Western Coalfields Limited Tender

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement:1½coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form work for: Columns, piers, abutments, pillars, posts and struts.

Brick work with non modular fly ash bricks conforming to IS" 12894, class designation 10 average compressive strength in foundation in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Carriage of earth work by mechanical means including loading and unloading etc. complete with 1.00 km lead.

Providing and fixing heavy duty inter locking concrete RUBBER MOULDGLOSSY PAVING BLOCKS of 60 millimeter thickness of having a strength of 400kilogram /sq.m of approved quality and shape on a bed of crushed sand of 25 to 30millimeter thick including striking joints and cleaning etc. complete .(using 100% crushed sand.

Providing and fixing informatory signboards in rectangular shape of size 1.20mx0.90m made out of 3mm Aluminum composite panel bonded with IRC Specified colour of retroreflective sheeting ofType IV High Intensity Micro-smatic Grade Sheeting(HIP) having pressure sensitive/heat activated adhesive, IRC Specified colour retroreflective cut out border & message shaving pressure sensitive adhesive having border & messages in IRC Specified colourbacK ground including M.S.angle ironframe of size35mmX35mmX3mm & two M.S.angle iron post of size 65mmX65mmX6mm,3.65m long, duly painted withflat oil paint having alternate black and white bands of 25cm width including G.I.fixtures etc; fixing the board sin M-20concrete block of size 60cmX60cmX75cm including transportation etc; complete. Aluminum composite panel Type IV High Intensity.

Finishing walls with Acrylic Smooth exterior paint of required shade . New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg/10 sqm)

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.Made of G.I. wire of dia 4 mm

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and fixing of Single air walker having product area 1065x785x1390 mm made up of 3 ''B' class MS pipe, prime stand duly bend, foundation center pipe . Pedal frame is made of 42mm OD MS pipe. Thehandle frame is made of 32mm OD MS pipe. Footrest frame support of dimension 250x100x2mm is welded for supporting the aluminum footrest. Aluminium footrest of size 300x150x5mm is used for supporting the foot 60mm dia seamless pipe bushes, permanent lubricanted ball bearins 6205zz/6205-2 rs. Foundation plate of 175mm dia and 10mm thicknes is welded at bottom. All welded joint are of good quality. High tensile steel with galvanished nut and bolts to be used the circlips to be used are of 25mm. Allen bolts are also used to tighten the closing cap, closing cap of HDPE/PPCP plastic is used including PU paint etc. complete as per direction of engineer incharge.

Providing and fixing of Single chest presser having product area 920x762x2134 mm made up of 4 ''B' class MS pipe, prime stand duly bend, foundation center pipe the handle frame is made of 42mm OD MS pipe. The remaining frame is made of 32mm OD MS pipe. seating frame support of dimension 250x150x5mm is welded for supporting the pedal seat. MS seat of size 300x300x5 mm is used for supporting the foot. 60mm dia seamless pipe bushes, permanent lubricanted ball bearins 6205zz/6205-2 rs. Foundation plate of 225mm dia and 10mm thicknes is welded at bottom. All welded joint are of good quality. High tensile steel with galvanished nut and bolts to be used the circlips to be used are of 25mm. Allen bolts are also used to tighten the closing cap, closing cap of HDPE/PPCP plastic is used including PU paint etc. complete as per direction of engineer incharge.

Providing and fixing of Single wheel shouder builder having product area 762x457x 1676 mm made up of 3 ''B' class MS pipe, prime stand duly bend, foundation center pipe the handle frame is made of 42mm OD MS pipe. The remaining frame is made of 32mm OD MS pipe,60mm dia seamless pipe bushes, permanent lubricanted ball bearins 6205zz/6205-2 rs. Foundation plate of 175mm dia and 10mm thicknes is welded at bottom. All welded joint are of good quality. High tensile steel with galvanished nut and bolts to be used the circlips to be used are of 25mm. Allen bolts are also used to tighten the closing cap, closing cap of HDPE/PPCP plastic is used including PU paint etc. complete as per direction of engineer incharge.

Providing and fixing of standing triple twister having product area 1460x1460x1370mm made up of 3 ''B' class MS pipe, prime stand duly bend, foundation center pipe the handle frame is made of 32mm OD MS pipe. The leg frame is made of 42mm OD MS pipe, round plate of 300mm dia and 10mm thickness is joined for standing and twisting, 60mm dia seamless pipe bushes, permanent lubricanted ball bearings 6205zz/6205-2 rs. Foundation plate of 175mm dia and 10mm thicknes is welded at bottom. All welded joint are of good quality. High tensile steel with galvanished nut and bolts to be used the circlips to be used are of 25mm. Allen bolts are also used to tighten the closing cap, closing cap of HDPE/PPCP plactic is used including PU paint etc. complete as per direction of engineer incharge.

Providing and fixing of Snake climber having product area3048x762x2134 mm made up of 2 " dia ''B' class MS pipe, prime stand duly bend, foundation center pipe the remaining frame of lader steps is made of 32mm OD MS pipe. All welded joint are of good quality. High tensile steel with galvanished nut and bolts to be used including PU paint etc. complete as per direction of engineer incharge.

Providing and fixing of Arm & paddle Bike having product area 1220x610x1067 mm made up of 3 ''B' class MS pipe, prime stand duly bend, foundation center pipe, the remaining frame is made of 42mm OD MS pipe. MS seat if size 380x300x5mm is used for seating arrangement. 60mm dia seamless pipe bushes, permanent lubricanted ball bearings 6205zz/6205-2 rs. Foundation plate of 200mm dia and 8mm thicknes is welded at bottom. All welded joint are of good quality. High tensile steel with galvanished nut and bolts to be used the circlips to be used are of 25mm. Allen bolts are also used to tighten the closing cap, closing cap of HDPE/PPCP plastic is used including PU paint etc. complete as per direction of engineer incharge.

Providing and fixing of Knee Chair having product area 690x 490x 1220mm made up of 3 " dia ''B' class MS pipe, prime stand duly bend,the leg and set frame is made of 42mm OD MS pipe. the handle frame is made of 32mm OD MS pipe permanent lubricanted ball bearings 6205zz/6205-2rs. foundation plate of 200mm dia and 10mm thickness is welded at bottom. All welded joint are of good quality. High tensile steel with galvanished nut and bolts to be used including PU paint etc. complete as per direction of engineer incharge.

Providing and fixing of parallel bar having product area 1828x685x1524 mm made up of 2 " dia ''B' class MS pipe, prime stand duly bend, foundation center plate the handle frame is made of 38mm OD MS pipe. All welded joint are of good quality. High tensile steel with galvanished nut and bolts to be used including PU paint etc. complete as per direction of engineer incharge.

Total impact of GST for the purpose of CTC