MP State Livestock And Poultry Development Corporation Tender

Supplying and erection of stay set complete with 19/20mm.dia 1.8 metre long stay rod, turn buckle, ancher plate of size 300mm x 300mm x 7.5mm, thimble, stay clamps, bow tightener, 7/4.00 dia G.I. stay wire etc. in cement concrete M-10 (1 Cement : 3 Coarse and : 6 granded stone aggregate 40mm nominal size) foundation including excavation and back refilling etc. as required.(SOR I.No. 42.22)

Supply, fabrication and erection of Angle/Chanel/Flat iron fitting for over head line & sub-station etc such as 'D' bracket, cross arms, top clamp, 'V' cross arms, Back/Support clamps or other similar work etc. including nut bolts of required size, making holes, fabrication, welding, cutting, etc. and painting with one coat of red oxide paint & two coat of aluminium paint as required as per specification.(SOR I.No. 42.36)

Supplying and erection of 11kV (45 KN) Polymer disc insulator for 11kV overhead lines with galvanized insulator fittings, ball and socket type, and complete with galvanized strain clamp, bolts, nuts washer etc. as required. (SOR I.No. 42.47)

Supplying and drawing All Aluminum Alloy conductor (AAAC) of approved make confirming to IS 398-1979 Pt. IV, including binding at existing insulator, jointing, jumpering, tearing off, connecting etc. as required including clearing of obstacles (if any) AAAC 0.075 sq inch (80 Sq.mm Al. EQ. ) - (Raccoon) (SOR I.No. 42.5.3)

AAAC 0.1 sq inch (100 Sq.mm Al. EQ. ) - (Dog) ( SOR I No.42.5.4

Supplying and erection of 11kV (5 KN) Polymer pin insulator complete with long steel head G.I. pin, nut, washer etc. as required.(SOR I.No. 42.62)

Supply, laying and fixing of G.I. earth coil of 4mm dia G.I. wire having 120 turns of nearly 50mm dia. and 3 mt. long tail in existing pit duly earthed with pole etc complete as required as per specification.(SOR I.No. 42.62)

Supplying and fixing 33/11/0.4 KV enamel coated danger board size 200x250mm with clamp on existing HT/LT structure / poles.(SOR I.No. 42.63)

Supply & fixing anti climbing device with 2 ply G.I. barbed wire 1 Kg. per pole complete as per specification. (SOR I.No. 42.61)

Supplying and drawing guard wire/earth wire/bearer wire 13mm2 (4mm. Dia) G.I. including stringing, binding at existing insulators or brackets, jointing, jumpering, connecting & cradle etc. as required and clearing of obstacles (if any) (SOR I.No. 42.8)

Supplying, installing, testing and commissioning of 11/0.4K.V. 3 Phase 50 Cycle oil immersed, naturally cooled, outdoor type transformer connected delta on H.T. side andstar on L.T. side, hand operated off load Tap changer switch above 100 kVA, oil conservator with drain valve, plug 63 KVA and above, dehydrating silica gel breather on eye level, rating and diagram plate, two earthing terminal, liftinglugs, oil level gauge, drain valve with plug, temperature notexceeding 50ºC on load, oil filling hole with plug, fourunidirectional roller, arcing horns, explosion vent, terminalarrangement bushing on H.V. side and cable box on LVside, first filling of oil upto desired level and transformerinstalling on existing structure with all required materialsarrangement as required as per IS specification. Marked ISI& 3 Star rating Aluminium wound 100 kVA(SOR I.No. 42.64.1.3)

Supplying and erection of single piece non linear resistor polymer type lighting arrestor (Set of 3 Nos) for 3 wire, 11kVoverhead lines/sub-station with rated voltage of 9kV (rms)with a nominal discharge current rating of 10 KA and complete with galvanized clamping arrangement, G.I. bolts,nuts, washer etc. as required. (SOR I.No. 42.54)

Supplying installing, testing & commissioning of outdoor H.T., AB switch assembly set gang operated with brass contact parts, including required GI pipe operating rod, handle & locking arrangement on On-Off position conforming to IS complete with required material and installing on existing DP structure to complete the job as required as per specification.(Set of 3 nos.) 11 kV, 400A.(SOR I.No. 42.56.1 )

Supplying installing, testing & commissioning D.O. fuse assembly with brass part contact for 33 or 11/0.4 KV DP Structure set of 3 Nos. with fuse barrel i/c required fuse element & other materials as per specification on existing D.P. structure as required.101 11kV, (SOR I.No. 42.57.1 )

supplying and erecting earth pit of minimum bore dia. 150mm size , approved make Safe Earthing Electrode consisting Pipe-in-Pipe technology as per IS 3043-1987 made of corrosion free G.I. Pipes with constant ohmic valuesurrounded by highly conductive compound with high charge dissipation suitable for effective and maintenance free earthing as mentioned below : With 3 mtr. G.I. Pipes having outer pipe dia of 50mm having80-200 micron galvanizing, Inner pipe dia. of 25mm having200-250 Micron galvanizing, connection terminal dia.of12mm in nominal soil with 50 kg (Two Bag) Back fillingCompound. (SOR I.No. 37.40.2)

Supplying, fixing, testing & commissioning wall / floor mounted LT Panel primer coated with powder coated paint & provided with required gasket for dust / vermin proof withdegree of protection IP42 suitable for 415V 3 phase, 50 Hz,4 wire system fabricated out of CRCA sheet up to 2 mmthick (1.6 mm for doors) duly compartmentalized forincomer, bus section, outgoings, cable alleys & CT, PTAmpere Meter, Volt Meter, selector switches, Frequency Meter, phase indicating lamps, Energy Meter complete including cost of busbar supports, detachable cable glandplates, 2 earthing terminals, internal wiring & fixing of separately supplied MCBs, MCCBs , ACB, panel mountedChangeover switch / SFUs, etc. as required but excluding cost of bus bar strips, Ampere Meter, Volt Meter, Selector switch as per approved design & specification(SOR I.No. 29.33)

Supplying of ISI Marked and approved make of Moulded Case Circuit Breaker (MCCB) suitable for 3 phase,3 pole,50 Hz, 415 Volts, AC supply with respective interruptingcapacity (KA) at 415 Volts cited against their range standardconforming to IS – 8828 MCCB with Breaking Capacity 25 KA at 415 V Current Rating -200 Amps & 80% -100% adjustable (SOR I.No. 27.1.2.4)

Supplying & fixing of ISI marked DMC /Nylon Fuse holderfitting / Fuse Base for knife type HBC fuse Links of approvedmake & confirming to IS:13703-2-1 DMC /Nylon Fuse Base 160 Amps /415 Volts (SOR I.No. 25.18.5)

Supplying & fixing of High Breaking Capacity (HBC) FuseLinks knife (DIN) type as per IS : 13703 : 1993 & IEC :60269 :1986 with 80 kA breaking capacity of approved Make 125 Amp to 160 Amp (SOR I.No. 25.16.2)

Supply of XLPE Insulated power cable (confirming IS-7098 Part-I ) 1100 Volt grade, 1 core /2 core /3½ core/4 core ISI MARKED with Alu. Stranded /solid conductor UNARMOURED 1 Core 150 Sq.mm. (SOR I.No. 41.1.1.8)

Supplying and fixing of LT Panel accessories of approved make in existing LT Panel including connections etc.as required as per spececification Aluminium bus bar strips with PVC sleeves (SOR I.No. 29.34.5)

Supplying and drawing single core PVC insulated cable FR with copper multi strand conductor ISI marked in existing rigid PVC Casing-N-Capping / conduit in surface or concealed as per specification.1 X 2.5 sq mm (a) 1 X 2.5 sq mm (SOR I.No. 19.2.1)

Supplying and laying 25mm X 5mm G.I. strip at 0.5 Metre below ground level as strip earth electrode including soldering etc. as required. (SOR I.No. 37.8)

Supply of XLPE Insulated power cable (confirming IS-7098 Part-I ) 1100 Volt grade, 1 core /2 core /3½ core/4 core ISI MARKED with Alu. Stranded /solid conductor 3½ CORE ARMOURED 70 Sq.mm (SOR I.No. 41.1.8.4)

Laying of one number armoured / unarmoured power cable 1.1.kV grade of size exceeding 25Sq.mm but not exceeding120Sq.mmdirectinground includingexcavation in all soil / murrum / soft rock, sand cushioing, protective covering and refilling the pit etc. as required. (SOR I.No. 41.16)

Supply & fixing fencing of chain link mesh 100 x 100 mm,12 SWG GI wire for for D.P. structure electric sub-stationincluding single post of angle iron size 50x50x5mm, 2.5 mtlong should be provided up to 2.00 mt. apart or as required.The panel frame with required angle iron/ flat iron members/cross members including mesh welded in frame panel,shall be erected between the post. The angle iron post shallbe erected in cement concrete 1:2:4 ( 20 mm graded metal )foundation, including excavation of pit and refilling the same. The fencing shall be provided with one entrance gateincluding locking arrangement as required as perspecification. The height of fencing shall be 2 mt. aboveground level. Fencing shall be painted with required shade. (SOR I.No. 42.69)

Providing and installation of HTtrivector energy meter 3 phase 4 wire ,3*63.5 volt ib=5 amplma=10 amp with MRI/GSM(GPRS Compitile) facility class of accuracy 0.5 s with intelligent tested by mpvvco, test certificate will be submitted to the department ( make sems/genius/mpvvcl approved) Approved vid NITNo. 12 Dt 05-10-16

Supplying and fixing of LT Panel accessories of approved make in existing LT Panel including connections etc.as required as per spececification Digital Ampere Meter with CTs with selector switch (SOR I.No. 29.34.1)

Digital Volt Meter with selector switch & HRC fuse (SOR I.No. 29.34.2)