Military Engineer Services Tender

Returning filling in soft/loose soil, including, spreading, levelling, watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

Removing of surplus soil to a distance not exceeding 50 metre and deposited where directed at a level not exceeding 1.50 metre above the starting point all as specified.

Supply and laying, connecting, testing, commissioning HT UG cable XLPE Insulated,armoured, electric power cables (heavy duty) 11 KV grade conforming to IS 7098 with aluminium conductor multi-strand of cross-sectional area 120 Sqmm 3.5 Core laid in trenches / ducts/ inside protection pipe including cable glands, lugs and suitable size of MS saddle clips etc.including taking out old unserviceable cable all as directed by Engr-In-Charge. Make: Polycab(ISI Marked)/ Finolex(ISI Marked)/ Nicco (ISI Marked) Note:-(a) Excavation, sand cushioning, bricks, GI Pipe laying, road cutting shall be measured and paid separately.

Material and labour as in replacement for outdoor type Cold shrinkable cable end termination jointing kit for HT 11000 Volts(Earthed) grade cable of 95 sqmm 3 core complete with jointing material and accessories complete all as directed by Engineer-In-Charge. Make: M-Seal/ Cab-Seal/ Denson/ Raychem/ Birla 3M

Material and labour as in replacement for outdoor type Cold shrinkable cable end termination jointing kit for HT 11000 Volts(Earthed) grade cable of 120 sqmm 3 core size complete with jointing material and accessories complete all as directed by Engineer-In-Charge. Make: M-Seal/ Cab-Seal/ Denson/ Raychem/ Birla 3M

Material and labour as in replacement for indoor type Cold shrinkable cable end termination jointing kit for HT 11000 Volts(Earthed) grade cable of 95 sqmm 3 core size complete with jointing material and accessories complete all as directed by Engineer-In-Charge. Make: M-Seal/ Cab-Seal/ Denson/ Raychem/ Birla 3M

Material and labour as in replacement for indoor type Cold shrinkable cable end termination jointing kit for HT 11000 Volts(Earthed) grade cable of 120 sqmm 3 core size complete with jointing material and accessories complete all as directed by Engineer-In-Charge. Make: M-Seal/ Cab-Seal/ Denson/ Raychem/ Birla 3M

Material and labour as in replacement for heat shrinkable outdoor type straight through jointing kit for HT 11000 Volts(Earthed) grade cable of 95 sqmm 3 core size complete with jointing material and accessories complete all as directed by Engineer-In-Charge. Make: M-Seal/ Cab-Seal/ Denson/ Raychem/ Birla 3M

Material and labour as in replacement for heat shrinkable outdoor type straight through jointing kit for HT 11000 Volts(Earthed) grade cable of 120 sqmm 3 core size complete with jointing material and accessories complete all as directed by Engineer-In-Charge. Make: M-Seal/ Cab-Seal/ Denson/ Raychem/ Birla 3M

Supply, lay and fix 100 mm bore galvanized iron tubing (light grade) including all fittings and laid in trenches, walls and ceilings or laid in floors complete all as specified and directed. Make:- Jindal/ TATA/ Prakash Note: Excavation shall be measured and paid in separate item

Supply and filling for dry sand in cable protection trenches before and after the cables are laid, for sand cushioning to cables complete all as specified and directed. NOTE : thickness after punning of sand shall be (minimum as specified in SSR) measured and paid in this item.

Supplying and laying un-reinforced precast concrete cable cover, class HVP,type 1 with peak, size 300 mm x 180 mm x 40 mm complete all as specified.

Material and labour for Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified.

Material and labour as in replacement pin type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 150mm height, 150mm dia for 11000 volts grade complete all as specified. Make: BHEL/ Jaypuriya Brothers/ Pactil/ Southern Insulators

M & L in replacement for disc type insulator, porcelain, vitreous 145mm high and 255 mm dia ball and socket type, white brown or green ' Single disc' assembly for tension with tension clamps for conductors, working pressure 11000 Volts complete all as specified and directed. Make: BHEL/ Jaypuriya Brothers/ Pactil/ Southern Insulators

Supply & fix PVC insulated aluminium conductor steel reinforced (ACSR) of suitable size for four pole and two structure for connection of gang operated switch and DO switch complete all as specified and directed. Note: Each run of conductor shall be measured and paid. Make: Allind/ ICC/ Bharat Conductor/ VK conductors/ NICCO.

M & L in replacement drop out expulsion fuse assembly complete set for 03 phases, 11000 Volts, above 50 & upto 100 Amps complete all as specified and directed. Make: L&T/ Legrand/ ABB/ Siemens/ GE/ Schnieder

S & F in replacement Lightening arresters non linear type complete with all fitting, transmission class, discharge capacity 65 KA, 11000 volts grade including clamps nut, bolts & washers and connecting to earth with GI strip/wire complete all as specified and directed. Make: Oblum/ BHEL/ Elpro/ Jaypuriya Brothers

Supply, installing, testing and commissioning of Air-break, gang operated, triple pole switch, outdoor, horizontal mounting type (ISI marked), mechanically operated, mounted on insulators for current rating upto 200 Amps complete with fuse mounts, fuse carriers and HT fuse elements and frame work with operating mechanism worked from ground level, with locking arrnagments including Godrej pattern 65mm pad locks with two keys, complete suitable for HT 11 KV, 50 Hz AC supply and making necessary electric connections, complete all as directed. Make: Pactil/ BHEL/ Jaypuriya Brothers/ Elpro/ Atlas

M & L for earthing complete with galvanized steel earth plate 60 cm X 60 cm X 6 mm thick buried vertically in ground to depth not less than 2.25 metres deep below ground level, with top edge of earth plate not less than 1.5 m below ground level, connected to galvanized iron strip 32x6mm earth lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel besides welding at all joints as shown in drawing and including excavation and earth work, GI pipe light grade 40mm bore for protection of earth wire and connected to continous earth lead on pole/test point, supplying and laying charcoal dust common salt PCC 1:2:4 type B1, chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced with 6mm dia round bars @ 75mm C/C both ways with MS handle 12mm dia, PGI/CI funnel and wire mesh, 20mm dia GI pipe medium grade for watering all as shown in electrical plate No 5 on srl page No 497 of SSR Part I (2009) drawing and connection to earth test point including testing and including dismantling and taking out old earthing complete all as specified and directed. Note : (i) The cost of earth lead /strip and GI pipe for protection of earth lead/strip upto 7.5m is included in the quoted rate. (ii) The cost of excavation, earth work is included in the quoted rate.

M & L for earthing complete with Copper earth plate 60 cm X 60 cm X 3.15 mm thick buried vertically in ground to depth not less than 2.25 metres deep below ground level, with top edge of earth plate not less than 1.5 m below ground level, connected to copper earth strip of size 20mmx3mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel besides welding at all joints as shown in drawing and including excavation and earth work, GI pipe light grade 40mm bore for protection of earth wire and connected to continous earth lead on pole/test point, supplying and laying charcoal dust common salt PCC 1:2:4 type B1, chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced with 6mm dia round bars @ 75mm C/C both ways with MS handle 12mm dia, PGI/CI funnel and wire mesh, 20mm dia GI pipe medium grade for watering all as shown in electrical plate No 5 on srl page No 497 of SSR Part I (2009) drawing and connection to earth test point including testing and including dismantling and taking out old earthing complete all as specified and directed. Note : (i) The cost of earth lead /strip and GI pipe for protection of earth lead/strip upto 7.5m is included in the quoted rate. (ii) The cost of excavation, earth work is included in the quoted rate.

M & L in replacement Earth continuity conductor galvanised iron strip 32x6mm buried in ground, to be fixed on porcelain insulator with GI nuts, bolts and washers or any other indicated situation with all accessories complete all as specified and as directed.

M & L in replacement Earth continuity conductor copper strip of size 20 x 3.00mm buried in ground, to be fixed on porcelain insulator with GI nuts, bolts and washers or any other indicated situation with all accessories complete all as specified and as directed.

M & L for PCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in pedestal of poles, platforms of transformers etc including weathering, slightly rounded or chambered angle and throating including use and waste of necessary form work finishing all exposed faces of concrete even and smooth using extra cement complete all as specified and directed.

M & L in replacement Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hexagonal head screw complete all as specified and directed

Supply and install in replacement of steel tubular swaged poles type 410 SP-55 (11 mtr long) complete with CI base plate and finial taper plug,bolts, nuts and screws as specified all as directed by Engr-in-Charge. Note :- Excavation and earth work only will be measured separetely all other accessories and work deemed to be included in quotyed rates. Make: Jindal Steel/ National Tubing Co/ Bombay Tube & Store/ Calcutta Poles & Tubes

Taking down carefully Gang operatedair break switch 11 KV, 200 Amps rating from two pole / four pole structure by disconnecting all electrical connection for repairing. Split opening for carrying out repair work including replacement of burn out/ defective parts and refixing at site duly oiling/ greasing moveable parts and replacement of nuts, bolts, washers and suitable/ existing sizes of jumpers not less than 70 Sqmm cable, 3.0 mtrs long all as specified and directed by EIC. Note:- The spares shall be measured and paid under respective items.

Supply and fixing (in replacement) porcelain vitreous brown or white or green insulator suitable for HT 11KV GOD. Make: Pactil/ BHEL/ Jaypuriya Brothers

Supply and fixing (in replacement) male contact/ moving contact blade suitable for HT 11KV GOD all as specified and directed by EIC. Make: Pactil/ BHEL/ Jaypuriya Brothers

Supply and fixing (in replacement) female contact/ fix contact jaw suitable for HT 11KV GOD all as specified and directed by EIC. Make: Pactil/ BHEL/ Jaypuriya Brothers

Supply and fixing (in replacement) tinned copper flexible jumpers suitable for 200 Amps rating HT 11KV GOD all as specified and directed by EIC. Make: Pactil/ BHEL/ Jaypuriya Brothers

Supply and fixing (in replacement) MS jumper carrier complete suitable for HT 11KV GOD all as specified and directed by EIC. Make: Pactil/ BHEL/ Jaypuriya Brothers

Supply and fixing (in replacement) back connector plate suitable for HT 11KV GOD all as specified and directed by EIC. Make: Pactil/ BHEL/ Jaypuriya Brothers

Dismantling the HT/ LT cable from pole mounted ( four pole / two pole structure) transformer by chain pully block and shifted to transformer on plinth foundation incl. reconnection of LT/HT cable and testing complete all as specified and directed by E-I-C.

Material and labour for hard core of gauge not exceeding 63 mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface complete all as specified

M&L for brick work sub class "B" straight,or curved on plan exc. 6 M mean radius built all as directed by Engr-in-Charge.

Supply only ISI mark rubber matting conforming to IS 15652:2006 suitable for 11 KV AC RMS voltage,45 KV dielectric strength of minm thickness 2.5 MM . Make: Jaipuria

Supply only Rubber Hand gloves ISI Mark suitable upto 22 KV KV AC RMS voltage .Make : Jaipuria

M&L Rendering 10mm thick on fair faces of brick work or concrete sur faces with cement plaster1:6 Mix as directed