-
-
S&F liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and directed by Engr-in-Charge.
1
-
-
S& F vitrious china urinal, half stall type, white including flushing cistern, flush pipe and waste pipe. CP waste coupling complete all as specified and directed by Engr-in-Charge.
3
-
-
S&F WHB vitreous china flat back or angle back type any size, including cutting for and pinning in ends of brackets or erecting stand PVC wash pipe and PVC connection PVC 32mm dia bore waste cuppling complete all as specified and directed by Engr-in-Charge.
1
-
-
S&F pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shqanks and flynuts, screwed for iron pipe 15mm dia complete all as specified and directed by Engr-in-Charge.
1
-
-
S&F in repair for 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engr-in-Charge.
3
-
-
S&F for brass chromium plated shower rose with swivel joints, etc complete all as specified and directed by Engr-in-Charge.
1
-
-
M & L for bib cock CP with wall flange, fancy type 15 mm dia bore complete all as specified and directed by Engr-in-Charge.
2
-
-
M & L for angular stop cock CP with wall flange, fancy type 15 mm bore dia complete all as specified and directed by Engr-in-Charge.
2
-
-
S&F grating down 125mm dia with waste hole of PTMT (Min wt 40 gms) complete all as specified and directed by Engr-in-Charge.
2
-
-
S&F in repairs 600mm long tubular towel rail brass chromium plated 20mm dia, D type 60cm longfixedwith two plugs (Gutties) of 2nd class hard woodembeded in cement mortor 1:3 with MS screws complete all as specified and directed by Engr-in-Charge.
4
-
-
S&F PVC (SWR) 110mm dia single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed by Engr-in-Charge.
48
-
-
S&F PVC (SWR) 110mm dia junction single T equal or un equalwith an floor complete all as specified and directed by Engr-in-Charge.
11
-
-
S&F PVC (SWR) 110mm dia bends in any radius complete all as specified and directed by Engr-in-Charge.
11
-
-
S&F PVC (SWR) 75mm dia single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed by Engr-in-Charge.
22
-
-
S&F PVC (SWR) 75mm dia vent cowl complete all as specified and directed by Engr-in-Charge.
10
-
-
M&L for preparation of old painted wood and wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint in any tint complete all as specified and directed by Engr-in-Charge.
120
-
-
All as per item No 66 here in before but applying two coats of synthetic enamel paint over a coat of pink wood primer on new surfaces complete all as specified and directed by Engr-in-Charge.
50
-
-
M&L for preparation of new painted surfaces of steel and iron work of any description over 10 cmwidth or girth not otherwise described and applying two coat of synthetic enamel paint over a coat of redoxide on new surfaces in any tint complete all as specified and directed by Engr-in-Charge.
5
-
-
All as per item No 70.00 hereinbefore but applying one coat on old surfaces complete all as specified and directed by Engr-in-Charge.
10
-
-
M&L for distempering walls with two coats of washable distemper oil emulsion over a coat of primer on new surfaes(white or tinted) as directed uniform and smooth finish complete all as specified and directed by Engr-in-Charge.
75
-
-
All as per item No 72.00 herein before but applying two coats on old surfaces complete all as specified and directed by Engr-in-Charge.
200
-
-
M&L for Preparation of old decorated surfaces by washing, scrubbing down, and applying one coat of oil emulsion distemper on ceiling complete all as specified and directed by Engr-in-Charge.
100
-
-
Material and labour for preparation of new external surfaces of walls including cornices, plasters etc (Plastered or un plastered surfaces) and applying two coats of cement paint over one coat of primer complete all as per manufacture instructions complete all as specified and directed by Engr-in-Charge.
50
-
-
Complete removal of existing treatment of walls and preparation of old surfaces of wall including scrapping down, smoke soot, efflorescent salts trading oil and greasy spots etcapplying two coats of cement base paint over a coat of chalk whitening/primer complete all as specified and directed by Engr-in-Charge.
50
-
-
S&F for anodised aluminium door shutter, aluminium section weighting 0.55 kg/m including necessary joining, cleats,glazing clips,rubbber neoprene, packing headls 2 nos in each door hinges anodised aluminium snap beading screw etc including mortice lock with minimum three sets of key complete all as specified and directed by Engr-in-Charge.
2.5
-
-
S&F Sheet glass 5.5mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 sqm in each pane complete all as specified and directed by Engr-in-Charge.
15
-
-
M&L for prelaminated particle board 18mm thick, exterior grade, prelaminated both side with decorative choice lamination rebated or flat edged complete all as specified and directed by Engr-in-Charge.
15
-
-
Excavation in trenches in soft/loose soil not exc 1.5mtr wide and not exc 1.5 mtr deep for foundation etc or for manholes not exc 10 sqm on plan and exc 1.5 mtr but n exc 3 mtr in depth and getting out complete all as specified and directed by Engr-in-Charge.
18.73
-
-
Excavation over areas n.exc 1.5m deep & getting out soft/loose soil complete all as specified and directed by Engr-in-Charge.
47.93
-
-
Excavation over areas exc 1.5m deep & n.exc 3 m deep and getting out in soft/loose soil complete all as specified and directed by Engr-in-Charge.
42.89
-
-
Returning filling in trenches including spreading leveling watering and well ramming in 25cm layers complete all as specified and directed by Engr-in-Charge.
11.16
-
-
Removing of surplus soil at distance not exc 50mtrs & depositing complete all as specified and directed by Engr-in-Charge.
47.57
-
-
M&L PCC 1:3:6 type C2 40mm graded aggregate as in foundation of man holes, septic tank etc complete all as specified and directed by Engr-in-Charge.
2.91
-
-
PCC (1:2:4) type B-2 using 40mm graded stone aggregate as in channels of man holes complete all as specified and directed by Engr-in-Charge.
0.99
-
-
PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in band coping bed plate, benching etc including slightly rounded of chamfered angle, throating, etc complete all as specified and directed by Engr-in-Charge.
1.25
-
-
Brick work with sub class ‘B’ bricks straight or curved on plan exc 6mtr mean radius built in cement mortar (1:4) complete all as specified and directed by Engr-in-Charge.
27.76
-
-
Material and labour for brickwork in cement mortar 1:6 with sub class `B' bricks in one brick thick honey comb walling,etc complete all as specified and directed by Engr-in-Charge.
7.64
-
-
M&L 15mm thick cement plaster in cement mortar (1:4) on brick or concrete surface mixed with water proofing compound as per manufactures instructions, finishing the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.
53.76
-
-
15mm thick cement plaster in cement mortar (1:6) on other than fair face of brick surface finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.
16.1
-
-
Supply only integral water proofing compound (ISI marked) complete all as specified and directed by Engr-in-Charge.
22.45
-
-
Precast RCC (1:2:4) type B-1 in manhole/soack well/septic tanks slabs/covers etc including necessary form work complete set in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.
1.23
-
-
S&F Mild steel TMT round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips including two coat of bituminous paint complete all as specified and directed by Engr-in-Charge..
229.65
-
-
S&F TMT Steel bars 6 to 8mm dia, cut to length bent to shape required including cranking bending spirally or hopping for columns hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and directed by Engr-in-Charge.
274.32
-
-
M&L for cutting into existing manhole/soakwell/septic tank making good to pipe and benching cutting out existing benching for and forming branch channel (half round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required for internal dia size 150mm complete all as specified and directed by Engr-in-Charge.
6
-
-
Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed by Engr-in-Charge.
20
-
-
Material and labour Reinforced cement concrete (Nominal Mix) in cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in cover slabs of drains, manholes, septic tanks, soakage wells etc complete all as specified and directed by Engr-in-Charge.
Note: - Reinforcement shall be measured and paid for separately.
2.53
-
-
150mm thick PCC 1:4:8 type B1 using 40mm graded stone agg as in fdn of Septic Tank complete all as specified and directed by Engr-in-Charge
27.5
-
-
M&L 12 mm thick cement plastering in CM 1:3 as in wall/floor of septic tank complete all as specified and directed by Engr-in-Charge
9
-
-
S&F for depth 0.70m – 1.65 m, DWCPE (SN8) 180 (OD)/163(ID) mm diameter Pipes laid on 150 mm thick PCC 1:3:6 type C-2 including packing under and haunching against the sides of pipes bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional complete all as specified and directed by Engr-in-Charge
40
-
-
M & L for 25mm thick cement concrete type B-0 1:2:4 type C-2, 100 mm thick (using 12.5 mm graded stone aggregate) as in flooring complete all as specified and directed by Engr-in-Charge
10
-
-
M & L for 75 mm thick PCC 1:3:6 type C2 , using 40 mm graded agg in flooring plinth protection/aprons/path laid to slope of 1:12, finished fair and even without using extra cement with and including all necessary formwork to divide tha area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 10 mm wide joints throughout thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete complete all as specified and directed by Engr-in-Charge
60
-
-
M&L for ceramic coloured tiles of size 300x200mmx7 mm thick, on verticals surfaces, set and jointed in neat cement slurry and pointed in coloured ceemnt to match over and including 10 mm thick bedding layer of cement mortar 1 :4 complete all as specified and directed by Engr-in-Charge
30
-
-
Taking down cement plaster and raking out joints, hacking for key,scrubbing down with water built in cement mortar complete all as specified and directed by Engr-in-Charge
20
-
-
M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished fair and even without using extra cement including water proofing compound @ 2% by Wt of cement complete all as specified and directed by Engr-in-Charge
50
-
-
M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of white wash complete all as specified and directed by Engr-in-Charge
100
-
-
M&L for preparation of old plastered or unplastered surfaces of walls and applying two coats of white wash complete all as specified and directed by Engr-in-Charge
2
-
-
S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm but including brackets, waste coupling & pipe of 32 mm dia, brass chromium plated for glazed ware sink, basin, etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and complete all as specified and directed by Engr-in-Charge
7
-
-
S&F in repairs for vitreous China squatting pan wash down water closet "orrissa pattern', size 580x440 mm , white with integral foot rest (excluding fixing bolts, flushig cistern and flush pipe) complete all as specified and directed by Engr-in-Charge
7
-
-
S & F in repair PVC valve less, syphonic action type, low level flushing cistern 10 ltrs capacity white, with inlet, ball valve, float and handle including PVC flush down pipe and brackets etc, and flush pipe of 32 mm dia of low or high density for low level cistern complete all as specified and directed by Engr-in-Charge
11
-
-
S&F PVC connection 15mm dia and 60cm long with two Nos of brass checknuts and washers complete all as specified and directed by Engr-in-Charge
4
-
-
S & F low density polythyelene (LDPE) pipes 32 mm dia of pressure rating 6 kgf/Sq cm complete all as specified and directed by Engr-in-Charge
4
-
-
S & F in repair soap dish, any type of size 160x60x90mm fixed to plug with chromium plated brass screws complete all as specified and directed by Engr-in-Charge
30
-
-
S&F 15mm dia steel tubes medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor including taking up or down existing tube and removal to store complete all as specified and directed by Engr-in-Charge
5
-
-
All as per item No 116.00 hereinbefore but 20mm dia complete all as specified and directed by Engr-in-Charge
5
-
-
All as per item No 116.00 hereinbefore but 25mm dia complete all as specified and directed by Engr-in-Charge
9
-
-
S & F in repairs 15 mm bib tap chromium plated fancy type cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-Charge
2
-
-
S&F in repairs 15mm dia pillar taps fancy type cast copper alloy, with capstan heads, chromium plated screwed down high pressure, with or without lettered 'Hot' or 'Cold with long screwed crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed. shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engr-in-Charge
11
-
-
S&F in repairs for 15mm dia of pipe stop valves,fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed complete all as specified and directed by Engr-in-Charge
6
-
-
M&L PVC (SWR) floor trap, plain with grating including jointing to waste pipe in cement mortar 75mm diacomplete all as specified and directed by Engr-in-Charge
1
-
-
M&L dismantling water tank of exc 500 ltr and not exc 1000 ltr Capacity complete all as specified and directed by Engr-in-Charge
1
-
-
S&F rotational moulded polyethylene 1000 Ltrs Capacity water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball brass valve, with polythelene float and fly nut complete screwed down for iron pipe of 20 mm dia complete all as specified and directed by Engr-in-Charge
1
-
-
S & F in repairs Ball valves 25 mm high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms) complete all as specified and directed by Engr-in-Charge
1
-
-
S& F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed by Engr-in-Charge
1
-
-
S& F in repair 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed by Engr-in-Charge
2
-
-
S&F in repairs brass Choromium plated shower rose with or without swivel joints 125mm size including fixing to steel pipe or union complete all as specified and directed by Engr-in-Charge
4
-
-
M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge
17
-
-
All as per item No. 129.00 here in before but not exceeding 10 cm width or girth complete all as specified and directed by Engr-in-Charge
62
-
-
S&F for 4 mm thick veneered decorative Plywood (no of ply 05), grade-I (with BWR resin) with decorative face veneers on one face, fixed with screws to timber frame work complete all as specified and directed by Engr-in-Charge
62
-
-
M&L for preparation of new surfaces of any description, over 10cm in width or girth and applying two coat of varnishing complete all as specified and directed by Engr-in-Charge
30
-
-
Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell/ buzzer, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good to the disturbed surfaces of walls, ceiling, floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface complete all as specified and directed by Engr-in-Charge.
81
-
-
Point wiring complete with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable 1100 volts grade with multi-stranded copper conductors, drawn through and including PVC double locked Casing & caping including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators etc. with 3 mm thick plastic laminated sheet cover of suitable size as required at site and 50 mm deep ccomplete all as specified and directed by Engr-in-Charge.
Make : RR Kable/Havells/Finolex/Richa
Make of PVC Casing Caping/Conduit : Supreme/Ori-Plast/Finolex/Richa/Presto Plast
1
-
-
One light point controlled by one, one way switch .
40
-
-
One Ceiling fan point controlled by one, one way switch.
9
-
-
One 3 pin socket outlet 5 Amps on the same board with other switches.
4
-
-
One 3 pin socket outlet 5 Amps on the switch socket combination.
17
-
-
All as per item No- 134.00 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed by Engr-in-Charge.
Make : RR Kable/Havells/Finolex/Richa
11
-
-
M&L for Switch piano flush type single pole, one way 5A complete all as specified and directed by Engr-in-Charge.
Make : Anchor/SSK/Plaza
70
-
-
M&L for Socket outlet, 2 in 1, 5 pin 5A flush type complete all as specified and directed by Engr-in-Charge.
Make : Anchor/SSK/Plaza
20
-
-
M&L for Switch Socket combination, 2 in 1, 5 pin 6A/16A flush type complete all as specified and directed by Engr-in-Charge.
Make : Anchor/SSK/Plaza
11
-
-
M&L for stepped type electronic fan regulator 100 Watt socket size flush type on the existing phenolic laminated sheet etc complete all as specified and directed by Engr-in-Charge.
Make : Anchor/SSK/Plaza
9
-
-
M&L for ceiling rose 3 terminal PVC/Polycarbonate isolated body with PVC round/squareblock complete all as specified and directed by Engr-in-Charge.
Make : Anchor/SSK/Plaza
36
-
-
M&L for sub main wiring with two runs of 4.0 Sq mm and one run of 2.5 Sq mm for earth wire with multi standard copper conductors of , 1100 volts grade, drawn through and including PVC double locked Casing & caping including complete all as specified and directed by Engr-in-Charge.
Make : RR Kable/Havells/Finolex/Richa
30
-
-
M&L for Lamp holder , PVC/ Polycarbonate type with PVC round/square block incl 9 watt LED lamp suitable for lamp holder fittings incl taking down old unsv light fitting complete all as specified and directed by Engr-in-Charge.
Make : Anchor/SSK/Plaza Make : LED Lamp Havells/Bajai/CG
12
-
-
M&L for 20W LED, 4', Wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver.etc with all accessories internally pre-wired and fixing the same on and including two Nos PVC blocks and connecting up with flexible copper cable of suitable size from ceiling rose to the light fitting incl taking down old unsv light fitting complete all as specified and directed by Engr-in-Charge.
Make : Havells Cat No LHFXCEP1TNNW020(batten) & LHDLEFXD5LR020(LED Tube) or equivalent in Bajaj/Philips
21
-
-
M&L for 10 watt LED, 2', Wall mounted with polycarbonate housing/ batten complete all as specified and directed by Engr-in-Charge.
Make Havells Cat No LHEXBQP5IN1W009 or equivalent in Bajaj/Philips
2
-
-
M&L for LED 1x20W Security light fitting, drawn through including GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling holes as required and connecting up with flexible copper cable of suitable size from ceiling rose to the light fitting complete all as specified and directed by Engr-in-Charge.
Make : Havells Cat No LHETBXU7PA6S020 or equivalent in Bajaj/Philips
4
-
-
M&L for MCB Distribution board double door type SPN 8 way, sheet steel, powder painted, with neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and directed by Engr-in-Charge.
Make:- Legrand Cat No 507621 or equivalent in ABB/Siemens
1
-
-
M&L for MCB Distribution board double door type SPN 4 way, sheet steel, powder painted, with bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv DB, complete all as specified and directed by Engr-in-Charge.
Make:- Legrand Cat No 507620 or equivalent in ABB/Siemens
1
-
-
M&L for MCB SPN 40 Amps 'C' series, 230 volts, 50 Hz suitable for fixing in MCB DB incl taking down old unsv MCB complete all as specified and directed by Engr-in-Charge.
Make:- Legrand Cat No 408617 or equivalent in ABB/Siemens
2
-
-
M&L for MCB SP 5-32 Amps 'C' series, 230 volts, 50 Hz suitable for fixing in MCB DB incl taking down old unsv MCB complete all as specified and directed by Engr-in-Charge.
Make:- Legrand Cat No 408587 to 408595 or equivalent in ABB/Siemens
8
-
-
Taking down Ceiling fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearing, painting of fans complete with superior quality synthetic enamel paint by spraying including filling cavaties with filler, after cleaning all dust, reassembling the fan and blades, hanging/ fixing the fan in its original position and testing on completion complete all as specified and directed by Engr-in-Charge.
9
-
-
M&L for rubber bush with clamping set, comprising GI bolt, nut and split pin complete all as specified and directed by Engr-in-Charge.
9
-
-
M&L for replacement of capacitor2.5 Mfd incl making electrical connection complete all as specified and directed by Engr-in-Charge.
Make : Havells/L&T/EPCOS/Anchor or equivalent approved make
8
-
-
M&L for replacement of steel ball bearing/bush of suitable size compatible to the existing ceiling fan complete all as specified and directed by Engr-in-Charge.
Make : SKF/Any ISI Mark as approved by GE.
8
-
-
M&L for copper rewinding for suitable size complete to the existing ceiling fan complete all as specified and directed by Engr-in-Charge.
8
-
-
Taking down LT UG cable/ service connection of any size and M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 16 sq mm, 2 core complete all as specified and directed by Engr-in-Charge.
NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items.
Make : Richa/Havells/polycab/finolex
50
-
-
Supply & laying tubas ' medium grade ' galvanised GI tubing with all fittings, fixed complete to walls/laid in floors/trenches/road crossing of size 20 mm dia bore complete all as specified and directed by Engr-in-Charge.
Make : Jindal/TATA/National/Surya
10
-
-
Cutting existing GI tubing pipes 20 mm bore and screwing existing steel tubing for addition to form connecter in position complete all as specified and directed by Engr-in-Charge.
Make : Jindal/TATA/National/Surya
1
-
-
M&L for replacement of laying of LT electric cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, croos-sectional area of 10 Sqmm 2 Core suspended with 4 sqmm GI conductor including taking down old cable complete all as specified and directed by Engr-in-Charge.
Make : RR Kabel/Havells/polycab
70
-
-
M&L for house service bracket hook type complete with 3 mtr long GI pipe 40 mm dia medium grade, 02 Nos 90 degree bends MS hook and stay/guy incl twos Nos,''D'' clamp made out of 50x6 mm MS flat and suitable Nos of nut bolts and washers complete fixed to wall complete all as specified and directed by Engr-in-Charge.
Make : Jindal/TATA/National/Surya
1
-
-
M&L for spread fine river sand in trenches complete all as specified ans as directed. NOTE: For measurement purpose, punned down thickness shall only be taken complete all as specified and directed by Engr-in-Charge.
3.6
-
-
M&L for laying brick sub class 'B' old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and directed by Engr-in-Charge.
391
-
-
Supply & laying tubes ' light grade' galvanised, with all fittings, fixed complete to walls, poles, ceilings or laid in floors/ trenches/ road crossing for protection of cables of size 40 mm dia bore including taking out unsv GI tubing complete all as specified and directed by Engr-in-Charge.
Make : Bansal/Tata/Jindal/Prakash or equivalent approved make.
12
-
-
Material and labour for boring of hole under roads with mechanical arrangement upto 80 mm dia without disturbing the top surface of the road for passing the cable across the road complete all as specified and directed by Engr-in-Charge.
6
-
-
M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and directed by Engr-in-Charge.
NOTE:- (i) The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 chamber with CI cover plate 10mm thick including angle iron frame , funnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 389 of MES SSR Part-II. (ii) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately. (iii) Test points shall be made of GI strip 32x6 mm bridge type mounted on insulators, where ever applicable
2
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements