Bhabha Atomic Research Centre Tender

25 mm n.b.

Providing and fixing brass ball cock approved Equivalent heavy quality of following sizes with arm rod and Plastic Ball floats complete as per specifications and as directed by the Project Engineer.

25 mm n.b.

32 mm n.b.

40 mm n.b.

Providing and fixing C.P brass bib cock of heavy quality of specified / approved make as per specifications and as directed by the Engineer-in-charge 15 mm dia bib cock of approved type and make.

Providing and fixing Heavy quality flexible PVC waste pipe of following dia. (semi rigid or flexible) of approved make for sink or wash basin including PVC waste fittings etc. complete all as per specifications and as directed by the Engineer-in-charge 32 mm dia flexible PVC (semi-rigid) waste pipe

Providing and fixing heavy quality C.P .brass waste coupling of following dia for wash basin and sink, of approved make, size and quality all as directed complete.

CP brass waste coupling 32 mm dia of approved make Half threaded or full threaded as per requirement.

CP brass waste coupling 38 mm dia of approved make Half threaded or full threaded as per requirement.

Providing and fixing heavy quality CP brass bottle trap 31 / 32 mm of approved make single piece moulded with height of 270mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal,of approved make for wash basins / urinal etc all as per specifications and directed by the Engineer in charge.

Providing and fixing 32 mm PVC Bottle trap of Approved Make in labs including removing the damaged bottle traps, fixing the new bottle trap.

Providing and fixing Brass 15 mm C.P presstomatic series auto shut urinal flush cock of approved make and quality

Providing and fixing 15 mm C.P brass urinal spreader size with 1/2" BSP thread and shapes, weighing not less than 60 gm of approved make and type.

Removing of existing damage waste coupling and Providing and fixing 32mm CP brass dome type waste coupling for urinal as directed at site by the Project Engineer.

Providing and fixing C.P brass Angle cock of heavy quality of specified / approved make, for wash basin inlet / flush cistern etc. as per specifications and as directed by the Engineer-in-charge. 15 mm n.b CP brass Angle cock of approved make

Providing and fixing 15 mm C.P brass 2 in 1 bib cock and Angle cock combination of Heavy Quality of approved make as per specifications and as directed by the Engineer-in-charge.

Providing and fixing cast iron nahani trap / floor trap of 100 mm inlet and 75 mm outlet, (weighing 5.80 Kg each), jointing with lead with the connection pipes, placing as per the drawings, embedding in cement concrete 1:2: 4 and making circular hole up to floor level using 110 mm O/D PVC pipes of 6 Kg / sq.cm pressure and fixing 1 No 125 mm dia C. P brass grating , complete all as specifications and drawings and as directed by the Engineer-in-charge.

Providing, laying , jointing, fixing and testing heavy quality ( (ISI Marked C-Class) Galvanised Iron pipes and ISI marked fittings like, tees, elbows, bends, unions, nipples,reducers etc. as required for the work, including testing the pipes and fittings for 10.00 Kg / Sq.Cm hydraulic pressure with a minimum period of two hours duration with clean water, including cutting , threading, jointing with hemp yarn, white lead, jointing teflon tape, chasing walls and making good by filling with concrete 1:3:6, complete all as per specifications and drawings, including two coats of anti corrosive bitumastic paint, all as directed by the Engineer-in-charge. Pipes with ISI marked 'C' -Class heavy quality pipes of approved make.

15 mm dia G.I pipe

20 mm dia G.I pipe

25 mm dia G.I pipe

32 mm dia G.I pipe

40 mm dia G.I pipe

50 mm dia G.I pipe

Providing and fixing heavy quality ISI marked G.I. union in G.I pipe lines including threading the pipes and long threads suitable for union complete all as per specifications and as directed by the Engineer-in-charge.

15 mm n.b Union

20 mm n.b Union

25 mm n.b Union

40 mm n.b Union

50 mm n.b Union

Providing and fixing white vitreous china flat back half stall urinal size 580 x 380 x350 mm / 610 mm Aquaseal model of approved make with approved make 32mm C.P flush value with standard flush pipe and C.P. brass spreaders, 32mm urinal waste coupling with dome grating and clamp etc. including making G.I water line connection complete as directed by the Engineer-in-charge (Only G.I. pipes will be paid under relevant Item ) Single half stall urinal with C.P brass Flush valve.Note : For fixing flush valve 32 mm G.I water line provision to be made which will be paid under relevant Item .

Providing and fixing viterious China wash basin of approved make and colour with C.I. brackets, 15 m C.P. brass pillar tap of approved make,15 mm x 600mm long PVC Inlet connection, 32 mm heavy quality C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls and testing complete all as per specifications and as directed by the Engineer-in-charge.

White vitreous China wash basin size 630 x4 450 mm and equivalent sizes with single 15 mm C.P. brass pillar tap

White vitreous China wash basin size 550 x 400 mm/ 550 x 420 mm and equivalent sizes with single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china laboratory sink of size 530 x 430 x 180 mm with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass trap with C.P. brass unions complete including painting the fittings and brackets with 3 coats of white enamel paint over a coat of primer, cutting and making good the walls wherever required complete as per specifications and as directed by the Engineer-in-Charge.

Providing and fixing 32 mm Dia PVC 15 Kg / Sq.cm inlet connection for flush pipe connecting with W.C. pan from high level flushing cistern

Providing and fixing PVC rain water pipes conforming to relevant IS type B and PVC SWR fittings & specials conforming to relevant IS including jointing with seal ring / With PVC solvent adhesive including fixing in walls using clamps etc complete all as per drawings, specifications and as directed by the Engineer-in-charge.

SWR PIPE 90 mm O/D

SWR PIPE 110 mm O/D

SWR PIPE 160 mm O/D

Providing and fixing PVC washer for all type of taps to stop the flow of work. Complete all as directed. Washers to be supplied by Contractor.

Excavation in Trenches, for pipes & Sewers in all soils excepting soft & hard rock upto a depth not exceeding 1.5 m including shoring & dewatering if necessary & refilling in trenches with selected excavated material in layers not exceeding 25 cm consolidating etc. & disposing the surplus earth within a distance of 50 m.

Removing / dismanting the following sanitary appliances along with all connections, including chiselling and removing the embedded portions, all inter connections and proper plugging of the inlets and outlets to prevent water flow etc. from all the floor level, stacking of dismantled materials whithin 50 mtr. lead and as directed by Engineer-in-Charge.

Wash Basin

Mirror

Flushing cistern including connection and fittings

EWC/WC with flushing cistern including connection and fittings

Existing GI/CI/PVC etc. pipe line along with all fittings & specials includig the embedded parts, fixtures, by chieselling etc. complete as directed.

Providing and fixing square mouth S.W. gully trap complete with CI grating brick masonry chamber with water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.5 kg and frame to be not less than 2.70 kg as per standard design (Size of 150 x 100 mm size gully trap "P" type)

Lead charges for Debris 1 km -2km or part thereoff, by mechanical transport including loading unloading, stacking / levelling etc. Note: The rates in respect of this Item is applicable for NET Quantities arrived at after making deduction for voids @ 30% in respect of debris from corresponding STACK / TRUCK Measurement

Providing and fixing solid plastic seat of approved colour suitable to existing EWC with lid including CP brass / SS bolts, screws etc. for pedestal type W.C. pan complete as per specifications and as directed by the Engineer-in-charge

Removing chokage of IWC/EWC/Angle Indian WC/Wash basin/Urinal /Sink/Bottel trap/Nahani trap etc. upto Ist Inspection chambers and keeping all the lines operational/functional complete all as directed.

Providing and Fixing stainless steel signage plates of size 120mmx120mmx1.50mm of approved make as per design / sign required using SS screws complete all as directed by the Engineer in Charge. Note : Tentative / suggested make for guidance of bidder(s) : 'KICH' make or approved equivalent make. Any equivalent proposed shall have to match technical parameter / specification of the tentative / suggested make.

Providing and Fixing stainless steel soap dispenser of approved make using SS screws complete all as directed by the Engineer in Charge. Note : Tentative / suggested make for guidance of bidder(s) : ES04 of M/s Euronics Industries or approved equivalent make. Any equivalent proposed shall have to match technical parameter / specification of the tentative / suggested make.

Providing and laying Unplastized Chlorinated PVC (UPVC) pipes for wash basin drains. This includes Jointing of pipes and fitting with UPVC solvent cement & testing the joints complete all as per specifications, drawings and as directed by the Project Engineer.

40 mm outer dia UPVC pipe 10 kg/cm2 pressure

50 mm outer dia UPVC pipe 10 kg/cm2 pressure

Supplying Semi-skilled / Skilled man power along with necessary tools, machines etc. when decided by Engineer-in-charge to work for eight hours ( excluding lunch ) per day to carry out the Plumbing works allotted by Engineer-in-charge.

Skilled labour with valid PVC for entire contract period

Semi- Skilled labour with valid PVC for entire contract period Note:- 1) Unit of measurement shall be per man day per day ( i. e. Eight hours a day ) 2) :- Number of manpower requirement as and when required will be as per direction of Project Engineer.

Providing and fixing heavy quality stainless steel / C.P brass grating of approved equivalent make as specified for floor traps / nahani traps all as directed by the Engineer-in-charge

SS grating 125 mm dia

SS grating 150 mm square with frame

Supplying and fixing Cast Iron Man hole or Cast Iron Steps cover of approved make and weight as specified in the drawings or as directed by the Engineer in charge.

Providing & supplying of Pick-up Van / Utility Van for various areas for the requirements arising from time to time inside and outside BARC. The Pick-up Van / Utility Van of minimum five seaters capacity with the back side provision for transporting/ shifting of various construction / maintenance materials, machinaries and tools etc. and for other works including Driver as assigned and directed by Engineer-in-Charge. (8Hrs. a day or 60 km max as per certification of Engineer-in-Charge). Conditions: 1. The above rates shall be inclusive of cost of supply of Pick-up Van / Utility Van, Fuel, wages of Drivers and other consumables etc. 2. The Reporting time at the place of duty / as instructed by EIC shall be considered for the billing / measurement / payment. 3. In case the pick up van is parked inside BARC premises then the reporting time of the driver to EIC shall be considered for the billing/ measurement/ payment. 4. Break Down Hours as per actuals and Lunch break (30 min.) timings shall not be considered for payment. 5. Fraction of hours shall be rounded off to nearest half an hour at the time of preparing the Running / final bills 6. BARC being a restricted place, the driver should have good credentials and shall have valid Police Verification / Clearance Certificate (PVC), driving license and address proof. They should be in a position to understand Hindi / English / local language. 7. The make and model of the vehicle should not be more than 8 years old, roadworthy with all valid documents. 8. The vehicle shall be maintained in good running condition with good upholstery, fitness, good tyres and shall commensurate with the image of BARC. The tyres of the vehicles shall be replaced periodically for safe and incident-free driving. 9. The vehicle should be free from all sorts of defects and will be subjected to inspection by a representative of BARC whose decision shall be final and binding as regards suitability of that particular vehicle. 10. The vehicle should be a transport vehicle and preferably in white colour with a board "ON GOVERNMENT OF INDIA DUTY". 11. The cost of POL, maintenance and servicing of vehicle including replacement of parts, payment to the driver, Motor Vehicle taxes, comprehensive insurance, etc. shall be payable by the Contractor and BARC shall have no liability on these accounts. 12. The cost of damages to any Government movable/immovable property in and around the site shall be entirely borne by the Contractor. 13. The rates are inclusive of all taxes if any, including Goods & Service taxes (GST). 14. The contractor shall arrange adequate insurance coverage for his personnel. Department shall not be responsible for any liability arising out of any accident / injury caused to the driver while executing the job. 15. The contractor shall follow minimum wages act and other rules of Government of Maharashtra. 16. No revision of price shall be entertained during the period of contract. 17. Hours more / less than 8 Hrs. a day will be paid / deducted on pro-rata basis. 18. In case of absence of Driver/vehicle for entire week, a compensation of Rs. 3000 /- per week, for not providing the service, will be levied on the contractor for that week.

Providing and fixing 15 mm PVC inlet connection suitable for hot and cold water 600 mm long with nuts and washers complete for wash basins/ Urinals etc. with all necessary acessories complete as directed by the Engineer-in-charge

Providing, supplying and fixing JET spray with 1.00 metre long flexible tube connection in European / Anglo Indian closet under seat cover fixtures complete all as specified and as directed by the Engineer-in-charge

Providing and fixing white vitreous china European type Water Closet with 'P' or 'S' Trap with solid seat and lid of approved make, 10 litre low level white PVC flushing cistern with manually controlled device (handle lever) conforming to IS:7231, flush bend, fixing EWC with C.P brass screws, 15 mm PVC heavy quality inlet connection of 450 mm long, including testing , commissioning & cleaning etc. complete all as per drawings and specifications and as directed by the Engineer-in-charge E.W.C. pan in White colour with ISI marked white solid plastic seat and lid.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS 15622 of approved make. shade and colour of size ranging from 300 - 600 mm long and 300 mm - 600 mm wide and thickness not less than 6 mm as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (using crushed sand), setting the tiles in cement slurry and pointing the joints with matching colour Tile grout of approved make of matching shade including using PVC tile trim in the exposed corners, complete as per drawings, patterns and specifications complete as directed by the Engineer-in-charge.

Providing and fixing 1st quality ceramic glazed floor tiles of minimum 300 - 600 mm long and 300 - 600 mm wide and thickness not less than 6 mm conforming to IS 15622 of approved make in all colours and shades as approved by Engineer-in-charge over a bed of 20 mm thick bed of cement mortar 1:4 (using crushed sand) and jointing with grey cement slurry including pointing with white cement based Tile grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Enginner-in-charge

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 100 m lead For thickness of tiles above 25 mm and up to 40 mm

Providing and fixing 6 mm thick mirrors of size 600 x 450 mm of approved make with bevelled edges complete with 6 mm thick asbestos sheet back ground fixed to walls with C.P. brass screws and concealed washers complete. all as per specifications and as directed by the Engineer-in-charge .

Extra for providing and fixing mirrors with approved make- stainless steel 304 grade STUDS (with wall spacers) complete all as per specifications and as directed by the Enginner-in-charge

Providing and constructing Brickwork in cement mortar 1:6 using crushed sand with Flyash / Flyash Lime bricks with minimum 70 kg / Sq. cm strength of approved make and size in Sub structure including, scaffolding, raking out joints, curing, cleaning complete all as per specifications and drawings.

Providing 12 mm thick Internal plastering in cement mortar 1:4 without cement punning (using crushed sand) finished smooth, including sieving of sand to required fineness, preparation of the surface, scaffolding, curing all as per specifications, drawings and as directed at site complete.

Extra for cement punning for all types of mixes complete all as per specifications and as directed.

Replacement existing damaged part of plastic cistern and installing the new part carefully. Including cost of materials, tools, tape etc. complete all as directed.

Adjustment of internal system.

Replacement of internal cistern fittings for PVC flush tanks

Replacement of Syphon

Providing Reinforcement Steel for reinforced cement concrete at all levels including supplying, preparation of bar bending schedules, cutting, bending, transporting, fixing, tieing in position with PVC coated G.I binding wire, all labour charges, cost of cover blocks in specified grade of concrete etc. complete as per specifications and drawings.

Using TMT bars of specified grades all dia bars. TMT bars to be supplied by the contractor manufactured by approved brands of BARC only, confirming to IS:1786

Providing , centering ,shuttering Form work using PVC film faced plywood to get a neat form finish surface for all types of structures including necessary strutting, proping, staging, supports etc and deshuttering the same after the specified time all as per drawings, specifications and as directed by the Engineer-in-charge at all levels

For Super Structure

Providing and laying in position Reinforced Cement Concrete (RCC) of grade M-30 using 20mm maximum size aggregates and crushed sand of approved quality including admixtures of approved brand and quality (plasticiser or super plasticiser) if required, including weigh batching, mechanical mixing, transporting, placing, vibrating, consolidation, finishing, curing etc. complete but excluding the cost of centering, shuttering and reinforcement complete as per specifications up to Plinth Level.Minimum cement content 425 Kg/Cum for OPC and 465 Kg/Cum for PPC.

Extra for RCC all grades in super structure up to 20.00 metre height

Extra for RCC Using Ready Mix Concrete from outside project area including transporting and pumping from approved batching plants .

Providing and Fixing SMC Panel water storage Tank of approved manufactured as per IS 14399 made out of Hot Pressed Moulded Sheet Moulding Compound (SMC) panels of size 1m x 1m and 1m x 0.5m as per site requirement at required elevation. All the flanges of the panels should have 10 nos of holes for fastening and joining the panels to one another. Manhole should be provided on the roof of the tank with proper locking arrangemet with cover of dia 600mm. Panel should withstand hydrostatic pressure of at least 4 times the working load and should be provided with hot dip galvanized nut, bolts / washer and special sealant having excellent UV resistance as well as suitable for potable water. The roof should be supposed with pvc pipe of 110mm dia at every interval. The tank should have ladders inside and outside , provision of inlet, outlet, overflow / drain and fixing necessary Nozzles / Flanges provided with tanks are of G.I and Qty. is 1 each for Inlet /Outlet/Overflow 50mmNB & 100mm NB for outlet required length as per site conditions with double check nuts, washer etc. complete job as per directions of engineer-in-charge.

ISI Mark Prefabricated SMC Panel Tank in the size of 1m x 1m x 1m having 1 KL Capacity (1,000 Liter) including Installation of tank.