Military Engineer Services Tender

Material and labour for non skid ceramic tiles 7 to 8mm thick (square/ rectangular), area of each tile exc 0.11 sqm but not exc 0.16 sqm as in skirting over and including 10mm thick rendering in CM 1:4 set and jointed in neat cement slurry and pointed in white/coloured cement to match the existing surface make as a specified.

Material and labour for coloured Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 300X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match incl 10 mm thick rendering in CM 1:4 complete all as specified and directed.

Taking down chowkats or frames exc 1.50 sqm but n.exc 4.00 sqm with shutters (without taking off shutters from the frame), complete all as specified and directed.

Taking down chowkats or frames n' exc 1.50 sqm with shutters (without taking off shutters from the frame),complete all as specified and directed.

Taking down shuuter of any description exc 1.00 sqm but not exc 2.00 sqm each, complete all as specified and directed.

Refixing shutter in same opening after repairing complete area exc 1.00 Sqm but not exc 2.00 Sqm, complete all as specified and directed.

S&F pressed steel door frame 125x60 mm with one or more rebate incl necessary fixing lugs hings, lock strick etc, complete as specified and firected.

S&F pressed steel door frame 105x60 mm with one or more rebate incl necessary fixing lugs hings, lock strick etc, complete as specified and firected.

Material & Labour for PCC 1:2:4 type B0 (Using 12.5mm graded stone aggregate) as in filling of pressed steel frame, hold fast,coping etc.,complete all as specified and as directed.

Material & labour for 2nd class hard wood, plain, solid straight chowkats and frames worught, framed, rebated on the solid rounded of chamferred, put together with glue, pinned at joints supplied and fitted, complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube fixed as per manufacturer instructions complete all as specified and directed by Engr-in-Charge.

Supply and fixing 30 mm thick Flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides,complete all as specified and directed.

S&F plain colour Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing etc complete all as specified and directed.

M & L 35mm thick glazed and skelton shutters, open rebated and prepared to receive glass , gauge, etc (without sash bars) , edges of framing plain, chamfered of rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as spd in SSR Part-I, section 8, clause 8.24 (a) supplied and fitted to chowkhats , complete all as specified and directed.

S & F stainless steel wire cloth , 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

Supply and fix aluminium anodised (powder coated) Three track sliding window frame with shutters with ( 2 nos glazed and one wire gauzed shutter)including all necessary joining cleats, hold fast, rubber gasket, snap beading and locking arrangements fixed with screws to wall etc. complete and glazing with and including 4 mm thick glass to aluminium frame work using rubber gasket and including stainless steel wire cloth of 0.36 mm dia & average width of aperture 1.40mm with staple or suitable fillets wire mesh fitted with screws and washers etc including aluminium grill of thickness 5mm and opening not exceeding 75mmx75mm etc completee with the following section of frame and shutter (A) Sections for shutter (i) 'H' section 39 x 20 x 1.50 mm thick (ii) 'Interlock' section 39 x 20 x 1.50 mm thick (iii) 'Edge & Bottom' section 41 x 20 x 1.50 mm thick (B) Section for frame (i) Top & Sides 92 X 29.50X 1.50mm thick (ii) Bottom 92 X 29.70 X 1.50mm thick complete all as specified and directed .

Supply and fix aluminium anodised (powder coated) Ventilator frame with Shutter(bottom Half Portion Fixed and top half portion with louver) including all necessary joining cleats, hold fast, rubber gasket, snap beading and locking arrangements fixed with screws to wall etc. complete and glazing with and including 4 mm thick frosted glass to aluminium frame work and louver using rubber gasket and fixed with stainless steel wire cloth of 0.36 mm dia & average width of aperture 1.40mm outside vent with staple and suitable wall angle of size 25.4x25.40x1.1mm thick and fillets with screws and washers etc including Deco Grill of Model / Design No. DG 104 and 6.3mm thick etc (A) Section for frame 63.5 X 38.1X 1.40mm thick, complete all as specified and as directed.

Material & labour preparation of new wooden surfaces of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

S & F aluminium alloy handles size 150mm fabricated type anodised ,complete all as specified and directed.

S & F aluminium anodised barrel tower bolt 150mm size of extruded section and fixed, complete all as specified and directed.

S & F aluminium alloy handles size 100mm fabricated type anodised ,complete all as specified and directed.

S & F aluminium anodised barrel tower bolt 100mm size of extruded section and fixed, complete all as specified and directed.

S & F 300 mm long aliminium alloy ,anodised sliding door bolt with hasp and staples (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast alunimium alloy and fixed , complete all as specified and directed.

S & F 100 mm butt hinges medium weight cold rolled mild steel and fixed ,complete all as specified and directed.

Material & labour for flat iron mild steel for hold fast size conforming to Fe-410-0 or Fe-310-0, complete all as specified and directed.

S & F in repair tubular 20mm decorative curtain rod ,complete all as specified and directed.

S&F in repair decorative brackets for curtain rod in any size ,complete all as specified and directed.

Taking up or down steel tubing 15mm bore and connections including cleaning for refixing or removal to store ,complete all as specified and directed.

Taking up or down steel tubing 20mm bore and connections including cleaning for refixing or removal to store ,complete all as specified and directed.

S&F CPVC pipes 20 mm outer diameter of SDR 11 & plain CPVC SDR 11 and fittings as in walls, ceiling, floor, etc. complete all as specified.

S&F CPVC pipes 25 mm outer diameter of SDR 11 & plain CPVC SDR 11 and fittings as in walls, ceiling, floor, etc. complete all as specified.

S&F in repair 600mm x 450mm bevelled edge mirror of selected quality glass, moulded on 6mm thick commercial ply wood and fixed to wooden plugs with cromium plated brass screw and cup washers,complete all as specified and directed.

S&F in repair PVC valve less syphonic action flushing cistern type 9 to 10 ltrs capacity with inlet, ball valve, float and handle including bracket, white colour of approved make, complete all as specified and directed.

Supply and fixed in repairs of vitreous china squatting pan of Orissa pattern size 580 mmx440mm white with P or S tap front or back inlet and integral foot rest ( Excluding flushing cistern and flush pipe),complete all as specified and directed.

M&L for Green Marble 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble over 15mm thick screed bed/bedding layer in CM 1:4, complete all as specified and directed.

Material and labour for 15 mm thick rendering in cement mortar (1:6) on fair faces of brick surfaces finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, chajja, fins, facia etc upto 3 storey height mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified. Note :- (a) Supply only water proofing compound shall be measured and paid separately under relevant items. (b) Cost of scafolding upto 3 storied height of building for rendering is deemed to be included in quoted rate of mixed wiht WPC in this item. (c) Rendering will be done in two layers. 1st layer will be 10 mm thick and 2nd layer will be 5 mm thick. .

Supply only Liquid water proofing compound, complete all as specified and directed.

Material and labour for 5 mm thick rendering in cement mortar (1:3) on concrete surface as in ceiling/chajja finished even and smooth without using extra cement , complete all as specified and directed.

Material and labour for applying three coats of white wash on ceiling including preparation of new or previously untreated surfaces,complete all as specified and directed.

Taking down soil pipe/ rainwater pipes (any size or pattern ) including all fitings heads shoes bends swan -necks etc including cleaning or refixing or removal to store (measured over all fixed along the centre line over fitting and ( accessories), complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including scafolding etc ,complete all as specified and directed.

S&F for 110mm dia PVC bend etc with access door fixed with rubbr ring fixed to wall including scafolding all as specified and directed.

S&F for 110mm dia PVC (SWR) branch piece,single (single Y) equal or unequal with access door including scafolding all as specified and directed.

S&F for 110mm dia PVC (SWR) junction single,(Single T) equal or unequal with access door including scafolding all as specified and directed.

M&L for 100MM PVC (SWR) floor trap, plain with grating including jointing with solvent cement, including making good distrubd area/surfaces with cement concrete/cement mortar 1:2:4 etc including taking down old unserviceable Nahani/Floor trap.

S&F in repairs 15 dia fancy type chromium plated Bib tap cast copper alloy etc complete all as specified and as directed.

S&F in repairs of stop valve 15 mm dia CP fancy type, with long shank and cup (concealed type) cast copper alloy, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repairs of stop valve 15 mm dia CP fancy type, with long shank and cup cast copper alloy, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repairs 15 mm dia fancy type pillar tap cast copper alloy, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe & fixed.

S&F in repairs Shower Rose 125mm size Chromium plated with swivel joints, any size, including fixing to steel pipe or union all as specified.

S & F in repairs Brass chromium plated tubelar towel rail, 20mm dia, D type, 60,cm long between flanges all as specified.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth in brick walls etc complete.

M&L for preparation of new plastered surfaces and applying two coats of oil emulsion distemper (any colour/tint) over a coat of primer and 1 mm thick wall care putty (Birla/Asian) on wall surfaces including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M & L for preparation of old surface of wall and treating with two coats of oil emulsion distemper (any colour/tint) over a coat of primer including rubbing with emmery paper to make wall surface smooth and even complete all as directed and specified.

Material & Labour for Preparation of new plastered surface of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces,Complete all as specified and as directed.

Material & Labour for Preparation of old plastered surface of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces,Complete all as specified and as directed.

M&L for preparation of old plastered ceiling surfaces and applying two coat of white wash (any colour/tint) on ceiling surfaces, complete all as specified and directed.

Material and labour for preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint all as specified.

Demolition of cement concrete of any dsecription and in any position not otherwise specifically provided for etc complete.

M&L for sunken treatment of Toilet/Bathroom as in following steps: i) Top of RCC slab in sunken portion including peripheral beams shall be plastered with 15mm thick in cement mortar 1 : 3 using approved water proofing compound @ 3% by weight of cement finished even and smooth using extra cement, curved at the junctions. ii) Apply two coats of epoxy resin/polymer modified cementations coating like brush bond of FOSROK/SIKA/Pedilite or equivalent, both on floor & beams. iii) Sunken slabs to be given 1:20 slope outward 25mm GI pipe spout with 300 mm projection beyond outer surface of wall shall be provided. iv) Water tightness of sunken portion to be tested by ponding with water for 72 hours. In case of even a slight mark of seepage, the portion to be treated and ponding shall be carried out again to confirm the water tightness of sunken slab. Note : No cutting in roof slab/beam shall be allowed for passing of CI pipes & fittings.The stage of water proofing to sunken slab shall be passed by Eng-in-charge/GE.

M&L for PCC 1:5:10 Type E2 (using 40mm graded crushed stone aggregate) as in filling sunken floor complete all as specified and as directed by Engineer-in-charge. (upto 04 storey High of building)

M&L for 25mm thick PCC 1:2:4 Type B-1 ( using 20 mm graded crushed stone aggregate) as in sub base of floor complete all as specified and as directed by Engineer-in-charge.. (upto 04 storey High of building)

M&L for 75 mm thick cement concrete 1:3:6 type C1 using 20 mm graded stone aggregate as in plinth protection finished fair and even with using extra cement complete all as directed.

M & L for prelaminated particle board 18/19mm thick in repair as in cup board shutter and Shelf, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame works complete all as spd and dir.

Material and labour for taking down of existing roof treatment from roof and terrace, roughening surface of old concrete roof by picking, sweeping clean and washing down with water to remove dust, etc and applying roof treatment with the following steps and specifications:- a) Applying crack seal compound of same manufacture of waterproof to fill all cracks of observed on the roof. b) Applying cement slurry over concrete surfaces @3kg/sqm. c) Rendering 15mm thick in cement mortar (1:4) mixed with water proofing compound as per manufactures’ instruction(not less than 3% by weight of cement) on cleaned concrete surfaces of roof and finishing the surfaces fair and even including curing the plastered surfaces for 7 days by ponding of water over the roof, (leveling course). d) Applying evenly one coat of primer coating (diluted with water in the ratio specified by Manufacturers) (min @100-110Sq Ft per liter (diluted quantity)) on the cleaned plastered surfaces. The surface shall be left for air dry for minimum period of 2-3 Hrs. e) Applying evenly one coat of elastomeric water proof coat in one direction (as specified by Manufacturers)(min@ 0.9-1.0 sqm per ltrs) and allow to air dry for 4-6 hrs before applying second coat in other direction perpendicular to the first one (as specified by Manufacturers) (min @0.9-1.0 sqm per ltrs. The total thickness of two coats shall be 0.5 to 0.6 mm. f) The whole system shall be left for air cure for min Seven days (without any movement). Make : - Dr Fixit Newcoat Ezee or Berger Home Shield PU RoofKoat or Asian Paints Smartcare Damp Proof or as equivalent approved by GE. Note : - (i) The waterproofing shall be carried out in the last stage of execution to avoid any damages during the execution. (ii) Payment against this item shall not be allowed till completion of all the stages of work for any slab. (iii) The work shall be executed through Authorized well-trained applicators as per manufacturer’s instructions after obtaining written approval from the GE

Material and labour for complete/Partial removal of loose/ cracked concrete including cutting of reinforcement at Single/Double/Tripal storey if required from RCC roof projection, chajja, fins, facia etc and applying bonding agent as per manufacture instruction as per and making good with RCC (1:1.5:3) type A0 using 12.5 mm graded aggregate) in any slab and in any position finsihed the surface even and smooth with out using extra cement including necesary formwork and welding/binding of reinforcement if required, complete as directed by Engineer in charge. Note:- (1) reinforcement will be measured and paid seperately under respective items, (2) Quoted rate shall be inclusive of bondig agent fosroc nitobond EP ,Sika hibond, Pidilite 301 pidicrete URP. (3) The quoted rate shall be inclusive of Scaffolding if required.

M&L for Mild steel TMT bars 5 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S&F in repairs PVC connection pipe 15mm size with PTMT nuts of length 450mm long, complete all as specified and directed.

M&L for Providing and fixing false ceiling of designer tile ivory/white painted (high pressure steam cured ) of 4mm thick (as per IS: 14862) of size 595x595mm and any one of the design (cascade or electra) in true horizontal level. Suspended on inter locking metal grid of hot dipped galvanized steel section (galvanized @120gms both side inclusive and black painted groove on all T webs)consisting of main T runner with suitably spaced joints to get required length and 15x32mm made of 0.3mm thick sheet spaced at 1200mm c/c and cross T of size 15x32mm made of 0.3mm sheet 1200mm long spaecd between main T at 600mm c/c to form a grid of 1200x600mm and secondary cross T of length 600mm and size 15x32mm made of 0.3mm thick sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including required cutting/making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.Main T runners to be suspended from trusses/ceilings using suitable suspension arrangement as per manufacturers instructions/literature. GI adjustable wire of 4mm dia with galvanized butterfly level clips spaced at 1200mm c/c along main T bottom exposed width of 15mm of all T section of 4mm dia GI wire shall be pre-painted with with polyster paint and black painted groove at centre of size 4mm depth and 4.5mm width, including taking down old false ceiling board of any description alongwith rails and connecting items all complete at all heights as per direction of Engr-in-charge.

Dismantling AC/CGI/PPGI corrugated or semi corrugated sheets in wall cladding or roof coverings and hanger doors including ridges and make good for aluminium earthing strips after fixing of sheets, complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating PPGL based corrugated/Trapezoidal steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating PPGL based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, eave board, fixed with self tapping screws, complete all as specified and directed.

Demolition of RCC with concrete cutter machine of any description and in any position not otherwise specifically provided for including taking out and seperating old reinforcement and removal of debries to a distance not exc 50m as directed by Engineer in charge and making site clean complete all as specified and directed.

Dismantling water tanks exc 250 ltr capacity and n.exc 500ltr capacity and removing to store complete all as specified and directed.

Supply and fix of rotational moulded,multilayer HDPE water storage tank of 500 ltrs capacity( tripple layer wall construction , Cylindrical vertical with closed top) ISI marked hoisted and fixed in position all as specified in SSR Part I including 02 Nos 20 mm bore full threaded GI nipple of required size including ball valves 20 mm bore high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed (Minimum weight 20mm - 210gms and refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed

Supply & fix 20 mm bore gun metal, glove or gate valves ISI marked with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

Taking down and refixing of aluminium window after repairing including reapir/replacement of rubber gasket beading,roller,lock etc complete all as specified and as directed.

Schedule of Credit