Military Engineer Services Tender

All as per item Sr No. 2.00 here-in-before but cross sectional area 25 sqmm ,3.5 core ,complete all as specified and directed.

All as per item Sr No. 2.00 here-in-before but cross sectional area 16 sqmm ,4 core ,complete all as specified and directed.

All as per item Sr No. 2.00 here-in-before but cross sectional area 10 sqmm ,4 core ,complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5M in depth for laying of cables, poles, stay and getting out of excavated material, complete all as specified and directed.

Excavation in trenches in hard/dense soil/ hard standing not exceeding 1.5 meter wide and not exceeding 1.5M in depth for laying of cables, poles, stay and getting out of excavated material, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick each, by using excavated soil in trenches after the cables have been laid and tested ,complete all as specified and directed.

Removal of surplus soil to a distance not exc. 50m and deposited where directed at a level not exc. 1.5 m above the starting point ,complete all as specified and directed.

Supply and fix Double wall Corrugated High Density Polymer Ethylene (HDPE) pipe For laying of Electric cable of size 50mm outer diameter and 38 mm inner diameter with IS 16205 (Part 24) 1: 2018 laid in trenches, wall, floor, pole including bends, sockets and other connected accessories, complete all as specified and directed.

Supply and fix Double wall Corrugated High Density Polymer Ethylene (HDPE) pipe For laying of Electric cable of size 63 mm outer diameter and 51 mm inner diameter with IS 16205 (Part 24) 1: 2018 laid in trenches,wall,floor,pole including bends, sockets and other connected accessories,complete all as specified and directed.

Material and labour for RCC slab type B0 1:2:4 for cable route indicators of size length 0.9M x 0.3 M x 0.065 M duly writing "MES LT/ HT cable duly painted with weather coat paint embeded in PCC 1:4:6 under ground at depth 0.4M complete all as specified and directed.

Material & Labour for Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of earth plate not less than 1.5m below ground level connected to galvanized iron earth strip 32 x 6 mm by means of bolts, nuts, check nuts, washers of galvanized iron and connected to main switch/control board upto 7.5m away from the earth electrode including excavation earth work, PCC chamber, RCC cover slab char coal, watering pipe, wire mesh lugs, earth lead protection pipe 15mm bore, light grade 7.5m long as applicable and as per plate No. 3 of SSR 2009 ,complete all as specified and directed. (a) Excavation and earth work in any type of soil. (b) Drilling of holes in electrode (c) PCC pit in cement concrete (1:2:4) type B-1 (d) 40 mm thick Pre-cast RCC cover with suitable handle. (e) Funnel with watering pipe of GI 20 mm nominal bore ,medium grade & copper lug etc. (f) 50 mm nominal bore medium grade GI protection pipe 7.50 m long for protection of earthing lead. (g) Requisite quantity of charcoal and common salt. (h) Connection to earthing test point and testing on completion.

Taking out unserviceable any type and size of Steel pole, RCC Pole, complete all as specified and as directed

Material and labour for steel tubular swaged pole complete with base plate, pole cap, nut bolt washer etc 8.5 meters long type 410 SP-22 swaged poles conforming to IS 2713 (Part-I to III) 1980 all as specified including two coats of black bitumen paint through out internally and externally upto planting depth and applying two coats of aluminum paint over one coat of red oxide primer (externally) and numbering of poles as directed, including excavation /earth work, PCC 1:4:8 type D-2 ( using 40mm graded aggregate) for pole foundations of size 600x600x1500mm height upto ground level and using PCC 1:2:4 B-1 for coping with size 450x450x300mm including necessary formwork complete all as specified and as directed.

Supply and fix in repairs thermoplastic cable entry junction boxes of size 250 x 220 x 135mm and IP-65 protection level with metric knock out fixed on poles with MS clamps, nuts, bolts and washers including MCB SPN, 6-32 amps, 'C' series, breaking capacity 10 KA, 'C' curve 240 volts, 50Hz including necessary incoming and outgoing electric connection with suitable size of copper lugs etc., separate (detachable) gland plate, bakelite connector 4 way 20 amp, dust and vermin proof, front door opening with hinges and locking arrangement,complete all as specified and directed.

Supply and fix in repairs Heat shrinkable straight through cable jointing kit for 1100 Volts grade cable joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 150 to 185 Sq mm ,complete all as specified and directed. Note :- Excavation and earth work ,returning and filling, removing involved shall be measured and paid seperatelay.

All as per item Sr No. 18.00 here-in-before but, cable of size 90 to 120 sqmm, complete all as specified and directed.

All as per item Sr No. 18.00 here-in-before but, cable of size 25 to 50 sqmm, complete all as specified and directed.

Supply and fix in repair LED street light luminaires of capcity 60 watts with pressure diecast aluminium housing heat resistance toughened glass, IP 66 protection complete with driver, 2.5 sqmm 2 core multistranded aluminium wire for connection from street light fitting to OH line or junction box, and fixing accessories complete all as specified and directed. Make :- Cat No. LSTR01S060XC of Jaquar or equivalent as approved from specified makes.

Supply and fix in repairs LED driver for 60W LED street light fittings complete all as specified and as directed

Supply and fix in repairs LED driver for 45W LED street light fittings complete all as specified and as directed

Supply and fixing in repair retro reflective boards in shape of rectangle of size 1.0 m x1.4 m made out of 2 mm thick stainless steel both side bounded/pasted with high prismatic, sheet mannufactured by avery dennison or 3 M with desired letters /logos designed as directed the board shall be supplied with and including stainless steel frame made out of 25mm dia pipe in frame around duly welded with and including stainless steel sheet and stainless steel posts of 38 mm dia and full length of 2.20 m one side and 2.8 m other side complete all as specified and directed. Note : (i) Rate for fixing of boards with PCC 1:2:4 type B2 filling of size 45x45x60 cm to be incl in unit rate. (ii) The board should be written description as directed by Engineer-in-Charge.

Taking out unserviceable LT panel/feeder pillar of any size complete with accessories , complete all as specified and as directed

Supply, install, testing and commissioning of LT panel board / feeder pillar box, outdoor cubicle type, vermin proof, dust proof (of CPRI approved manufacturer), fixed on 50x50x5mm MS angle iron frame fixed 300mm above ground level and 450mm below the ground level grouted in and including PCC 1:3:6 type C1 (using 20mm grade stone aggregate) and plane made out of 3.00 mm thick CRCA sheet for both outer shell and 2.00mm thick for inner shell both side open able supported on and including ISMC 75 X 40mm powder coated steel frame and totally powder coated with epoxy siemen grey colour from inside and outside with locking arrangement and fixing arrangement i.e nuts, bolts, washers, clamps etc, with naturally air cooled epoxy insulated aluminium busbar TPN suitable for 1000 Amps with detachable gland plate for incoming and outgoing cable including termination of cable ends both incoming and outgoing with sufficient working space inside complete,all control cables shall be of 2.5 Sqmm copper multi stranded conductors and shall be properly bunched with suitable size binding materials , ferruled for proper identification of colour codes and crimped with adequate size of lugs also to accommodate and consisting of the following items, all as specified and as directed . Make :- L&T / Legrand / Standard / Universal Switchgear / C&S Electric Ltd or equivalent. Location : GRC Records Office Sub Stn. Contd...26.01

Contd..26.00 (a) Busbar chamber for 3 phase & nuetral of capacity 1000 Amps (100mm x 10mm) aluminium bus bar duly insulated. (b) Multifunctioning meter to measure Voltage, ampere, KWH, PF -01 No (c) one set of pilot lamp. (d) Incoming 630 Amps ACB 4 Pole, 415 V, Manual Drawout type with microprocessor release. - 01 No (e) Outgoing MCCB 200 Amps 4 Pole 415 volts , Adjustable type, 36 KA Ics=100% of Icu thermal magnetic setting - 04 Nos (f) Outgoing MCCB 100 Amps 4 Pole 415 volts , Adjustable type, 36 KA Ics=100% of Icu thermal magnetic setting - 02 Nos (g) Outgoing MCCB 125 Amps 3 Pole 415 volts , Adjustable type, 16 kA Ics=100% of Icu thermal magnetic setting - 02 Nos (h) Outgoing MCCB 63 Amps 3 Pole 415 volts , Adjustable type, 16 kA Ics=100% of Icu thermal magnetic setting - 03 Nos

Supply, install, test and commissioning of LT panel board / feeder pillar box, outdoor cubicle type, vermin proof, dust proof (of CPRI approved manufacturer), fixed on 50x50x5mm MS angle iron frame fixed 300mm above ground level and 450mm below the ground level grouted in and including PCC 1:3:6 type C1 (using 20mm grade stone aggregate) and plane made out of 3.00 mm thick CRCA sheet for both outer shell and 2.00mm thick for inner shell both side open able supported on and including ISMC 75 X 40mm powder coated steel frame and totally powder coated with epoxy siemen grey colour from inside and outside with locking arrangement and fixing arrangement i.e nuts, bolts, washers, clamps etc, with naturally air cooled epoxy insulated aluminium busbar TPN suitable for 1000 Amps with detachable gland plate for incoming and outgoing cable including termination of cable ends both incoming and outgoing with sufficient working space inside complete,all control cables shall be of 2.5 Sqmm copper multi stranded conductors and shall be properly bunched with suitable size binding materials , ferruled for proper identification of colour codes and crimped with adequate size of lugs also to accommodate and consisting of the following items, all as specified and as directed . Make :- L&T / Legrand / Standard / Universal Switchgear / C&S Electric Ltd or equivalent. Location :- MH Road Sub Stn (Near 13 No. MAP Offrs Qtr) Contd...27.01

Contd..27.00 (a) Busbar chamber for 3 phase & nuetral of capacity 1000 Amps (100mm x 10mm) aluminium bus bar duly insulated. (b) Multifunctioning meter to measure Voltage, ampere, KWH, PF -01 No (c) one set of pilot lamp. (d) Incoming 630 Amps ACB 4 Pole, 415 V, Manual Drawout type with microprocessor release. - 01 No (e) Outgoing MCCB 250 Amps 4 Pole 415 volts , Adjustable type, 36 kA Ics=100% of Icu thermal magnetic setting - 01 No (f) Outgoing MCCB 200 Amps 4 Pole 415 volts , Adjustable type, 36 kA Ics=100% of Icu thermal magnetic setting - 02 Nos (g) Outgoing MCCB 125 Amps 3 Pole 415 volts , Adjustable type, 16 kA Ics=100% of Icu thermal magnetic setting - 02 Nos (h) Outgoing MCCB 63 Amps 3 Pole 415 volts , Adjustable type, 16 kA Ics=100% of Icu thermal magnetic setting - 03 Nos

Supply, install, test and commissioning of LT panel board / feeder pillar box, outdoor cubicle type, vermin proof, dust proof (of CPRI approved manufacturer), fixed on 50x50x5mm MS angle iron frame fixed 300mm above ground level and 450mm below the ground level grouted in and including PCC 1:3:6 type C1 (using 20mm grade stone aggregate) and plane made out of 3.00 mm thick CRCA sheet for both outer shell and 2.00mm thick for inner shell both side open able supported on and including ISMC 75 X 40mm powder coated steel frame and totally powder coated with epoxy siemen grey colour from inside and outside with locking arrangement and fixing arrangement i.e nuts, bolts, washers, clamps etc, with naturally air cooled epoxy insulated aluminium busbar TPN suitable for 1000 Amps with detachable gland plate for incoming and outgoing cable including termination of cable ends both incoming and outgoing with sufficient working space inside complete,all control cables shall be of 2.5 Sqmm copper multi stranded conductors and shall be properly bunched with suitable size binding materials , ferruled for proper identification of colour codes and crimped with adequate size of lugs also to accommodate and consisting of the following items, all as specified and as directed . Make :- L&T / Legrand / Standard / Universal Switchgear / C&S Electric Ltd or equivalent.

Contd..28.00 (a) Busbar chamber for 3 phase & nuetral of capacity 600 Amps (60mm x 10mm) aluminium bus bar duly insulated. (b) Multifunctioning meter to measure Voltage, ampere, KWH, PF -01 No (c) one set of pilot lamp. (d) Incoming MCCB 400 Amps 4 Pole 415 volts , Adjustable type, 36 kA Ics=100% of Icu thermal magnetic setting - 01 No (e) Outgoing MCCB 160 Amps 4 Pole 415 volts , Adjustable type, 36 kA Ics=100% of Icu thermal magnetic setting - 05 Nos (f) Outgoing MCCB 63 Amps 3 Pole 415 volts , Adjustable type, 16 kA Ics=100% of Icu thermal magnetic setting - 03 Nos

Supply & install test & commissioning of out door type feeder pillar box weather proof cubical type fabricated out of 3 mm thick MS angle with front door with locking arrangement consisting of aluminium bus bar suitable for AC 415V, 3 Phase and neutral 400 Amps rating mounted on insulator and enclosure of appropriated size made out of 2 mm thick MS sheet to house cubicals MCCBs units with interlocking arrange-ments are given below complete with two coats of synthetic enamel paints over a coat of red oxide primer danger board on the front side the whole frame suitable grouted and mounted on and including PCC pillars of adequate strength to take the weight consisting of the following. Make :- L&T / Legrand / Standard / Universal Switchgear / C&S Electric Ltd or equivalent. (a) MCCB 200 A, 36 KA, 4 Pole, 415 Volt, 50 Hz as incommer - 01 No (b) MCCB 160 A, 36 KA, 4 Pole, 415 Volt, 50 Hz as outgoing - 02 Nos

S&F in repair MCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA,Ics=100% of Icu complete all as specified and as directed.

S&F in repair MCCB 4 Pole, 415 V, Adjustable type, 200 Amps with breaking capacity 36 KA ,Ics=100% of Icu complete all as specified and as directed.

S&F in repair MCCB 4 Pole, 415 V, Adjustable type, 320 Amps with breaking capacity 50 KA, Ics=100% of Icu complete all as specified and as directed.

Material and labour for PCC Type D2 ,1:4:8 ( by using 40 mm graded stone aggregate ) in lintels upto 1.5m clear span, cills, steps; seismicand other similar bands, plinth courses, string courses, lacing courses, parapets andrailings upto 60 cm in height, copings, complete all as specified and directed.

M&L for PCC Type B1 1:2:4 ( by using 20 mmgraded stone aggregate ) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets andrailings upto 60 cm in height, copings, complete all as specified and directed.

Material and labour rendering 10 mm thick plaster on fair faces of brickwork or concrete sur faces in CM 1:4 all as finishing the surface , complete all as specified and directed.

Material and labour Mild steel fabrication works such as angle / FI clamp, MS pipe nuts, bolts, washers welding, bending cold or hot drilling holes for bolts in any shape and size etc including two coats of synthetic enamel paint cover a coat of red oxide primer complete all as specified and directed.

Material and labour for loose filling with aggregates of gauge 40 to 80 mm crushed stone back colour suitable for spreading in electrical sub stn after preparation site by removing all type of debris, removing unwanted soil, and spreading lime powder beneath the aggregate complete all as specified and directed.

Supply and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, 4 sqmm 2 core, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire complete all as specified and directed.

Supply and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, 6 sqmm 2 core, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4 mm suspension wire complete all as specified and directed.

Supply and fix 1100 Volts grade Copper conductor, PVC insulated, round sheathed (flexible), industrial cable, 1.5 sqmm 3 core complete all as specified and directed.

Supply and fixing LED flood light 200 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP-66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specified and directed.

Supply and fixing LED focus light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP-66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specified and as directed.

Supply and fixing Automatic Load Transfer Switch Changeover 63 Amps, 4 Pole with CM 331 Controller, 415 Volts, with 16 A DP MCB for protection with all all control wiring , incoming and outgoing connection with cable lugs, washers, nutbolts, Sheet Enclosure Box (2mm thick sheet ) which is suitable of outdoor and accessories complete with taking down old unserviceable changeover switch all as specified and as directed. Make :- HPL Item code ATS063 4 POS or equivalent as approved

Supply and fixing Automatic Load Transfer Switch Changeover 100 Amps, 4 Pole with CM 331 Controller, 415 Volts, with 16 A DP MCB for protection with all control wiring , incoming and outgoing connection with cable lugs, washers, nutbolts, Sheet Enclosure Box (2mm thick sheet ) which is suitable of outdoor and accessories complete with taking down old unserviceable changeover switch all as specified and as directed. Make :- HPL Item code ATS100 4 POS or equivalent as approved

Supply and fixing of Automatic Street light Timer Switch using combination of NATURE SWITCH AND ANALOG TIMER (DUAL TYPE) for automatic switching of street lights based on LUX level of natural light consisting with Sensor (Natural Switch) along with suitable power contractor, MCB and support terminals should be enclosed in pole/ wall mountable enclosure made out of Rust proof, Electric shock proof, termite proof and FR grade SMC junction Box conforming to IP 54 protection of capacity 12 KW 3 phase 4 wire (3 separate power contactor) including all accessories and fixing arrangement complete all as specified and directed. Cat No. Swadeep - 02EC-12 KW3P-DUAL or equivalent as approved

NOTE : SCHEDULE OF CREDIT (Amount on page No 50 shall be deducted offline from the total quoted amount to arrive at the net contract sum to be considered for acceptance [(-) Rs 70508/- ].