Dr Babasaheb Ambedkar Marathwada University Tender

Upgradation, Maintenance and Buyback of Existing Switching Network

Upgradation, Maintenance and Buyback of D-Link DGS3627G 2 Numbers without SFP Module High performance Managed Stackable Core/Data Center Switch - 48-port Proposed switch should have 48 ports of 1G/10G/25G which can accommodate 1G transceivers, 10G transceivers & 25G fiber transceivers Proposed switch should have at least 4 ports of 40G/100G for uplink Switch should Support Internal hot swappable Redundant Power Supplies. Switch shall have SD Card slot/USB/External flash for easy file store & restoration like firmware, configuration file, boot image, syslog etc.Switching Capacity should be wire speed with a min of 3.2Tbps of switching capacity Switching throughput (Forwarding rate) should be a min of 1Bpps to be wire speed Proposed switch shall support min 82,000 MAC addresses Proposed switch shall support min 82,000 IPv4 route entries Switch should support virtual Stacking of min 4 units per stack. Stacking bandwidth should be at least 200Gbps per switch. Stacking ports should be separate and in addition to the above-mentioned ports. Necessary cables/interfaces should be provided with each switch for stacking from day-1 The LAN switch shall have IEEE 802.1Q VLAN encapsulation and should support 4k Vlans. It shall have support for Detection of Unidirectional links and to disable them to avoid problems such as spanning tree loops It shall support 802.1v Protocol-based VLAN Should support MAC based Vlans Should have 802.1D STP, 802.1w RSTP and 802.1s MSTP Spanning Tree Protocol The Switch should have 802.1AX Link Aggregation of 8 links per group and upto 8 groups per device Port Mirroring One to one/Many to One, Flow based mirroring & VLAN Mirroring The Switch shall have the intelligence to detect the loop occurring from the unmanaged network segment Switch should support Static routing for IPv4 and IPv6, RIP for IPv4 and RIPng for IPv6, OSPF,OSPF v3. Necessary licenses should be quoted from day-1 Switch should support IGMP v1/v2/v3, PIM-SM and PIM-SSM Should have policy based routing. Should support VRRP Switch should support 802.1p priority queuing with 8 queues per port. It shall support RADIUS/TACACS+ authentication to enable centralized control of the switch and restrict unauthorized users from altering the configuration.It shall support for SSHv2, SNMPv3 to provide network security by encrypting administrator traffic Should support sFlow for monitoring traffic in data networks, SNMP v1, v2c, v3 and SNMP Traps and RMON. 3 years warranty should be included with the switches Transceivers should be from the same make as the switch manufacturer - 48 nos of 10G LR transceivers required per switch Switch should be quoted with the NMS/controller for Network monitoring, Device detection, Performance analysis, Device management, Fault management that supports GUI management and troubleshooting of minimum 100 devices. If a workstation/VM is required, please include workstation/VM pricing. Perpetual licensing/warranty/support for the NMS/Controller and workstation to be included into the proposal. Switch delivery should be within 6 weeks of the order placement considering urgencyPreference for Make in India, international brands with Make in India switches too are also permitted. Switch should be supplied with the all necessary hardware accessories like Power cord, Rack-mount bracket, Installation Guide, etc. and necessary software image file to fulfill all above mention feature set from day 1.

Upgradation, Maintenance and Buyback of CISCO SG300-28 28-Port Gigabit Managed Switch + 2 Mini GBIC Ports without SFP Module and CISCO SG95-24 Compact 24-port Unmanaged Gigabit Switch + 2 Mini GBIC Ports without SFP Module with 24 port Layer 2/Layer 3 Gigabit Switch Switch with at least 24 X 10/100/1000 RJ-45 Gigabit Ethernet Ports and 2/4 x 10G SFP+ Ports. Switching capacity should be 128 Gbps or higher or non-blocking architecture. Switch packet forwarding rate should be 95 Mpps or higher or non-blocking architecture. Proposed switch shall support min 16K MAC addresses Switch should be standard 1U rack mountable. Support for the Energy Efficient Ethernet (IEEE 802.3az) standard. Power input should be 100 to 240 VAC, 50/60 Hz, internal power supply. Proposed switch shall be stackable with support for at least 8 switches in a stack for future ease of management. Stacking bandwidth should be at least 40Gbps per switch Operating temperature should be 5 degree Celsius to +50 degree Celsius. Support Jumbo Frame up to 9K Bytes or higher. Should have 802.1D STP, 802.1w RSTP and 802.1s MSTP Spanning Tree Protocol. Should support Spanning tree Root restriction Should support Loopback detection (LBD) to detect the loop created by a specific port. Switch should support IEEE 802.1Q VLAN tagging for Ethernet frames and support for 4096 VLANs Different type of VLAN like Port based, Auto Surveillance, Auto Voice, Asymmetric Vlan etc. should be available for configuration. Switch should support QoS (quality of service) IEEE 802.1P for traffic prioritization. It should support 8 queues per port. Different type of QoS priority like Strict Priority Queue and Weighted Round Robin. Switch should support for static routes, RIP, OSPF for both IPv4 and IPv6. All necessary licenses to be quoted Support ACLs configurable by IPv4, MAC and IPv6 Should support port security to secures the access port based on MAC address. should have broadcast, multicast, and unicast storm control to prevents faulty end stations from degrading overall systems performance. Should have SSH and SSL for IPv4 and IPv6. Should support 802.1X port based authentication. Should support ARP inspection Should support DHCP snooping and DHCP relay. Switch should able to create a binding table for IP + MAC + Port to prevents a malicious user from spoofing or to restrict the unauthorized users. Should support 802.1X RADIUS/TACACS+ Should support SNMP v1, v2c, v3 and SNMP Traps and Remote Monitoring (RMON). Should have SNTP/NTP protocol for time synchronization. Should support Link Layer Discovery Protocol (LLDP) and LLDP-MED. 3 years warranty should be included with the switches Transceivers should be from the same make as the switch manufacturer - 1 nos 10 G of LR per switch Switch should be supplied with the all necessary components like Power cord, Rack-mount bracket, Installation Guide, etc. and necessary software image file to fulfil all above mention feature set from day 1. Switch should be quoted with the NMS/controller for Network monitoring, Device detection, Performance analysis, Device management, Fault management that supports GUI management and troubleshooting of minimum 100 devices. If a workstation/VM is required, please include workstation/VM pricing. Perpetual licensing/warranty/support for the NMS/Controller and workstation to be included into the proposal. Preference for Make in India, international brands with Make in India switches too are also permitted.