Military Engineer Services Tender

Taking down door frame or chowkhats or frames exc. 1.5 sqm but n.exc 4.0 sqm each (without taking off shutter from the frame) complete all as specified and directed.

Taking down door frame or chowkhats or frames n exc. 1.5 sqm each (without taking off shutter from the frame), complete all as specified and directed.

Taking down wall panelling and similar work all as specified and directed.

S&F Hollow PVC wall panelling and lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on GI frame, complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as per specification and directed

M&L for 15mm thick rendering in CM (1:4) in two layers mixed with liquid water proofing compound as per manufacturers instruction in top layer 5 mm thick finishing the surfaces even and smooth without using extra cement complete all as specified and directed. Note: Liquid water proofing compound shall be measured and paid seperately.

Supply only integral WPC ( Integral waterproofing liquid admixture for cement mortar) and application as per manufacture instruction all as specified and directed by Engr-in-charge.

M&L for rendering 15mm thick in cement mortar (1:6) internal surfaces on other than fair faces of brick work or concrete surfaces, complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying two coat of distemper oil emulsion including 1.5mm thick internal wall putty with alkali resistant primer, complete all as specified and directed.

M&L for preparing surfaces of newly plastered of walls and applying two coat of acrylic smooth exterior paint including 1.5mm thick external wall puty with alkali resistant primer, complete all as specified and directed.

M&L for Non - skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but notexceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed.

M&L for vitrified ceramic tiles 10 mm thick (square/ rectangular) light shade polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed.

M&L for 15mm thick screed bed or bedding laying in cement mortar (1:6), for as in floor finishes, complete all as specified and as directed.

Supply and fix aluminium (powder coated) Ventilator frame with side hung Shutter(bottom Half Portion fixed and top half portion openable shutte with 4.0mm thick frosted glass ) including all necessary joining cleats, hold fast, rubber gasket, snap beading and locking arrangements,Hinges,Tower bolt fixed with screws to wall etc. complete and glazing with and including 4 mm thick frosted glass to aluminium frame work using rubber gasket and including stainless steel wire cloth of 0.36 mm dia & average width of aperture 1.40mm with staple or suitable fillets wire mesh fitted with screws and washers etc including aluminium grill of thickness 5mm and opening not exceeding 75mmx75mm etc completee with the following section of frame and shutter (A) Sections for shutter - section 41 x 20 x 1.50 mm thick (B) Section for frame 63.5 X 38.1X 1.53mm thick Note:- (a) Quoted rate are deemed to inclusive of taking down ventilator/window of any size and any description and making good to match the existing surface as per existing sch of finishes.

Supply and fix aluminium (powder coated) three track sliding window frame with shutters with ( 2 nos glazed and one wire gauzed shutter)including all necessary joining cleats, hold fast, rubber gasket, snap beading and locking arrangements fixed with screws to wall etc. complete and glazing with and including 5 mm thick tinted glass to aluminium frame work using rubber gasket and including stainless steel wire cloth of 0.36 mm dia & average width of aperture 1.40mm with staple or suitable fillets wire mesh fitted with screws and washers etc including aluminium grill of thickness 5mm and opening not exceeding 75mmx75mm etc completee with the following section of frame and shutter (A) Sections for shutter (i) 'H' section 39 x 20 x 1.50 mm thick (ii) 'Interlock' section 39 x 20 x 1.50 mm thick (iii) 'Edge & Bottom' section 41 x 20 x 1.50 mm thick (B) Section for frame (i) Top & Sides 92 X 29.50X 1.50mm thick (ii) Bottom 92 X 29.70 X 1.50mm thick complete all as specified and directed . Note:- (a) Quoted rate are deemed to inclusive of taking down ventilator/window of any size and any description and making good to match the existing surface as per existing sch of finishes.

S&F false ceiling of designer tile ivory painted (high pressure steam cured ) of 4mm thick (as per IS: 14862) of size 595x595mm and any one of the design (cascade or electra) in true horizontal level. Suspended on inter locking metal grid of hot dipped galvanized steel section (galvanized @120gms both side inclusive and black painted groove on all T webs)consisting of main T runner with suitably spaced joints to get required length and 15x32mm made of 0.3mm thick sheet spaced at 1200mm c/c and cross T of size 15x32mm made of 0.3mm sheet 1200mm long spaecd between main T at 600mm c/c to form a grid of 1200x600mm and secondary cross T of length 600mm and size 15x32mm made of 0.3mm thick sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including required cutting/making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.Main T runners to be suspended from trusses/ceilings using suitable suspension arrangement as per manufacturers instructions/literature. GI adjustable wire of 4mm dia with galvanized butterfly level clips spaced at 1200mm c/c along main T bottom exposed width of 15mm of all T section of 4mm dia GI wire shall be pre-painted with with polyster paint and black painted groove at centre of size 4mm depth and 4.5mm width, including taking down old false ceiling board of any description alongwith rails and connecting items, complete all as specified and directed.

S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ridge/ cladding to wall, fixed with self tapping screw in roofs, complete all as specified and directed.

M&L for complete removal of existing treatment on walls and applying two coat of distemper oil emulsion including internal wall putty 1.5mm thick with alkali resistant primer,, complete all as specified and directed.

M&L for complete removal of existing treatment on walls and ceiling and applying one coat of acrylic smooth exterior paint (weather coat) including 1.5mm thick external wall puty with alkali resistant primer, complete all as specified and directed.

Supply & Fix weather boarding (Eaves Board of second class hard wood) clean sawn/plain 25mm thick and 225mm wide (V jointed to give 20mm laps) to replace old decayed boarding inclu cutting out old pieces and removing dismantling boarding complete all as specified and directed. Note:- (a) Quoted rate are deemed inclusive of two coat of synthetic enamel paint over and including one coat of primer as per manufactures instructions and scafolding work upto 14.00 meter.

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 20mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for 100 mm thick PCC type C-2, 1:3:6 using 40mm graded stone aggregate as in path/hardstanding complete as specofied and directed

Schedule of Credit