Military Engineer Services Tender
Download documents of Meghalaya MES Tender
Military Engineer Services - MES Tender
Eprocure
Opening Date28 May 2021
Closing DateCancelled
Tender Amount₹ 10,00,000
Costs
EMD
₹ 20,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2021_MES_446330_1Tender No
GE / SHL / 11 OF 2021-22Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
S&F CGI 0.63 mm thick mild steel sheeting with two corrugations side lap,fixed with coach screws and washers in roofs walls etc with grade of zinc coating 120 gms fixed with l-type or J-type bolts complete all as specified and directed.
40
-
-
S&F PGI 0.63 mm thick mild steel sheeting in ridges hips valley gutters drip and straight flashings(length and girth as fixed) with grade of zinc coating 120gms complete all as specified and directed.
10
-
-
S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed
20
-
-
S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed
5
-
-
S & F of 2.00 mm thick fibre glass reinforced transluscent corrugated sheeting with two corrugation side lap fixed with 'J' type or 'L' type hook bolts and washers as in roof covering etc complete all as specified and directed.
10
-
-
S&F 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc fixed with l-type or J-type bolts complete all as specified and directed
6
-
-
M&L 2nd class hard wood in scantling clean sawn timber fixed complete all as specified and directed
0.11
-
-
M&L for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats creosote oil complete all as specified and directed.
10
-
-
Dismantling boarding of any description and fixed any position with nails complete all as specified and direted.
30
-
-
S&F 40mm thick 2nd class hard wood boarding in floors and skirting plained one side with butt joints and fixed with nails complete all as specified and directed.
5
-
-
S&F 20mm thick 2nd class hard wood boarding in eaves board/fascia plained one side with butt joints fixed with nails complete all as specified and directed.
5
-
-
M&L 6mm thick plywood, grade BWR type BB fixed to timber frame work with nails complete all as specified and as directed.
10
-
-
M&L 6mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face on one side fixed with screws to timber frame work on wall complete all as specified and as directed.
10
-
-
M&L for preparation of New treated wooden surface of any description over 10 cm in width or girth with two coat of french polish incl cleaning and preparing the surface incl a coat of wood filler on new works with two or more coats complete all as specified and as directed.
10
-
-
M&L for 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice laminations and other side balancing white lamination as in kitchen cabinet/cup-board including taking down old unserviceable complete all as specified and directed.
10
-
-
S&F Continuous (piano) hinges,mild steel, bright finish or electrogalvanised with width of flap ( when open) 30 mm complete all as specified and as directed.
3
-
-
S&F in repair Magnet catches for cupboard shutter, brass body and striking plate including letting in all as specified and as directed
10
-
-
S&F Extruded brass handles, 100 mm size, fabricated type, polished all as specified and as directed
5
-
-
S&F in repairs 50mm dia, hard wood knobs , polished, fixed with crews and washer of mild steel, bright finished complete all as specified and as directed.
10
-
-
Dismantling of wall/ceiling boards (fibre, pulp,insulation, etc.) or insulation boards/ slab/blankets, any thickness including cover fillets complete all as specified and as directed.
25
-
-
M&L for Anodised Aluminium snap grid frame work for false ceiling comprising of Gl perimeter channnel 0.55 mm thick with Main T-flange of 25 mm and web of 30 mm fixed to surrounding wall flange using nylon sleeves and SS screws and web 25 mm each , Cross T with flange 25 mm and web 25 mm fixed to main T . Main T is suspended from soffit at approx 1200 mm centre to centre with Gl wire of 4 mm dia ,cleat and steel expansion fasteners , GI frame shall be 60 CM X 60 CM to receive E- board ceiling etc completed all as specified and directed.
15
-
-
S&F 4mm thick E-Board of size 600 mm x 600 mm , prepainted fibre boards ceiling designer / decorative type with different designs as approved , fixed or laid / inserted to timber / GI / aluminium frame work in ceiling flat or slopping etc complete all as specified and as directed.
15
-
-
S&F 4mm thick Non asbestos fibre cement Bldg Board fixed or laid / inserted to timber frame work with nails as in ceiling complete all as specified and as directed.
10
-
-
M&L plain fillets square rectangular or triangular in section clean sawn secured with nails or brads (2nd class hard wood) sectional area exc 13 sqm n exc 25 sqcm complete all as specified and as directed.
30
-
-
M&L for 2nd class hard wood plain fillets bullnosed, splayed, chamfered or rounded on one edge or face in section clean sawn, fixed with screws sec are exc. 6 & n. exc. 13 sqcm complete all as specified and directed
60
-
-
M&L for preparation of new or previously untreated surfaces of ceiling and applying two coats of White wash including necessary preparation etc complete all as specified and as directed.
10
-
-
M&L for preparation of new or previously untreated wooden surface of any description n.exc 10 cm width or girth applying two coats of Synthetic enamel paint over a coat of pink primer all as specified and directed
9
-
-
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.
96
-
-
Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, et complete all as specified and as directed.
14
-
-
M&L for light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in cement sand mortar 1:4 complete all as specified and as directed
8
-
-
All as per above item No 33.00 but as in vertical surfaces such as skirting & dado over and including 10mm thick backing course using cement sand mortar (1:3) complete all as specified and as directed.
4
-
-
M&L for Dark shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in cement sand mortar 1:4 complete all as specified and as directed
1
-
-
M&L for Non-skid ceramic colour tiles 7 to 8 mm thick , (square/rectangular), joint free, area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:4 complete all as specified and as directed.
15
-
-
All as per above item No 36.00 but as in vertical surfaces such as skirting & dado over and including 10mm thick backing course using cement sand mortar (1:4) complete all as specified and as directed.
2
-
-
M&L for Non-skid ceramic colour tiles 7 to 8 mm thick , (square/rectangular), joint free, area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:4 complete all as specified and as directed.
12
-
-
All as per above item No 39.00 but as in vertical surfaces such as skirting & dado over and including 10mm thick backing course using cement sand mortar (1:4) complete all as specified and as directed.
2
-
-
M&L for Glazed ceramic colour tiles of size 450x300mm or 600x300mm , 7mm thick in vertical wall etc set and jointed with neat cement slurry and pointed in white or colour cement to match with the colour of tile over and including 10 mm thick backing course in cement sand mortar 1:3 complete all as specified and as directed.
28
-
-
M&L for machine pressed pre polished factory made pavement chequered cement concrete tiles of size 300 X 300 X 25 mm thick of approved design and colour , set jointed and pointed in neat cement slurry with grey cement and pigment over and including 15 mm thick screed bed in cement sand mortar (1:4) complete all as specified and as directed.
40
-
-
Dismantling stone slabs and tiles of any description or thickness in floors laid bedded and pointed in any mortar etc complete
1.4
-
-
M&L for Machine pressed pre-cast concrete rubber moulded coloured interlocking paver block of any shape and size conforming to IS : 15658-2006 , 60mm thickness, M-35 grade jointed with grey cement and pigment etc complete all as specified and as directed.
10
-
-
M&L for Sand filling under floors or in foundations etc including watering and consolidation etc for laying interlocking paver blocks etc complete all as specified and as directed.
0.5
-
-
M & L Granite (of any tipe) tiles 18-20 mm thick machine cut , bedded and jointed with grey cement and pointed with white cement with admixtures over 20mm thick rendering in CM 1:4 complete all as spefied & directed
4
-
-
Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm thickness (below/above ground level) all as directed.
12.63
-
-
M&L for 40 mm thick PCC (1:2:4) type B-1 using 20mm graded aggregate as in flooring, finished even and smooth without using extra cement etc complete all as specified and as directed.
50
-
-
M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate ) as in path , plinth protection , sub floor etc finishes concrete surface even & smooth or even and rough as required without using extra cement including necessary formwork etc complete all as specified and directed.
75
-
-
M&L for PCC (1:3:6) type C-2 using 40 mm graded stone aggregate as in surface channel and drains complete all as specified and directed.
5
-
-
Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and directed.
60
-
-
Demolition of precast concrete block walling built in cement mortar complete all as specified and directed.
2
-
-
M&L for Precast cement concrete block masonry with solid block PCC, type C1 (1:3:6, using 20mm graded stone aggregate) exc 10 Cm in width and setting in cement sand mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.
1.8
-
-
M&L for Precast cement concrete block masonry with solid block PCC, type C1 (1:3:6, using 20mm graded stone aggregate) 10 Cm in width or girth and setting in cement sand mortar 1:4 complete all as specified and as directed by Engineer-in-Charge.
10
-
-
Demolition of reinforced cement concrete of any description in any position not otherwise described
0.65
-
-
M&L for Precast RCC 1:2:4 type B-1 (using 20mm graded stone aggregate)as in cover slab, landing etc set in CM (1:6) including necessary formwork etc complete all as specified and directed.
0.5
-
-
M&L for RCC (nominal mix) type B-1 (1:2:4) (using 20 mm graded stone aggregate) as in Chajjas complete all as specified and directed.
0.05
-
-
M&L for RCC (nominal mix) type B-1 (1:2:4) (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings and in shelves and the like complete all as specified and directed.
0.1
-
-
M&L for Formwork to sides and soffits of suspended slabs such as roof slabs, floor slabs, landing and similar items (horizontal or sloping), rough finished flat surfaces etc complete all as specified and as directed.
1.5
-
-
Formwork to chullah hoods, cha jjas, troughs and similar items in cluding edges etc complete all as specified and as directed.
0.6
-
-
M & L TMT bars 10 mm dia & over, cut to length, bend to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with & including mild steel wire not less than 0.90 mm dia on securing with clips complete all as specified and directed by Engr-in-Charge.
75
-
-
Dismantling structural steel work of any description not otherwise provided for including doors, gates etc complete all as specified and directed.
1.8
-
-
S&F for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St-240 complete all as specified and directed.
100
-
-
M&L for rolled mild structural steel of Gde Fe-290 (Gde E-165) as in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.
50
-
-
S&F mild steel angles, bands, straps, supports or stays etc, including bolts, if required: clamps; hold fasts; wall ties; wind ties, plates, plain angle cleats for securing purlins, plate washers and similar small articles including all necessary welding, drilling, bolting or riveting, conforming to Fe-290 Gde-E-165 complete all as specified and directed.
30
-
-
M&L for mild steel, plain black sheet 1.00 mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.
2
-
-
Excavation in post holes each n.exc. 0.5 cum in soft/loose soil getting out returning, filling in and ramming earth or broken rubble mixed with earth around in layer n.exc. 25 cm, watering and removing surplus soil to a distance n.exc. 50 mtr and making good surface complete all as specified and directed.
6
-
-
M&L for PCC (1:3:6), type C1 (using 20 mm graded stone aggregate) as in foundation filling and mass concrete including all necessary form work complete all as specified and directed.
0.73
-
-
Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key, scrubbing down with water, etc all as specified and directed.
60
-
-
M&L for Rendering, 15 mm thick plaster in cement sand mortar ( 1:4), in two layers, top 5 mm thick with approved liquid Water proofing compound @ 3% by the weight of cement or as per manufacturers instructions over a layer of 10 mm thick base coat including finishing the surface even and smooth without using extra cement, complete all as specified and as directed by Engineer-in-Charge.
Note WPC shall be measured and paid separately.
60
-
-
M&L for rendering 10mm thick in CM (1:6) on fair faces of brick or concrete surfaces including finishing even & smooth without using extra cement complete all as specified and directed.
10
-
-
M&L for 5mm thick plaster in CM (1:3) on fair faces of concrete surfaces of ceiling including finishing even & smooth without using extra cement complete all as specified and directed.
10
-
-
Supply only integral water proofing compound, ISI marked.complete all as specified and as directed.
8
-
-
M&L for preparation of new plastered surfaces of wall and applying two coats of cement based paint over a coat of primer all as specified.
60
-
-
M&L for preparation of new plastered surface of walls and applying two coats of acrylic distemper over a coat of alkali resistant priming paint complete all as specified and directed.
10
-
-
M&L for preparation of new ceiling surfaces and applying three coats of white wash complete all as specified and directed.
10
-
-
Taking down Chowkhats or frames exc 1.5 Sqm but n.exc 4 Sqm each but with shutters (without taking off shutters from the frame) including builders hardware each complete all as specified and directed.
8
-
-
Taking down Chowkhats or frames n.exc 1.5 Sqm each but with shutters (without taking off shutters from the frame) including builders hardware each complete all as specified and directed.
8
-
-
Taking down shutters of any description exc. 1 Sqm and n. exc. 2 Sqm each and removing from site complete all as specified and directed.
8
-
-
Taking down shutters of any description n. exc. 1 Sqm each and removing from site complete all as specified and directed.
8
-
-
Taking down shutters of any description exc. 1 Sqm and n. exc. 2 Sqm resecuring or easing & adjusting refixing in same opening complete all as specified and directed.
5
-
-
M&L for 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints,complete all as specified and directed by Engineer-in-Charge.
0.14
-
-
S&F Pressed steel frames Size 125mmx60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed by Engineer-in-Charge.
10.4
-
-
M&L for PCC 1:3:6 type C1 (using 20mm graded aggregate) as in steel frame filling/hold fast blocking incl necessary form work complete all as specified and directed.
0.2
-
-
S&F in repair mild steel as a small article as a hold fast or similar items complete all as specified and directed.
10
-
-
S&F 30mm thick flush shutter solid core construction with block board core and plywood face panels, commercial type on both sides .etc complete all as specified and as directed.
4.2
-
-
S&F 35 mm thick 2nd class hard wood plain framed panelled shutter any number of panels with panels of timber of veneered particle board with commercial face veneers flat on both side with feather edged etc complete all as specified and as directed.
4.2
-
-
S&F 35 mm thick, 2nd class hard wood, glazed and skeleton shutter, open rebated and prepared to receive glass or gauge without sash bars , divided in to squares and edges of framing plain chamfered or rounded, fitted with cut or mitred beads for securing glass or gauge etc as specified in SSR Part-I section 8 clause 8.24 (a) complete all as specified and directed.
4.2
-
-
M&L 30mm thick 2nd class hard wood factory made glazed and skeleton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) complete all as specified and directed.
5.6
-
-
M&L 30mm thick 2nd class hard wood factory made glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. without sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) complete all as specified and directed.
5.6
-
-
S&F in repairs Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.
2
-
-
S&F in repairs in steel ventilator with top hung shutter with or without glazing bar, incl hinges, fixing lugs,steel peg stay, complete all as specified and as directed
2
-
-
M&L for preparation of new or previously untreated surfaces of wood and wood based materials of any description not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer complete all as specified and as directed.
30
-
-
M/L 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pan complete all as specified and as directed. .
2
-
-
S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.
4
-
-
S&F factory made pre laminated solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with single piece extruded pvc profile both side prelam PVC sheet 'C' channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and 5mm thick both side prelam single piece extruded pvc profile for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of both side prelam 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and shown on drawing given in SSR Part II. The width of stiles & rails shall be in proportion to the width of the door shutter as given in SSR Part I.
4
-
-
S&F pre laminated solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam single piece extruded pvc profile and edgs will be painted to match with prelam sheet , PVC sheet are to be reinforced with 19x19mm MS square tube EPDM rubber gasket weather seal shall be provided through out the frame. The profile shall be mitre cut at two corners and joint by insrting 2 nos of 150mm long backets of 15mmx15mm MS square tube inside the 19mmx19mm MS square tube and suitably screwed and fixing in opening as per specification & drawing complete all as specified and directed.
10
-
-
S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing
4
-
-
S&F Mild Steel Butt hinges, medium weight, cold rolled, 100mm size ISI Marked complete all as specified and directed.
90
-
-
S&F Mild Steel Butt hinges, medium weight, cold rolled, 75mm size ISI Marked complete all as specified and directed.
30
-
-
S&F Extruded aluminium anodised bow handles of 150 mm length etc complete all as specified and as directed.
46
-
-
S&F Extruded aluminium anodised bow handles of 100 mm length etc complete all as specified and as directed.
20
-
-
S&F Aluminium anodised, barrel tower bolts of extruded section 200 mm length complete all as specified and as directed.
46
-
-
S&F Aluminium anodised, barrel tower bolts of extruded section 100 mm length complete all as specified and as directed.
40
-
-
S&F in repair 4 leversBrass Mortice lock,vertical type,100mm length complete all as specified and directed
5
-
-
S&F 300 mm long, Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed
10
-
-
S&F powder coated anodized aluminium frame for doors, windows, ventilators, partitions with one or more rebates including joining cleats for fixing etc complete all as specified and as directed.
35
-
-
S&F powder coated ,anodised aluminium window and ventilator shutters fixed type without sash bars, aluminium secton weighing 0.55 kg/m incl necessary joining cleats glazing clips, rubber packing , anodised aluminium snap beading , screws complete
4
-
-
S&F Power coated, anodised door shutters , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , handles 2 nos in each door , hinges , anodised aluminium snap beading screws etc complete all as specified
4
-
-
S&F Powder coating anodised window and ventilator shutters side hung/sliding type without sash , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , anodised aluminium snap beading screws ,anodised aluminium fittings such as peg stays 150 mm long(1 no) hinges type B-21 100 mm long (2 no) suitable handle (1 no ) complete as specified
4
-
-
S&F Sheet glass, 4mm thick ordinary quality, in squares,exceeding 0.50 sqm in each pane including rubber packing and aluminium beadingcomplete all as specified and directed
3
-
-
S&F Sheet glass, 5.50mm thick ordinary quality, in squares,exceeding 0.50 sqm in each pane including rubber packing and aluminium beadingcomplete all as specified and directed
3
-
-
M&L 12mm thick prelaminated particle board, interior grade prelaminated both side with decorative choice laminations ,fixed with screw etc complete all as specified.
8
-
-
S&F in repair Aluminium extruded section door closer hydraulially regulated, designation No 3, universal type suitable for door shutter of 851 to 1000mm width and of weight of between 61 to 80 kg and fixed all as specified (ISI Marked)
4
-
-
S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width aperture 1.40 mm and fixed with stainless steel wire staples
8
-
-
M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top:-
(i) Taking out old roof treatment and roughening the same old concrete slab by picking, sweeping clean and washing down with water to remove dust etc. and applying cement slurry @ 3kg/Sqm
(ii) Screed bed or bedding layer of mortar 15 mm thick in CM (1:4) for laying as in roof slab with mixing of WPC and surface finished fare and smooth without using extra cement. (Note: WPC shall be measured and paid for under separate items)
(iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25ltr /Sqm conforming to IS:3384-1986.
(iv) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be applied by torch application over bituminous primer as specified. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction.
(v) Applying one coat of aluminum paint over the APP modified membrance @ 0.11Kg/sqm. (NOTE:- The work of water proofing treatment shall be got executed through expert team of manufacturers or authorised applicator of manufacturer contractor shall be submitted documentary evidence in support of applicator engaged for approval of GE.)
30
-
-
S&F in repair Vitreous China wash down (EWC) water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) but including PVC water closet seat cover closed pattern with flat bottom and cover with PVC hinge device, flushing pipe, fixing bolt for pedestal pattern and making good to disturbed surfaces of floor etc complete all as specfied and directed. Make:- Prayag cat part no.4022 or equivalent make of Parryware / Hindware.
2
-
-
S&F in repair Plastic Water closet seat cover, black / white closed pattern with flat bottom, and cover and mild steel chromonium plated or aluminised hinging devices, complete all as specifed and directed. Make : Prayag cat part no. 513 or equivalent make of Parrywire / Hindware .
5
-
-
S&F in repair Vitreous china squatting pan of Orissa Pattern of size 580x 440 mm ,white with ‘P’ or ‘S’ trap , front or back inlet but excluding flushing cistern and flush pipe including placing in position in floor and embedded in cushion of PCC type E2 ( using 40 mm graded crushed stone aggregates), 1:5:10 and finishing the top surfaces to match with the existing flooring complete all as specified and as directed .Make:- Prayag cat part no. 4055 or equivalent make of Pearl / Hindware.
2
-
-
S&F in repair PVC (Plastic polymer flushing Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 litres, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete all as directed by Engineer-in-Charge .Make:- Prayag cat aprt no. 503 or equivalent make of Pearl/ Hindware.
5
-
-
S&F in repair Vitreous china wash hand basin, white, flat back of size 550 mm x 400 mm including bracket, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia, PVC flexible waste pipe of adequate length and dia and PVC connection 15mm size 450mm length with PTMT nuts, complete all as specified and as directed by Engineer-in-Charge .Make:- Prayag cat aprt no. 4645 IRIS or equivalent make of Pearl/ Hindware.
5
-
-
Taking up or down steel tubing with connections of 15 mm bore pipe including cleaning for refixing or removal from site with all fittings complete all as specified and directed.
40
-
-
Taking up or down steel tubing with connections of 20 mm bore pipe including cleaning for refixing or removal from site with all fittings complete all as specified and directed.
10
-
-
S&F GI tubing 15mm dia medium grade with all necessary GI fittings ,fixed in wall, ceiling or floor with necessary clamp or hook complete all as specified and as directed.
40
-
-
S&F GI tubing 20mm dia medium grade with all necessary GI fittings ,fixed in wall, ceiling or floor with necessary clamp or hook complete all as specified and as directed.
10
-
-
S&F in repair kitchen sink with drainage board made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm ,bowl size 410 mm x 360 mm x 160 mm complete all as specified and directed.Make:- Prayag / Nirali / Hindware
1
-
-
S&F in repair Pillar tap,15 mm bore, brass chromium plated, screwed down, high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engr-in-Charge Make:- Prayag cat part no.7602 or equivalent make Jaquar/Cera/Hindware
5
-
-
S&F in repairs CP Bib tap 15 mm bore, cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down, high pressure, screwed for iron pipe complete all as specified and as directed. . Make:- Prayag Cat part No.7606 or equivalent model from make Jaquar/Cera/Hindware
5
-
-
S&F in repairs CP Stop cock ( concealed type) ,15 mm bore, fancy type, chromium plated, screwed down, high pressure, screwed for iron pipe complete all as specified and as directed. . Make:- Prayag Cat part No.9218 or equivalent model from make Jaquar/Cera/Hindware
5
-
-
S&F in repairs CP angular Stop cock ,15 mm bore, fancy type, chromium plated, screwed down, high pressure, screwed for iron pipe complete all as specified and as directed. . Make:- Prayag Cat part No.8010 or equivalent model from make Jaquar/Cera/Hindware
5
-
-
S&F in repairs PVC connection 15mm size, 450 mm long with PTMT nuts complete all as specified and as directed.
10
-
-
S&F in repair Bevelled edge mirror, of size 600mm x 450mm x5mm of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as directed.
10
-
-
S&F in repair 15 mm bore brass CP center hole basin mixer for mixing hot and cold water ,fancy type etc complete all as specified and directed. Make : Prayag cat part no. 7650 or equivalent modal of Sona / Hindware / Jaquar.
5
-
-
S&F in repair kitchen plate rack made of stainless steel sheet 1.00 mm thick of over all size 31'' x 30'' x 10'' fixed to wall with brass screws etc complete all as specified and as directed.Make:- Prayag Cat part no. P-346 or Bluestar cat part No BSKPR-314 or equivalent make of Hindware / Nirali
1
-
-
S&F in repair Rotational moulded HDPE polyethylene 500 ltrs capacity water storage tanks three layered, (ISI marked) (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball valves 20mm dia high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball including 20mm dia GI medium grade over flow pipe, approx lenght 1.5 mtr, 25 mm dia wash out pipe with pluged at one end complete all as specified and directed.
4
-
-
S&F in repair rotational moulded polyethylene 1000 ltrs capacity water storage tanks , three layered, (ISI marked) (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball valves 20mm dia high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball including 20mm dia GI medium grade over flow pipe, approx lenght 1.5 mtr, 25 mm dia wash out pipe with pluged at one end complete all as specified and directed.
2
-
-
Cleaning and removing all scale and dirt etc from PVC/RCC/MS overhead tanks by using wire brush, bleaching powder or lime etc of required quantity and washing with clean water from tank and mouth of circulating pipe after disconnecting existing tanks, setting aside (or lowering if required) for repair, cleaning, etc and hoisting if required, reconnecting and refixing in position of capacity exc 500 n.exc 1000Ltrs incl writing "TC on -DD/MM/YY" with white synthetic enamel paint with 5 cm font in capital letters etc complete all as specified and directed.Note:- Proper record of cleaning of tank done under subject item shall be maintained in a register by sub division ,duly authenticated by user or user rep and Engineer-in-charge and shall be produced at the time of claiming any payments.
10
-
-
Cleaning and removing all scale and dirt etc from PVC/RCC/MS overhead tanks by using wire brush, bleaching powder or lime etc of required quantity and washing with clean water from tank and mouth of circulating pipe after disconnecting existing tanks, setting aside (or lowering if required) for repair, cleaning, etc and hoisting if required, reconnecting and refixing in position of capacity exc 250 n.exc 500Ltrs incl writing "TC on -DD/MM/YY" with white synthetic enamel paint with 5 cm font in capital letters etc complete all as specified and directed.Note:- Proper record of cleaning of tank done under subject item shall be maintained in a register by sub division ,duly authenticated by user or user rep and Engineer-in-charge and shall be produced at the time of claiming any payments.
10
-
-
S&F in repair float valve of size 20mm, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe all as specified and directed
20
-
-
S&F in repair float valve of size 25mm, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe all as specified and directed
10
-
-
S&F in repair PVC nipple of size 15mm dia bore suitable for HDPE water storage tank etc complete all as specified and as directed.
5
-
-
S&F in repair PVC nipple of size 20mm dia bore suitable for HDPE water storage tank etc complete all as specified and as directed.
5
-
-
S&F in repair Gun metal gate valve class I (ISI) marked with iron wheel head, screwed both ends for iron pipe, suitable for 20 mm bore of pipe etc complete all as specified and directed by Engr-in-Charge.
5
-
-
S & F in repair 110 mm bore PVC (SWR) bend of any radius with access door complete all as specified and directed.Make:- Prince / Supreme.
5
-
-
S & F in repair 110 mm bore PVC (SWR) pipe, single socketed, in any length with rubber ring joint fixed to walls including clamps for securing pipe complete all as specified and directed .Make:- Prince / Supreme.
20
-
-
S&F in repairs peg set of six, chromium plated, back plate including chromium plated fixing screw complete all as specified and directed.
16
-
-
S&F in repair 25 mm dia aluminium drapery rod with wooden finish, decorative, including brackets, decorative finials at both ends (minimum) in one opening complete all as specified and directed.
35
-
-
S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified and directed.
10
-
-
S&F 300mm long MS Helical door spring Welded to steel /Fixed to wooden door frame including roller and roller plate etc of approved quality complete all as specified and directed.
10
-
-
Hacking out old broken glass (any thickness, size, quality or description) from wooden frame including taking out old wooden beads complete all as specified and directed.
2
-
-
S&F 3 mm thick figured glass, pin head type and glazing with oil putty or wooden beads in squares n.exc 0.5 sqm in each pane complete all as specified and directed.
2
-
-
M&L for Complete removal of existing old treatment as in wall and applying two coat of cement base paint on wall including one coat of alkali-resistant primer on plastered surfaces all as specified and directed.
200
-
-
M&L for preparing old decorated plastered or unplastered surfaces of wall including cornices,pilastera and other wall features etc by brooming down or steel wire brushing scrapping down to remove smoke soot, moulds, moss and efflorescence salt and treating oil and greasy spot etc and applying two coat of white wash on the wall all complete as specified and as directed.
250
-
-
M&L for preparation of old decorated plastered surfaces of ceiling including cornices, plasters etc and applying one coat of white wash complete all as specified and directed.
440
-
-
M&L for preparation of old decorated plastered surfaces of walls and applying two coat of plastic emulsion paint over a coat of primer all as specified and deirected.
50
-
-
M&L preparation of old surfaces of walls and applying one coat of Oil bound distemper etc complete all as specified and as directed.
700
-
-
M&L for complete removal of existing treatment of wall and applying two coats of Oil bound distemper, over 1 mm thick wall care putty including necessary preparation of wall surfaces complete all as specified and as directed.
102
-
-
M&L for preparation of old decorated plastered surfaces of walls and applying one coat of plastic emulsion paint all as specified and deirected.
45
-
-
M&L Exterior emulsion paint ( weather coat), two coats over a coat of alkali resistant primer on external surfaces including complete removal of existing treatment over wall and preparation of surfaces even and smooth complete all as specified and directed.
100
-
-
M & L for preparation of old treated wooden surface of any description over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed
350
-
-
M&L for preparation of old concrete surfaces of wall/ceiling and applying one coat of synthetic enamel paint all as specified and directed.
245
-
-
M&L for preparation of old painted wooden surfacaes of any descripion n.exc 10cm width or girth and applyinjg one coat of synthetic enamel paint all as specified and directed.
100
-
-
M&L for preparation of old steel surface and applying one coat of synthetic enamel paint on steel surface.
120
-
-
M&L for preparation of old painted surfaces of CGI Sheet roof of any description of over 10cm width or girth and applying one coat of anti corrosive roof paint complete all as specified and as directed.
150
-
-
M&L for Acrylic distemper, one coat over old treated ceiling surfaces including necessary preparation of old surfaces complete all as specified and as directed.
500
-
-
M&L French polish, one coat over old wooden painted surfaces of any description over 10 Cm width or girth including necessary preparation of old surfaces with a coat of wood filler with two or more coats complete all as specified and as directed.
50
-
-
M&L painting to new steel surfaces of any description, over 10cm in width or girth, steel Sqm surfaces in two coats of synthetic emamel paint over a coat of red-ocide primer not otherwise discribed.
20
-
-
S & F in repairs Vitreous China EWC (P or S type) including seat cover closed pattern single piece size 755x365x655 complete of make Jaguar Cat Part No :- LYS-WHT-38851P180UFSM/ LYS-WHT-38851S300UFSMN or equivalent
1
-
-
S&Fin repairs ball bearing drawer channel of size 600 mm long complete all as sspecified and as directed by Engr-in-charge
4
-
-
S&F in repair CP over head showers dia around 100 mm round shape single flow ( ABS body chrome plated with grey face plate ) with rubit cleaning system with CP shower arm dia 20 mm long round shape without bend for wall mounted showers wall flange etc complete all as specified and as directed. Make: Jaquar Cat.No OHS-CHR-1989 with SHA-CHR-49483 or equivalent model from make Prayag/Cera/Hindware
1
-
-
S&F in repair CP single lever wall mixer 3-in-1 system with provision for bath hand shower and overhead shower with 115 mm long bend pipe connecting legs and wall flange ( without hand & overhead shower) etc complete all as specified and as directed. Make: Jaquar Cat.part No OPP-CHR-15125PM or equivalent model from make Prayag/Cera/Hindware
1
-
-
S&F in repair 15 mm bore health faucet cock with flexible pipe 1 meter long etc complete all as specified and as directed. Make: Jaquar Cat.part No ALD-CHR-565 or equivalent model from make Prayag/Cera/Hindware
1
-
-
S&F in repair CP soap dish holder fixed on wall with CP screws etc complete all as specified and as directed. Make: Prayag Cat.part No BA-05 or equivalent model from make Jaquar/Cera/Hindware
2
-
-
S&F in repair stainless steel Toilet paper roll holder with fixed on wall with CP screws etc complete all as specified and as directed. Make:Jaquar Cat.part No AKP-35755PS or equivalent model from make Prayag/Cera/Hindware
1
-
-
S&F in repair stainless steel Towel ring square shape with round flange with fixed on wall with CP screws etc complete all as specified and as directed. Make:Jaquar Cat.part No ACN-CHR-1121N or equivalent model from make Prayag/Cera/Hindware
1
-
-
S&F in repair Sheet glass corner shelf assembly with ABC bracket complete all as specified and as directed. Make- Jaquar Cat Part No CAN-CHR-1173 or equivalent model from make Prayag/Cera/Hindware
2
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements