Military Engineer Services Tender

Taking down chowkhats or frame not exc 1.5 sq. m but n exc 4 sq m each with shutters (without taking off shutters from the frames complete all as specified and directed.

M&L for double charged vitrified coloured tiles light shade 10 mm thick (square/ rectangular) polished, area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm in floors etc, set and jointed in neat cement slurry and pointed with colour cement, laid over and including 15mm thick bedding layer in cement mortar 1:6, complete all as specified and directed.

M&L for coloured Glazed ceramic tiles as in vertical surface of Size 350 x 250 x 7mm / 450 x 350 x 7 mm set and jointed in neat cement slurry laid over and including 10 mm thick rendering in C M (1:4), complete all as specified and directed.

M&L 20 (+ -2mm) thick Granite (of jet black) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking plateforms and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite complete all as specified. Exposed edges to make half round incl 20 mm thick bedding layer in CM (1:4) complete all as specified and directed

M&L Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete and incl 20mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed

M&L precast cement concrete 1:3:6 type C-1 (using 20mm graded aggregate) block masonry with solid blocks exc10 cm thick in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for 15 mm thick cement plaster on brick or concrete surface in cement mortar1:6 included finishing surface even and smooth without using extra cement on walls etc complete all as specified and directed.

M&L for 15 mm thick cement plaster on brick or concrete surface in cement mortar 1:4 included finishing surface even and smooth without using extra cement on walls etc complete all as specified and directed

Taking down 15 mm bore mild steel tubing of medium grade and connections incl cleaning for refixing or removal from site complete all as specified and as directed

All as per above Ser item No 12 but for 20 mm bore

S&F 15 mm bore mild steel water tubing medium grade galvanized with all fittings and fixture fixed to walls ceiling or laid in floors complete all as specified and as directed

All as per above Ser item No 14 but for 20 mm bore

M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth etc. complete all as specified and directed.

Supply and Fixing in repairs, wash hand basins vitreous china flat back 630mmx450mm size white, first quality, with and including chromium plated waste grating 32mm size, PVC waste pipe 25mm bore heavy duty China and plug and porcelain stopper, brackets of Mild Steel angle iron (35mmx35mmx5mm) of suitable size including two coat of synthetic enamel paint over a coat of primer over angle iron brackets complete to walls all specified and as directed

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, screwed for iron pipe of bore 15 mm fixed complete all as specified and directed.

S&F in repairs of fancy type concealed stop cock cast copper alloy screws down high pressure screw both ends for iron pipe or of bore 15 mm fixed complete all as specified and directed.

S&F in repairs elegent mirror PVC cabinet coloured with towel rail of size 422 x 622 mm complete all as specified and directed.

Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions false ceiling including sunk or raised moulding pattern approved by GE fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish including necessary supporting hanger with 4.0 mm dia GI wire and 'J' bolts washer nuts for securing frame work to Gl frame work for (605 mm x 605 mm) seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre incl thin layer of putty with gypsum binder, sanding the sufrace till smooth surface is obtained and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed

M&L First class soft wood Moulding area of exc 13 sqcm but n exc 25 sqcm as in cornices, picture rails and the like fixed with screws complete all as specified and directed

M& L for complete removal of existing treatment of old wall surfaces and applying 2mm thick plaster of paris putty over prepared plastered surface to receive the surface even and smooth and applying two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre of approved manufacturer of required shade and colour complete over a coat of wall primer as per manufacturer's specification complete all as specified and as directed

S&F aluminium powder coated three track sliding window with mosquito net two track for glass leaf sliding and one track for mesh leaf sliding outer frame weighing 0.699 Kg/m, 75x26 mm size equvalent Jindal model 20671, shutter plain of size 37.5x15mm weighing 0.366 Kg/m, Section No 20690 Jindal), with powder coating of min thickness 50 micron with one or more rebates, sliding type without sash bars, 5mm thickness double tampered clear glass, rubber packing, snap beading screws, with horizontal sliding type with stainless steel mesh, frame, powder coated aluminium grill type AL 925 or equvalent grill, cutting in suitable size and fitting with screws and suitable beedings to aluminum window frame complete etc.complete all as specified and directed.

S&F anodised aluminium powder coated frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F anodised aluminium powder coated door shutter, aluminium section wt 0.55 Kg/m including neccesary joining cleats, glazing clips, rubber neoprene packing, handle 2 Nos in each door, hinges, anodised aluminium snap beading screw etc, complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings complete all as specified and directed.

S&F 5.50mm thick selected quality plain or grounded or frosted glass in squares in exc 0.5 sq.m in each pane including solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers fixing with rubber beading or PVC gasket etc complete all as specified and directed

S&F Door closer hydraulically regulated, designation No. 2, universal type, aluminium (Die cast) body suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed etc. complete all as specified and directed.

S & F Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for preparing new or previously untreated surface cleaning with scrapers steel surfaces exc.10cm width or girth and applying one coat of synthetic enamel paint, including grills, gate complete all as specified and directed.

S&F MS powder coated 20 mm dia curtain rod including wooden polished brackets and wooden polished end knobs fixed with plugs & screws, complete all as specified and directed.

Taking down PVC SWR (any size or pattern) including all fittings, heads, shoes, bends, swan-necks, etc including cleaning or refixing or removal to Store etc complete all as specified and directed.

M&L for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or floor complete all as specified and directed.

S&F for 75mm bore dia PVC (SWR) bends with access door complete all as specified and directed.

S&F PVC connection 75cm long 15mm dia, with 2 Nos CP brass check nuts complete all as specified and directed.

M&L for second class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed

S&F 35 mm thick factory made plain framed, panelled shutters with 2nd class hard wood rails and panel of 9mm BWP commercial ply 12mm thick veneered particle board with commercial veneers on both faces. The size of rail or style shall be as per IS 1003 Part-I Kiln seasoned and chemically pressure treated complete all as specified and directed

S&F 100mm butt hinges cold rolled mild steel medium weight and fixed complete all as specified and directed.

S&F 150mm Aluminium handles, cast type, anodised complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections all as specified and directed

S&F Aluminium anodised barrel tower bolts of extruded section 100mm long complete all as specified and directed.

M&L machine cut superior quality Kota stone slab flooring 20-25 mm thick over cement screed, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete match including bulnosed to edges complete and incl 20 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed

M&L for broken stone Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L 100mm thick cement concrete type D2, 1:4:8 (Using 40mm size graded granite stone aggregate) as in sub base including use of necessary form work complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over one coat of alkali registant priming paint etc complete all as specified and directed.

M&L preparation of newly plastered surfaces of wall and applying two coats of cement base paint white or tinted over a coat of primer including scaffolding arrangement, trestles, ladders etc complete all as specified and directed.

M&L for making holes by core cutting machine on stone/concrete / brick walls. Dia of hole not exc. 20mm to 40mm and thickness of wall 50cm to 70cm for entry of suction and discharge pipes and making good distarbed surfaces with cement mortar and finally finished with plaster of parise and painted the distrubed surfaces with existing type of paint and tint complete all as specified and directed.

S&F 15 mm OD x 0.9 mm thick Copper Pipe for distribution of medical gases i. e. oxigen, Nitrogen, Oxide, Air and vaccume as per suitable colour code including SS saddles clamps of suitable size, fitting like Tee, Bends, Reducers etc. and all connected items & necessary welding works for fixing of copper pipe as per BS EN 13348:2001 standard alongwith third party inspection certificate from Lloyds' complete all as specified and as directed

S&F Pipeline & all required necessary Accessories BS / DIN Type Gas Outlets For Wall / BHP / Pendants - Front Loading for following items: (a) S&F Oxygen Gas Outlet complete all as specified and as directed.

(b)S&F Medical Air Gas Outlet - 4 Bar complete all as specified and as directed.

(c) S&F Vacuum Gas Outlet complete all as specified and as directed.

S&F 15mm Isoaltion Ball Valves with Brass adapters for area / regional isolation complete all as specified and as directed

Bed Head Panels S & F Metal Enclosures with Powder coating for Type A For ICU, OT, post and pre-oprative room and Accidential Trauma care beds - Provision for - 4 Gas Points, 4 electrical sockets, 1 nurse call socket, 1 RJ45 socket complete all as specified and as directed.

Gas Accessories S&F BPS Flow Meter With Humidifier bottle For Oxygen complete all as specified and as directed.

S&F Ward Suction Unit 600 ml Jar with regulator for Vaccum complete all as specified and as directed.

S&F Hose connection Probes For Oxygen, Nitrous, Air-4 & Vacum For BPC, Ward vacum Unit, Ventilators & Anesthesia W/s complete all as specified and as directed.

S&F Low Pressure Tubing for Ward / ICU suction units complete all as specified and as directed.

S&F Hanging Support- Threaded rod, Fastner, C-channel patti & Saddle / Mansoon Ring with fastners & threaded Rods complete all as specified and as directed.

Removing & Refixing of MGPS Accessories (i) Bed Head Panel - Alluminium Extrusion With separate section for electrical & gas point. (ii) Removing medical gas pipelines whereever necessary as per requirement of site taking all as saftey precautions.

Taking down exiting copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc as directed

M&L for concealed point wiring in and including new PVC conduit medium grade with the help of multi-stranded unsheathed FRLSH copper cable 1.5 sqmm 650/1100V conforming IS:3419 -1988 adhereing to colour code including earth wire of the size 1.5 Sqmm green colored with modular steel or cast iron terminal boxes and modular cover plates as required at site including making good the distrubed surfaces and matching it with existing surface for the following :- (a) One light/Fan point controlled by one way switch 6 Amps 240 volts

(b) One 3 pin socket outlet, 5/6 Amps on the same board with other switches

(c) One 3 pin socket outlet, 5/6 Amps, independent

(d) M&L point wiring for one 3 pin socket outlet 15 Amp Independent with 4 sq mm copper conductor FRLSH (multistrand) PVC insulated ISI marked unseathed cable in and including PVC conduit not less than 25 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 4 sq mm copper conductor as earth wire to common earth dolly all as specified

(e) One bell/ buzzer point controlled by one push button on independent board with cables 1.5 sq.mm size

S&F modular switch 1 way 10 A 1 module complete all as specified and directed.

S&F Modular socket 6 A 2/3 Pin 2 module complete all as specified and directed.

S&F modular switch 1 way 16 A 1 module complete all as specified and directed.

S&F Modular socket 6 A/16A 2/3 Pin 2 module complete all as specified and directed

S&F modular fan regulator, 2 module, suitable for ceiling fan of 1200/1400mm sweep complete all as specified and directed

M&L in replacement of modular bell push flush type 5Amps single polecomplete all as specified and directed

S&F electric bell Ding Dong type AC, 230 volts single phase complete all as specified.

S&F in replacement for ceiling rose, 3 terminals / PVC / Polycarbonate, isolated body complete all as specified and directed

S & F RJ-11 telephone socket with transparent shutter 2 module alongwith flush metal box 2 module and front cover plate 2 module complete all as specified and directed

S & F for LAN RJ-45 Jack With Cat 6 socket UTP Cat with transparent shutter 1 module alongwith flush metal box 1 module and front cover plate 1 module complete all as specified and directed

S&F in repairs Telephone cables for indoor applications up to 4 pair pvc insulated copper conductor wire including heavy duty non metalic PVC conduit, ISI marked, not less than 20 mm dia of thickness 1.8 mm concealed in wall, roof, etc, with all connected fittings from tag block to telephone outlet complete as required at site including making good surfaces and matching with the existing surface complete all as specified and directed

S&F in repairs Cat 6-4 pair, 23 AWG, UTP Cable, 305m waith cross member pair spearator including heavy duty non metalic PVC conduit, ISI marked, not less than 20 mm dia of thickness 1.8 mm concealed in wall, roof, etc, with all connected fittings complete as required at site including making good surfaces and matching with the existing surface all as specified and directed. Make -Havells WHLJTTERCAT6 or equivalent make as mentioned at makes list in PS

S&F in replacement of 20 watt, 230V surface and wall mounted warm white LED Smart batten, Smart extruded aluminium housing with higher efficaay. Microwave sensor to save more energy. Reduces the light intensity by 70% during non occupancy including connecting up with twin core twisted flexible copper condctor cable from ceiling rose all as specified and directed . Make- Bajaj BCLAB 20W LED PS or equivalent make as mentioned at makes list in PS

S&F in replacement of 12 watt, 230V surface and wall mounted warm white LED Mirror Light including connecting up with twin core twisted flexible copper condctor cable from ceiling rose all as specified and directed . Make- Luker LIMR 12 or equivalent make as mentioned at makes list in PS

S&F in repalcement recess type LED ceiling lights 12 W LED with ceiling cut out of Ø 95 mm Environmental friendly, energy saving, recess mounted downlighter with separate replaceable electronic driver including connecting with twin core wire, including cutting the existing false ceiling dia to the required size and also matching to the adjacent false ceiling surfaces carefully complete all as specified and directed . Make: Luker cat part no. LDR12MTL or equivalent make as mentioned at makes list in PS

S&F in replacement PR Motion Sensor for light fittings including connecting up with twin core twisted flexible copper cable to switch and fitting complete all as specified and directed

S&F of Plastic ventilation Energy Saving Exhaust Fan with BLDC Motor fan of 150 mm sweep inclduing replacing the plywood as per the site requirement all as specified and directed Note:- Old U/s fan dismantled from site and deposited at MES store Yard.

S&F in replacement of GI pipe ceiling fan down rod of 15 mm dia up to 1 mtr long for ceiling fan made out of 15 mm dia GI heavy grade pipe fixed on ceiling using suitable clamp including necessary new nut, bolt and washer complete all as specified and directed.

Supply and fixing ceiling fan complete with blades, down rods and other accessories, 230 V, 1200 mm sweep with Minimum air delivery of 210 CMM BEE Five star rated with brushless direct current motor (BLDC), white/Ivory in colour all as specified and directed . Note:- Old U/s fan dismantled from site and deposited at MES store Yard.

M&L for Cutting chases for concealed conduit wiring, pinning in and making good to surface where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., cutting not exc 10 cm girth including 3 mm thick wall care putty on wall, making surface matching to adjacent surface all as specified and directed.

Taking down exiting copper/aluminium sub main wiring complete for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc as directed

M&L for concealed sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 4 Sqmm, 1100 Volts grade in and including PVC conduit medium grade with all fitting & other accessories and copper cable 4 sqmm continuous earth wire complete all as specified and directed . Note: Two runs of 04 Sqmm cable with 01run of 4 Sqmm earth wire along with PVC conduit medium grade shall be measured as one RM

M&L for concealed sub main wiring with Two single core PVC insulated FRLS cables with stranded copper conductors 6 Sqmm, 1100 Volts grade in and including PVC conduit medium grade with all fitting & other accessories and copper cable 4 sqmm continuous earth wire complete all as specified and directed . Note: Two runs of 06 Sqmm cable with 01 run of 4 Sqmm earth wire along with PVC conduit medium grade shall be measured as one RM

M&L for concealed sub main wiring with Four single core PVC insulated FRLS cables with stranded copper conductors 10 Sqmm, 1100 Volts grade in and including PVC conduit medium grade with all fitting & other accessories and 2 run of copper cable 10 sqmm continuous earth wire complete all as specified and directed . Note: Four runs of 10 Sqmm cable with 02 run of 10 Sqmm earth wire along with PVC conduit medium grade shall be measured as one RM

S&F in replacement sheet metal enclosures double pole MCB 20 Amps with a two pin and earth plug and socket complete with all accessaries etc all as specified and directed by Engr-in-charge. Make: Legrand Cat part: 5078 10 or equivalent make as mentioned at makes list in PS

S&F in replacement MCB DB 8 way SPN Double door sheet metal enclosure factory made suitable for MCB DB's 240 volts, concealed in wall complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site complete all as specified and directed . Note - MCBs will be measured & paid separately under respective item of Sch A, if required to be replaced.

S&F MCB SP 6 to 32 Amps 240V,10 KA breaking capacity, B curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing complete all as specified and directed

S&F in replacement of C Curve MCB SPN 40 Amps working on 240 volts, 50 HZ,10 KA all as specified and directed .

S&F MCCB with rating of 125 Amps, 415 Volts 3 pole with 16 kA breaking capacity, thermal magnetic asdjustable of overload & short circuit release as per IS-13947 & IEC 60947-2 & the service short circuit breaking capacity (Ics) should be equal to ultimate breaking capcity (Icu). MCCB should be with suitable spreaders and phase barriers for each terminals complete all as specified and directed

Supply and fixing factory made epoxy powder coated Distribution Board TP & N 4 way double door (VTPN MCCB DB) MCCB as In comer, with metal door (IP-43 protection) fabricated from CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockout flush to wall and making good disturbed surface and touch up with the same finishes complete all as specified and directed Note:MCBs/ MCCBs will be measured and paid seperately under respective Sch A item in the schedule

S&F in repairs SHEET METAL ENCLOSURES TPN 4 way single door MCB/MCCB as In comer complete all as specified and directed Note : MCBs/ MCCBs will be measured and paid seperately under respective Sch A item in the schedule

Earthing complete with galvanised iron earth plate electrode 600 x 600 x 6mm as earthing lead buried directly in ground vertically to depth not less than 2.25 mtr below GL with the top edge of the plate not less than 1.5 mtr from GL, connected to GI earth lead of 4.0mm dia, by means of bolts & nuts, to GI and connected to earthing test point all as shown in elecrical plate No. 3 of SSR Part-I of 2009* specified or indicated and testing on completion including excavation / earth work in any type of starta, PCC (1:3:6) type C1 earthing chamber pre cast slab 50 mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric (XPM) weight not less than 4 KG/sqm cast iron frame, funnel with wire mesh GI watering pipe of 20 mm bore medium grade and lugs with and including GI earth wire 4 mm dia with GI protection pipe of 15 mm medium grade 7.5 meter long etc complete tested on completion all as specified and directed. Note: 1. Rate quoted shall deemed to include cost of excavation in any type of strata, RFR and removal upto 50metre, PCC pit, funnel and RCC cover plate. 2. GI wire above 7.5m will be measured and paid seperately.

Supply, installation, testing and commissioning of servo controlled for automatic operation Voltage stabilizer of capacity 30 KVA, 3 phase, 415 volts, 50 HZ 4 wire oil cooled balanced load type AC supply with input 260 - 480 volts and output votage of 400 to 440 volts + 2.5% balance supply with accuracy speed of 8 volt per second copper wound with protection switches, meters,control fuse etc and including first fill of transformer oil of BDV value not less than 50 KA complete all as specified and directed . Make : Vinitec/Blue Line/Paradise/Logistic. Note : (a) Under/Over voltage cut off single phase preventer, servo bypass switch, time delay over load and short circuit trip facility, spike and surge supressor Reverse Phase protection ammeter wtih CTs and selector switch shall be supplied within overall cost quoted.

Supply and fix UPS for 30 min back up LF 3P/3P 360 Online UPS with inbuild isolation transformer IGBT based PWM technology high efficiency design of capacity 30 KVA with 30 numbers of 65 AH 12V SMF Battery and including MS battery rack and interlinking cable and installation all as specified and directed

Supply & Laying, jointing & testing of UG LT cables XLPE insulated, PVC sheathed aluminium conductor multi stranded armoured heavy duty 1100 Volt grade cross sectional area 16 sqmm 4 core laid in trenches/ ducts/ along poles/through pipe under road etc with new aluminium lugs of cable size including removal of existing all as specified and directed

S&F GI tubing 'light grade' 50 mm dia ISI marked with all fittings laid in trenches and fixed on pole by flat iron clamps, nut, bolt, washer of suitable size complete all as specified and directed

Supply, Installation, Testing & Commissioning of Wire Mesh galvanized cable trays with a 50 mm x 200 mm mesh configuration along with all necessary accessories. Wire Mesh Cable Tray galvanized after manufacture in accordanceTrays should comply Standard EN ISO 14 61: at least 550 h of SST. The electrical resistance of the joints must not exceed 50 mΩ and must be tested in accordance with the procedure described in the standard IEC 61537. Assemblies with specific fire-resistant properties must have an E30-E90 certificate issued by an approved laboratory in accordance with the tests described in the standard DIN 4102-12. The wire cable tray short-circuit resistance must be tested by an independent laboratory. For the purpose of assembling the various wire cable tray, only fast coupling systems or screw-based (CE25/CE30) systems must be used. These must be designed, mechanically tested and supplied by the wire cable tray manufacturer.The electrical resistance of the joints must not exceed 50 mΩ and must be tested in accordance with the procedure described in the standard IEC 61537.Rod dia must be from 3.9mm to 5.9mm for different sizes. The loading capacities of the brackets and the hanger torques must be tested in accordance with the standard IEC 61537. The tray along with the accessories should not contain any metallic burrs to avoid damaging of cable insulation.CF54/200GC CABLE TRAY GC,CONSOLE CSN 200 GC,KITASSTRDC COUPLING KIT complete all as specified and directed Make:- Legrand or equivalent

Supply and installation of Chemical Earthing Electrode 25mm Pure Copper Solid Earthing Electrode 3mtr In length Copper Terminal of 100X50X5 mm BFC Compound (Back Fill Compound) The BFC is carbide based having very high electrical conductivity. BFC having high moisture retaining capacity. BFC is hygroscopic, nonmagnetic and non-corrosive in nature and is ROHS Compliant The Earthing electrode will be placed in the ground after a bore is drilled to the depth of 3.5m The Bore drilling will be done with the help of Pneumatic boring machine.50KG BFC will be placed in the bore to cover the Earthing rod from all sides. BFC will be poured in Slurry form in properly mixed condition Earth Pit Cover Square 300X300X240mm to be provided to cover the Earth Pit. Only supply of pit cover. The Earth pit Cover shall be made of Reinforced FRP and should be capable of carrying the weight of 5 tons complete all as specified and directed

S&F Earth continuity strip or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any with proper insulators other indicated situation for loop earthing etc. as required 20x3mm copper strip over green color insulation cover connects the equipment or electrical system to the earth pit complete all as specified and directed

Supply and install hi wall split type AC units indoor / outdoor complete with cordless remote control unit and with in built air ioniser invertor type compressor, 100% copper tubing of indoor & Outdoor cooling & condenser unit respectively with CFC free gas for better indoor air quality with 5 star rating and EER 3.2 of capacity 1.5 TR single phase including cabling work, insulation between indoor unit to outdoor unit and provision of MS brackets for resting of outdoor units (where reqd) or making resting platform of outdoor unit by brick works complete all as specified and directed. Make : Carrier/Daikin/Hitachi/Blue Star

S&F voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 240 V with output voltage stabilized at 230 V with accuracy of + 2.5% and of capacity 5 KVA complete all as specified and directed.. Make : V-Guard / Vinitec / Microtek.

M&L for PVC pipe 20 mm dia heavy duty with all fittings and fixing accessories such as coupler, lock nut, saddle, pipe hook and laid on floor (for wash out line) complete all specified and directed.

M&L for making holes by core cutting machine on stone / concrete / brick walls. Dia of hole not exc 50mm and thickness of wall 50 cm to 70 cm for entry of suction and discharge pipes of AC and making good disturbed surfaces with cement mortered and finally finished with plaster of paris and painted the distrubed surfaces with existing type of paint and tint complete all as specified and directed.

M & L excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, laying of cables etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed.

M & L excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/hard rock complete all as specified and directed.

M & L Cement concrete 1:4:8 type D2 using 40mm size graded aggregate in as foundations, filling and mass, concrete complete all as specified and directed.

M&L Stone Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:4 complete all as specified and directed.

M&L RCC M30 (using 20 mm size graded stone aggregates) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L RCC M30 (using 20 mm size graded stone aggregates) Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels, balustrade, and the like complete all as specified and directed.

MS TMT bars 10mm dia and over cut to length, bent to shape required, including cranking bending spirally binding with and including mild steel wire annealed not less than 0.9mm dia complete all as specified and directed.

M&L Formwork in Rough finished concret to faces of to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping complete all as specified and directed.

M&L Formwork in Rough finished concrete faces of of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and directed.

M & L Boulder pitching, laid dry, hand packed tightly extra over hammer dressed facings, with maximum depression on face from straight edge held against the dressed surfac and grouted with cement and sand mortar 1:6 complete all as specified and directed.

M&L Flush pointing to squared rubble masonry, coursed or uncoursed or brought upto course in CM (1:4) etc.complete all as specified and directed

M & L for applying two coat of cement base paint on wall including preparation of surfaces with alkali resistant priming paint complete all as specified and directed.

M & L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M & L surface excavation n. exc 30cm deep and averaging 15cm deep and getting out Soft/loose soil complete all as specified and directed.

M&L for 150 mm thick PCC 1:2:4 type B1 (using 20mm size graded stone aggregates) as in floor including finishing cement concrete even and smooth without using extra cement complete all as specified and directed.

M&L 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall or laid in floors, as in weep hole complete all as specified and directed.

M & L Spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified and directed.

M & L Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade A (sika,Choksey or Approved make) complete all as specified and directed.

M& L PCC 1:2:4 type B2 (using 40mm size graded stone aggregates) as in foundations, filling and mass concrete and energy dissipator complete all as specified and directed.

M&L PCC 1:2:4 type B0 (using 12.5 mm size graded stone aggregate) as in plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

Removal of excavated material exc 1.50 Km. & n exc 5 km & depositing out side of MOD Land complete all as specified and directed.

M & L Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed. .

M&L for 60 mm thick glossy finished cement concrete coloured interlocking pavers, pattern as approved, as in floors or pavements, laid on 30 mm thick stone dust cusioning, laid dry to the profile as directed incl filetting to the edges in Cement concrete (1:2:4), all manufacturer's instruction complete all as directed

Supply and Laying in replacement including testing and commissioning LT UG Power cable, XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with multi-stranded aluminium conductor including termination with LT Panel/Feeder Pillar with galvanised or Cadmium plated high tensile nuts, bolts and washers etc including Sheddling /clamping on any type of wall with suitable size of GI Clamps, nuts, bolts & washers etc of size 3.5 Core 50 Sqmm including removal of existing complete all as specified and directed.

All as per item No.134 above but 35 Sqmm 3.5 core

Removing excavated material a distance n. exc 50 m & depositing where directed at a level n. exc 1.5 m above the starting point complete all as specified and directed. .

Supply and laying 63 x 50 mm outer & inner dia, double walled corrugated (DWC) HDPE duct pipe confirming to IS-16205 Pt-24 with antirodent and non flame propogating properties of approved colour complete with fittings i.e.coupler,Tee, elbow clamp for cable protection of size 50 to 35 Sqmm 3.5 core complete all as specified and directed . .

Supply and laying 40 x 32 mm outer & inner dia, double walled corrugated (DWC) HDPE duct pipe confirming to IS-16205 Pt-24 with antirodent and non flame propogating properties of approved colour complete with fittings i.e.coupler,Tee, elbow clamp for cable protection of size 16 Sqmm 4 core complete all as specified and directed.

S & F in replacement Busbar panel weather proof outdoor type single door, fabricated out of 3.15 mm thick CRCA sheet with epoxy powder coating of RAL-7032 ( Siemens Gray) shade with matt finish with seven tank pre treatment process. The Panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-54, Gaskets between all adjacent units and beneath all covers shall be provided to render the joints dust proof. All doors and covers shall be provided with cylindrical panel locks and shall be fully gasketed with neoprene rubber and shall be lockable. The panel shall be provided with aluminium bus bars electrolytic grade of 200 amps current rating. The bus bars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & black colour coding and fix horizontally. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in a dedicated compartment. All joints and connection shall be done with galvanised or cadmium plated high tensile nuts, bolts, washers and AL Lugs etc. The panel shall be provided with 04 Nos 25mmx25mmx4mm thick angle iron supports of not less than each 0.6mtr height duly painted with anti corrosive black paint including earth work and grouted in PCC 1:3:6 at suitable depth as per site requirement including taking down existing one. The overall size of the Busbar panel shall not be less than 600mmx300mmx600mm (LxDxH)including 4 Nos cable entry holes suitable for cable entry up 3.5 C 50 Sqmm at bottom complete all as specified and directed Engr in Chrage. (a) MCCB 4 Pole, 415 Volts, 100 Amp, 16 KA Breaking capacity with adjustable Thermal and adjustable Magnetic overload protection with Ics = 100% of Icu including suitable size of spreader links and phase separator on both side. (Incoming) - 01 No. (b) MCCB 4 Pole, 415 Volts, 100 Amp, 16 KA Breaking capacity with adjustable Thermal and adjustable Magnetic overload protection with Ics = 100% of Icu including suitable size of spreader links and phase separator on both side. (Outgoing) - 01 No. (c) MCB 4 Pole, 415 Volts, 63 Amp, 10 KA Breaking capacity conforms to IEC 60947-2. (Outgoing) - 02 Nos.

Supply, installation, testing and commissioning in replacement of LT Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-54, front side double door type with locking arrangement and nut-bolts for back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber. The panel shall be provided with aluminium bus bars, electrolytic grade of 250 Amp Current rating. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and Cable connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers including suitable Lugs etc. The panel shall be provided with digital multifunction meter 4410 Series, Accuracy Class 1 with RS 485 Parameters with cast Resign CTs and RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board etc. The panel shall be provided 4 Nos 50x50x6mm thick angle iron supports of not less than each 1 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both sided and suitable extended rotary handle for Incoming MCCB complete all as specified and as directed. The overall size of the panel shall not less than 1600mmX400mmX 1600mm (LxDxH). The panel shall be provided for Cable entry from bottom side for 04 No of Cable upto 240 Sqmm 3.5 Core with suitable size of SS Cable Glands including 2 Nos of Earting Terminals one on each side of the Panel with earth strip and including following accessories:- Note : Before manufacturing drawing and design of panel including size & length of busbar shall be approved by Engr-in-charge. (a) MCCB 4 Pole, 415 Volts, 160 Amp, 36 KA Breaking capacity with adjustable Thermal and adjustable Magnetic overload protection with Ics = 100% of Icu with extended rotary handle (ROH) mechanism including suitable size of spreader links and phase separator on both side. (Incoming) - 01 No. (b) MCCB 4 Pole, 415 Volts, 100 Amp, 16 KA Breaking capacity with adjustable Thermal and adjustable Magnetic overload protection with Ics = 100% of Icu including suitable size of spreader links and phase separator on both side. (Outgoing) - 02 No. (c) MCCB 4 Pole, 415 Volts, 63 Amp, 16 KA Breaking capacity with adjustable Thermal and adjustable Magnetic overload protection with Ics = 100% of Icu including suitable size of spreader links and phase separator on both side. (Outgoing) - 03 No. (d) MCB 4 Pole, 415 Volts, 63 Amp, 10 KA Breaking capacity conforms to IEC 60947-2. (Outgoing) - 02 Nos.

Supply, installation, testing and commissioning in replacement of LT Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-54, front side double door type with locking arrangement and nut-bolts for back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber. The panel shall be provided with aluminium bus bars, electrolytic grade of 300 Amp Current rating. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and Cable connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers including suitable Lugs etc. The panel shall be provided with digital multifunction meter 4410 Series, Accuracy Class 1 with RS 485 Parameters with cast Resign CTs and RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board etc. The panel shall be provided 4 Nos 50x50x6mm thick angle iron supports of not less than each 1 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both sided and suitable extended rotary handle for Incoming MCCB complete all as specified and as directed. The overall size of the panel shall not less than 1600mmX400mmX 1200mm (LxDxH). The panel shall be provided for Cable entry from bottom side for 04 No of Cable upto 240 Sqmm 3.5 Core with suitable size of SS Cable Glands including 2 Nos of Earting Terminals one on each side of the Panel with earth strip and including following accessories:- Note : Before manufacturing drawing and design of panel including size & length of busbar shall be approved by Engr-in-charge. (a) MCCB 4 Pole, 415 Volts, 200 Amp, 36 KA Breaking capacity with adjustable Thermal and adjustable Magnetic overload protection with Ics = 100% of Icu with extended rotary handle (ROH) mechanism including suitable size of spreader links and phase separator on both side. (Incoming) - 01 No. (b) MCCB 4 Pole, 415 Volts, 160 Amp, 36 KA Breaking capacity with adjustable Thermal and adjustable Magnetic overload protection with Ics = 100% of Icu with extended rotary handle (ROH) mechanism including suitable size of spreader links and phase separator on both side. (outgoing) - 01 No. (c) MCCB 4 Pole, 415 Volts, 100 Amp, 16 KA Breaking capacity with adjustable Thermal and adjustable Magnetic overload protection with Ics = 100% of Icu including suitable size of spreader links and phase separator on both side. (Outgoing) - 0 1 No. (d) MCCB 4 Pole, 415 Volts, 63 Amp, 16 KA Breaking capacity with adjustable Thermal and adjustable Magnetic overload protection with Ics = 100% of Icu including suitable size of spreader links and phase separator on both side. (Outgoing) - 02 No. (e) MCB 4 Pole, 415 Volts, 63 Amp, 10 KA Breaking capacity conforms to IEC 60947-2. (Outgoing) - 02 Nos.

S & Fix in replacement of Cable Route Marker made up of Cast Iron of dia 100 mm and thickness 4.65 mm with supporting angle iron of size 20 x 20 x 3 mm and height 1 mtr for stand including priming, painting and wirting of "MES LT CABLE" with Arrow Direction in suitable size of letter including necessary earthwork and grouted at suitable depth in PCC 1:3:6 Type C2 using 40 mm graded aggregate in mass concrete complete all as specified and directed at site by Engr-in-Charge.

M & L for earthing complete with galvanized steel earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.50 m deep below normal ground level in any type of soil strata, connected to galvanized iron strip 25 X 4 mm by means of bolts, nuts and washers of galvanised iron or steel all as shown in earth plate No 3 of MES schedule 1991 Part – I connected to Change over switch panel including necessary excavation and earth work, concrete pit & chamber,pit cover made of PCC 1:2:4 type B1 with lifting handle and Earth lead and 20mm Dia GI watering pipe medium grade, Funnel, wiremesh, etc. complete all as specified and directed

S&F in replacement of 12 Module Plexo boxes conform to EN 60439-3, wheather proof cabinets IP 65, IK-09-Cl-II, door and cabinet fully reversible, removable chasis and faceplates from 2-row versions up, position rail for modular products and moulded cases, spacing between rail 150 mm box colour light grey L750A, cover colour dark grey R746A including taking down existing one complete all as specified and directed.

S & F in replacement of MCB 4 Pole, 415 Volts, 50 Hz, 63 Amp, 10 KA, B-Curve conforms to IS/IEC 60898 including taking down existing one and install with mounting rail, links etc complete all as specified and directed.

S & F in replacement of MCB Single Pole, 230 Volts, 50 Hz, 40 Amp, 10 KA, B-Curve conforms to IS/IEC 60898 including taking down existing one and install with mounting rail, links etc complete all as specified and directed.

Supply & Fix including commissioning digital automatic timer switch distribution panel board, factory assembled in powder coated steel sheet enclosure, comprising of 4P MCB, 40 Amps & 3 Pole power contactor 40/50 Amps and 230V digital time switch for controlling LED street lights, including earth work for fixing Timer switch distribution panel board and shall be provided 4 Nos 20x20x3mm thick angle iron supports of not less than each 0.6 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth complete all as specified and directed

S&F in replacement of Plexo box & adopter with PVC membrane of 3 Module IP-55 including 01 no of 15 Amps socket and 15 amp switch all as specified and directed Make: Legrand Catpart No 601932 or equvaleint make as mentioned at makes list in PS