Bhabha Atomic Research Centre Tender

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 100 m lead For thickness of tiles above 10 mm and up to 25 mm

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 100 m lead For thickness of tiles above 25 mm and up to 40 mm

Dismantling old plaster / skirting carefully, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 100 m lead

Dismantling doors, windows and clear storey openings (steel / wood) shutter including chowkhats, architraves, holdfasts etc. complete and stacking within 100 m lead (full windows) Of area 3.00 Sq.M and below

Dismantling doors, windlows and clear storey windows (steel / wood) shutter including chowkhats, architraves, holdfasts etc. complete and stacking within 100 m lead (full windows) Of area beyond 3.00 Sq.M

Dismantling Aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplaus material and stacking of serviceable materials within 100 m lead as directed by the Engineer-in-charge

LEAD CHARGES FOR LEAD OF DEBRIS by mechanical transport including loading, unloading, stacking / levelling etc. Notes : 1. The rates are applicable for NET Quantities arrived after making deduction for voids @ 30% from corresponding TRUCK Measurement. 2. Finding authorised ground for disposing debries, transporting of debries at disposal ground, disposing, stacking, leveling & statutory charges if any will be responsibility of the Contractor and no extra charges shall be paid for the same. The debris from identified area shall be cleared every week after accumulation of minimum one Truck Load.

Debris Beyond 4 Km but up to and including 5 Km.

Debris Beyond 5 Km for every 1KM or part thereof

Providing structural repairs in old damaged concrete structures / surfaces with approved Polymer with following operations 1) Removal of loose/Spalled or damaged concrete by chipping and cleaning the concrete surface and reinforcement steel with wire brush and with water 2) Cleaning the re bars with Acetone for complete rust removal and washing with water to make the surface clean. 3) Applying protective coat / bond coat using polymer and cement in the proportion of 1; 1.5 (1 part of polymer and 1.5 parts of cement in synthetic enamal paint like consistancy with brush 4) Reinstate the area with polymer modified mortar in layers of maximum 20 mm with the proportion of Cement 50 Kg : washed and dried river sand 87.50 kg ; silica sand 37.50 Kg. mixed with 10 litres of Polymer (or 1 Kg cement : 1.75 kg washed and dried river sand ; 0.75 Kg silica sand : 200 ml polymer) 5) If thickness of repair exceeds 20mm , after every 20 mm thick repair, bond coat as per 2 above to be applied and further thick of repair to be continued for each layer. This work is inclusive of all materials, labour, complete all as directed at site using approved polymer suitable for structural repair shall be used) Note: Scaffolding will be paid seperately under relevant item

Extra over 120 mm thick cement based water proofing for providing and laying brick bat coba in roof (i) Laying brick bats with mortar using broken brick bats 25 mm to 115 mm size with 50% of cement mortar 1:4 (using crushed sand) admixed with proprietary water proofing compound as per manufacturer's specifications conforming to relevant IS and approved by Engineer-in-charge over 20 mm thick layer of C.M 1:4 (using crushed sand) to required slope complete as directed by the Engineer-in-charge. (Measurement will be over and above the average thickness of 120 mm only)

Providing and laying in position cement concrete of 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc. complete as per specification and drawings but excluding the cost of Formwork shuttering, centering and steel reinforcement at all Levels

Providing, centering, shuttering Form work using steel plates, timber planks for all types of structures including necessary strutting, proping, staging, supports, bracings etc. and deshuttering the same after the specified time all as per drawings, specifications and as directed by the Engineer-in-charge at all levels

In Superstructure

Providing and Laying Autoclaved Aerated cement block masonry of approved make with specified thick AAC Blocks in Super structure above plinth level up to 20 m height in cement mortar 1:4 (using crushed sand). The rate shall also include providing and placing in position 2 nos of 8 mm dia bars at every third course of the masonry work

Providing 15 mm thick Internal plaster in cement mortar 1:4 without cement punning (using Crushed Sand) finished smooth, including sieving of sand to required fineness, preparation of the surface, scaffolding, curing all as per specifications, drawings and as directed at site complete.

Providing 20 mm thick External plastering in two coats under layer 12 mm thick with C.M 1:4 (using crushed sand) finished with a top layer 8 mm thick in C. M 1:3 (using crushed sand) including approved water proofing compound @ 2% by weight of cement or as per manufacturer's specifications, sieving of sand to required fineness, scaffolding up to 10 metres height, finishing, curing etc. complete as per specifications. and as directed by the Engineer-in-charge

Providing REINFORCEMENT FOR REINFORCED CEMENT CONCRETE at all levels including supplying, preparation of bar bending schedules,cutting, bending, transporting, fixing, tieing in position with 1.6 mm dia soft drawn annealed binding wire all labour charges, cost of cover blocks in specified grade of concrete etc. complete including cost of binding wire as per specifications and drawings. Steel Supplied by the Contractor. Using TMT bars of specified grade all dia bars to be supplied by the contractor confirming to IS:1786 only.

Providing STRUCTURAL STEEL WORK USING ANGLES, CHANNELS, JOISTS AND OTHER SECTIONS, welded and / or bolted in built up sections for trusses , structural steel floors, frame works, monorails and other structures including supplying, cutting, welding, fabricating, hoisting, fixing in position, applying a priming coat of approved steel primer etc. complete all as per specifications, drawings and as directed by the Project Engineer. Up to and including 300mm Joists, 350mm channels, and below sections Using materials of confirming to IS:2062 only. All test reports to be provided along with the supply of the materials. 'Notes : '(1) Welding weights, connections, bolts and nuts, anchor bolts shall not be measured for payment, but the cost of which shall be deemed to have been included in the rate. '(2) All holes will be made by drilling only. Gas cutting of holes will not be permitted. (3) Edges of plates shall be grinded to uniform smooth finish. '(4) Full length welding shall be carried out as directed by the EIC. Note : Tentative/suggested make for the guidance of the bidder (s) : M/s. ADOR, ESAB, Indian Oxygen and D&H SECHERON or equivalent make - Welding Electrodes.

Providing Structural steel work in M.S Plain Plates and chequrred Plates for Embedded Parts, Trench Covers, Connection plates etc.including cutting, hoisting, fixing in position and applying a priming coat of approved zinc chromate steel primer etc.including cost of structural steel Plates, welding all labour charges etc. complete as per drawings and specifications. Using materials of confirming to IS:2062 only. All test reports to be provided along with the supply of the materials. 'Notes : '(1) Welding weights, connections, bolts and nuts, anchor bolts shall not be measured for payment, but the cost of which shall be deemed to have been included in the rate. '(2) All holes will be made by drilling only. Gas cutting of holes will not be permitted. (3) Edges of plates shall be grinded to uniform smooth finish. '(4) Full length welding shall be carried out as directed by the EIC. Note : Tentative/suggested make for the guidance of the bidder (s) : M/s. ADOR, ESAB, Indian Oxygen and D&H SECHERON or equivalent make - Welding Electrodes.

Providing and fixing 15-17 mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut Granite of Jet Black colour for kitchen platforms, vanitiy counters, wash basin counters, door frames, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (using crushed sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edges to give high gloss finish etc. complete at all levels

Extra for providing edge moulding to 17 mm thick marble stone / Granite Slab counters, Vanitis etc. including machine polishing to edge to give high gloss finish et. Complete as per design approved by Engineer-in-charge.-Granite work

CUDDAPAH STONE SLAB OVER KITCHEN PLATFORM etc. using 25 mm to 30 mm thick machine cut double machine polished slabs in single piece upto a maximum length of 1.80 metres laid over 20 mm thick cement mortar bedding 1:4 finished to proper levels, cured etc. complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS 15622 of approved make. shade and colour of size ranging from 300 - 600 mm long and 300 mm - 600 mm wide and thickness not less than 6 mm as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (using crushed sand), setting the tiles in cement slurry and pointing the joints with matching colour Tile grout of approved make of matching shade including using PVC tile trim in the exposed corners, complete as per drawings, patterns and specifications complete as directed by the Engineer-in-charge.

Providing and fixing Glazed VITRIFIED floor tiles of approved make in different sizes conforming to IS 15622 in all colours and shades in Glossy or Matt or satin finish laid over a bed of minimum 20 mm thick bed of cement mortar 1:4 (using Crushed sand) and jointing with grey cement slurry including grouting with the joints with white cement based Tile Grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge. Using Tiles of size above 600x 600mm and up to and including 900 x 900mm

Add Extra for polymer mortar in place of cement mortar

Providing and laying FLOORING PLASTER OF PARIS 8mm THICK OVER NEW LAID TILES including spreading polythene paper, curing, levelling,removal and disposal of same before cleaning floor, labour, tools etc. complete and as directed by Engineer in charge.

Providing, supplying and laying pre polished granite slab flooring / dado / Wall cladding with 15-17 mm thick granite slabs over 20 mm thick base cement mortar 1:4 (using crushed sand) laid and placed with grey cement slurry including filling the joints with matching white cement based tile grout complete all as per specifications and drawings.

Using approved shades other than black

Extra over for Granite cutting using water jet

Providing and fixing anodized aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per drawings and and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealent etc. (fittings glazing and panelling shall be paid for separately)

Anodised Aluminium sections (Minimum anodizing thickness of 15 micron)

Extra for colour anodizing

Providng and fixing aluminium grill in natural Silver anodising of min 15 Microns with a opening size of 60mm x 45mm and Minimum weight of 4.12 Kg/ Sq.M including providing and fixing Suitable 'F' / 'H' section outer frame and mullion fixing with screws complete all as per specifications and as directed at site by the Engineer-in-charge .Aluminium alloy shall be of 6063-T6 with yield strength of minimum 6.5 kg/ sq.mm. Note : Tentative/suggested make for the guidance of the bidder (s) : M/s. "DECO GRILLE" make Model No. DG- 202 or equivalent make

Extra for providing Aluminium Grill 10 mm thick with colour anodised by the manufacturer (Champagne, black, Bronze, Gold colours) complete all as per specifications and as directed at site by the Engineer-in-charge

Providing and fixing 25 mm thick Colour PVC Integral Foam Sheet door shutters flush door of approved colour, of approved make or equivalent, design, colour and fixing with 4 Nos 100 mm (ISI marked) stainless steel hinges, Fixing of Stoppers, tower bolts, baby latch, aldrop, handles etc.wherever required with S.S. screws (Stopper, Tower bolt, Baby latch, Aldrop, Handels etc Shall be supplied by department) etc. complete as per specifications and as directed by Engineer-in-charge. Note : The door should satisy the following technical parameters as under: 1. Density : 0.475 to 0.55 g/cc, 2. Hardness (Shore 'D'): min. 55, 3. Water absorption : max. 1 %, 4. Tensile strength : min. 13 MPa, 5. Elongation : min. 15 %, 6. Flextural Strength min. 30 MPa, 7. Compressive Strength at 10% Deformation : min. 3 MPa, 8. Vicat Softening Temperature: more than 75 Deg Celcius 9. Flammability: classification B : S3 : D0 (to be tested as per NF EN 13501-1 standard)

Designing, providing and fixing of 4 mm thick approved make and shade Aluminium Composite Metal Panel of approved make cladding at different locations including soffits of over-hangs and including aluminium frame work with grids filled in with weather silicon sealant as per the drawings. The ACM panel composition shall be of 0.5 mm thick PVDF coated aluminium sheet + 3 mm thick low density polyethelene virgin resin core + 0.5 mm thick polyester (PVDF) coated Aluminium sheet all complete as per approved shop drawings and specification Note : ACMP shall be measured to the actual visible area of the ACP sheet including silicon joints as fixed on site.

Providing and fixing IS:12817 marked stainles steel butt hinges of size 100 x 60 x 2.5mm (heavy weight) of approved make with stainless steel screws etc. complete as directed by the Engineer-in-charge.

Providing and fixing Approved Quality and shape LOCKS cum Handle of approved equivalent make for Sliding shutters. Note : Tentative/suggested make for the guidance of the bidder (s) : M/s. Star Locks or equivalent make

Providing and fixing approved quality stain less steel body roller wheels of approved make for sliding shutters

Providing and fixing glazing in aluminium doors, window, ventilator shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item)

With clear float glass panes of 6.00 mm thickness

With frosted glass panes of 6.00 mm thickness

Providing and fixing aluminium hanging heavy quality floor door stopper ISI marked with twin rubber stoppers, anodised transparent or dyed to required colour or shade with necessary screws etc. complete.

Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer of approved make with necessary accessories and screws etc. in wooden doors / steel doors with necessary bolts & nuts complete as per specifications and as directed by the Engineer-in-charge.

Filling the gap between aluminium frame & adjacent RCC / Brick work / Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge etc. complete Up to 5 mm depth and 5 mm width

Providing and fixing satin finish stainless steel AISI 304 (18/8) kitchen sink of size 610 x 510 mm without drain board and bowl size 685 x 535 x 250 mm depth as per IS13983 of approved make with C.I. brackets, fittings and stainless steel plug 40 mm including painting the fittings and brackets with 3 coats of white enamel paint over a coat of primer, cutting and making good the walls wherever requried complete as per specifications and as directed by the Engineer-in-charge.

Providing and fixing anodised aluminium tower bolts of size 250 X 12 mm ISI marked of approved make, transparent or dyed to requried colour or shade with necessary screws etc.

Providing and fixing anodised aluminium baby latch of size 75 X 12 mm ISI marked of approved make transparent or dyed to requried colour or shade with necessary screws etc.

Providing and fixing mortice latch and lock of approved make with 6 levers and a pair of handles Inside opening LEFT / Right with necessary screws etc complete suitable for fixing in wooden / steel/ FRP/ doors as per specifications.

Providing and fixing 4 Lever Mortice Lock of approved make suitable for aluminium sections

Providing and fixing aluminium handles 175 mm long Inner grip 125 mm with 12 mm dia rod plate type BOW handles ISI marked of approved make, anodised transparent or dyed to req. colour or shade with necessary screws etc. complete.

Supplying, providing and fixing STAINLESS STEEL-304 D-HANDLES (MATT FINISH) OF LENGTH - 300mm, DIAMETER-25mm, suitable S.S. fange , S.S. cap and thickness 16 Guage thickness to brick Walls, R.C.C. surface, Wooden doors etc. including drilling, S.S. Screws of 30mm long ( 6 Nos for each handle) ,cost of labour, tools, tackles ,wooden gutties, plants, transportaion, scaffolding etc. all complete as per site requirement and as directed by Engineer in charge.

Providing and fixing STAINLESS STEEL ALDROPS OF SIZE 300mm X 14mm of approved make with necessary screws, bolting from rear side complete as per specifications complete.

Providing and fixing cement bonded particle board of approved make or approved equivalent with washer, flange type screws etc. for claddings / flooring over existing frame work, as per manufacturers specification and directed of Engineer-in-charge. For 12mm thick cement board for partition & false ceiling. Note :- Aluminium required for framework & joint covering will be measured separatly and paid under relavant Item of this schedule. Only actual covered area of the cement bonded particle board will be measured and paid under this item.

Providing, supplying & fixing of S.S. MESH-(MOSQUITO NET) - 0.50MM THICK - LESS THAN 1.0 SQ. MM APERTURE in aluminium grill / frame including cost of all accessories and fabricating to required sizes etc complete all as directed by the Engineer-in-Charge. Alumunium Grill will be paid separately

Providing and fixing hand rail using 304 grade Stainless Steel pipes & other SS sections of approved size and make and quality by welding, mirror / matt polishing, fixing at site etc. for balcony railing & staircases railing, grill, drain cover, counter, racks etc. including special sections as per drawings, specifications. complete as directed by the Engineer-in-charge

Core cutting in RCC beyond 50 mm up to and including 100 mm Dia as directed by the Engineer-in-charge.

Providing, laying , jointing, fixing and testing heavy quality (ISI Marked C-Class) Galvanised Iron pipes and ISI marked fittings like, tees, elbows, bends, unions, nipples,reducers etc. as required for the work, including testing the pipes and fittings for 10.00 Kg / Sq.Cm hydralic pressure with a minimum period of two hours duration with clean water, including cutting , threading, jointing with hemp yarn, white lead, jointing teflon tape, chasing walls and making good by filling with concrete 1:3:6, complete all as per specifications and drawings, including two coats of anti corrosive bitumastic paint, all as directed by the Engineer-in-charge. Pipes with ISI marked 'C' -Class heavy quality pipes of approved make.

20 mm dia G.I pipe

25 mm dia G.I pipe

40 mm dia G.I pipe

50 mm dia G.I pipe

Providing & fixing in position heavy pattern screw down gun metal gate valve with handles and wheels of approved make including testing for 10Kg/cm2 pressure with clean and potable water with a minimum testing duration of two hours etc.as per specification and as directed by the Engineer-in-charge

20 mm n.b

25 mm n.b

40 mm n.b

50 mm n.b

Providing and fixing C.P brass Angle cock of heavy quality of specified / approved make, for wash basin inlet / flush cistern etc. as per specifications and as directed by the Engineer-in-charge - 15 mm n.b CP brass Angle cock of approved make

Providing and fixing C.P brass bib cock of heavy quality of specified / approved make as per specifications and as directed by the Engineer-in-charge- 15 mm dia bib cock self closing of approved Type and make

Providing and fixing 15 mm C.P brass 2 in 1 bib cock and Angle cock combination of Heavy Quality of approved make as per specifications and as directed by the Engineer-in-charge

Providing and fixing 15 mm PVC inlet connection suitable for hot and cold water 600 mm long with nuts and washers complete for wash basins/ Urinals etc. with all necessary acessories complete as directed by the Engineer-in-charge

Providing and fixing PVC low level / high level flushing cistern 10 litre capacity of approved make in white colour with flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures etc. complete as per specifications and as directed by the Engineer-in-charge.

Providing and fixing C.P brass concealed stop cock of Heavy Quality of specified / approved make as per specifications and as directed by the Engineer-in-charge - 15 mm n.b CP brass concealed stop cock of approved make

Providing and fixing square shape white matt finish, thin rim table top basin of size about 420mm x 420mm x 150mm including making all connections but excluding the cost of fittings all as directed by Engineer-in-charge.

Providing and fixing coupled white rectangular vitreous china European type Water Closet with 'P' or 'S' Trap with soft close slim solid seat cover and lid of approved make with integrated 10 litre low level white PVC flushing cistern with manually controlled device having dual flush (handle lever/button) conforming to IS:7231, flush bend, fixing EWC with C.P brass screws, 15 mm PVC heavy quality inlet connection of 450 mm long, including testing , commissioning & cleaning etc. complete all as per drawings and specifications and as directed by the Engineer-in-charge. E.W.C. pan in White colour with ISI marked white solid plastic seat and lid. Size: 365x630x750 mm, P Trap-180 mm

Providing and fixing Indian water closet (Orissa pan) of apperoved make with 100 mm China ware P or S trap, One no. 10 litre High level or low level white PVC flushing cistern with flush pipe & bend with manually controlled device (handle lever) conforming to IS:7231, PVC 15 mm Inlet connection with all fittings and fixtures complete including all connection, embedding in position commissioning, cleaning etc. all as per drawings and specifications and as directed by the Engineer-in-charge. White Vitreous china Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing heavy quality C.P .brass waste coupling of following dia for wash basin and sink, of approved make, size and quality all as directed complete- C.P Brass Waste coupling 32 mm Dia of approved make Half threaded or Full threaded as per requirement.

Providing and fixing heavy quality stainless steel / C.P brass grating of approved equvalent make as specified for floor traps / nahani traps all as directed by the Engineer-in-charge - SS grating 125 mm dia

Providing and fixing Heavy Quality 15 mm C.P brass fancy pillar cock of approved make quarter turn and type as per specifications and as directed by the Engineer-in-charge.

Providing and fixing Fancy type mirror with design Border with 6mm thick hard board backing all as directed by the Engineer-in-charge

Extra for providing and fixing mirrors with approved make- stainless steel 304 grade STUDS (with wall spacers) complete all as per specifications and as directed by the Engineer-in-charge

Providing and fixing sensor based LIQUID SOAP DISPENSER in all respect as per specifications and as directed by the Engineer-in-charge. Note : Tentative/suggested make for the guidance of the bidder (s) : M/s. EURONICS ES-05 or approved equivalent make

Providing and fixing C.P brass towel rail of approved make 600 mm long complete fixed to walls with 30 mm CP brass screws with concealed fitting arrangement all as directed by the Engineer-in-charge.

Providing and Fixing CP brass 100 mm dia shower rose with Shower arm of Specified make as per specifications and as directed by Engineer-in-charge complete

Providing and fixing white vitreous china flat back half stall urinal size 580x380x350 mm / 610 mm with Push cock of approved make with CP brass flush pipe unions, heavy quality C.P. brass spreaders, C.P waste coupling with dome grating, clamps complete all as per specifications drawings and as directed by the Engineer-in-charge. Note : Tentative/suggested make for the guidance of the bidder (s) : M/s. Aquaseal model or approved equivalent make

Providing and fixing heavy quality C.P. Brass health faucet with 1.50 metres long flexible hose (hand shower) of approved make with wall brackets and type as per specifications and as directed by the Engineer-in-charge

Providing and fixing Chinaware Half round Urinal channel 100 / 150 mm dia with or without dead ends set in C.M 1:3 laid to proper slope & grade including finsihing the joints with polymer based tile grout mix as per drawing and as directed by the Engineer-in-charge

Providing and fixing cast iron nahani trap / floor trap of 100 mm inlet and 75 mm outlet, (weighing 5.80 Kg each), jointing with lead with the connection pipes, placing as per the drawings, embedding in cement concrete 1:2: 4 and making circular hole up to floor level using 110 mm O/D PVC pipes of 6 Kg / sq.cm pressure and fixing 1 No 125 mm dia C. P brass grating , complete all as specifications and drawings and as directed by the Engineer-in-charge

Providing and fixing Heavy quality flexible PVC waste pipe of following dia. (semi rigid or flexible) of approved make for sink or wash basin including PVC waste fittings etc. complete all as per specifications and as directed by the Engineer-in-charge- 32 mm dia flexible PVC (semi-rigid) waste pipe

Providing and fixing Heavy Quality 15 mm n.b CP Brass 3 in 1 bath mixer with polished finish, to control flow of hot and cold water, with provision for over head shower, with 115mm long bend pipe and flange of approved make and type and as directed by the Engineer-in-charge.

Providing and applying wall painting two coats on new work with premium plastic emulsion paint of approved brand to give an even shade, including a coat of approved cement primer, including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing , Wall painting with One coat on old work flat oil paint of approved make to give an even shade including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge.

Providing and Painting two coats of synthetic enamel paint on steel surfaces of approved brand and manufacture to give an even shade over a primer coat.including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing and painting walls with (Two coats) of approved shade of high build protective, elastomeric water proof exterior grade paint of approved make of required shade, minimium dry film thickness of 250 microns acheived in two or more coats / as per manudacturer's specifications including preparation of the surfaces by scrapping / wire brush, scaffolding complete. Primer coat will be with approved make with water in ratio of 1:2 and 2 coats of finishing coat without water all as directed by Engineer-in-charge.

Providing and treating the OLD surface using ANTI-FUNGAL treatment in the following operations: (i) entire old paint to be scrapped out, (ii) The neeru / cement punning to be removed by chipping completely, (iii) one coat of Antifungal chemical having high degree of Santroprite (Sodium Chloro Penta Chlorophenate with diluant & additives) to be applied, (iv) entire surface to be finished with White cement based Wall putty of approved make to get uniform undulation free surface; complete as directed by the Engineer-in-charge. Note: 1. Old paint will be removed thoroughly either mechanically or by wire brush before application of primer and paint coats and cost of which shall be deemed to be included in the quoted rate. 2.Quoted rate for shall include for cost of covering existing material/furniture/equipments/devices with plastic sheet, removing the old paint by mechanical wall sander/scrubber machine, and cleaning the area as directed by the Engineer-in-Charge.

Providing and painting, finishing with antifungal paint of approved make with two coats over treated surface all as per manufacturer's specifications and as directed by the Engineer-in-charge Note: 1. Old paint will be removed thoroughly either mechanically or by wire brush before application of primer and paint coats and cost of which shall be deemed to be included in the quoted rate. 2. Quoted rate for shall include for cost of covering existing material/furniture/equipments/devices with plastic sheet, removing the old paint by mechanical wall sander/scrubber machine, and cleaning the area as directed by the Engineer-in-Charge.

Providing wood work in frames of doors, windows, clear story openings and other frames, wrought framed and fixed in position of required size and shape including sawing, jointing,making rebates for shutters, making grooves as shown in the drawings, finishing the surfaces to the required finish all as per specifications and drawings including necessary MS hold fasts 40 mm X 3 mm thick / Aluminium angle of required ISA Section , 200 mm long / with coach screws including protective painting to the suface that will come in contact with walls, joining materials, labour etc. complete all as per specifications and as directed by the Engineer-in-charge- Second class teak wood

Providing and fixing WATER PROOF MARINE PLY of any approved brand as per IS 710: 2010. The rates are including the cost of screws, washers etc complete providing and fixing hard wood leaping around board in walls etc.

By using 12 mm thick water proof marine ply.

By using 19 mm thick water proof marine ply.

Providing and fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS:2046 Type S including cost of adhesive, labour etc. complete as directed by Engineer in Charge.

Providing and fixing decorative high pressure 1.5 mm thick laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS:2046 Type S including cost of adhesive, labour etc. complete as directed by Engineer in Charge.

Providing and fixing decorative high pressure 1.0 mm thick laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS:2046 Type S including cost of adhesive, labour etc. complete as directed by Engineer in Charge.

Extra for providing and fixing flush doors with decorative veneering in one side and commercial plywood finish in other side.

Providing and applying French spirit polishing for wooden sufaces with two coats on new works including a coat of wood filler to form a uniform neat finish as directed by the Engineer -in-charge and / or as per the specifications complete as directed by the Engieer-in-charge

Providing and painting with PU paint or polish on wood/metal/plastic surface as per manufacturer's instructions with thickness of 1mm achieved in two or three coats, matte or glossy finish including preparation of surface by removing all contaminants, sanding if necessary and making it even, for better adhesion & ensure thorough stirring to get consistent texture, evenly applied and properly cured complete as per specifications and as directed by the Engineer-in-charge.

Providing and fixing of required size of wooden moulded beading to using 2nd class teak wood to door and window frames with iron screws, plugs and priming coat on unexposed surface complete all as directed by Engineer-in-charge.

Providing and fixing heavy duty stainless steel 3 section telescopic full extension ball bearing drawer slide of size 20", load capacity 45kg all as directed by Engineer-in-charge.

Providing and fixing fancy Stainless Steel/Brass D-handle for cabinet/drawer with satin finish with 100/150 mm long with SS screws etc. complete as per direction of Engineer-in-Charge.

100mm long D-handle

150mm long D-handle

Providing and fixing durable heavy duty multipurpose furniture drawer lock of 40mmx40mm for 22mm panel thickness with atleast two keys, with SS screws complete as per direction of Engineer-in-Charge.

Providing and fixing durable heavy duty brass wardrobe lock of size 25mm, cabinet with nickel plated finish, with atleast two keys, with SS screws complete as per direction of Engineer-in-Charge.

Providing and fixing heavy duty stainless steel soft close 4-hole full overlay cabinet hinges with stainless steel screws etc. complete as directed by the Engineer-in-charge.

Providing and fixing 25 mm S.S curtain rods of 1.25 mm thick with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete

Providing and fixing heavy duty stainless steel bed lift mechanism comprising pair of 5mm thick, 1m long frame attached with a pair of pneumatic gas lifter pump each of size 20 inches having combined capacity of upto 225kg with maximum lifting height of 60inches, having a complete as directed by the Engineer-in-charge.

Carrying out Civil Engineering works like surveying & leveling, checking of formwork fabrication, reinforcement fabrication as per drawings, witnessing sample retrieval & testing for various construction materials, ensuring concrete ingredient ratio at batching plant and pouring of appropriate grade of concrete in plain and reinforced concrete works, ensuring proper mixing of approved ingredients & waterproofing admixtures for mortars and brickwork, plaster, flooring & waterproofing works and other civil & PH works including supervision of construction safety as per BARC specifications & relevant documentation, compiling, binding and preparation of tender documents & Agreements overall as directed by Engineer-in-Charge. Note : (1) Each Job shall be carried out by one qualified Degree holder Civil Engineer with 2 (Two) years experience or Diploma holder with 5 (Five) years experience (Licentiate in Civil/Construction Engineering / Technology) conducted by Board of Technical Examinations / University / Autonomous Govt. / Govt. recognized recognized Polytechnic/ Institute. (2) Deployment: The contractor shall deploy one Engineer for each job for minimum 26 working days per month for minimum 8 ½ hours per day with 30 minutes of break, in General (Ist / IInd) or on Round the clock shift including Saturdays, Sundays & holidays whenever necessary as per the discretion of the Engineer-in-Charge during the contract period. In case of emergency works like continuous pouring of concrete or shutdown/maintainance work, the Engineer will have to stay longer occasionally as per the instruction of the Engineer in-charge. No additional payment will be made on this account. (3) Period of work: The contractor shall carry out number of Jobs per month as per requirement at site for the period mentioned in NIT. (4) Mode of measurement : Measurement will be per job basis. A single job shall be carried out by deploying one Engineer exclusively for the particular job. (5) Engineer should be engaged after scrutiny by EIC of CSS, ESG, BARC and approved by Competent authority and the deployed Engineer will report to BARC Engineer/ EIC. (6) The minimum notice period before change of engineer is 1 (one) month; failing which a compensation, for not providing technical support, of Rs. 1,915/- per day of shortfall in notice period will be levied on the contractor.

CARRYING OUT MANUAL MISC. CARPENTRY / PLUMBING / CIVIL / MASONRY JOBS like minor repairs, fixing fitting and fixtures etc. as and when required and as directed by the Engineer-in-charge Note: 1. Labours shall bring necessary carpentary / plumbing tools, minimum materials such as washher, taflon tape, rawlpludge, screws, clips etc. 2) Payment shall be made as per the Log book duly approved by the Enginner in charge. 3) Contrator shall arrange necessary Police Verification Certificate for the workers engaged for thess work. 4) The contractor shall deploy one skilled, semiskilled or unskilled person for each job for 8 1/2 hours per day with 30 minutes of break, in General (Ist / IInd) or on Round the clock shift whenever necessary as per the discretion of the Engineer-in-Charge during the contract period.

SKILLED CARPENTERY/PLUMBING/MASONRY JOB / WORKS with valid Police Verification Certificate for entire contract period.

SEMI-SKILLED CARPENTERY/PLUMBING/MASONRY JOB / WORKS with valid Police Verification Certificate for entire contract period.

UNSKILLED CARPENTERY/PLUMBING/MASONRY JOB / WORKS with valid Police Verification Certificate for entire contract period.

Providing and placing of medium back ergonomic mesh study chair of dimension 595mm(W) x 670mm (D) x 1125mm(H), upholstery material as high quality abrasion resistant, superior tear strength fabric mesh; premium high-density virgin foam cushion for comfortable seating; with pneumatic height (max 570mm) adjustment with BIFMA certified Class IV gas lift; self-weight multi-locking mechanism for recline; adjustable lumbar support for back; chrome base with castor wheels for stability and smooth linear & swivel movement; with armrest; with clearing drop test of 102 kgs; with minimum warranty of 5 years all as directed by Engineer-in-charge. Note : Tentative/suggested make for the guidance of the bidder (s) : M/s. DURIAN INDUSTRIES or approved equivalent make

Providing & installing at site Cafeteria chairs unwind type with moulded indoor grade Polypropylene compound seat of size 525*532 mm as per available technical specifications and direction by Engineer in Charge. Note : Tentative/suggested make for the guidance of the bidder (s) : M/s. GODREJ INTERIO or approved equivalent make ( Refer Detailed Technical Specification No TS-01)

Providing and supplying Orthopedic memory foam mattress of 6 inch thickness in required dimensions consisting high resilient viscoelastic polyurethane memory foam layers with soft non-allergenic, anti-microbial high gsm upholstery material all as per directed by Engineer-in-charge. Note : Tentative/suggested make for the guidance of the bidder (s) : M/s. DURIAN INDUSTRIES or approved equivalent make

Providing and placing room window curtain of sheer/light filtering/blackout type featuring elegant finish and modest design of polyester / fabric material and machine washable including all types of cost of material and manpower all as directed by Engineer-in-charge. Note : Tentative/suggested make for the guidance of the bidder (s) : M/s. GODREJ INTERIO or approved equivalent make

Providing and fixing heavy duty Stainless steel cloth hanger consisting of 6 hooks all as directed by Engineer-in-charge.

Providing & supplying of Pick-up Van / Utility Van for various areas for the requirements arising from time to time inside and outside BARC. The Pick-up Van / Utility Van of minimum five seaters capacity with the back side provision for transporting/ shifting of various construction / maintenance materials, machinaries and tools etc. and for other works including Driver as assigned and directed by Engineer-in-Charge. (8Hrs. a day or 60 km max as per certification of Engineer-in-Charge). Conditions: 1. The above rates shall be inclusive of cost of supply of Pick-up Van / Utility Van, Fuel, wages of Drivers and other consumables etc. 2. The Reporting time at the place of duty / as instructed by EIC shall be considered for the billing / measurement / payment. 3. In case the pick up van is parked inside BARC premises then the reporting time of the driver to EIC shall be considered for the billing/ measurement/ payment. 4. Break Down Hours as per actuals and Lunch break (30 min.) timings shall not be considered for payment. 5. Fraction of hours shall be rounded off to nearest half an hour at the time of preparing the Running / final bills 6. BARC being a restricted place, the driver should have good credentials and shall have valid Police Verification / Clearance Certificate (PVC), driving license and address proof. They should be in a position to understand Hindi / English / local language. 7. The make and model of the vehicle should not be more than 8 years old, roadworthy with all valid documents. 8. The vehicle shall be maintained in good running condition with good upholstery, fitness, good tyres and shall commensurate with the image of BARC. The tyres of the vehicles shall be replaced periodically for safe and incident-free driving. 9. The vehicle should be free from all sorts of defects and will be subjected to inspection by a representative of BARC whose decision shall be final and binding as regards suitability of that particular vehicle. 10. The vehicle should be a transport vehicle and preferably in white colour with a board "ON GOVERNMENT OF INDIA DUTY". 11. The cost of POL, maintenance and servicing of 'vehicle including replacement of parts, payment to the driver, Motor Vehicle taxes, comprehensive insurance, etc. shall be payable by the Contractor and BARC shall have no liability on these accounts. 12. The cost of damages to any Government movable/immovable property in and around the site shall be entirely borne by the Contractor. 13. The rates are inclusive of all taxes if any, excluding Goods & Service taxes (GST). 14. The contractor shall arrange adequate insurance coverage for his personnel. Department shall not be responsible for any liability arising out of any accident / injury caused to the driver while executing the job. 15. The contractor shall follow minimum wages act and other rules of Government of Maharashtra. 16. No revision of price shall be entertained during the period of contract. Per Day 2,600.00 17. Hours more / less than 8 Hrs. a day will be paid / deducted on pro-rata basis. 18. In case of absence of Driver/vehicle for entire week, a compensation of Rs. 3000 /- per week, for not providing the service, will be levied on the contractor for that week.

Carrying out Data Entry operations and assisting departmental Officer / Engineers, preparation of monthly and quarterly statements, dispatching and delivering documents/file movement and maintaining registers and documents, checking/preparation of agreements etc. as instructed by Engineer-In-charge. Notes: (1) Qualification: Each job shall be carried out by one data entry operator having minimum HSC pass (12th Standard) with complete knowedge of computer (like MS office, etc.) and should also be well conversant in English and Hindi language. (2) Deployment : The contractor shall deploy one Data entry operator for each job as Single Day work for 6 working days per week for minimum 8 ½ hours per day with 30 minutes of break, in General (Ist / IInd) shift including Saturdays, Sundays & holidays whenever necessary as per the discretion of the Engineer-in-Charge during the contract period. (3) Period of work: The contractor shall carry out number of Jobs per day as directed by Engineer-in -Charge. (4) Mode of measurement : Measurement will be per job basis. A single job shall be carried out by deploying one Data entry operator exclusively for the particular job. (5) The Data entry operator should be engaged after scrutiny by EIC of CED, BARC and approved by Competent authority and the deployed Data entry operator will report to BARC Engineer/ EIC. (6) The minimum notice period before change of Data entry operator is 1 (one) month; failing which a compensation, for not providing technical support, of Rs. 1,276/- per day of shortfall in notice period will be levied on the contractor.

Providing and fixing Anchor fastener HST stud type M-12X115mm long, including drilling in concrete as per requirement for fixing EPs or other structures all as specified by the manufacturer complete all as per specifications and drawings and as directed by EIC. Note : Tentative/suggested make for the guidance of the bidder (s) : M/s HILTI Anchor HST Stud type M-12X115mm long or approved equivalent make

Supplying of approved quality Fevicol pack of 1kg as directed by EIC.

Providing soft drawn copper tubes of sizes as per technical specification (Refer Detailed Technical Specification No TS-02)

Providing PVC braided flexible drain pipe of 5/8" dia (Refer Detailed Technical Specification No TS-03)

Providing & installing rigid u-PVC piping with fittings (Refer Detailed Technical Specification No TS-04)

Providing PVC trunking of 100mm x 50mm cross sectional size (Refer Detailed Technical Specification No TS-05)

Providing 04 nos. GI nut-bolts & washer along with rubber pad for ODU installation (Refer Detailed Technical Specification No TS-06)

Providing elastomeric close cell nitrile rubber insulation, adhesive & tape as per following: (Refer Detailed Technical Specification No TS-07)

Sleeve type insulation of 1/4 inch dia & 13 mm thickness

Sleeve type insulation of 1/2 inch dia & 13 mm thickness