Western Coalfields Limited Tender

Item code 6.45.2, page 113 Half brick masonry with non modular fly ash lime Gypsum bricks (FALG Bricks) class designation 10, conforming to IS:12894, in superstructure above plinth level up to floor V level. Cement mortar in 1:4 (1 cement: 4 coarse sand).

Item code 15.2.2, page 248 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 m lead as per direction of Engineer-in-charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix).

Item code 13.16.1, page 223 6 mm cement plaster of mix: 1:3 (1 cement: 3 fine sand).

Item code 13.1.2, page 222 12 mm cement plaster of mix: 1:6 (1 cement: 6 fine sand).

Item code 11.3.1, page 187 Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate.

Item code 15.23.1, page 250 Dismantling tile work in floors & roofs laid in cement mortar including stacking material within 50 m lead. For thickness of tiles above 10 mm & upto 25 mm.

Item code 11.37, page 192 Providing & laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand), including pointing the joints with white cement & matching pigment etc., complete.

Item code 11.36, page 192 Providing & fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge, in skirting, risers of steps & dados, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) & jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Item code 17.1.1, page 287 Providing & fixing water closet squatting pan (Indian type WC pan) with 100 mm sand cast iron P or S trap, 10 litre low level level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS:7231, with all fittings & fixtures complete, including cutting & making good the walls & floors wherever required: White vitreous china Orissa pattern WC pan of size 580x440 mm with integral type foot rests.

Item code 19.1.2, page 335 Providing, laying & jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete: 150 mm diameter.

Item code 12.41.2, page 210 Providing & fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS:13592 type A, including jointing with seal ring conforming to IS:5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter.

Item code 12.41.1, page 210 Providing & fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS:13592 type A, including jointing with seal ring conforming to IS:5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter.

Item code 14.5.1, page 237 Renewing glass panes, with putty & nails wherever necessary including racking out the old putty: Float glass panes of thickness 4 mm.

Item code 15.13.1, page 249 Taking out doors, windows & clerestory window shutters (steel or wood) including stacking within 50 m lead: Of area 3 sqm & below.

Item code 9.20.2, page 150 Providing & fixing ISI marked flush door shutters conforming to IS:2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood & well matched teak 3 ply veneering with vertical grains or cross bands & face veneers on both faces of shutters. 30 mm thick including ISI marked stainless steel butt hinges with necessary screws.

Item code 9.96.1, page 159 Providing & fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868), transparent or dyed to required colour or shade, with nuts & screws etc. complete: 300x16 mm.

Item code 9.97.3, page 159 Providing & fixing aluminium tower bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868), transparent or dyed to required colour or shade, with nuts & screws etc. complete: 200x10 mm.

Item code 9.100.2, page 160 Providing & fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: 100 mm.

Item code 21.3.1, page 356 Providing & fixing glazing in aluminium door, window, ventilator shutters & partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings & the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness.

Item code 13.80, page 229 Providing & applying white cement based putty of average thickness 1 mm, of approved brand & manufacturer, over the plastered wall surface to prepare the surface even & smooth complete.

Item code 14.42.1, page 241 White washing with lime to give an even shade: Old work (2 or more coats).

Item code 14.45.1, page 241 Distempering with oil bound washable distemper of approved brand & manufacture to give an even shade: Old work (1 or more coats).

Item code 14.66.1, page 243 Finishing walls with acrylic smooth exterior paint of required shade: Old work (2 or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface.

Item code 14.67.1, page 243 Finishing walls with Premium acrylic smooth exterior paint with Silicone additives of required shade: Old work (2 or more coat applied @ 1.43 ltr/ 10 sqm).

Item code 14.54.1, page 242 Painting with synthetic enamel paint of approved brand & manufacture of required colour to give an even shade: 1 or more coats on old work.

Item code 14.55.1, page 242 Painting with aluminium paint of approved brand & manufacture to give an even shade: 1 or more coats on old work.

Item code 14.58.1, page 242 French spirit polishing: 1 or more coats on old work.

Item code 14.53.1, page 242 Wall painting with plastic emulsion paint of approved brand & manufacture to give an even shade: 1 or more coats on old work.

Item code 2.32, page 75 Clearing grass & removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

Item code 16.3.10, page 253 Supplying & stacking at site. Moorum.

Item code 17.11.2, page 289 Providing & fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste & 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings & brackets, cutting 7 making good the wall wherever required: size 600x450x200 mm.

Item code 14.9, page 237 Renewal of old putty of glass panes (length).

Item code 18.49.1, page 321 Providing & fixing C.P. brass bib cock of approved quality confirming to IS:8931: 15 mm nominal bore.

Item code 21.1.1.1, page 355 Providing & fixing aluminium work for doors, windows, ventilators & partitions with extruded built up standard tubular sections/ appropriate Z sections & other sections of approved make conforming to IS:733 & IS:1285, fixing with dash fasteners of required dia & size, including necessary filling up the gaps at junctions, i.e. at top, bottom & sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred & jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings & the directions of Engineer-in-charge. (Glazing, panelling & dash fasteners to be paid for separately): For fixed portion. Anodised aluminium (anodised transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15).

Item code 21.1.2.1, page 355 Providing & fixing aluminium work for doors, windows, ventilators & partitions with extruded built up standard tubular sections/ appropriate Z sections & other sections of approved make conforming to IS:733 & IS:1285, fixing with dash fasteners of required dia & size, including necessary filling up the gaps at junctions, i.e. at top, bottom & sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred & jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings & the directions of Engineer-in-charge. (Glazing, panelling & dash fasteners to be paid for separately): For shutters of doors, windows & ventilators including providing & fixing hinges/ pivots & making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately). Anodised aluminium (anodised transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15).

Item code 23.8, page 372 Spreading of moorum in required thickness as per direction of Officer-in-charge (Cost of moorum to be paid separately).

Colour washing such as green, blue or buff to give an even shade. Old work (2 or more coats) with lime.

Total impact of GST for the purpose of CTC