Military Engineer Services Tender

Supply and fixing Double wall Corrugated High Density Polymer Ethylene (HDPE) pipe of SIZE 50 mm diameter as per IS 14930 (Part-2):2001, Laid in trenches/floors and fixed on walls/poles, with and including neccessary fittings such as bends, sockets and other connected accessories etc., for laying of electric cables, complete all as specified and as directed. by EIC

All as per item No 4 above….. But for HDPE pipe size 90 mm diameter

Taking out LT XLPE/PVC insulated armoured cable alongwith all joints of any size from trenches wall/roof including taking out of brick layer and sand from trenches complete all as directed by EIC.

Supply, laying and testing 10 Sq mm 2 core LT XLPE insuated PVC bedded galvanised steel strip or wire armoured earthed electric power cable with aluminium conductor 1100 volts grade, heavy duty in trenches/along pole or wall complete all as specified and directed by Engineer-in-Charges. Note:- 1. Excavation and earth work, sand cushioning, brick pipes, clamps, and cable joint shall be measured and paid separetely under respective items :-

All as per item No 7 above….. But of size 16 Sq mm 2 core

All as per item No 7 above….. But of 10 Sq mm 4 core

All as per item No 7 above….. But of size 16 Sq mm 4 core

All as per item No 7 above….. But of 25 Sq mm 4 core

All as per item No 7 above….. But of 35 Sq mm 3.5 core

All as per item No 7 above….. But of 50 Sq mm 3.5 core

All as per item No 7 above….. But of 70 Sq mm 3.5 core

Supply & laying in repair 40mm bore galvanized steel tubing "light grade" with all fittings in trenches/ under roads/ along pole/ wall for cable protection all as specified & directed by Engr-in-Chrage. .

All as per item No 15 above….. But of size50 mm bore

Road cutting for UG cable under road/railway crossing, pavement, hardstanding by mannually means, protection GI pipe for cable of required dai and making it good to match with the adjoining surface/structure for after cable passing complete all as specified and directed. by EIC Note : GI pipe and PCC will be measured and paid against respective items.

Material and Labour for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation of pole upto ground level complete all as directed .

PCC (1:3:6) type C-1 using 20 mm graded stone aggregate as in coping/plinth block including necessary form work all as directed by Engr-in-Chrage.

S&F for Ampere meter square type 96 x 96 mm 0-400 Amps with CT and selector switch (Digital type)

S&F for Voltmeter square type 96 x 96 mm 0-500 V with inbuilt selector switch - ( Digital type)

S&F for Indicator lamp neon/LED type (set of three ) complete all as specified ad directed. by Engr-in-Chrage

S& F for Panel Wiring with suitable size PVC insulated PVC sheathed 1100 volts grade FRLSH type with copper conductor multistranded cable not less than 1.5 sqmm with lugs on both ends of cable. complete all as specified ad directed. by Engr-in-Chrage

M& L for taking out LT feeder panel front and back type opening replace old clamps and fix new hinges by drilling or belding as per condition , replaced burnt out lugs and insulation , proper, insulation taping to XLPE cable and painting inner and outer side , top and bottam, including cleaning of grass around, from the panel till 2mtr and from road to panel for easy operation complete all as specified and drirected by Engr-In-Charge

M& L for taking out LT feeder panel all cables from loops, for fixing GI Pipe for cable protection and making new foundation in place of broken foundation with PCC 1:4:8 in 40 mm graded stone aggregate and re-fixing all cables with proper lugs after inserting through GI pipe complete. Note :; PCC shall be measured and paid in the respective items.

M&L for Preparation of old painted surfaces of steel tubular poles 9/11 Mtr long including cross arms protection pipe and painting one coat of aluminium paint e ground level to top of pole and cross arms and protection pipe paint including writing poles numbers in white letter on black ground complete all as specified and directed by Engr-in-Charge.

S and F in repair loop in / loop out box of internal size 350 x 250 x 150mm made out of FRP (Hot moulded type) with weather proof canopy and locking screws alongwith 5/6 Amps MCB-01 No, 15 Amps rated 3 pole connector - 01 Nos, neutral link mounted and Din rail suitable size for mounting MCB/Connector complete in the box, duly fixed to steel tubular pole using 25 x 3mm FI clamp with suitable gland and lugs for connecting cable including taking down old one complete all as specified and as directed.

Material and labour in replacement/repair for earthing complete with galvanized steel earth plate electrode 600mm X 600mm X 6mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level (with top edge of earth plate not less than 1.5 meter below ground level) connected to GI strip 32mm X 6mm main earthing lead by means of galvanized bolts, nuts and washers all as shown in electrical plate no 5 of MES Schedule Part-I (2009) connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt alround earth plate, PCC (1:3:6) type C-1 (using 20mm graded black trap/granite/Basalt stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, pre cast RCC (1:2:4) type B-1 (using 20mm graded stone aggregate) 50mm thick cover reinforced with 8mm dia TMT bars @ 100mm c/c both way with 12mm dia round bar handle, GI medium grade watering pipe 20 mm bore GI medium grade earth lead protection pipe, complete all as specified and directed. Note :- Earth strip 32x6 mm and protection pipe 40 mm dia up to 7.5 mtr shall be included in quoted rate.

Supply and fixing in replacement of SCR controlled cum boost single phase 30 volt 40 Amp Battery charger of make APEX and DC distribution board in commoncubical. The charger is suitable for 230 Volt +/- 10% single phase AC input and DC output for 24 volt -100 AH Battery Bank and supply load. DC Distribution Board : Incomer : 63 Amp MCB DP-01 No Outgoing : 16/20 Amp MCB DP-01 No supply of lead Acid SMF VRLA Battery Bjank of 30 Volt 100 AH consisting of 15 Nos cells of 02 Volts 100 AH capacity each complete with inter cell connector SS Nut, Bolts and washers MS powder coated stand in factory charged condition complete all as specified ad directed. by Engr-in-Chrage

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections twin core cable of size 10 Sqmm flat complete all as specified ad directed. by Engr-in-Chrage

All as per item Sr No 30 above but of size 6 Sqmm.complete all as specified ad directed. by Engr-in-Chrage

Material and labour for coarse aggregate filling using stone gravels, rounded, of size n exc. 43 mm suitable to site, in the area covered by four pole structures complete all as specified and directed.

Supply install, testing and commissioning Out door, in replacement of LT Distribution Panel Feeder Pillar (CPRI approved) Cubicle type,IP-56,outdoor type confirming to IS: 61439 Part I & II factory fabricated made out of outer cover with 3 mm thick CRCA sheet & inner cover with 2mm thick CRCA sheet of suitable size to accommodate all accessories / fittings, compartmentalized in costruction to accommodate the incoming MCCB and TPN bus bars and outgoing MCCBs feeders. The TPN busbars shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on DMC/epoxy insulator at an interval of not more than 500 mm through out the length of the TPN bus bar. The incoming as well as outgoing MCCBs shall have extension links of current carrying cap not less than 1.5 times the rated capacity of individual feeders. The extension links shall be supported on DMC/Epoxy insulators having provision for termination of incoming and outgoing cables. The cubicle shall have a bottom and four legs (400mm long) of size 50x 50x6 mm, The panel shall be painting with powder coated finish with RAL 7032 SIEMENS GRAY STRUCTURE after seven tank phosphating treatment, front & back opening type, and fixing 2 Nos.danger notice plate with letter, figures and conventional skull bones in signal red colour and fixed front & back door to LT panel with voltage and danger indicated in Hindi and English, with double door shutter and shall have louvers and airvent gasket for natural flow of air, Neoprene adhesive type gasket shall be used to make panel vermin proof and comprising of following all as specified and directed by EIC. (a) incoming (i) Aluminium busbar, 4 Pole, 300 Amps (ii) MCCB 4P, 160A, 36 KA, with thermal magnetic: O/L & S/C protection , ICS= 100% ICU = 01 No. (iii) Ammeter Digital type, CT operated 0-630A range, (with selector switch and CT) - 01 Set (iv) Volt Meter Digital type 0-500 V range, (With selector switch) - 01 No. (v ) Indicating Lamp LED type 240 V 50 HZ AC supply set of three colour (RYB)-01 set. (b) Outgoing :- (i) MCCB 4P, 63A, 25 KA, with thermal magnetic: O/L & S/C protection , ICS= 100% ICU = 01 Nos. (ii) MCB TPN, 32A, 10 KA, with thermal magnetic: O/L & S/C protection , ICS= 100% ICU = 04 Nos.