Military Engineer Services Tender
View complete overview of Mizoram MES Tender
Costs
EMD
₹ 65,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2023_MES_634718_1Bid Award Id
ViewTender No
8836/E8Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Dismantling wall and ceiling boards (fibre,pulp, insulation, etc. or insulation boards/slabs/blankets, any thickness including cover fillets, frameworks, etc. complete all as specified and as directed
80
-
-
Taking down chowkats or frames not exceeding 1.5sqm each with shutters (without taking off shutters from the frame) and disposing off
24
-
-
Taking down chowkats or frames exceeding 1.5sqm but not exceeding 4sqm each but with shutters (without taking off shutters from the frame) and disposing off
18
-
-
Taking down shutters of any description not exceeding 1sqm area and disposing off complete all as specified and as directed
11
-
-
Taking down shutters of any description exceeding 1sqm but not exceeding 2.0sqm area and disposing off complete all as specified and as directed
32
-
-
Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles and disposing off complete all as specified and as directed
13.4
-
-
Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for keys, scubbing down with water, etc. including all necessary scaffolding as required and rubbishing off the premises, etc. complete all as specified and as directed
205
-
-
Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and disposing off complete all as specified and as directed
230
-
-
Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removal of debris complete all as specified and as directed
20
-
-
Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for and removal of debris complete all as specified and as directed
4
-
-
Demolition and breaking up CI drain pipes 75mm bore (internal dia) set in cement mortar in any position or location and disposing off complete all as specified and as directed
30
-
-
Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) 100/110mm bore (internal dia) set in cement mortar in any position or location including breaking off haunching and disposing off complete all as specified and as directed
120
-
-
Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) 150mm bore (internal dia) set in cement mortar in any position or location including breaking off haunching and disposing off complete all as specified and as directed
50
-
-
Demolition and breaking up PVC pipes 200mm bore (internal dia) set in cement mortar in any position or location and disposing off complete all as specified and as directed
35
-
-
Taking up or down 15mm bore steel water tubing and connections from any location / position including disposing off, etc. complete all as specified and as directed
80
-
-
Taking up or down 20mm bore steel water tubing and connections from any location / position including disposing off, etc. complete all as specified and as directed
35
-
-
M&L for taking down wooden shutters of any description area not exceeding 1.0sqm each and refixing / resecuring same after necessary easing, adjusting, repairs, etc. with providing new screws complete all as specified and as directed
5
-
-
M&L for taking down wooden shutters of any description area exceeding 1.0sqm but not exceeding 2.0sqm each and refixing / resecuring same after necessary easing, adjusting, repairs, etc. with providing new screws complete all as specified and as directed
10
-
-
M&L for loose filling with broken brick aggregates of gauge 80 to 150mm in soakage pits, soakage wells, etc. complete all as specified and as directed
3
-
-
M&L for brickwork with sub-class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in CM (1:6) complete all as specified and as directed
3
-
-
M&L for brickwork with sub-class 'B' bricks, straight or curved on plan to any radius as in half brick thick walls built in CM (1:4) complete all as specified and as directed
90
-
-
S&F bands, straps, hold fasts, wall ties, and similar articles conforming to Fe-290 grade E-165 complete all as specified and as directed
10
-
-
M&L for mild steel TMT bars grade Fe-500D, 10mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed
200
-
-
M&L for mild steel TMT bars grade Fe-500D, 6 to 8mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed
50
-
-
M&L for use and waste of formwork to soffits of suspended slabs such as in roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified and as directed
20
-
-
M&Lfor use and waste of formwork to edges of concrete flats, treads, breaks in floors, floor and roofs not exceeding 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide complete all as specified and as directed
40
-
-
M&L for RCC 1:1.5:3 type A-1 using 20mm graded mechanically crushed stone aggregates as in slabs supported on walls, beams and columns, in floor, roof, landing, balconies, shelves and the like complete all as specified and as directed
Note: Reinforcement and formwork will be measured and paid separately under respective items
2
-
-
M&L for precast RCC 1:2:4 type B-1 using 20mm graded mechanically crushed stone aggregates as in cover slab for man holes, drains, soak wells, and similar articles, set in CM 1:4 with plain faces including necessary formwork and chamfering, weathering, throating, etc. complete all as specified and as directed
2
-
-
M&L for plain cement concrete 1:3:6 (type C-1) using 20mm graded stone aggregate as in filling of hold fast holes, etc. complete all as specified and as directed
0.3
-
-
M&L for plain cement concrete 1:3:6 (type C-2) using 40mm graded stone aggregate as in foundation filling, mass concrete, complete all as specified and as directed
0.5
-
-
M&L for plain cement concrete type C-1,1:3:6 (using 20mm graded stone aggregates) as in surface channels, drains, etc. complete all as specified and as directed
1.5
-
-
M&L for 75mm thick plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregates) as in floors, plinth protection, pavings, etc. surface finished even and fair, laid in alternate bays/panels and joints filled with bituminous mix of 1 part bitumen and 3 part of sand complete all as specified and as directed
70
-
-
M&L for 75mm thick plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregates) as in sub-bases, etc. surface finished even and fair complete all as specified and as directed
90
-
-
M&L for plain cement concrete 1:3:6 (type C-2) using 40mm graded stone aggregate for bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm dia drain pipes complete all as specified and as directed
15
-
-
M&L for plain cement concrete 1:3:6 (type C-2) using 40mm graded stone aggregate for bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 110mm dia drain pipes complete all as specified and as directed
60
-
-
M&L for plain cement concrete 1:2:4 (type B-2) using 40mm graded stone aggregate as in foundation filling, mass concrete, complete all as specified and as directed
1
-
-
M&L for 100mm thick plain cement concrete type B-2,1:2:4 (using 40mm graded stone aggregates) as in bedding layers, paving, hard standing, etc. complete all as specified and as directed
50
-
-
M&L for forming construction joint 30mm deep x 10mm wide filled with sealing compound grade 'B' complete all as specified and as directed
15
-
-
Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc. complete all as specified and as directed
Note: Inner girth shall only be measured
60
-
-
M&L for finishing newly plastered surfaces of masonry / concrete using extra cement complete all as specified and as directed
50
-
-
M&L rendering 15mm thick, in cement mortar (1:4) on walls / concrete surfaces, etc. in two layers (10+5mm) finishing layer mixed with integral water proofing compound @3% by weight of cement, finished even and fair without using extra cement complete all as specified and as directed
Note: WPC will be measured and paid separately under respective item herein
164
-
-
M&L for rendering 15mm thick in cement mortar (1:6) on fair surfaces of PCC block / brick masonry wall / concrete surfaces, etc. finished even and fair without using extra cement complete all as specified and as directed
160
-
-
M&L for rendering 15mm thick in cement mortar (1:4) on other side of lathing finished even and fair without using extra cement complete all as specified and as directed
30
-
-
M&L for rendering 15mm thick in cement mortar (1:6) on other side of lathing finished even and fair without using extra cement complete all as specified and as directed
30
-
-
Supply only integral water proofing compound all as specified
18
-
-
M&L for non-skid ceramic tiles, coloured, area of tile exceeding 0.06sqm but not exceeding 0.11sqm each, 7 to 8mm thick of superior quality as in floors, etc. laid over 15mm thick screed bed in CM (1:6) (rate shall be included) set and jointed in neat cement slurry @3.00kg of cement per sqm and pointed in white cement mixed with colouring pigment to match shade of tiles complete all as specified and as directed
80
-
-
M&L for glazed ceramic tiles, coloured of size 350x250mm or 450x350xmm x7 to 8mm thick, of superior quality B-III grade, on vertical faces, dados, skirting, risers, etc. laid over 10mm thick backing coat in CM (1:4) (rate shall be included) set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles complete all as specified and as directed
60
-
-
M&L for rubber moulded reflective type chequered cement concrete tiles 300x300x25mm thick, set, jointed and pointed in neat grey cement slurry mixed with pigment to match colour of tiles as in floors laid over and including 15mm screed bed in CM 1:4 (rate shall be included) complete all as specified and as directed
90
-
-
S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed
0.3
-
-
S&F solid PVC door frame of size 50x47mm made out of 5mm thick plain / printed coloured PVC sheet (as approved) reinforced with MS square tube all as per specifications and drawing given in SSR Part-I 2009 all as per manufacturer's instructions and making good the disturbed surfaces complete all as specified and as directed
90
-
-
S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified and as directed
18.7
-
-
S&F factory made 28 to 30mm thick single/double leaf solid PVC moulded door shutter with particle board core (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet polyurethane painted on the front face & 2mm plain colour termite proof, water proof and fire resisitant PVC sheet on back face, duly fixed in frame at site as per specification complete all as specified and as directed
14
-
-
S&F factory made wire gauzed PVC door shutter 30mm thick (style) panel will be of wire gauze in lieu of single side pre-laminated sheet panel, wire gauze duly wrapped on an additional sqaure 8mm MS solid tube,welded to MS tubes, the wire gauze shall be stretched and tightened firmly consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and pre-laminated colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and at site as per clause 8B.2.1 of MES schedule Part-II (2004) complete all as specified and as directed
14
-
-
S&F 2nd class hard wood glazed and skeleton ventilator/window 35mm thick open rebated and prepared to receive glass, wiremesh gauge etc (without sash bars), edge of framing plain chemfered rounded fitted with cut and mitred beds for securing glass etc size of members size of members of shutter as specified in SSR Part-I section 8 clause 8.20(a) complete all as specified and as directed
12
-
-
S&F 30mm thick 2nd class hard wood glazed and skeleton door shutters, open rebated and prepared to receive glass, gauge, etc and divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, sizes of members of shutters as specified in clause 8.20 9(b) of SSR Part-I, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., supplied and fitted to chowkats complete all as specified and as directed
21.6
-
-
M&L 35mm thick factory made plain framed paneled door shutter (two panels) 2nd class HW rail and style with lock rail and panels of 12mm thick ISI marked veeneered particle board with commercial veeneering on both faces, with size of rail and style shall be as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and as directed
12
-
-
S&F factory fabricated flush shutters, 30mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed
22
-
-
&F alluminium anodized glazed doors shutter including frame with the following specifications: door frame of size 50x65x1.5mm thick, door shutter with stiles of size 85x45x1.5mm thick, top and bottom rails sizes 100x43x1.5mm and lock rails size 85x43x1.5mm, upper panel to be glazed with 5mm thick coloured glass and lower panel to be provided with prelaminated particle board, cleat type aluminium handles, stainless steel hinges, lugs and necessary locking arrangements including all necessary accesorries viz. gass, pre-laminated particle board, fiitings (cost shall be included) complete all as specified and as directed
12
-
-
S&F 3 way sliding anodized aluminium glazed window shutter with frame complete all as specified and as directed with the following specifications:
(a) Window frame 3 track of size 95x25x1.5mm thick
(b) Stiles and rails of size 35x25x1.5mm
(c) 35x35x1.5mm T section mullion (d) PVC gasket with 4mm thick tinted glass, incl. aluminium handles with necessary locking arrangement for 02Nos glazed shutter
(e) Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples incl. aluminium handles with necessary locking arrangement for 01No gauzed shutter
Note: Measurement to be taken as overall width and height of window i.e. size of opening will be considered for measurement purposes. All necessary accessories including tinted glass and stainless steel wire cloth required for assembling and fixing window at proper place shall be deemed to be included in the quoted rate
12
-
-
S&F 2 way sliding anodized aluminium glazed ventilator shutter with frame complete all as specified and as directed consisting of following specifications:
(a) Ventilator frame 2 track of size 60x25x1.5mm thick
(b) Stiles and rails of size 35x25x1.5mm
(c) 35x35x1.5mm T section mullion
(d) PVC gasket with 4mm thick tinted glass, including aluminium handles with necessary locking arrangement
Note: Measurement to be taken as overall width and height of window i.e. size of opening will be considered for measurement purposes. All necessary accessories including tinted glass and stainless steel wire cloth required for assembling and fixing window at proper place shall be deemed to be included in the quoted rate
1.35
-
-
S&F 2nd class hard wood timber scantling in clean sawn framed & fixed to framed work complete all as specified and as directed
0.7
-
-
M&L for 2nd class hard wood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails, sectional area exceeding 6sqcm but not exceeding 13sqcm as in plaster beads complete all as specified and as directed
60
-
-
M&L for 2nd class hard wood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails, sectional area exceeding 13sqcm but not exceeding 25sqcm complete all as specified and as directed
40
-
-
S&F 2nd class hard wood pieces, small let in for making good where hinges, etc. have been removed from chowkhats or frames, joinery, etc.
including painting or oiling to match, if required complete all as specified and as directed
40
-
-
S&F 18/19mm thick pre-laminated particle board, exterior grade, pre-laminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws or nuts & bolts as required complete all as specified and as directed
6
-
-
S&F in repairs 12mm thick pre-laminated particle boards, prelaminated both sides with decorative choice laminations, with glazing clips, rubber / aluminium beading / gasket, suitable for aluminium doors, etc. complete all as specified and as directed
5
-
-
S&F solid PVC wall lining consisting of 5mm thick plain coloured PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and as shown on drawing complete all as specified and as directed
80
-
-
S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and as shown on drawing complete all as specified and as directed
130
-
-
S&F double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed
5
-
-
S&F in repairs door closer hydraulically regulated, designation No. 1 universal type of aluminium (extruded section body) suitable for door shutters complete all as specified and as direcetd
17
-
-
S&F 300mm, mild steel, ordinary rat tail rod pattern door springs including roller and roller plate complete all as specified and as directed
22
-
-
S&F 3mm thick sheet glass ordinary quality and glazing with oil putting square not exceeding 0.5sqm in each pane complete all as specified and as directed
5
-
-
S&F 3mm thick sheet glass ordinary quality and glazing with oil putting including hacking out old broken glass (any thickness, size quality or description) from wooden frame or stone, concrete or brick surrounds, glazed with putty or fixed with beads square not exceeding 0.5sqm in each pane complete all as specified and as directed
10
-
-
S&F 4mm thick sheet glass ordinary quality and glazing with oil putting including hacking out old broken glass (any thickness, size quality or description) from wooden frame or stone, concrete or brick surrounds, glazed with putty or fixed with beads square exceeding 0.5sqm in each pane complete all as specified and as directed
5
-
-
S&F 4.8mm thick sheet glass ordinary quality and glazing with oil putting including hacking out old broken glass (any thickness, size quality or description) from wooden frame or stone, concrete or brick surrounds, glazed with putty or fixed with beads square exceeding 0.5sqm in each pane complete all as specified and as directed
8
-
-
S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed
15.6
-
-
S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed
25
-
-
S&F for GI wire netting 0.71mm dia and 12mm mesh lathing to wood or metal studding joints, etc. in walls, ceiling stanchion, beams, etc. including all laps cutting and wastes complete all as specified and as directed
30
-
-
S&F in repairs 20mm dia fancy type powder coated (tint as approved) aluminium curtain / drapery rods, etc. of rod wall thickness 1mm (min), including pair of aluminium, powder coated brackets, holders with funnel at ends complete all as specified and as directed
50
-
-
S&F 300mm aluminium anodised sliding door bolt with hasp and staple, bolt type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed
30
-
-
S&F brass mortice lock, vertical type, of size 100mm, 4 levers, with key in duplicate set complete all as specified and as directed
10
-
-
S&F rubber beading for securing glass of suitable size complete all as specified and as directed
60
-
-
S&F door brush in vertical style for air insulation duly fixed with staples,etc. complete all as specified and as directed
10
-
-
S&F PVC roller of aluminium body of suitable size for sliding shutters complete all as specified and as directed
50
-
-
S&F side locks of aluminium body, suitable size for sliding shutters complete all as specified and as directed
30
-
-
S&F 150mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and as directed
108
-
-
S&F 100mm long aluminum anodised barrel tower bolt of extruded section complete all as specified and as directed
40
-
-
S&F 150mm extruded aluminum alloy handles, cast type, anodized complete all as specified and as directed
108
-
-
S&F in repairs 150mm extruded aluminum alloy handles, cast type, anodized complete all as specified and as directed
10
-
-
S&F 100mm extruded aluminum alloy handles, cast type, anodized complete all as specified and as directed
40
-
-
S&F in repairs 100mm extruded aluminum alloy handles, cast type, anodized complete all as specified and as directed
10
-
-
S&F 100mm MS butt hinges, medium weight, cold rolled complete all as specified and as directed
172
-
-
S&F in repairs 100mm MS butt hinges, medium weight, cold rolled complete all as specified and as directed
20
-
-
S&F 75mm MS butt hinges, medium weight, cold rolled complete all as specified and as directed
90
-
-
S&F in repairs 75mm MS butt hinges, medium weight, cold rolled complete all as specified and as directed
15
-
-
M&L for preparation of new masonry / concrete wall surfaces and applying two coats of oil emulsion distemper (tint as approved) over a coat of wall primer including all necessary staging, scaffolding, safety precautions, etc. as required to work at heights, etc. complete all as specified and as directed
100
-
-
M&L for complete removal of old treatment and preparation of masonry / concrete wall surfaces and applying two coats of oil emulsion distemper over a coat of wall primer and 1mm thick wall care putty including all necessary staging, scaffolding, safety precautions, etc. as required to work at heights, etc. complete all as specified and as directed
70
-
-
M&L for applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistant, dirt resistant, exterior paint of approved shade (company depot tinted) with silicon additives @1.43litre/10sqm over and including a priming coat of exterior primer applied @0.90 litre/10sqm over new surfaces of brickwork,concrete, etc. including all necessary staging, scaffolding, etc.required complete all as specified as as directed
194
-
-
M&L for preparing of new wood / wood based surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, tint as approved complete all as specified and as directed
137.7
-
-
M&L for preparation of new wood or wood based surfaces of any description not exceeding 10cm in width or girth and applying two coats of synthetic enamel paint (of approved tint) over one coat of pink primer complete all as specified as as directed
10
-
-
M&L for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with creosote oil complete all as specified and as directed
32.6
-
-
S&F in repairs 15mm bib taps, chromium plated, cast copper alloy, long neck with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed
35
-
-
S&F in repairs 15mm dia pillar taps, fancy type, cast copper alloy, with capstain heads, chromium plated, screwed down, high pressure, with or without lettered 'HOT'/'COLD', with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed
10
-
-
S&F in repairs 15mm dia stop cocks, cast copper alloy, concealed type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions or for brass ferrule complete all as specified and as directed
10
-
-
S&F in repairs 15mm dia angle valves, cast copper alloy, concealed type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions or for brass ferrule complete all as specified and as directed
10
-
-
S&F steel water tubing, medium grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to walls or laid in floors / trenches required for water connections complete all as specified and as directed of the following bores:
-
-
-
15mm bore
70
-
-
20mm bore
25
-
-
Relaying / refixing only steel water tubing, medium grade, galvanised with screwed and socketed joints, including supply and fixing all fittings, ISI marked conforming to IS-1239 and fixed to walls or laid in trenches required for water connections complete all as specified and as directed for the following bores:
Notes: (a) Serviceable tubings obtained from dismantling herein before will be reused under this item
(b) Tubings shall be thoroughly cleaned off from dirt, mud, silt, rust, etc., duly de-scaled and threaded before reuse
-
-
-
15mm bore
10
-
-
20mm bore
10
-
-
S&F in repairs vitreous China squatting pan, Orissa pattern of size 580x440mm, white, with integral foot rests and 'P' or 'S' trap, connecting to flushing pipe, cast iron 100mm bore 'P' trap with 500 to 600mm long neck including necessary lime concrete and making good to the disturbed surfaces in CM 1:3 with finishes to match with the existing complete all as specified and as directed
3
-
-
S&F in repairs vitreous China wash down water closet pan (Pedestal pattern), white, with 'P' or 'S' trap, including flush pipe, trap, connection to drain or outgoing pipe, anti-syphonic pipe, seat cover to match with colour of WC, closed pattern with flat bottom & cover and chromium plated mild steel or aluminum anodized hinge device and jointing and connecting up complete all as specified and as directed
3
-
-
S&F in repairs single piece vitreous China wash down water closet pan (Pedestal pattern), white, with 'P' or 'S' trap, including flush pipe, trap, connection to drain or outgoing pipe, anti-syphonic pipe, seat cover, closed pattern with flat bottom & cover and chromium plated mild steel or aluminum anodized hinge device and jointing and connecting up complete all as specified and as directed
Make: Cat part No. 20125 of Hindware or equivalent of Kohler, Duravit, Grohe, Roca, Jaquar
3
-
-
S&F in repairs vitreous China bowl urinal flat back half stall of size 590x390x375mm (minimum), white, with grating and union for discharge pipe, including providing fixing plugs, brackets, grating, union and connections to flushing pipe, bedding urinal against wall in CM 1:2, securing bowl with plugs and 60mm long brass screws, pointing around urinal bowl in white cement (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and as directed
5
-
-
S&F in repair plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed
20
-
-
S&F 10litres capacity PVC flushing tank, white / coloured, syphonic action type, low level, valveless, with PVC inlet ball valve, PVC flush pipe, float and suitable sized brackets including cutting of floor / wall and making good to the disturbed surfaces in CM 1:3 with finishes to match with the existing and taking down of old PVC flush tank and disposing off complete all as specified and as directed
20
-
-
S&F health faucet, 15mm bore, telephone type, with CP arms, flexible pipe (ABS body) with 1.25m long stainless steel braided tube and ABS wall hook of approved finish including making all necessary connections complete all as specified and as directed
20
-
-
S&F vireous China soap dish, 160x160x90mm (minimum), of approved design, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed
5
-
-
S&F in repairs toilet paper holder with flap, 6'' wide, brass chromium plated, of approved deisgn and finish and fixed with steel screws and wooden/rawl plugs complete all as specified and as directed
5
-
-
S&F in repairs 15mm PVC connections, 450mm long with brass couplings, PTMT nuts, etc. complete all as specified and as directed
20
-
-
M&L for cleaning of kitchen / bathroom trap (floor trap/ gully trap) by using rubber pump and rod including removal of sludge and other foreign materials complete all as specified and as directed
1800
-
-
M&L for desilting of sewer lines of 110 to 150mm bore, by removing either by mechanical or manual means, the exiting slush/hardened silt/sludge/ any other hardened debris accumulated over a period and in foul conditions (debris like concrete pieces, stone boulders, hardened lime, etc.) including taking out these materials through existing manholes/openings with a lift upto 2m, transportation and depositing at a point within a lead exceeding 50m but not exceeding 100m, spreading, dressing and leveling the heaps to a level not higher than 1m level including all tools, tackles, equipment, labour, etc. complete all as specified and as directed
200
-
-
M&L for cleaning / de-sludging of septic tanks, using mechanical pumps, diesel driven, with fuel, operator, etc. and all necessary tools / plants including loading and carting off the drawn sludge, waste material, scum, spoil water, etc. outside MD land through designated sludge carriers / bio tanks complete all as specified and as directed of the following capacities:
-
-
-
10 Users
30
-
-
25 Users
80
-
-
50 Users
120
-
-
M&L for cleaning / de-sludging of sewage soakage wells/pits of depth 10 to 12m, using mechanical pumps, diesel driven, with fuel, operator, etc. and all necessary tools / plants including loading and carting off the drawn sludge, waste material, scum, spoil water, etc. outside MD land through designated sludge carriers / bio tanks complete all as specified and as directed
250
-
-
Notes for item Nos. 125 to 131:
(i) All necessary precautions and all safety measures as per Municipality rules / relevant regulatory guidelines shall be taken by the Contractor in employing his mechnical means and workmen. No person shall be employed in direct contact working in septic tanks, manholes, sewage wells, etc. in foul conditions to prevent any health hazards, etc. and only mechanical means shall be used
(ii) The Contractor shall be solely responsible for any mishap to any of labourer deployed and to equipment/machinery/plants/material, etc. brought at site for work and any lapses whatsoever during the execution, (iii) The work shall be executed under the supervision of highly skilled tradesman / supervisor
(iv) Drawn sludge, waste material, scum, spoil water, etc. shall be removed to outside MD land through designated sludge carriers / bio tanks only
(v) To avoid any hazard or spreading of any foul gas bleaching powder shall be spread as directed
(vi) The rates quoted shall be deemed to be inclusive of the above aspects, and no claims whatsover shall be entertainable at later stages and or during execution
-
-
-
S&F PVC pipes, 200mm bore, single socketed in any length with rubber ring joints fixed on walls with suitable clamps, etc. complete all as specified and as directed
35
-
-
S&F PVC (SWR) pipes, 150mm bore, single socketed in any length with rubber ring joints fixed on walls with suitable clamps, etc. complete all as specified and as directed
50
-
-
S&F PVC (SWR) pipes, 110mm bore, single socketed in any length with rubber ring joints fixed on walls with suitable clamps, etc. complete all as specified and as directed
60
-
-
S&F PVC (SWR) pipes, 75mm bore, single socketed in any length with rubber ring joints fixed on walls with suitable clamps, etc. complete all as specified and as directed
120
-
-
S&Fin repair 110mm bore PVC (SWR) junction single, (single T) equal or unequal complete all as specified and as directed
5
-
-
S&F in repair 200mm bore PVC (SWR) bend of any radius complete all as specified and as directed
5
-
-
S&F in repair 110mm bore PVC (SWR) bend of any radius complete all as specified and as directed
10
-
-
S&F in repairs 75mm bore PVC (SWR) bend of any radius complete all as specified and as directed
5
-
-
S&F in repairs 75mm dia PVC(SWR) vent cowl complete all as specified and as directed
5
-
-
S&F in repairs 75mm dia PVC(SWR) vent cowl complete all as specified and as directed
1
-
-
S&F grating doom in position, round, 100mm dia of PTMT (minimum weight 25gms) with waste hole fixed with solvent cement complete all as specified and as directed
10
-
-
S&F grating doom in position, round, 125mm dia of PTMT (minimum weight 40gms) with waste hole fixed with solvent cement complete all as specified and as directed
5
-
-
S&F grating doom in position, square, 150mm size, of PTMT (minimum weight 100gms) with waste hole fixed with solvent cement complete all as specified and as directed
5
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements